DALI-PWM Signal Converter D A P-04. Applications. Features

Transcription

1 SELV Bauar t gepruf t Sich erheit egelma ge od o s b e wac g ww w. tuv.com ID Features Universal AC input / Full range ( up to 305VAC) Convert DALI signal to PWM signal DALI addressable output channels Built-in push dim function Comply with DALI standards (IEC , 10, 07) PWM active high or active low selectable by jumper Linear or logarithm dimming curve selectable (meet IEC ) Dimming range : 1 100% Built-in relay for ON/OFF control of LED power supply Fully isolated plastic case Class Ⅱ power unit, no FG IP0 design No load power consumption < 0.5W ( Note.1) 3 years warranty Applications Indoor lighting Office lighting Decorative lighting Input signal : DALI or push dim Output signal : open collector PWM signal Description is a "DALI signal to PWM signal converter" which is suitable to use along with MEAN WELL's AC/DC LED power supplies which have 3-in-1 dimming function (110V / PWM / Resistance). Model Encoding DAP - 0 Output channel Series name

2 SPECIFICATION MODEL OUTPUT INPUT FUNCTION ENVIRONMENT SAFETY & EMC OTHERS NOTE NUMBER OF OUTPUT CHANNEL OUTPUT SIGNAL OUTPUT PWM LOGIC DIMMING RANGE VOLTAGE RANGE FREQUENCY RANGE AC CURRENT (Typ.) INRUSH CURRENT (Typ.) LEAKAGE CURRENT POWER CONSUMPTION (Typ.) INPUT SIGNAL REALY SWITCH WORKING TEMP. WORKING HUMIDITY STORAGE TEMP., HUMIDITY VIBRATION SAFETY STANDARDS EMC EMISSION EMC IMMUNITY MTBF DIMENSION PACKING PWM, 1KHz (Typ.) Active high or active low selectable by jumper ; Factory setting is active high 1 100% VAC 7 63Hz 0.1A COLD START 0A / 30VAC 1W DALI or push dim 0VAC / 8A, ON / OFF control refer to % RH non-condensing , 10 95% RH Hz, G 10min./1cycle, period for 60min. each along X, Y, Z axes Design refer to EN6137-1, EN , EN Clause 8/17/3/5 DALI STANDARDS Comply with IEC , 10, 07 WITHSTAND VOLTAGE I/P-O/P:3.75KVAC ISOLATION RESISTANCE <0.5mA / 0VAC I/P-O/P:>100M Ohms / 500VDC / 5 / 70% RH Compliance to EN55015, EN ,3 Compliance to EN ,3,,5,6,8,11, EN6157 light industry level (surge KV), criteria A 6.9K hrs min. MIL-HDBK-17F (5 ) 165*6*3mm (L*W*H) 0.16Kg; 8pcs/1.Kgs/1.1CUFT 1. No load power consumption<0.5w is measured at 30VAC.

3 Block Diagram EMI FILTER AUX POWER DA+ DA- DIM INTERFACE DALI INTERFACE MCU DIM ACTIVE HIGH/LOW SELECT RY+ RY- DIMMING OPERATION dim(primary side) Ignore Short push Long push Reset push To avoid reaction on AC spike Push to turn ON-OFF Dimming up or down Setting light to 100% <0.05 sec sec sec. >11 sec. Maximum length of the cable, from push button to last driver is 0 meter. Factory setting at 100%. When the light is lower than 10% it will always dim up, or when the light output is higher than 90% it will always dim down. DALI interface(primary side) DALI protocol including 16 groups and 6 addresses.

4 Connection of Dimming Operation DALI Dimming solution : with MEAN WELL's LED power supply MEAN WELL's AC/DC 1 Lamp 1 Lamp DALI controller DALI Bus DA+ DA- DIM (DALI-PWM signal converter) Up to channels Push Dimming Solution : with MEAN WELL's LED power supply MEAN WELL's AC/DC 1 Lamp 1 Lamp Push dimmer DIM Up to channels (DALI-PWM signal converter)

5 Dimming Connection Diagram with ON/OFF Function incorporates a built-in relay, allowing the control of Mean Well ON/OFF. This relay can be controlled only by. RY+ MEAN WELL's AC/DC RY- Fig 1 (DALI-PWM signal converter ) When the input AC current of Mean Well is greater than 8A, or the inrush current of that is greater than 50A, the users need to put up an additional external relay or magnetic switch. Please reference Fig for the configuration. Relay or magnetic switch RY+ MEAN WELL's AC/DC RY- Fig (DALI-PWM signal converter )

6 SYNCHRONIZATION OPERATION provides - channel outputs; every channel controls up to 0 units of Mean Well. The channels can thus control up to 80 units of Mean Well. (Note. 1) The dimming percentage of the Mean Well s controlled by the same channel of is the same. The dimming percentage per channel can be controlled independently. Maximum cable length between and LED power : Keep the voltage drop <0.5V D immingable D immingable D immingable Dimmingable 0 drivers(max.) 0 dr ivers(max.) DIM (DALI-PWM signal converter) Up to channels Note. 1 : When one of LED power is power OFF. It will cause all LED power output dimming down.

7 Mechanical Specification Case No. Unit:mm TB1 TB JP 1 1 Function Description of TB1 Terminal Pin No. Assignment(JP1) Pin No. Assignment 1, ACT-HI Pin No ,7 Function DA+ DA- RY+ / RY- Description AC Line connection. AC Neutral connection. Dimming input. One pushbutton connected between the and. DALI Signal positive. DALI Signal negative. Relay contact rating(max.) : 0VAC / 8A resistive "Short" when output duty cycle >0 ; "Open" when output duty cycle=0 Function Description of TB Pin No. 1, Function ACT-HI Description PWM active High / Low select. Short : Active High. Open : Active Low. Function Description of TB3 Terminal Pin No. Assignment(TB1) Terminal Pin No. Assignment(TB) Pin No. Assignment Pin No. Assignment Pin No. Assignment Pin No. Assignment 1 5 DA RY RY DIM+ DA+ - 8 DIM- Pin No. Function 1,3,5,7,,6,8 Description Dimming output Connect to (Blue) line of dimmingable LED power. Dimming output Connect to (White) line of dimmingable LED power. Installation Manual Please refer to : lationsearch.html