Cables and Connectors

Transcription

1 CHPTE Cables and Connectors This chapter describes the I/ interfaces, the data cables, and power cordsets required in using the LS00 enterprise TM switch. These facilities are described in the following order: Low-speed connectors and data cables for X., S-449, and V.5 serial interfaces. Circuit emulation access card (CEMC) connectors and data cables for 75-ohm and 0-ohm interfaces. Medium-speed connectors and data cables for the -port access card, the 4-port T/E access card, and the 8-port T/E access card. C-c connectors and data cables DDI connectors and data cables Ethernet connectors and data cables iber Ethernet access card (EC) connectors and data cables Console and modem connectors and data cables Country kits and power cordsets Signal diagrams are provided for each I/ connector and data cable. or most cables, two part numbers are provided in an associated table in the body of the chapter: the manufacturing number (which appears on the cable itself); and the order number (which is used in ordering the cable from Cisco Systems). Cables without associated order numbers are not available from Cisco Systems; such cables are widely available from other vendors as standard items. Cable Drawing Conventions igure - shows the conventions used in representing the signal paths in the LS00 I/ interface connectors and data cables illustrated in this chapter. Cables and Connectors -

2 Low-Speed Connectors and Data Cables igure - LS00 Cable Signal Diagram Conventions Cable wire Signal ground wire Protective ground wire Cable wire that is part of a twisted pair Twisted pair cable wires H70 Low-Speed Connectors and Data Cables This section presents the specifications for the connectors and data cables for the low-speed X., S-449, and V.5 serial I/ interfaces of the LS00 switch. This information is presented as follows: X. fantail connector - see the section X. antail Connector. S-449 fantail connector - see the section S-449 antail Connector. V.5 fantail connector - see the section V.5 antail Connector. DSU/CSU control ports on V.5 and S-449 fantails - see the section DSU/CSU Control Port Connector. Internal data cable for connecting a low-speed access card to a fantail - see the section Low-Speed ccess Card antail Cable. Data cable for connecting an X. fantail to an external X. device - see the section X. Interface Cable. Data cable for connecting an S-449 fantail to an external S-449 DCE device - see the section S-449 Interface Straight-Through Cable. Data cable for connecting two LS00 switches via their S-449 fantail interfaces, or for connecting an S-449 fantail to an external S-449 DTE device - see the section S-449 Interface Crossover Cable. Data cable for connecting a V.5 fantail to an external V.5 DCE device - see the section V.5 Interface Straight-Through Cable. Data cable for connecting two LS00 switches via their V.5 fantail interfaces, or for connecting a V.5 fantail to an external V.5 DTE device - see the section V.5 Interface Crossover Cable. X. antail Connector igure - shows the pin assignments of the X. fantail connector. Interface connector type: DB5 female Connectors per fantail: 8 (numbered 0-7) - LightStream 00 Site Planning and Cabling Guide

3 Low-Speed Connectors and Data Cables igure - X. Connector Pin ssignments Pinout DB-5 female S (B) I (B) (B) C (B) T (B) Signal GND S () I () () C () T () H87 S-449 antail Connector igure - shows the pin assignments of the S-449 fantail connector. Interface connector type: DB7 male Connectors per fantail: 4 (numbered 0 - ) igure - S-449 Connector Pin ssignments Pinout DB-7 male C SD ST D Signal GND T DM Signal GND DCE send timing- TT SC Protective GND SD+ ST+ D+ S+ T+ CS+ LL DM+ T+ + L DCE send timing+ TT+ TM Signal GND H88 Cables and Connectors -

4 Low-Speed Connectors and Data Cables V.5 antail Connector igure -4 shows the pin assignments of the V.5 fantail connector. Interface connector type: IS 59 male (4-pin block type) Connectors per fantail: 4 (numbered 0 - ) igure -4 V.5 Connector Pin ssignments Pinout B C NN KK IS 59 male Signal GND CTS DCD LL L D+ D T+ T DCEST DCEST+ TM B L V Z DD JJ NN D J N T X BB LL E K P U Y CC HH MM C H M S W EE KK Protective GND TS DS DT SD+ SD- TT+ TT- ST+ ST- H89 DSU/CSU Control Port Connector The S- DSU/CSU connector appears on both the V.5 and S-449 fantails. If you connect the control port to the craft port on a DSU/CSU device, you can use the csumon program to communicate with the DSU/CSU from an LS00 switch. Interface connector type: DB9 male Connectors per fantail: 4 (numbered 0 - ) igure -5 shows the pin assignments of the S- DSU/CSU control port connector. igure -5 S- DSU/CSU Control Port Pin ssignments 9 5 DB-9 male -4 LightStream 00 Site Planning and Cabling Guide Pinout D 7 TD Signal GND H90

5 Low-Speed Connectors and Data Cables Low-Speed ccess Card antail Cable This 00-pin data cable is used as the means of interconnection between the bulkhead connector of a low-speed X., S-449, or V.5 access card and the back of the fantail. The cable is available from Cisco Systems in three lengths. or ordering purposes, use the appropriate order number from the table below. Manufacturing No. Length rder No feet L00-CB-4= feet L00-CB-8= feet L00-CB-= Note that two such data cables are required to connect one X. fantail to a low-speed access card, while one only such cable is required to connect each V.5 or S-449 fantail to a low-speed access card. X. Interface Cable This cable is used to connect the X. fantail connector to an external X. device. The cable is available from Cisco Systems in three lengths. or ordering purposes, use the appropriate order number from the table below. Note Use the switches on the X. fantail to select a DTE or DCE interface for each port. Manufacturing No. Length rder No feet LS-CB-X-TC0= feet LS-CB-X-TC50= feet LS-CB-X-TC00= igure - is a signal diagram for the X. fantail cable. Cables and Connectors -5

6 Low-Speed Connectors and Data Cables igure - X. Cable Signal Diagram DTE end female DCE end male Protective GND Protective GND Transmit (T()) Transmit (T()) Transmit (T(B)) eceive (()) Transmit (T(B)) eceive (()) eceive ((B)) Signal element timing (S()) eceive ((B)) Signal element timing (S()) Signal element timing (S(B)) Signal element timing (S(B)) Signal GND 8 8 Signal GND Control (C()) Control (C()) Control (C(B)) 0 0 Control (C(B)) Indication (I()) 5 5 Indication (I()) Indication (I(B)) Indication (I(B)) Pin 8 Pin Pin Pin 8 Pin 5 DB-5 female connector Pin 9 Pin 9 DB-5 male connector H9 Pin 5 S-449 Interface Straight-Through Cable This cable is used to connect an S-449 fantail interface to an external S-449 DCE device. This cable is available from Cisco Systems. or ordering purposes, use the appropriate order number from the table below. Manufacturing No. Length rder No feet LS-CB-S4-TC0= feet LS-CB-S4-TC50= feet LS-CB-S4-TC00= igure -7 is a signal diagram for the S-449 fantail straight-through cable. - LightStream 00 Site Planning and Cabling Guide

7 Low-Speed Connectors and Data Cables igure -7 S-449 Straight-through Cables Signal Diagram Signal Ground (SG) Send Common (SC) Test Mode (TM) StandBy indicator (SB) Terminal Timing (TT+) Terminal Timing (TT ) DCE Send Timing+ (S/S) DCE Send Timing- (NS) Incoming Call (IC) Signal Quality (SQ) emote Loopback (L) Select Standby (SS) eceiver eady (+) eceiver eady ( ) Terminal eady (T+) Signal Ground (T ) Data Mode (DM+) Data Mode (DM ) Local Loopback (LL) terminal In Service (IS) Clear to Send (CS+) Clear to Send (CS ) eceive Timing (T+) eceive Timing (T ) equest to Send (S+) Signal Ground (S ) eceive Data (D+) eceive Data (D ) Send Timing (ST+) Send Timing (ST ) Send Data (SD+) Send Data (SD ) SPE SPE Signalling rate Indicator (SI) eceive Common (C) Protective Ground (PG) LightStream DTE end female DCE end male Signal Ground (SG) Send Common (SC) Test Mode (TM) StandBy indicator (SB) Terminal Timing (TT+) Terminal Timing (TT ) DCE Send Timing+ (S/S) DCE Send Timing (NS) Incoming Call (IC) Signal Quality (SQ) emote Loopback (L) Select Standby (SS) eceiver eady (+) eceiver eady ( ) Terminal eady (T+) Signal Ground (T ) Data Mode (DM+) Data Mode (DM ) Local Loopback (LL) terminal In Service (IS) Clear to Send (CS+) Clear to Send (CS ) eceive Timing (T+) eceive Timing (T ) equest to Send (S+) Signal Ground (S ) eceive Data (D+) eceive Data (D ) Send Timing (ST+) Send Timing (ST ) Send Data (SD+) Send Data (SD ) SPE SPE Signalling rate Indicator (SI) eceive Common (C) Protective Ground (PG) Pin 9 Pin Pin Pin 9 Pin Pin 0 Pin 0 H9 Pin 7 DB-7 female connector DB-7 male connector Cables and Connectors -7

8 Low-Speed Connectors and Data Cables S-449 Interface Crossover Cable This cable is used to connect two LS00 switches via their S-449 fantail interfaces, or to connect an S-449 fantail interface to an external S-449 DTE device. The cable is available from Cisco Systems. or ordering purposes, use an appropriate order number from the table below. Manufacturing No. Length rder No feet LS-CB-S4-TT8= feet LS-CB-S4-TT0= feet LS-CB-S4-TT50= feet LS-CB-S4-TT00= igure -8 is a signal diagram for the S-449 fantail crossover cable. -8 LightStream 00 Site Planning and Cabling Guide

9 Low-Speed Connectors and Data Cables igure -8 S-449 Crossover Cable Signal Diagram LightStream DTE end female DTE end female Signal Ground (SG) Send Common (SC) Test Mode (TM) StandBy indicator (SB) Terminal Timing (TT+) Terminal Timing (TT ) DCE Send Timing+ (S/S) DCE Send Timing (NS) Incoming Call (IC) Signal Quality (SQ) emote Loopback (L) Select Standby (SS) eceiver eady (+) eceiver eady ( ) Terminal eady (T+) Signal Ground (T ) Data Mode (DM+) Data Mode (DM ) Local Loopback (LL) Terminal In Service (IS) Clear to Send (CS+) Clear to Send (CS ) eceive Timing (T+) eceive Timing (T ) equest to Send (S+) Signal Ground (S ) eceive Data (D+) eceive Data (D ) Send Timing (ST+) Send Timing (ST ) Send Data (SD+) Send Data (SD ) SPE SPE Signaling rate Indicator (SI) eceive Common (C) Protective Ground (PG) Signal Ground (SG) Send Common (SC) Test Mode (TM) StandBy indicator (SB) Terminal Timing (TT+) Terminal Timing (TT ) DCE Send Timing+ (S/S) DCE Send Timing (NS) Incoming Call (IC) Signal Quality (SQ) emote Loopback (L) Select Standby (SS) eceiver eady (+) eceiver eady ( ) Terminal eady (T+) Signal Ground (T ) Data Mode (DM+) Data Mode (DM ) Local Loopback (LL) Terminal In Service (IS) Clear to Send (CS+) Clear to Send (CS ) eceive Timing (T+) eceive Timing (T ) equest to Send (S+) Signal Ground (S ) eceive Data (D+) eceive Data (D ) Send Timing (ST+) Send Timing (ST ) Send Data (SD+) Send Data (SD ) SPE SPE Signaling rate Indicator (SI) eceive Common (C) Protective Ground (PG) Pin 9 Pin Pin Pin 9 Pin 7 Pin 0 Pin 0 H9 Pin 7 DB-7 female connector DB-7 male connector Cables and Connectors -9

10 Low-Speed Connectors and Data Cables V.5 Interface Straight-Through Cable This cable is used to connect a V.5 fantail interface to an external V.5 DCE device. The cable is available from Cisco Systems. or ordering purposes, use an appropriate order number from the table below. Manufacturing No. Length rder No feet LS-CB-V5-TC0= feet LS-CB-V5-TC50= feet LS-CB-V5-TC00= igure -9 is a signal diagram for the V.5 fantail straight-through cable. -0 LightStream 00 Site Planning and Cabling Guide

11 Low-Speed Connectors and Data Cables igure -9 V.5 Straight-through Cable Signal Diagram Protective Ground (PG) Signal Ground (SG) equest To Send (TS) Clear To Send (CTS) Data Set eady (DS) Data Carrier Detect (DCD) Data Terminal eady (DT) ing Indicator (I) LTST (Cisco 4000) Local Loopback (LL) emote Loopback (L) Send Data (SD+) eceive Data D+) Send Data (SD+) eceive Data (D ) Terminal Timing (TT+) eceive Timing (T+) LightStream DTE end female B C D E H J K L M N P S T U V Terminal Timing (TT ) W eceive Timing (T ) X Send Timing (ST+) Y Z Send Timing (ST ) BB CC DD EE HH DCE Send Timing JJ DCE DS (T00) KK DCE Send Timing+ LL MM Test Mode (TN) NN DCE end male B C D E H J K L M N P S T U V W X Y Z BB CC DD EE HH JJ KK LL MM NN Protective Ground (PG) Signal Ground (SG) equest To Send (TS) Clear To Send (CTS) Data Set eady (DS) Data Carrier Detect (DCD) Data Terminal eady (DT) ing Indicator (I) LTST (Cisco 4000) Local Loopback (LL) emote Loopback (L) Send Data (SD+) eceive Data D+) Send Data (SD ) eceive Data (D ) Terminal Timing (TT+) eceive Timing (T+) Terminal Timing (TT ) eceive Timing (T ) Send Timing (ST+) Send Timing (ST ) DCE Send Timing DCE DS (T00) DCE Send Timing+ Test Mode (TN) Pin B Pin D Pin Pin C Pin C Pin Pin D Pin B H94 4-position female block connector 4-position male block connector Cables and Connectors -

12 Low-Speed Connectors and Data Cables V.5 Interface Crossover Cable This cable is used to connect two LS00 switches via their V.5 fantail interfaces, or to connect a V.5 fantail to an external V.5 DTE device. This cable is available from Cisco Systems. or ordering purposes, use the appropriate order number from the table below. Manufacturing No. Length rder No feet LS-CB-V5-TT8= feet LS-CB-V5-TT0= feet LS-CB-V5-TT50= feet LS-CB-V5-TT00= igure -0 is a signal diagram for the V.5 fantail crossover cable. - LightStream 00 Site Planning and Cabling Guide

13 Low-Speed Connectors and Data Cables igure -0 V.5 Crossover Cable Signal Diagram emale emale Protective Ground (PG) Signal Ground (SG) equest To Send (TS) Data Set eady (DS) Data Terminal eady (DT) Data Carrier Detect (DCD) Local Loopback (LL) emote Loopback (L) Send Data (SD ) eceive Data (D ) Send Data B (SD B) eceive Data B (D B) Terminal Timing (TT ) eceive Timing (T ) Terminal Timing B (TT B) eceive Timing B (T B) Send Timing (ST ) Send Timing B (ST B) DCE Send Timing B (DCEST B) DCE Send Timing (DCEST ) Test Mode (TM) B C D E J H L M N P S T U V W X Y Z BB CC DD EE HH JJ KK LL MM NN K B H E J C D L M NN P T S V U X W LL Z JJ BB CC DD EE HH KK Y MM N K Protective Ground (PG) Signal Ground (SG) Data Carrier Detect (DCD) Data Terminal eady (DT) Data Set eady (DS) equest To Send (TS) Local Loopback (LL) Test Mode (TM) eceive Data (D ) Send Data (SD ) eceive Data B (D B) Send Data B (SD B) eceive Timing (T ) Terminal Timing (TT ) eceive Timing B (T B) Terminal Timing B (TT B) DCE Send Timing (DCEST ) DCE Send Timing B (DCEST B) Send Timing B (ST B) Send Timing (ST ) emote Loopback (L) Pin B Pin D Pin Pin C 4-position female block connector Pin B Pin D Pin Pin C H95 4-position female block connector Cables and Connectors -

14 Circuit Emulation ccess Card (CEMC) Connectors and Cables Circuit Emulation ccess Card (CEMC) Connectors and Cables igure - shows the CEMC card and its associated data cable. To make a more secure connection, unscrew the top mounting screw (shown as in the figure) in the connector retention bracket and reposition it in the connector (as shown by in the figure). Next, tighten down the mounting screw to attach the data cable to the CEMC card securely (as shown by in the figure). inally, secure the cable to the CEMC bulkhead connector with the Velcro strip. -4 LightStream 00 Site Planning and Cabling Guide

15 Circuit Emulation ccess Card (CEMC) Connectors and Cables igure - CEMC ccess Card and Data Cable Connection E0 E E E 0 E E GND U E E 0 CEMC E E GND U E CEMC C E 0 E 0 E8 0 C E0 0 E 0 E 0 E8 0 E7 E Seat cable firmly in bulkhead connector E7 Secure cable with Velcro strip dd optional cable tie E H8 Cables and Connectors -5

16 X X Circuit Emulation ccess Card (CEMC) Connectors and Cables Table - shows the pinout assignments of the CEMC access card connector. Table - CEMC Bulkhead Connector Pinout ssignments eceive Transmit Port Tip ing Tip ing Not used Not used Not used 49 4 Not used Note: The information in this table is an extraction from igure 0 of merican National Standard T CEMC antail igure - shows the E fantail for 75-ohm CEMC applications. or convenience, igure - illustrates both the BNC and SMZ connector types that can be used in the E fantail. igure - E antail (75-ohm) GND 4 5 BNC connectors SMZ connectors X X X GND X4 X5 E NTIL 7 X X7 X8 X9 X0 X H efer to the LightStream 00 Hardware eference and Troubleshooting Guide for information regarding the configuration of the GND and X GND jumpers on the E fantail. - LightStream 00 Site Planning and Cabling Guide

17 Medium Speed Connectors and Cables E antail Data Cable This 50-pin cable is used as the means of interconnection between the 8-port bulkhead connectors on the CEMC card and the back of the E fantail. igure - illustrates this cable. The cable is available from Cisco Systems in three lengths. or ordering purposes, use the appropriate order number from the table below. Manufacturing No. Length rder No feet LS-CB-8E-4B= feet LS-CB-8E-8B= feet LS-CB-8E-B= igure - E antail Data Cable H5 Medium Speed Connectors and Cables This section describes the connectors and cables for the medium-speed (-port) access card, as well as the T and E (4-port and 8-port) access cards, as indicated below: External connectors on the medium-speed (-port) access card - see igure -4. External connectors on the T and E (4-port and 8-port) access cards - see igure -5. Cable harness used to connect the T/E access card to its associated dressing panel - see igure -. Data cable used to connect the medium speed access card and the T/E access cards to external devices - see igure -7. Cables and Connectors -7

18 Medium Speed Connectors and Cables Connectors on Medium-speed ccess Card Interface connector type: 75 ohm BNC jacks Connectors per access card: 4 ( receive and transmit) igure -4 shows the external coaxial connectors for the medium-speed (-port) access card. igure -4 Medium-speed ccess Card Connectors ront view H9 Connectors on T/E ccess Card Interface connector type: SMB connector at card; BNC connector at fantail Connectors per access card: 8 or, depending on the number of ports (either 4 or 8) on the T/E access card. Each port has one receive connector and one transmit connector. igure -5 shows the external connectors for the 4-port and 8-port versions of the T and E access cards. -8 LightStream 00 Site Planning and Cabling Guide

19 Cables and Connectors -9 Medium Speed Connectors and Cables igure -5 T/E ccess Card Connectors T ccess Card E ccess Card 4-Port 4-Port 8-Port 8-Port H8 X TC X X X H7 X TC X X X X 4 X 5 X X 7 H0 X EC X X X X 4 X 5 X X 7 H X EC X X X

20 Medium Speed Connectors and Cables T/E antail Cable Harness and Dressing Panel To interconnect patch panel/fantails to T/E access cards, both 4-port and 8-port coaxial cable harnesses are offered by Cisco Systems. In addition, both the 4-port and 8-port harnesses are available in 4-, 8-, or-foot lengths. The table below shows appropriate ordering information for the T fantail cable harnesses in desired port and length combinations. Manufacturing No. Ports Length rder No feet LS-CB-4T-4B= feet LS-CB-4T-8B= feet LS-CB-4T-B= feet LS-CB-8T-4B= feet LS-CB-8T-8B= feet LS-CB-8T-B= The table below shows appropriate ordering information for the E fantail cable harnesses in desired port and length combinations. Manufacturing No. Ports Length rder No feet LS-CB-4E-4B= feet LS-CB-4E-8B= feet LS-CB-4E-B= feet LS-CB-8E-4B= feet LS-CB-8E-8B= feet LS-CB-8E-B= The table below shows appropriate ordering information for the T/E coaxial cable dressing panel. Manufacturing No. rder No LS00-TE-T= igure - shows the T/E coaxial cable dressing panel, together with a T/E fantail cable harness. Note however that these components, although shown as connected in igure -, are available separately using the ordering information from the tables above. -0 LightStream 00 Site Planning and Cabling Guide

21 Medium Speed Connectors and Cables igure - T/E antail Cable Harness and Dressing Panel SMZ connectors PT 0 X PT X PT X PT X PT 4 X PT 5 X PT X PT 7 X BNC connectors H0 T/E 75-hm Coaxial Cable Where used: To connect two LS00 switches via their T/E access cards. To connect an LS00 T/E access card to an external device. To connect two LS00 switches via their T, E/PLCP, or E/G.804 medium-speed access cards. To connect an LS00 T, E/PLCP, or E/G.804 medium-speed access card to an external device. The T/E 75-ohm coaxial cable is available from Cisco Systems in four different lengths. Use the appropriate number from the table below for ordering purposes. Manufacturing No. Length rder No feet LS-CB-T-CX= feet LS-CB-T-CX5= feet LS-CB-T-CX50= feet LS-CB-T-CX00= igure -7 is a physical representation of 75-ohm T/E coaxial cable. igure -7 T/E 75-ohm Coaxial Cable 75-ohm coaxial cabling BNC plug BNC plug H99 Cables and Connectors -

22 C-C Connectors and Cables C-C Connectors and Cables igure -8 shows the external connectors on both the multimode and single mode C-c access cards. The multimode C-c and single mode C-c cables are described in separate sections below. Multimode interface connector type: Duplex SC Connectors per multimode access card: 4 ( per port; ports are numbered 0 and ) Single mode interface connector type: ST Connectors per single mode access card: 4 ( per port; ports are numbered 0 and ) igure -8 Connectors on Multimode and Single Mode C-c ccess Cards Supervisor module (magenta bar) Token ing switch module (orange bar) Token ing switch module (orange bar) Module filler H400 Multimode C-c Cable Where used: To connect a multimode C-c access card on an LS00 switch to another C-c device. Cisco Systems does not provide this cable; it is widely available from other vendors. The LS00 C-c interfaces operate at a wavelength of 00 nanometers. Multimode cables should conform to the following specifications: Standard: IS/IEC 94- Maximum path length (all cables in a connection, end to end): km Cabling:.5 micron core with an optical loss of 0-9 db, or 50 micron core with an optical loss of 7 db. - LightStream 00 Site Planning and Cabling Guide

23 C-C Connectors and Cables Note single fiber link should not mix.5 and 50 micron cable. Note Protective covers are provided for all C-c access cards and cable connectors. To shield connectors from dust and damage, keep covers on any connectors that are not being used. igure -9 shows a multimode C-c cable with simplex SC connectors. igure -9 Multimode C-c Cable with Simplex SC Connectors Simplex SC connectors emovable covers H40 Note Multimode C-c cables are available with both simplex SC connectors (as shown in igure -9) and duplex SC connectors; both connector types are compatible with LS00 multimode access cards. However, the use of duplex SC connectors is preferred because they are keyed in a way that prevents incorrect connections. Single Mode C-c Cable Where used: To connect a single mode C-c access card on an LS00 switch to another C-c device. Cisco Systems does not provide this cable; it is widely available from other sources. The LS00 C-c interfaces operate at a wavelength of 00 nanometers. Single mode cables should conform to the following specifications: Standard: EI class IVa Cabling: 8. micron core with an optical loss of 0- db and a maximum cable attenuation of 500 MHz/km at 00 nanometers. Note Protective covers are provided for all C-c access cards and cable connectors. To shield connectors from dust and damage, keep covers on any connectors that are not being used. Connector Type: ST igure -0 shows a single mode C-c cable with ST connectors. Cables and Connectors -

24 DDI Connectors and Cables igure -0 Single Mode C-c Data Cable with ST Connectors Simplex ST connector emovable covers H40 DDI Connectors and Cables igure - shows the media interface connectors (MICs) on an DDI access card. igure - Connectors on DDI ccess (C) Card and B connectors for one port H40 Each DDI port consists of two connectors, (red) and B (blue). DDI connectors are keyed to ensure proper connection of the cable to the access card. DDI Cable Where used: To connect an LS00 multimode DDI access card to another DDI device. Cisco Systems does not provide this cable; it is widely available from other vendors. The LS00 DDI interface operates at a wavelength of 00 nanometers. Cables should conform to the following specifications: Cabling:.5 micron core, graded-index fiber with an optical loss of db and a maximum cable attenuation of.5 db/km at 00 nanometers. Connectors: MIC -4 LightStream 00 Site Planning and Cabling Guide

25 Ethernet Connectors and Cables Maximum path length: (all cables in a connection, end to end): km Note Protective covers are provided for all DDI access card and cable connectors. To shield connectors from dust and damage, keep covers on any connectors that are not being used. igure - shows a physical representation of an DDI cable. igure - DDI Cable MIC connector emovable covers H404 Ethernet Connectors and Cables This section describes the Ethernet connectors and cables for the NP access card and the Ethernet access card. 5-pin Ethernet UI Connector igure - is a schematic diagram of the 5-pin Ethernet UI connector for the NP access card and the Ethernet access card (ports 0 and 7). The data cable for this connector is described in the section Ethernet UI Data Cable later in this chapter. Interface connector type: UI DB5 connector UI connectors per NP access card: one UI connectors per Ethernet access card: (numbered 0 and 7) Cables and Connectors -5

26 Ethernet Connectors and Cables igure - Ethernet UI Connector Schematic Diagram 9 Pinout 5 8 UI DB-5 female Collision+ Transmit+ eceive+ Voltage Common (SG) Collision Transmit eceive +V H405 Ethernet 0Base-T (J-45) Connector igure -4 shows the J-45 connectors and pinout assignments on the Ethernet access card. These connectors are used by the twisted pair (0Base-T) ports. The cables used with these ports are described in the section Ethernet 0Base-T Straight-Through Cable and the section Ethernet 0Base-T Crossover Cable. - LightStream 00 Site Planning and Cabling Guide

27 Ethernet Connectors and Cables igure -4 Ethernet J-45 Connectors and Pinout ssignments EC UI 0 TP 0 J-45 0BaseT pin assignments TP 7 UI 7 J-45 connectors for 0BaseT ports TD+ TD D+ D LT VCC H40 Cables and Connectors -7

28 Ethernet Connectors and Cables Ethernet UI Data Cable Where used: Connects an UI port on the NP access card or Ethernet access card of an LS00 switch to an Ethernet 0Base or 0Base5 transceiver. Cisco Systems does not provide this cable; it is widely available from other vendors. igure -5 shows a schematic diagram of the Ethernet UI data cable. igure -5 Ethernet UI Data Cable Schematic Diagram LightStream end male +V eceive Transmit Collision Voltage Common (SG) eceive+ Transmit+ Collision emote end female V eceive Transmit Collision Voltage Common (SG) eceive+ Transmit+ Collision+ Pin Pin 8 Pin 8 Pin Pin 9 Pin 5 Pin 5 H407 Pin 9 DB-5 male connector DB-5 female connector Ethernet 0Base-T Straight-Through Cable Where used: To connect an Ethernet access card on an LS00 switch to an Ethernet hub. To connect an Ethernet access card on an LS00 switch directly to another device on the Ethernet, such as a workstation, when the workstation port has a built-in crossover function. (See the note under the Ethernet 0Base-T Crossover Cable section later in this chapter). Cisco Systems does not provide this cable; it is widely available from other vendors. igure - shows a physical representation of the Ethernet 0Base-T (twisted pair) straight-through cable and provides a schematic diagram of its pinout assignments. -8 LightStream 00 Site Planning and Cabling Guide

29 Ethernet Connectors and Cables igure - Ethernet 0Base-T Straight-through Cable and Pinout ssignments H408 Pinout Transmit Data (TD+) Transmit Data (TD ) eceive Data (D+) eceive Data (D ) Transmit Data (TD+) Transmit Data (TD ) eceive Data (D+) eceive Data (D ) Ethernet 0Base-T Crossover Cable Where used: To directly connect an Ethernet access card on an LS00 switch to another device on the Ethernet, such as a workstation. Note Some MUs (medium access units) have a built-in crossover function and, therefore, use straight-through cables instead of crossover cables. Ports on such MUs are marked with the letter X. Cisco Systems does not provide this cable; it is widely available from other sources. igure -7 shows a physical representation of the Ethernet 0Base-T (twisted pair) crossover cable and provides a schematic diagram of its pinout assignments. igure -7 Ethernet 0Base-T Crossover Cable and Pinout ssignments H409 Pinout Transmit Data (TD+) Transmit Data (TD ) eceive Data (D+) eceive Data (D ) Transmit Data (TD+) Transmit Data (TD ) eceive Data (D+) eceive Data (D ) Cables and Connectors -9

30 iber Ethernet Connectors and Cable iber Ethernet Connectors and Cable This section describes the fiber Ethernet Connectors and data cable. iber Ethernet ccess Card Connectors igure -8 shows the bulkhead connectors on the fiber Ethernet access card. igure -8 iber Ethernet ccess Card Connectors EC X0 0 X X X CLSS LSE WNING UNTEMINTED PTICL CNNECTS MY EMIT DITIN. D NT VIEW WITH PTICL INSTUMENTS LSE KLSSE X4 4 X5 5 X X7 7 H9-0 LightStream 00 Site Planning and Cabling Guide

31 Modem/Console Connectors and Cables iber Ethernet ccess Card Data Cable Where used: To connect a multimode fiber (0Base-L) Ethernet access card in an LS00 chassis to another fiber Ethernet device. Cisco Systems does not provide this cable; it is widely available from other vendors. The LS00 fiber Ethernet interfaces operate at a wavelength of 850 nanometers. Multimode cables should conform to the following specifications: Standard: IS/IEC 94- Maximum path length (all cables in a connection, end to end): km Cabling:.5 micron core with an optical loss of 0-9 db, or 50 micron core with an optical loss of 7 db. Note single fiber link should not mix.5 and 50 micron cable. Connector Type: ST Note Protective covers are provided for all fiber Ethernet access cards and cable connectors. To shield connectors from dust and damage, keep covers in place on any connectors that are not being used. igure -9 illustrates the multimode fiber Ethernet access card data cable. igure -9 Multimode iber Ethernet Data Cable with ST Connectors Simplex ST connector emovable covers H40 Modem/Console Connectors and Cables igure -0 and igure - illustrate the modem and console connectors, respectively, on the switch card console/modem assembly. The data cable used for both the console and modem ports is described in the section S- Straight-Through Data Cable. S- Modem Connector Specification Interface connector type: DB5 male, DTE Connectors per assembly:, labeled MDEM Cables and Connectors -

32 Modem/Console Connectors and Cables igure -0 shows a schematic diagram of the S- modem port connector. igure -0 S- Modem Port Schematic Diagram Pinout 5 4 DB-5 male, DTE DCD GND DS I DT CTS 5 TS D 4 SD Protective GND 4 H40 S- Console Connector Specification Interface connector type: DB5 female, DCE Connectors per assembly:, labeled CNSL igure - shows a schematic diagram of the console port connector. igure - S- Console Port Schematic Diagram Protective GND SD D 4 DS 5 GND DB-5 female, DCE Pinout ST T LL DT L TT 5 TM H4 - LightStream 00 Site Planning and Cabling Guide

33 Modem/Console Connectors and Cables S- Straight-Through Data Cable Where used: To connect the LS00 console port or modem port to a console or modem. Cisco Systems does not provide this cable; it is widely available from other vendors. igure - shows a schematic diagram of the S- straight-through data cable. igure - S- Straight-through Data Cable Schematic Diagram Terminal/modem port end emale Console port/modem end Male Protective GND SD D TS CTS DS Signal GND DCD DT I Protective GND SD D TS CTS DS Signal GND DCD DT I Pin Pin Pin Pin Pin 5 Pin 4 Pin 4 H4 Pin 5 DB-5 female connector DB-5 male connector Cables and Connectors -

34 Country Kits and Power Cordsets Country Kits and Power Cordsets C-Powered LightStream 00 Systems variety of power cordsets is available for C-powered LS00 switches. These cordsets are available either with systems or as spare parts. This section enables you to choose the proper cordset for your LS00 site. If you are specifying a cordset as part of a new system order, refer to the LS00 Price List or the Products Catalogue and order the appropriate Country Power Kit. Doing so ensures that you will also receive the appropriate labels and instructions for the country of destination. If you want to check the cordset included in a specific Country Power Kit, refer to Table -, which cross-references cordset product numbers and Country Power Kit models. If you need to order a replacement cordset that is not part of a Country Power Kit, you must reference the cordset s part number. This part number (P/N) appears above each cordset illustrated in the following section entitled LightStream 00 C Power Cordsets. DC-powered LightStream 00 Systems DC-powered system does not use a detachable power cord. The DC power cord must be permanently wired to a DC power source. Therefore, in place of a Country Power Kit, each DC-powered system is shipped with a DC Mounting Kit, rder Number L00-PW-DC=. LightStream 00 C Power Cordsets Each LS00 C power tray is equipped with one recessed male power inlet. The power connectors follow IEC Standard 0 C0 and require cordsets with an IEC 0 C9 female connector. (ll cordsets offered by Cisco Systems for the LS00 switch have IEC 0 C9 female connectors.) Table - summarizes the specifications of C power cordsets. The table lists the country of use, cordset rating, plug type, part number, and Country Power Kit for each cordset. -4 LightStream 00 Site Planning and Cabling Guide

35 Country Kits and Power Cordsets Table - Specifications for LightStream 00 C Power Cordsets Country of Use Cordset ating Plug Type Mfg. Part Number Country Power Kit rder Number Canada, Mexico, Japan, and US 0 NEM 5-0P L00-PW-N= Canada, Mexico, Japan, and US 0 NEM L5-0P L00-PW-N5= Canada, Mexico, Japan, and US 0 NEM L-0P L00-PW-N50= Continental Europe, including ustria, Belgium, inland, rance, Germany, the Netherlands, Norway, Portugal, Spain, and Sweden CEE 7/ L00-PW-E= rgentina, ustralia, New Zealand, 5 S L00-PW-= and Papua New Guinea Denmark DI L00-PW-D= England, Hong Kong, Ireland, Malaysia, Scotland, Singapore, and Wales BS L00-PW-U= India and South frica 5 BS L00-PW-IN= Israel SI L00-PW-IS= Italy CEI L00-PW-I= Switzerland 0 SEV L00-PW-CH= P/N Used in Country Kit L00-PW-N= Cordset ating: 0, 5V or Canada, Japan, Mexico, and US Plug: NEM 5-0P Cordage: / SJT Connector: IEC 0 C9 Length:.5 m (8 feet inches) H4 Cables and Connectors -5

36 Country Kits and Power Cordsets P/N Used in Country Kit L00-PW-N5= Cordset ating: 0, 5V or Canada, Japan, Mexico, and US N G P/N Cordset ating: 0, 50V Used in Country Kit L00-PW-N50= or Canada, Japan, Mexico, and US Y X G Plug: NEM L-0P Cordage: / SJT Connector: IEC 0 C9 Locking Plug Length:.5 m (8 feet inches) H45 P/N Cordset ating:, 50V Used in Country Kit L00-PW-E= or Continental Europe: including ustria, Belgium, inland, rance, Germany, Holland, Norway, Portugal, Spain, and Sweden Plug: CEE 7/7 Cordage: x.5 mm Connector: IEC 0 C9 Length:.5 m (8 feet inches) H4 - LightStream 00 Site Planning and Cabling Guide

37 Country Kits and Power Cordsets P/N Cordset ating: 5, 50V Used in Country Kit L00-PW-= or rgentina, ustralia, New Zealand, and Papua New Guinea Plug: S-98 Cordage: x.5 mm Connector: IEC 0 C9 Length:.5 m (8 feet inches) H5 P/N Cordset ating: 0, 50V Used in Country Kit L00-PW-D= or Denmark Plug: 07--DI Cordage: x.5 mm Connector: IEC 0 C9 Length:.5 m (8 feet inches) H55 P/N Cordset ating:, 50V Used in Country Kit L00-PW-U= or England, Hong Kong, Ireland, Malaysia, Scotland, Singapore, and Wales Internal use Plug: BS Cordage: x.5 mm Connector: IEC 0 C9 Length:.5 m (8 feet inches) H47 Cables and Connectors -7

38 Country Kits and Power Cordsets P/N Cordset ating: 5, 50V Used in Country Kit L00-PW-IN= or India, South frica Plug: BS 54 Cordage: x.5 mm Connector: IEC 0 C9 Length:.5 m (8 feet inches) H40 P/N Used in Country Kit L00-PW-IS= Cordset ating:, 50V or Israel Plug: SI Cordage: x.5 mm Connector: IEC 0 C9 Length:.5 m (8 feet inches) H48 P/N Cordset ating:, 50V Used in Country Kit L00-PW-I= or Italy Plug: CEI - Cordage: x.5 mm Connector: IEC 0 C9 Length:.5 m (8 feet inches) H57-8 LightStream 00 Site Planning and Cabling Guide

39 Country Kits and Power Cordsets P/N Used in Country Kit L00-PW-CH= Cordset ating: 0, 50V or Switzerland Plug: SEV 0 Cordage: x.5 mm Connector: IEC 0 C9 Length:.5 m (8 feet inches) H49 Cables and Connectors -9

40 Country Kits and Power Cordsets -40 LightStream 00 Site Planning and Cabling Guide