Job Hazard/Safety Analysis For the Paint & Finish Worker
|
|
|
- Posy Reynolds
- 8 years ago
- Views:
Transcription
1 Job Hazard/Safety Analysis For the Paint & Finish Worker 1
2 INTRODUCTION Job Hazard/Safety Analysis for the Paint & Finish Worker is a partial list of known task performed by the professional paint and finish worker. We have placed task in alphabetical order and in a table format, listing each in a step-by-step sequence followed by the potential hazard and a recommended action or procedure. This is by no means an exhaustive list and is subject to modification. Additional comments may be added as more information becomes available. If you are asked to perform an occasional task, not listed with your job title, you can look up an individual task by returning to our Job Safety Analysis page and check the pulldown menu for Job Task. 2
3 APHABETICAL LIST OF TASK Page Air Compressor 4 Air Sprayer Chemicals (Pouring Handling) 5 6 Cleaning (Sweep & Mop) 7 Drum Handling (30-55 Gal.) 8 Hand Held Portable Power Tools 9 Heat Gun 10 Lifting/Carrying Objects 11 Paint Shaker Paint Stripper Portable Generator, Gasoline Powered Portable Heater, Electric Powered 15 Portable Heater, Gasoline Powered 16 Shop Vac(s) 17 Vise 18 3
4 Hazard Analysis: Air Compressor Shutdown and Isolate Unit Unit Activation during repair Auto start and/or human error Lockout/Tagout Routine Maintenance /Repair Routine Operation Noise Equipment Operation Hearing Protection Hand Injury Confined work areas, sharp edges Gloves Eye Injury Residual air pressure Goggles, safety glasses with side shields Electric Shock Improper operation and maintenance Manufacturer s instructions strictly followed, lock-out/tagout Noise Equipment Operation hearing protection Noise Equipment Operation hearing protection Eye Injury Blowing debris safety glasses w/side shields or goggles Goggles/Safety Glasses with side shield Hearing Protection Gloves Hazard Analysis: Air Compressor, Portable, Electric Routine Maintenance /Repair Routine Operation Electric Shock Improper operation and maintenance Unplug electrical cord and retain control of plug during repair/maintenance Noise Equipment operation hearing protection Trauma Eye Injury Improper use, uncontrolled release of compressed air Projectiles, flying debris appropriate nozzle for specific work activity, situational awareness Goggles or safety glasses with side shields Goggles or Safety glasses with side shield Hearing Protection 4
5 Hazard Analysis: Air Sprayer Shutdown and Isolate Unit Routine Maintenance/Repair Unit Activation during repair Auto start and/or human error Lockout/Tagout Noise Equipment Operation Hearing Protection Hand Injury Confined work areas, Gloves sharp edges Eye Injury Residual air pressure Goggles, safety glasses with side shields Electric Improper operation and Shock Maintenance Manufacturer s instructions strictly followed, lockout/tag-out Noise Equipment Operation hearing protection Routine Operation Noise Equipment operation hearing protection Safety Glasses with side shield Hearing Protection Gloves 5
6 Hazard Analysis: Chemicals (Pouring/Handling) Eye Injury Splash, fumes Goggles Contact irritation, burn or absorption Splash, skin contact Gloves (appropriate type for chemical), apron (if necessary), long sleeves Inhalation Breathing fumes Wear respirator if needed Face Splash Wear Face Shield (if necessary) Goggles Gloves protective Clothing (apron) Respirator (as needed) Face shield (if necessary) 6
7 Hazard Analysis: Cleaning (Sweeping/Mopping/Buffing) Trauma Projectiles, impact, chemical contact Situational awareness, gloves, protective clothing Foot Injury Dropped object on foot Wear safety shoes Inhalation Chemicals, dust Wear respirator or dust mask if needed Safety Shoes/boots Gloves (optional) protective Clothing (long pants recommended to prevent chemical splash on skin) Respirator or dust mask (as needed) 7
8 Hazard Analysis: Drum, Gal (Handling) Eye Injury Splashes Goggles (for handling exposed chemicals) Trauma Impact Situational awareness, gloves Foot Injury Dropped object on foot Wear safety shoes Goggles Safety Shoes/boots Gloves 8
9 Hazard Analysis: Hand Held Portable Power Tools Inhalation Dust/particles generated during machine operation Appropriate natural ventilation, disposable respirators (if necessary), automatic vacuum machine Eye Injury Projectiles Safety glasses with side shield or appropriate safety goggles Foot Injury Drop object on foot Wear safety shoes Hand Injury Point of operation, ingoing nip points, rotating parts, flying chips & sparks Machine guards, situational awareness Head Projectiles Face Shield Protection Fire Sparks Appropriate placed fire extinguisher, remove all combustibles and fire hazards from machine area Noise Machine operation Hearing protection Electrical Shock Improper grounding, improper operations and maintenance Proper grounding of frame, manufacturer s instructions strictly followed Protective Clothing (optional) Safety Shoes/Boots Goggles/Safety Glasses w/side shields Disposable Respirators (optional) Face shield, as appropriate Hearing Protection 9
10 Hazard Analysis: Heat Gun Inhalation Fumes, vapors and gases generated during use Properly ventilated work area, use disposable respirators Burns Hot air, contact with heat gun Situational awareness, gloves Electrical Shock Improper operation & maintenance Manufacturer s instructions strictly followed, replace worn parts Gloves disposable Respirators (optional, if appropriate) 10
11 Hazard Analysis: Lifting/Carrying Objects Trauma Impact Situational awareness, gloves, back brace/belt (optional) Foot Injury Dropped object on foot Wear safety shoes/boots Safety Shoes/boots Gloves Back brace/belt (optional) 11
12 Hazard Analysis: Paint Conditioner/Shaker Foot Injury Drop object on foot Safety shoes Electric Shock Improper operation and maintenance, improper grounding Manufacturer s instructions strictly followed, proper grounding Eye Injury Paint splash Goggles, face shield, apron, gloves, proper operation of shaker Hand Injury Point of Operation, rotating parts Situational awareness Apron Face Shield Gloves Goggles Safety Shoes/Boots 12
13 Hazard Analysis: Paint Stripper Inhalation Burns Electrical Shock Fumes, vapors and gases generated during use Hot surface of paint stripper, contact with paint stripper element Improper operation & maintenance Properly ventilate work area, use disposable respirators Situational awareness, gloves Manufacturer s instructions strictly followed, replace worn parts Gloves disposable Respirators (optional, if appropriate) 13
14 Hazard Analysis: Portable Generator, Gasoline Powered Inhalation Exhaust Appropriate ventilation Trauma Burns Situational awareness, PPE, protective clothing Foot Injury Roll over foot, drop object on Wear safety shoes foot Fire Heat, sparks, slag Appropriate placed fire extinguisher, remove all combustibles and fire hazards from area Electrical Shock Improper operations and maintenance, improper switching device Strictly follow manufacturer s instructions, proper switching for starting up/ shutting down machine Leather Gloves Safety Shoes/ Boots 14
15 Hazard Analysis: Portable Heater, Electric Powered Trauma Burns Situational awareness, PPE, protective clothing Foot Injury Roll over foot, drop object on Wear safety shoes foot Fire Heat, sparks, slag Appropriate placed fire extinguisher, remove all combustibles and fire hazards from area Electrical Shock Improper operations and maintenance, improper switching device Strictly follow manufacturer s instructions, proper switching for starting up/ shutting down machine Leather Gloves Safety Shoes/ Boots 15
16 Hazard Analysis: Portable Heater, Gasoline Powered Inhalation Exhaust Appropriate ventilation Trauma Burns Situational awareness, PPE, protective clothing Foot Injury Roll over foot, drop object on Wear safety shoes foot Fire Heat, sparks, slag Appropriate placed fire extinguisher, remove all combustibles and fire hazards from area Electrical Shock Improper operations and maintenance, improper switching device Strictly follow manufacturer s instructions, proper switching for starting up/ shutting down machine Leather Gloves Safety Shoes/ Boots 16
17 Hazard Analysis: Shop Vac(s) Foot Injury Drop object on foot Wear safety shoes Electrical Shock Improper operations and maintenance, improper grounding Manufacturer s instructions strictly followed, proper grounding Eye Injury Flying debris Wear safety glasses w/side shields Noise Equipment Operation hearing protection PPE Required :( PPE required to be worn during the vacuuming task when it poses a specific hazard to the user) Safety Glasses with side shields Hearing Protection Safety Shoes/Boots 17
18 Hazard Analysis: Vise Eye Injury Projectiles Safety glasses with side shield or appropriate safety goggles Foot Injury Drop object on foot Wear safety shoes Hand Injury Impact, penetration, compression Gloves, situational awareness Goggles/ Safety Glasses w/ side shield Gloves Safety Shoes/Boots 18
Job Hazard/Safety Analysis For the Lab Worker
Job Hazard/Safety Analysis For the Lab Worker 1 INTRODUCTION Job Hazard/Safety Analysis for the Lab Worker is a partial list of known task performed by the professional laboratory worker. We have placed
Job Hazard/Safety Analysis For the Building Maintenance Worker
Job Hazard/Safety Analysis For the Building Maintenance Worker 1 INTRODUCTION Job Hazard/Safety Analysis for the Building Maintenance Worker is a partial list of known task performed by the professional
Job Hazard/Safety Analysis For the Housekeeper
Job Hazard/Safety Analysis For the Housekeeper 1 INTRODUCTION Job Hazard/Safety Analysis for the Housekeeper is a partial list of known task performed by the professional housekeeper. We have placed task
Job Hazard/Safety Analysis For the Grounds Keeper
Job Hazard/Safety Analysis For the Grounds Keeper 1 INTRODUCTION Job Hazard/Safety Analysis for the Grounds Keeper is a partial list of known task performed by the professional grounds worker. We have
Job Hazard/Safety Analysis For the Plumber
Job Hazard/Safety Analysis For the Plumber 1 INTRODUCTION Job Hazard/Safety Analysis for the Plumber is a partial list of known task performed by the professional plumber. We have placed the tasks in alphabetical
Job Hazard Analysis Manual. Updated 10/6/04
Job Hazard Analysis Manual Updated 10/6/04 Abrasive Cutoff Saw General Use Inhalation Dust/particles generated during machine operation Appropriate natural ventilation, disposable respirators, automatic
Job Hazard/Safety Analysis For the Office Worker
Job Hazard/Safety Analysis For the Office Worker 1 INTRODUCTION Job Hazard/Safety Analysis for the Office Worker is a partial list of known task performed by the professional office worker. We have placed
Tech Shop Safety Level 2 - FN000425. Tech Shop / Tool Safety Operations. (Fermilab machines not covered in course FN000258)
Tech Shop Safety Level 2 - FN000425 Tech Shop / Tool Safety Operations (Fermilab machines not covered in course FN000258) Table of Contents Tech Shop / Tool Safety Operations 3 General Rules of Safety
GEORGIA INSTITUTE OF TECHNOLOGY ENVIRONMENTAL HEALTH AND SAFETY PERSONAL PROTECTIVE EQUIPMENT
PURPOSE To protect the health and welfare of GEORGIA TECH employees in areas where there may be a risk of injury or exposure to hazardous substances or conditions employees who work in areas where physical
SAFETY in the work area is a broad topic because of the
A Safe Place to Work SAFETY in the work area is a broad topic because of the many components of agricultural mechanics. Safety is protection from injury or loss. Injury can result from improper use of
Master Workplace Inspection Checklist for General Shop Safety. MASTER WORKPLACE INSPECTION CHECKLIST General Shop Safety
Integrated Risk Management Master Workplace Inspection Checklist for General Shop Safety Document Type: Form Control Number: UIRM- FM_012_50 File Code: UIRM-001 Last Reviewed: March 2014 Department/Unit:
Curtain Guards Made of PVC and designed to protect the operator from the risk of airborne chips or tool fragments.
Two General Safety Rule for CNC Machines Never operate a CNC machine without proper training or consulting the specific operator's manual for that particular machine and control type. Never attempt to
Notes. Material 1. Personal Protective Equipment 2.
29CFR 1926.20(b)-Accident Reduction, 29CFR 1926.21- Safety Training & Education 29CFR 1926.20(a)-Unsafe Working Conditions 29 CFR 1910.132-138, the "Personal Protection Equipment" standard. & 20 CFR 1910.134
PALM BEACH STATE COLLEGE PERSONAL PROTECTIVE EQUIPMENT (PPE) JOB HAZARD ASSESSMENT
PALM BEACH STATE COLLEGE PERSONAL PROTECTIVE EQUIPMENT (PPE) JOB HAZARD ASSESSMENT Department: Facilities Campus: All Task: Check/Service/Maintain/Repair/Install HVAC Equipment and Systems Job Title(s)
Additional information: -OSHA Instruction CPL 2.103, Field Inspection Reference Manual, Chapter IV, Section A -29 CFR 1910, Subpart I, Appendix B
1 Additional information: -OSHA Instruction CPL 2.103, Field Inspection Reference Manual, Chapter IV, Section A -29 CFR 1910, Subpart I, Appendix B -1910.1000(e) 2 1910.132(h) 72 FR 64341, Nov. 15, 2007
PERSONAL PROTECTIVE EQUIPMENT FOR CALIFORNIA STATE UNIVERSITY, LOS ANGELES
PERSONAL PROTECTIVE EQUIPMENT FOR CALIFORNIA STATE UNIVERSITY, LOS ANGELES OCTOBER 2007 PROGRAM APPROVAL AND AUTHORIZATION James M. Rosser, President Date TABLE OF CONTENTS TITLE Section PURPOSE...1.0
Personal Protective Equipment Policy & Procedure Date: August, 2001 Approved by:
OCCUPATIONAL SAFETY AND HEALTH POLICY Topic: Personal Protective Equipment Policy & Procedure Date: August, 2001 Approved by: Author(s): Distribution: Cindy Davis, Risk Management; Ed Polluconi, EH&S;
Dining Services OSHA Safety Training Program TRAINING RECORD
Dining Services OSHA Safety Training Program TRAINING RECORD Employee Title: This record documents the safety training received by Dining Services employees, including student employees, as required by
WEEKLY SAFETY MEETING All Euramax Subsidiaries WELDING SAFETY / HOT WORK SAFETY. Safety Meeting Contents. Meeting Notice.
Safety Meeting Contents Meeting Notice Leaders Guide Employee Handout Employee Quiz Meeting Sign-In Sheet Employee Puzzle PRIOR TO THE WEEKLY MEETING: - Post the meeting notice by the timeclock - Read
Safety Training Topic PERSONAL PROTECTIVE EQUIPMENT
Safety Training Topic PERSONAL PROTECTIVE EQUIPMENT Purpose of Meeting To remind workers that using personal protective equipment (PPE) can protect them from serious injury. To reince PPE safety rules.
Abrasive Wheel Grinder Safety
Abrasive Wheel Grinder Safety One of the most common pieces of machinery in use in the maintenance shops on campus is the abrasive wheel grinder. These useful machines, used to remove metal from flat and
Respiratory Safety and PPE Module 7. Special Warehouse Worker Hazards in Structural Steel Fabricating and Supply Companies
Respiratory Safety and PPE Special Warehouse Worker Hazards in Structural Steel Fabricating and Supply Companies Drawing from OSHA 3384-09 2011 1 Respiratory Safety and PPE OSHA Grant Information This
How to Reduce Your Exposure to Chemicals at Home, Work, and Play
How to Reduce Your Exposure to Chemicals at Home, Work, and Play You come into contact with chemicals every day. This is called chemical exposure. Although some chemical exposures are safe, others are
Installation Instructions for Alarm Module Kit A043F059
Instruction Sheet 07-2013 Installation Instructions for Alarm Module Kit A043F059 1 Introduction The information contained within is based on information available at the time of going to print. In line
Conducting a Job Hazard Assessment. Environmental, Health and Safety 275-3241
Conducting a Job Hazard Assessment Environmental, Health and Safety 275-3241 EH&S Programs: Fire Safety Blood Borne Pathogens Hazard Communication Personal Protective Equipment Emergency Preparedness General
Machine/Woodworking Shop The Basic Rules
Machine/Woodworking Shop The Basic Rules 1. Eye protection or face shields are required when working in the shop. A selection of protective goggles and safety glasses are available in the shop. The eyeglasses
ALVERNIA UNIVERSITY OSHA REGULATION: 29 CFR 1910.252 WELDING, CUTTING, AND BRAZING ( HOT WORK ) SECTION: 3600
OSHA REGULATION: 9 CFR 90.5 WELDING, CUTTING, AND BRAZING ( HOT WORK ) A. POLICY. This procedure follows requirements set forth in 9 CFR 90.5.. This policy applies to all Hot Work operations being done
Welcome to the safe@work Automotive Module.
Welcome to the safe@work Automotive Module. Have you read the General Module, completed the test and gained your safe@work General certificate? The Automotive Module should be done AFTER the General Module
Technical Data Sheet
Februar, 2014 Technical Data Sheet PLA Polylactide Cas No. 9051-89-2 PLA is a thermoplastic resin derived from annually renewable resources Product Characteristics Typical Properties Value Unit Physical
If you have any questions about how to safely undertake a task or project, ask your supervisor before you begin.
Laboratory Health and Safety Manual Section 1: Introduction and Objectives This manual provides a set of minimum standards and practices for the safe and healthy operation of a laboratory. Following the
240-3118 AIR CUT OFF KIT INSTALLATION INSTRUCTIONS
OPERATION MANUAL GLOBAL ELECTRONIC MIX SOLUTIONS PLURAL COMPONT MIXING SYSTEM 240-3118 AIR CUT OFF KIT INSTALLATION INSTRUCTIONS 77-3087-R1.0 (8/2015) 1 / 5 In this part sheet, the words WARNING, CAUTION
Environment. Personal Protective Equipment Requirements for Photographic Processing Facilities. Kodak s health, safety, and environmental
Environment I N F O R M A T I O N F R O M K O D A K Personal Protective Equipment Requirements for Photographic Processing Facilities J-312 $10.00 Kodak s health, safety, and environmental Protecting employees
Standard Operating Procedure
Standard Operating Procedure FLAMMABLE LIQUIDS This standard operating procedure (SOP) is intended to provide general guidance on how to safely work with flammable liquids. This SOP is generic in nature
Chemical Spill Response Guideline
ChemicalSpillResponseGuideline Despite the best efforts of researchers to practice safe science in the laboratory, accidents resulting in the release of chemicals will occur. For this reason, it is essential
University of Glasgow School of Engineering UGRacing Formula Student Garage
University of Glasgow School of Engineering UGRacing Formula Student Garage James Watt South Building Level 4 CODE OF PRACTICE Emergency telephone number is 4444 Fire extinguishers located next to emergency
TEMPORARY EMPLOYEES SAFETY PROCEDURES
TEMPORARY EMPLOYEES SAFETY PROCEDURES Temporary Agencies will ensure that any temporary employee sent to work at Modern will have received and understand the General Safety Rules. GENERAL SAFETY RULES
Notes. Material 1. Tools the employee is expected to operate
OSHA Standard29 CFR 1910.211-.247, Subpart O, Machinery and Machine Guarding, and Subpart P, Hand and Portable-Powered Tools and other Hand- Held Equipment. Hand Tool Safety Preparation 1. Read Applicable
Presented by: Rich Perry Marsh Risk Consulting
Flammable and Combustible Liquids Presented by: Rich Perry Marsh Risk Consulting What s the Big Deal? Flammable and combustible liquids are easily ignited Ignite with explosive force Burn readily and give
A SELF-EVALUATION CHECKLIST of BEST PRACTICES for AUTO REFINISH SHOPS and SCHOOLS
A of BEST PRACTICES for AUTO REFINISH SHOPS and SCHOOLS www.epa.gov/dfe/pubs/projects/auto/ WHAT IS THE DESIGN FOR THE ENVIRONMENT (DFE) AUTO REFINISH PROJECT? The DfE Program has been working with the
Course Title: Safety Issues in Electronics Engineering Technology Number of Credits: 3 B.A. B.S. B.A.S A.A. A.S. Degree Type
GENERAL INFORMATION Name: Diane King Phone #: 77021 Course Prefix/Number: ETI3704 Course Title: Safety Issues in Electronics Engineering Technology Number of Credits: 3 B.A. B.S. B.A.S A.A. A.S. Degree
PERSONAL PROTECTIVE EQUIPMENT (PPE)
Page 1 of 6 (PPE) Personal protective equipment (PPE) is used to protect an individual from hazards associated with their work tasks or environment. Specific types of personal protective equipment include
Safety and Health Policy and Procedure Manual. PERSONAL PROTECTIVE EQUIPMENT Section 0130. Table of Contents
Safety and Health Policy and Procedure Manual PERSONAL PROTECTIVE EQUIPMENT Section 0130 Table of Contents I. INTRODUCTION II. STANDARDS III. SCOPE IV. PURPOSE V. GENERAL REQUIREMENTS VI. EMPLOYEE OWNED
Compressed Gas Cylinder Storage and Handling Guide
Overview Compressed gas cylinders are used in many workplaces to store gases that vary from extremely flammable (acetylene) to extremely inert (helium). Many compressed gas cylinders are stored at extremely
Fire Safety in Laboratories. University of Tennessee Environmental Health and Safety
Fire Safety in Laboratories University of Tennessee Environmental Health and Safety Fire Safety in Laboratories Fire Prevention is a vital aspect of laboratory safety. Requires knowledge and constant vigilance
ACCIDENT PREVENTION IN THE QUARRY INDUSTRY IN SA July 2011
ACCIDENT PREVENTION IN THE QUARRY INDUSTRY IN SA July 2011 Introduction Accident prevention requires the creation and maintenance of a safe working environment, and the promotion of safe behaviour. Accident
PERSONAL PROTECTIVE EQUIPMENT HAZARD ASSESSMENT, EQUIPMENT SELECTION AND TRAINING DOCUMENTATION
DRAFT SAMPLE WRITTEN PERSONAL PROTECTIVE EQUIPMENT HAZARD ASSESSMENT, EQUIPMENT SELECTION AND TRAINING DOCUMENTATION For Compliance With 1910.132 Wyoming General Rules and Regulations Wyoming Department
RESPIRATORY PROTECTION PROGRAM
RESPIRATORY PROTECTION PROGRAM OFFICE of ENVIRONMENTAL HEALTH & SAFETY Campus Location: Physical Plant 521 S. Razorback Road Telephone: 479 575 5448 Web site: http://www.phpl.uark.edu Applies to all UofA
MATERIAL SAFETY DATA SHEET DATE: 2009, revised July 2011 PRODUCT NAME: BOSTON BRAKE & PARTS CLEANER PRODUCT CODE: 78200
MATERIAL SAFETY DATA SHEET DATE: 2009, revised July 2011 PRODUCT NAME: BOSTON BRAKE & PARTS CLEANER PRODUCT CODE: 78200 SUPPLIER S NAME : SECTION I SUPPLIER IDENTIFICATION CAMPBELLS WHOLESALE PTY LTD ADDRESS
Reducing Roofers Exposure to Asphalt Fumes
Reducing Roofers Exposure to Asphalt Fumes Department of Health and Human Services Centers for Disease Control and Prevention National Institute for Occupational Safety and Health Reducing Roofers Exposure
Personal Protective Equipment Guidelines
Personal Protective Equipment Guidelines Purpose To establish guidelines for use and care of personal protective equipment, which is to be used by employees and /or students when a hazard is found to exist
SAFETY DATA SHEET 安 全 数 据 单
SAFETY DATA SHEET 安 全 数 据 单 1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE COMPANY/UNDERTAKING PRODUCT NAME: InnoPlus LDPE 2420D CHEMICAL NAME: Low Density Polyethylene MANUFACTURER: 14 Map
Date: 22 June 2005 Version: 2 Revision: 1. 1. Identification of the substance/preparation and company/undertaking
Page 1 of 5 1. Identification of the substance/preparation and company/undertaking Product identifier Use Details of supplier of the safety data sheet Engine oil Telephone number +44-20-7186-0400 FAX number
NFPA Hazard Class: * Physical Form: Solid. Health: 0 (Least) * Appearance: Yellow Flammability: 1 (Slight)
Safety Data Sheet Microcrystalline Wax 1. Chemical Product Identification Generic Name: Microcrystalline Wax INCI Name: Microcrystalline Wax Chemical Family: Mineral Emergency Telephone Numbers: Page 1
Ultrasonic support removal tank
Ultrasonic support removal tank User guide and safety manual See inside for use and safety information. The Ultrasonic support removal tank automatically removes PLA support material from a printed ABS
Example risk assessment for a motor vehicle mechanical repair workshop
Example risk assessment for a motor vehicle mechanical repair workshop Setting the scene The garage manager did the risk assessment. The business employed 12 mechanics, including two apprentices who carried
Student Shop Safety Policy GS92 Page 1
Policy Subject: Student Shop Safety Effective: 8/1/2012 Affected Area: Machine Shops on Campus Reviewed/Revised: 8/1/2012 1.0 Purpose, Applicability, and Scope 1.1 Purpose- This policy identifies the requirements
SOLVENT CLEANER MSDS Page 1 of 5 SAFETY DATA SHEET. (To comply with OSHA s Hazard Communication Standard 29CFR 1910.1200/ANSI z400.
SOLVENT CLEANER MSDS Page 1 of 5 SAFETY DATA SHEET (To comply with OSHA s Hazard Communication Standard 29CFR 1910.1200/ANSI z400.1-1993) 1. PRODUCT & COMPANY IDENTIFICATION Prepared on: Month, Year Manufactured
15GAL STEEL OIL DRAIN WITH 110V PUMP
15GAL STEEL OIL DRAIN WITH 110V PUMP OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety
National- Spencer Inc.
9-27-2010 National- Spencer Inc. 19.2V HEAVY DUTY GREASE GUN PRODUCT SPECIFICATION Charger Input Power 110 VAC Battery Output Power 19.2V Battery Capacity 1500 MAH Battery Pack Charge Time 1 Hour Maximum
Document the assessment, PPE selection, and training.
Requirements... 1 Hazard Control... 1 Supervisor Responsibilities... 2 How to Use This Website... 3 Step One - Assessment... 3 Step Two - Selection... 3 Step Three - Training... 4 Step Four - Documentation...
"ACCIDENT PREVENTION AND SAFETY HOUSEKEEPING"
MAJOR PROGRAM POINTS "ACCIDENT PREVENTION AND SAFETY HOUSEKEEPING" Part of the "GENERAL SAFETY SERIES" Quality Safety and Health Products, for Today...and Tomorrow Outline of Major Points Covered in the
IMPORTANT SAFETY NOTICE
IMPORTANT SAFETY NOTICE To: Our Valued Customers User safety is a major focus in the design of our products. Following the precautions outlined in this manual will minimize your risk of injury. ITT Goulds
Lockout - Tagout. Control of Hazardous Energy OSHA Standard 1910.147
Lockout - Tagout Control of Hazardous Energy OSHA Standard 1910.147 You will learn Purpose of Lockout-Tagout Requirements for LOTO Types of Hazardous Energy Procedures for LOTO Types of Energy Electrical
School of Engineering University of Glasgow
School of Engineering University of Glasgow Electronics Workshops Rankine Building 319A (2 Technicians) 510 (1 Technician) 712A (4 Technicians, 1 Modern Apprentice) James Watt South 619 (2 Technicians)
Industrial Process Pump Safety Manual IMPORTANT SAFETY NOTICE
Industrial Process Pump Safety Manual IMPORTANT SAFETY NOTICE To: Our Valued Customers User safety is a major focus in the design of our products. Following the precautions outlined in this manual will
Chemical Reducing Solution CRS
Chemical Reducing Solution CRS Material Safety Data Sheet (MSDS) Revised: August 21, 2012 Supplier: Section 1 Supplier Information and Material Identification 1011 Calle Sombra San Clemente, CA 92673 Telephone:
Hazard/Risk Identification and Control Procedure
Hazard/Risk Identification and Control Procedure Introduction Hazard identification and the steps taken to minimize the risks associated with identified hazards are a critical component of working safely.
Safety Data Sheet for Whole Grain
SECTION 1: IDENTIFICATION Safety Data Sheet for Whole Grain PRODUCT NAME: SDS NUMBER: WHOLE GRAIN GRAIN SYNONYMS/OTHER MEANS OF IDENTIFICATION: INTENDED USE: FOOD MANUFACTURER: (company name) EMERGENCY
Safe Cleanup of Fire Ash
Safe Cleanup of Fire Ash The recent fires have deposited large amounts of ash on indoor and outdoor surfaces in areas near the fire. Questions have been raised about possible dangers from contact with
Pressure Vessels (Air Compressors) and LPG Tanks
Pressure Vessels (Air Compressors) and LPG Tanks 1. Identification of Workplace Hazard Any container, tank or vessel that contains pressurized material is a potential hazard to employees due to the force
CHEMICAL SPILL RESPONSE GUIDE
HEMIAL SPILL RESPONSE GUIDE Revised 2000 TABLE OF ONTENTS Emergency Phone Numbers Introduction - hemical Spill Response Spill Response Procedures - Major Spill Spill Response Procedures - Minor Spill Spills
Safety Data Sheet Customwood MDF
1. IDENTIFICATION OF THE MATERIAL AND SUPPLIER. Product Details Product Name: Other Names: Manufacturer s code: U.N. Number: Dangerous Goods Class: HAZCHEM Code: Toxic Substances Schedule: Uses: Customwood
Occupational Hazards for Health Care Workers. Photos from Occupational Safety and Health Administration, USA
Occupational Hazards for Health Care Workers Photos from Occupational Safety and Health Administration, USA Who is a Health Care Worker? Nurse Doctor Aide, orderly Pharmacist Laundry worker Housekeeper
120Volt 60-70A ARC WELDER. 80000 Rev 80000-20080214
80000 Rev 80000-20080214 10006 Santa Fe Springs Road Santa Fe Springs, CA 90670 USA Made in China Owner s Manual and Operating Instructions 120Volt 60-70A ARC WELDER Table of Contents Introduction...
Material Safety Data Sheet
1. Product & Company Identification: Product: Conrad Energy Kamera-Akku Manufacturer: Conrad Electronic SE Nominal capacity: 1500 mah Nominal voltage: 7,4 V Address: Klaus-Conrad-Strasse 1, D-92240 Hirschau
Personal protective equipment (PPE) at work A brief guide
Personal protective equipment (PPE) at work A brief guide Introduction This leaflet describes what you, as an employer, may need to do to protect your employees from the risk of injury in the workplace.
Occupational Health Program Safety Training Series. Lockout/Tagout Safety Awareness Training
Occupational Health Program Safety Training Series Lockout/Tagout Safety Awareness Training 1 Lock out/tag out Lock out: the placement of a lockout device (lock) on an energy isolating device in accordance
Lead Monitoring / Removal
Lead Monitoring / Removal 1.0. INTRODUCTION The Occupational Safety and Health Administration (OSHA) adopted standards which regulate occupational exposures to lead in general industries. Since that time,
Department of Environmental Health and Safety & Emergency Management
Date: February 2014 Revision: 02 Page: 1 of 13 This Guideline is issued jointly by the Department of Environmental Health and Safety & (EHSEM) and Facilities Management to provide guidance and consistency
Lead Exposure Management Plan
Lead Exposure Management Plan 1.0. Policy CSUF has developed the Lead Exposure Management Plan to reduce occupational and environmental exposure to lead, a potent neurotoxin and carcinogen that causes
Chemotherapy Spill Response:
Chemotherapy Spill Response: Antineoplastic Spills Outside Of A Fume Hood Lisa Hudley, RN Training Coordinator Safety & Environmental Compliance William Guess Director Safety & Environmental Compliance
MODEL T-4 TRENCHER. Operators Manual
DO NOT THROW AWAY IMPORTANT MANUAL MODEL TRENCHER Operators Manual P.O.BOX 290 San Bernardino, CA. 92402 Phone (909) 478-5700 (800) 922-4680 Fax (909) 478-5710 E-mail: sales@groundhoginc.com www.groundhoginc.com
PLASMA CUTTER - 35 AMP
PLASMA CUTTER - 35 AMP 45949 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright 2003 by Harbor Freight Tools.
University of Tennessee Safety Program
University of Tennessee Safety Program Program Subject: Lead Management Program Reviewed/Revised: 4/1/14 Areas Affected: All pre-1978 buildings on campus and other areas where lead is present Contact Information:
PPE hazard assessment
Oregon OSHA s quick guide to the PPE hazard assessment What you should know and not a word more! A Division of the Department of Consumer and Business Services About this guide Oregon OSHA quick guides
Laboratory Safety Guideline Electrical Safety
Introduction The typical laboratory contains a wide variety of electrically-powered equipment including stirrers, shakers, pumps, hot plates, heaters, power supplies, ovens, and electrophoresis equipment.
Material Safety Data Sheet
Material Safety Data Sheet Ethyl Red MSDS 1 2 0 Section 1: Chemical Product and Company Identification He a lt h Fire Re a c t iv it y Pe rs o n a l Pro t e c t io n 2 1 0 E Product Name: Ethyl Red Catalog
PERSONAL PROTECTIVE EQUIPMENT POLICY & GUIDANCE
Health and Safety Policy PERSONAL PROTECTIVE EQUIPMENT POLICY & GUIDANCE ROYAL FREE HOSPITAL NHS TRUST & SCHOOL OF MEDICINE CONTENTS 1. SUMMARY OF THE REGULATIONS 2. INTRODUCTION 3. DEFINITION OF PERSONAL
Oxy-Fuel Gas Welding. Given a functional oxy-fuel gas unit, instruction and demonstration of use, each student will be able to:
I. Competencies Oxy-Fuel Gas Welding Given a functional oxy-fuel gas unit, instruction and demonstration of use, each student will be able to: A. Identify the major parts of the oxy-fuel gas unit. B. Pass
Employee Safety Handbook
i Table of Contents I. Introduction Background.................. 1 Health and Safety Policy.................. 1 Health and Safety Responsibilities................. 1 Employees Responsibilities..................
Material Safety Data Sheet
Date of Issue: 26/5/2009 MSDS No.: Q54-1300B Material Safety Data Sheet 1. PRODUCT AND COMPANY IDENTIFICATION Product Name : Daily Maintenance Kit(Wipe Cleaning) Product Code : IP6-108 -Application model
Risk Management Program March 2015
AS/NZS 4801 OHSAS 18001 OHS20309 SAI Global Risk Management Program March 2015 Introduction Monash University s Victorian campuses are all governed by the Victorian OHS Act 2004 and its subordinate regulations
Portable Grinder. Given a properly adjusted portable grinder, instruction and demonstration of use, each student will be able to:
Portable Grinder I. Competencies Given a properly adjusted portable grinder, instruction and demonstration of use, each student will be able to: A. Identify the major parts of the portable grinder. B.
PERSONAL PROTECTIVE EQUIPMENT PROGRAM
Sample Written Program For PERSONAL PROTECTIVE EQUIPMENT PROGRAM 1 TABLE OF CONTENTS Development... 3 Hazard Assessment........3 Choosing Personal Protective Equipment.......4 Training.......4 Conclusion...4
1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE COMPANY/UNDERTAKING.
1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE COMPANY/UNDERTAKING. 1.1 Identification of the substance or preparation: This safety data sheet covers all recycled grades of polyethylene (PE)
Texas Department of Insurance. Provided by. Personal Protective Equipment. Division of Workers' Compensation HS96-101C (10-06)
Texas Department of Insurance Personal Protective Equipment Provided by Division of Workers' Compensation HS96-101C (10-06) PERSONAL PROTECTIVE EQUIPMENT PROGRAM TABLE OF CONTENTS Development...3 Hazard
LOS ANGELES UNIFIED SCHOOL DISTRICT DIVISION OF ADULT AND CAREER EDUCATION SAFETY TEST FOR ELECTRICIAN PROGRAM
LOS ANGELES UNIFIED SCHOOL DISTRICT DIVISION OF ADULT AND CAREER EDUCATION SAFETY TEST FOR ELECTRICIAN PROGRAM Service Area: Industry Sector: Energy, Environment & Utilities Class Teacher (Please Print)
Welcome to the safe@work Hairdressing Module
Welcome to the safe@work Hairdressing Module Have you read the General Module, completed the test and printed your safe@work General Award of Attainment? The Hairdressing Module should be done AFTER the
Safety Training Needs Assessment
Safety Needs Assessment Form Instructions: Please review each question and either check YES or NO. If a question is checked YES you will be required to complete the training topic before initial assignment
car + boat Box Contents x2 x2 22350_DC16_CAR_BOAT_OPSMAN.indd 1 29/7/08 15:27:01
car + boat Box Contents x x 350_DC6_CAR_BOAT_OPSMAN.indd 9/7/08 5:7:0 SAVE THESE INSTRUCTIONS THIS APPLIANCE IS INTENDED FOR HOUSEHOLD USE ONLY IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE