TL-WA701ND 150Mbps Wireless Lite N Access Point

Size: px
Start display at page:

Download "TL-WA701ND 150Mbps Wireless Lite N Access Point"

Transcription

1 150Mbps Wireless Lite N Access Point Rev:

2 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright 2009 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved.

3 FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment. Such modifications could void the user s authority to operate the equipment. FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

4 National restrictions This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below: Country Restriction Reason/remark Bulgaria France None Outdoor use limited to 10 mw e.i.r.p. within the band MHz General authorization required for outdoor use and public service Military Radiolocation use. Refarming of the 2.4 GHz band has been ongoing in recent years to allow current relaxed regulation. Full implementation planned 2012 Italy Luxembourg Norway None None Implemented If used outside of own premises, general authorization is required General authorization required for network and service supply(not for spectrum) This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Ålesund Russian Federation None Only for indoor applications Note: Please don t use the product outdoors in France.

5 TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: 150Mbps Wireless Lite N Access Point Model No.: TL-WA701ND Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives: Directives 1999/5/EC The above product is in conformity with the following standards or other normative documents ETSI EN V1.7.1: 2006 ETSI EN V1.8.1:2008& ETSI EN V1.3.2:2008 EN :2006 EN :1995+A1:2001+A2:2005 EN :2006 Recommendation 1999/519/EC EN62311:2008 Directives 2004/108/EC The above product is in conformity with the following standards or other normative documents EN 55022:2006 +A1:2007 EN 55024:1998+A1:2001+A2:2003 EN :2006 EN :1995+A1:2001+A2:2005 Directives 2006/95/EC The above product is in conformity with the following standards or other normative documents EN :2006 Person is responsible for marking this declaration: Yang Hongliang Product Manager of International Business TP-LINK TECHNOLOGIES CO., LTD. South Building, No.5 Keyuan Road, Central Zone, Science & Technology Park, Nanshan, Shenzhen, P. R. China

6 CONTENTS Package Contents... 1 Conventions... 1 Overview of This Guide... 2 Chapter 1 Introduction Product Overview Main Features Appearance The Front Panel The Rear Panel...6 Chapter 2 Hardware Installation Before You Begin Basic Requirements Connecting the Device... 7 Chapter 3 Configure the PC... 9 Chapter 4 Configure the Device Login Status QSS Network Wireless Wireless Settings Wireless Security Wireless MAC Filtering Wireless Advanced Throughput Monitor Wireless Statistics DHCP DHCP Settings DHCP Clients List Address Reservation System Tools SNMP Diagnostic Firmware Upgrade Factory Defaults...57

7 4.7.5 Backup & Restore Ping Watch Dog Reboot Password System Log...60 Appendix A: Application Example Appendix B: Factory Defaults Appendix C: Troubleshooting Appendix D: Specifications Appendix E: Glossary... 68

8 Package Contents TL-WA701ND 150Mbps Wireless Lite N Access Point Resource CD, including: This User Guide Other Helpful Information Power Adapter for TL-WA701ND 150Mbps Wireless Lite N Access Point Power Injectors Ethernet Cables Quick Installation Guide PoE Guide Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact with your distributor. Conventions The AP or TL-WA701ND, or device mentioned in this User guide stands for TL-WA701ND 150Mbps Wireless Lite N Access Point without any explanations. Parameters provided in the pictures are just references for setting up the product, which may differ from the actual situation. You can set the parameters according to your demand. 1

9 Overview of This Guide Package Contents: Chapter 1 Introduction: Tells what are contained in the box. Gives an introduction for the TL-WA701ND 150Mbps Wireless Lite N Access Point. 1.1 Product Overview: Introduces advantages of using this AP. 1.2 Main Feature: Introduces main features and their benefits. 1.3 Appearance: Gives descriptions of LEDs, ports and buttons on the front and rear panel. Chapter 2 Hardware Installation: Tells how to connect the AP and the requirements. 2.1 Before You Begin: Gives suggestions for better performance of the wireless network. 2.2 Basic Requirement: Introduces some basic requirements for successful installation and long-term use 2.3 Connecting the Device: Introduces steps to connect the AP. Chapter 3 Configure the PC: Chapter 4 Configure the Device: Tells how to configure the IP address of your PC in order to access the AP. Tells how to configure the AP via the web-based management page. 4.1 Login: Tells how to log on to the web-based management page. 4.2 Status: Gives information about the AP s current configuration. 4.3 QSS Guides how to add a new wireless device to an existing network quickly. 4.4 Network: Tells how to configure the IP parameters of AP. 4.5 Wireless: Guides to establish the wireless network in different wireless modes and deploy the security features appropriate to your needs. 4.6 DHCP: Introduces how to set your AP to be a DHCP server so that the AP will automatically assign an IP address for your PC. 4.7 System Tools: Provides some useful tools. 2

10 Chapter 1 Introduction Thank you for choosing the TL-WA701ND 150Mbps Wireless Lite N Access Point. 1.1 Product Overview The TL-WA701ND 150Mbps Wireless Lite N Access Point is dedicated to Small Office/Home Office (SOHO) wireless network solutions. It allows for greater range and mobility within your wireless network while also allowing you to connect the wireless devices to a wired environment. Increased mobility and the absence of cabling will be beneficial for your network. With using IEEE n wireless technology, your device can transmit wireless data at the rate of up to 150Mbps. With multiple protection measures, including SSID broadcast control and wireless LAN 64/128/152-bit WEP encryption, WiFi protected Access (WPA2- PSK, WPA- PSK), as well as advanced Firewall protections, the TL-WA701ND 150Mbps Wireless Lite N Access Point delivers complete data privacy. It supports an easy, web-based setup for installation and management. Even though you may not be familiar with the Access Point, you can easily configure it with the help of this Guide. Before installing the AP, please look through this Guide to get the full information of the TL-WA701ND 150Mbps Wireless Lite N Access Point. 3

11 1.2 Main Features Features Make use of IEEE n wireless technology Provides multiple encryption security Types including: 64/128/152-bit WEP WPA/WPA2 WPA-PSK/WPA2-PSK Supports Built-in DHCP server Supports MAC address filtering Supports multiple operating modes including: Access Point Benefits Allows your device to transmit wireless data at the rate of up to 150Mbps Secures your data while the data packets are being transmitted Supports dynamic IP address distributing Allows you to control the access rights of the wireless stations, depending on the stations' MAC addresses Makes the AP an ideal solution for your wireless local area network You can create a wireless local area network Multi-SSID Allows the wireless adapter to access to different LANs appropriate to your needs by connecting to different SSID Client Wirelessly connects Ethernet devices Repeater(Universal Repeater) Relays signal between its stations and the root AP for greater wireless range Bridge (Point to Point, Point to Multi-point) Bridges the AP and another AP also in bridge mode to connect two or more wired LANs Supports Firmware Upgrade Supports Remote and Web management You can easily upgrade the firmware to the latest version through the web-based management page Allows you to manage your wireless LAN easily through the web-based management page, while the management by remote computer is also available 4

12 1.3 Appearance The Front Panel Figure 1-1 The front panel of the TL-WA701ND consists of several LED indicators, which is designed to indicate connections. View from left to right, Table 1-1 describes the LEDs on the front panel of the device. LED Explanation Name Status Indication Power System LAN WLAN Off On Off On Flashing Off On Flashing Off Flashing No Power Power on The device has a system error The device is initialising The device is working properly There is no device linked to the corresponding port There is a device linked to the corresponding port but no activity There is an active device linked to the corresponding port The Wireless function is disabled The Wireless function is enabled QSS Slow Flash On A wireless device is connecting to the network by QSS function. This process will last in the first 2 minutes. A wireless device has been successfully added to the network by QSS function. Quick Flash A wireless device failed to be added to the network by QSS function. Table 1-1 5

13 1.3.2 The Rear Panel Figure 1-2 Viewed from left to right, the following parts are located on the rear panel of TL-WA701ND. POWER: The power port connects to the power adapter provided with the TL-WA701ND 150Mbps Wireless Lite N Access Point. LAN: One LAN 10/100Mbps RJ45 port connects to a network device, such as a switch or a router. RESET: The Reset button is used to restore the AP s factory default settings. There are two ways to reset the Access Point s factory defaults: Method one: With the AP powered on, use a pin to press and hold the Reset button (about 5 seconds) until the System LED becomes quick-flash from slow-flash. And then release the button and wait the router to reboot to its factory default settings. Method two: Restore the default settings from System Tools > Factory Defaults of the Modem's Web-based management page. Wireless antenna: The external antenna is used to transmit and receive wireless data. Ensure the AP is powered on before it restarts completely. 6

14 Chapter 2 Hardware Installation 2.1 Before You Begin Please read this User Guide carefully before installing and using the equipment. The operating distance range of your wireless connection can vary significantly depending on the physical position of the wireless devices. Factors that can weaken signals by getting in the way of your network s radio waves are metal appliances or obstructions, and walls. Typical ranges vary base on the types of materials and background RF (radio frequency) noise in your home or office. For best performance of your wireless network, you are suggested to: 1). Avoid redundant obstacles and interference between the wireless devices. 2). Keep your AP away from appliances with a strong electric field or magnetic field, such as a microwave oven or refrigerator. Place the AP near the center of the area in which your computers operates. 2.2 Basic Requirements Use only the power adapter provided with your AP The electrical outlet shall be installed near the device and shall be easily accessible Place your AP in a well ventilated place far from direct sunlight, any heater or heating vent Leave at least 2 inches (5cm) space around the device for heat dissipation Turn off your AP and unplug the power adapter in a lighting storm to avoid damage Web browser, such as Microsoft Internet Explorer 5.0 or above, Netscape Navigator 6.0 or above Operating temperature: 0 ~40 (32 ~104 ) Operating Humidity: 10%~90%RH, Non-condensing 2.3 Connecting the Device Figure 2-1 is an example of the typical application of TL-WA701ND in the infrastructure network. An Infrastructure network contains an access point or a wireless router. 7

15 Figure 2-1 The Example of Infrastructure Network Incorporating the TL-WA701ND To establish a typical connection of the AP, please take the following steps: 1. Connect the Cable or DSL modem to a Router. 2. Locate an optimum location for the AP. The best place is usually near the center of the area in which your PC(s) will wirelessly connect. 3. Adjust the direction of the antenna. Normally, upright is a good direction. 4. Connect the Ethernet Broadband Router to the TL-WA701ND Access Point. Power on the AP. 5. Then you can connect a desktop PC or laptop to your network. (Make sure your computer or laptop is equipped with a Wireless Adapter.) If you are not so clear about how to connect your devices to the network, please refer to Appendix A Application Example. 8

16 Chapter 3 Configure the PC This chapter will guide you to configure your PC to communicate with the AP. The wireless adapter-equipped computers in your network must be in the same IP Address range without overlap with each other. Manually configure the IP address as * (* is any integer between 1 to 253), and the Subnet mask as for your PC by following the instructions below. Connect the local PCs to the LAN ports on the AP and configure the IP address manually for your PCs. 1. Click Start (in the lower left corner of the screen), right-click My Network Connections and choose Properties. Figure On the My Network Connections window shown as Figure 3-2 below, right-click LAN (Local Area Connection) and choose Properties. 9

17 Figure In the General tab of Internet Protocol (TCP/IP) Properties window, highlight Internet Protocol (TCP/IP) and click Properties. Figure

18 4. Configure the IP address manually. 1) Select Use the following IP address. 2) Enter * (* is any integer between 1 to 253) into the IP address filed, into the Subnet mask filed. 3) Click OK to keep your settings. Figure Verify the network connection between your PC and the AP via the Ping command. The following example is in Windows XP Operating System. 1) Click Start > Run tab. Enter cmd in the filed and click OK. 2) Type ping on the screen that displays and then press Enter. If the result displayed is similar to that shown in Figure 3-5 below, the connection between your PC and the AP has been successfully established. Figure

19 If the result displayed is similar to that shown in Figure 3-6 below, it means that your PC has not connected to the AP. Figure 3-6 Please check following these steps: a) Check to see if your PC and the AP are right connected. The LED of LAN port which you link to on the device and the LED on your PC s adapter should be lit up. b) Make sure the TCP/IP for your PC is right configured. If the AP s IP address is , your PC s IP address must be within the range of ~

20 Chapter 4 Configure the Device This Chapter describes how to configure your Access Point via the web-based management page. The TL-WA701ND 150Mbps Wireless Lite N Access Point is easy to configure and manage with the Web-based (Internet Explorer, Netscape Navigator, Firefox, Safari, Opera or Chrome) management page, which can be launched on any windows, Macintosh or UNIX OS with a web browser. 4.1 Login Open your web browser. Type in IP address in the address field of web browser and press Enter. Figure 4-1 Login to the AP Enter admin for the User Name and Password (both in lower case letters) in Figure 4-2 below. Then click OK or press Enter. Figure 4-2 Login Windows If the above screen does not prompt, it means that your web-browser has been set to a proxy. Go to Tools menu>internet Options>Connections>LAN Settings, in the screen that appears, cancel the Using Proxy checkbox, and click OK to finish it. After a successful login, you can configure and manage the device. There are six main menus on the leftmost column of the web-based management page: Status, QSS, Network, Wireless, DHCP and System Tools. Submenus will be available after clicking one of the main menus. On the right of the web-based management page lies the detailed explanations and instructions for the corresponding page. 4.2 Status Selecting Status will enable you to view the AP s current status and configuration, all of which is 13

21 read-only. Figure 4-3 Device Status Firmware Version - This field displays the current firmware version of the AP. Hardware Version - This field displays the current hardware version of the AP Wired - This field displays the current settings or information for the Network, including the MAC address, IP address and Subnet Mask. Wireless - This field displays basic information or status for wireless function, including Operating Mode, SSID, Channel, Mode, Channel Width, Max Tx Rate and MAC Address. Traffic Statistics - This field displays the AP's traffic statistics. System Up Time - This filed displays the run time of the AP since it s powered on or reset. 14

22 If you select Client mode in Figure 4-10, the wireless status in Figure 4-3 will change, similar to the figure below: 4.3 QSS QSS (Quick Secure Setup) can help you to quickly and securely connect to a network. This section will guide you to add a new wireless device to an existing network quickly by function. The QSS function is only available when the Operation Mode is set to Access Point and Multi-SSID. Here we take the Access Point mode for example. Select menu QSS, you will see the next screen shown in Figure 4-4. Figure 4-4 QSS Operation Mode - Displays the current operation mode of the device. QSS Status - To enable or disable the QSS function here. Current PIN - The current value of the device's PIN is displayed here. The default PIN of the device can be found in the label or User Guide. Restore PIN - Restore the PIN of the device to its default. Gen New PIN - Click this button, and then you can get a new random value for the device's PIN. You can ensure the network security by generating a new PIN. Add device - You can add a new device to the existing network manually by clicking this button. 15

23 To add a new device: If the wireless adapter supports Wi-Fi Protected Setup (WPS), you can establish a wireless connection between wireless adapter and device using either Push Button Configuration (PBC) method or PIN method. To build a successful connection by QSS, you should also do the corresponding configuration of the new device for QSS function meanwhile. For the configuration of the new device, here takes the Wireless Adapter of our company for example. I. By PBC If the wireless adapter supports Wi-Fi Protected Setup and the Push Button Configuration (PBC) method, you can add it to the network by PBC with the following two methods. Method One: Step 1: Press the QSS button on the front panel of the device. Step 2: Press and hold the QSS button of the adapter directly for 2 or 3 seconds. Step 3: Wait for a while until the next screen appears. Click Finish to complete the QSS configuration. Method Two: The QSS Configuration Screen of Wireless Adapter Step 1: Press the QSS button on the front panel of the device. 16

24 Step 2: For the configuration of the wireless adapter, please choose Push the button on my access point in the configuration utility of the QSS as below, and click Next. The QSS Configuration Screen of Wireless Adapter Step 3: Wait for a while until the next screen appears. Click Finish to complete the QSS configuration. The QSS Configuration Screen of Wireless Adapter 17

25 Method Three: Step 1: Keep the default QSS Status as Enabled and click the Add device button in Figure 4-4, then the following screen will appear. Figure 4-5 Add A New Device Step 2: Step 3: Choose Press the button of the new device in two minutes and click Connect. For the configuration of the wireless adapter, please choose Push the button on my access point in the configuration utility of the QSS as below, and click Next. The QSS Configuration Screen of Wireless Adapter Step 4: Wait for a while until the next screen appears. Click Finish to complete the QSS configuration. 18

26 The QSS Configuration Screen of Wireless Adapter II. By PIN If the new device supports Wi-Fi Protected Setup and the PIN method, you can add it to the network by PIN with the following two methods. Method One: Enter the PIN into my AP Step 1: Keep the default QSS Status as Enabled and click the Add device button in Figure 4-4, then the following screen will appear. Step 2: Choose Enter the new device's PIN and enter the PIN code (take for example)of the wireless adapter in the field after PIN as shown in the figure above. Then click Connect. The PIN code of the adapter is always displayed on the QSS configuration screen as shown in the following figure. Step 3: For the configuration of the wireless adapter, please choose Enter a PIN into my access point or a registrar in the configuration utility of the QSS as below, and click Next. 19

27 The QSS Configuration Screen of Wireless Adapter In this example, the default PIN code of this adapter is as the above figure shown. Method Two: Enter the PIN from my AP Step 1: Get the Current PIN code of the AP in Figure 4-4 (each AP has its unique PIN code. Here takes the PIN code of this AP for example). Step 2: For the configuration of the wireless adapter, please choose Enter a PIN from my access point in the configuration utility of the QSS as below, and enter the PIN code of the AP into the field after Access Point PIN. Then click Next. The QSS Configuration Screen of Wireless Adapter 20

28 The default PIN code of the AP can be found in its label or the QSS configuration screen as Figure 4-4. You will see the following screen when the new device has successfully connected to the network. a. The QSS LED on the AP will light green for five minutes if the device has been successfully added to the network. b. The QSS function cannot be configured if the Wireless function of the AP is disabled. Please make sure the Wireless function is enabled before configuring the QSS. 4.4 Network The Network option allows you to customize your local network manually by changing the default settings of the AP. Selecting Network will enable you to configure the IP parameters of Network on this page. Figure 4-6 Network Type - Select Dynamic IP to get IP address from DHCP server or select Static IP to configure IP address manually from the drop-down list. IP Address - Enter the IP address of your AP in dotted-decimal notation (factory default setting is ). 21

29 Subnet Mask - An address code that determines the size of the network. Normally use as the subnet mask. Gateway - The gateway should be in the same subnet as your IP address. MAC Address - The physical address of the AP. The value can't be changed. 1 If you change the IP Address, you must use the new IP Address to log in the AP. 2 If the new LAN IP Address you set is not in the same subnet with the IP Address pool of DHCP sever, the IP Address pool will not take effect until it is re-configured accordingly. 4.5 Wireless The Wireless option, improving functionality and performance for wireless network, can help you make the AP an ideal solution for your wireless network. Here you can create a wireless local area network just through a few settings. Wireless Settings is used for the configuration of some basic parameters of the AP. Wireless Security provides three different security types to secure your data and thus provide greater security for your wireless network. MAC filtering allows you to control the access of wireless stations to the AP. Wireless Advanced allows you to configure some advanced parameters for the AP. Throughput Monitor helps to watch wireless throughput information Wireless statistics enables you to get detailed information about the current connected wireless stations. There are six submenus under the Wireless menu (shown in Figure 4-7): Wireless Settings, Wireless Security, Wireless MAC Filtering, Wireless Advanced, Throughput Monitor and Wireless Statistics. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below Wireless Settings Figure 4-7 Wireless menu Selecting Wireless > Wireless Settings will enable you to configure the basic settings for your wireless network on the screen below (Figure 4-8).This page allows you to configure the wireless mode for your device. Six operation modes are supported here, including Access Point, Multi-SSID, Client, Repeater, Universal Repeater and Bridge with AP. The available setting options for each operation mode are different from those of the other. 22

30 1) Access Point: This mode allows wireless stations to access this device. Figure 4-8 Wireless Settings in Access Point mode SSID (Set Service Identifier) - Identifies your wireless network name. Create a name up to 32 characters and make sure all wireless points in the wireless network with the same SSID. The default SSID is TP-LINK_XXXXXX (XXXXXX indicates the last unique six characters of each device s MAC address). This value is case-sensitive. For example, TEST is NOT the same as test. Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the device can be used. It may be illegal to use the wireless function of the device in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance. When you select your local region from the pull-down list, click the Save button, then the Note Dialog appears. Click OK. Note Dialog Limited by local law regulations, version for North America does not have region selection 23

31 option. Channel - Determines the operating frequency to be used. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point. Mode - Select the desired wireless mode. The options are: 11b only - Only b wireless stations can connect to the device. 11g only - Only g wireless stations can connect to the device. 11n only - Only n wireless stations can connect to the device. 11bg mixed - Both b and g wireless stations can connect to the device. 11bgn mixed - All b, g and n wireless stations can connect to the device. Channel Width - Determines the channel width to be used. It is unnecessary to change the default value unless required. Max Tx Rate - Specifies the maximum transmit rate of the device through this field. Enable Wireless Radio - Select or deselect this check box to allow or deny wireless stations to access the device. Enable SSID Broadcast - Select or deselect this check box to allow or deny the device to broadcast its name (SSID) on the air. If it s allowed, when wireless clients survey the local area for wireless networks to associate with, they will detect the SSID broadcast by the device. To apply any settings you have altered on the page, please click the Save button, and then you will be reminded to reboot the device. 24

32 2) Multi-SSID: This mode allows the device to support up to 4 SSIDs. Figure 4-9 Wireless Settings in Multi-SSID mode Enable VLAN - Check this box and then you can change the VLANID of each SSID. If you want to configure the Guest and Internal networks on VLAN, the switch you are using must support VLAN. As a prerequisite step, configure a port on the switch for handling VLAN tagged packets as described in the IEEE802.1Q standard, and enable this field. SSID (1-4) - Up to 4 SSIDs for each BSS can be entered in the filed SSID1 ~ SSID4. The name can be up to 32 characters. The same name (SSID) must be assigned to all wireless devices in your network. If Enable VLAN is checked, the wireless stations connecting to SSID of different VLANID can not communicate with each other. VLANID (1-4) - Provide a number between 1 and 4095 for VLAN. This will cause the device to send packets with VLAN tags. The switch connecting with the device must support VLAN IEEE802.1Q frames. The wireless stations connecting to the SSID of a specified VLANID can communicate with the PC connecting to the port with the same VLANID on the Switch. Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the device can be used. It may be illegal to use the wireless function of the device in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance. 25

33 When you select your local region from the pull-down list, click the Save button, then the Note Dialog appears. Click OK. Note Dialog Limited by local law regulations, version for North America does not have region selection option. Channel - Determines the operating frequency to be used. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point. Mode - This field determines the wireless mode which the device works on. 11b only - Only b wireless stations can connect to the device. 11g only - Only g wireless stations can connect to the device. 11n only - Only n wireless stations can connect to the device. 11bg mixed - Both b and g wireless stations can connect to the device. 11bgn mixed - All b, g and n wireless stations can connect to the device. Channel Width - Determines the channel width to be used. It is unnecessary to change the default value unless required. Max Tx Rate - Specifies the maximum transmit rate of the device through this field. Enable Wireless Radio - Select or deselect this check box to allow or deny wireless stations to access the device. Enable SSID Broadcast - Select or deselect this check box to allow or deny the device to broadcast its name (SSID) on the air. If it s allowed, when wireless clients survey the local area for wireless networks to associate with, they will detect the SSID broadcast by the device. To apply any settings you have altered on the page, please click the Save button, and then you will be reminded to reboot the device. 26

34 3) Client: This mode allows the device to act as a wireless station to enable wired host(s) to access an AP. Figure 4-10 Wireless Settings in Client mode Enable WDS - The client can connect to AP with WDS enabled or disabled. If WDS is enabled, all traffic from wired networks will be forwarded in the format of WDS frames consisting of four address fields. If WDS is disabled, three address frames are used. If your AP supports WDS well, please enable this option. SSID - If you select the radio button before SSID, the AP client will connect to the AP according to SSID. Enter the SSID of AP that you want to access. MAC of AP - If you select the radio button before MAC of AP, the AP client will connect to the AP according MAC address. Enter the MAC address of AP that you want to access. Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the device can be used. It may be illegal to use the wireless function of the device in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance. When you select your local region from the pull-down list, click the Save button, then the Note Dialog appears. Click OK. Note Dialog 27

35 Limited by local law regulations, version for North America does not have region selection option. Channel Width - Determines the channel width to be used. It is unnecessary to change the default value unless required. Enable Wireless Radio - Select or deselect this check box to allow or deny wireless stations to access the device. Click the Search button to detect the SSIDs in the local area. To apply any settings you have altered on the page, please click the Save button, and then you will be reminded to reboot the device. 4) Repeater: This mode allows the AP with its own BSS to relay data to a root AP to which it is associated with WDS enabled. The wireless repeater relays signal between its stations and the root AP for greater wireless range. Figure 4-11 Wireless Settings in Repeater mode MAC of AP - Enter the MAC address of the root AP of which you want to expand wireless range. Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the device can be used. It may be illegal to use the wireless function of the device in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance. 28

36 When you select your local region from the pull-down list, click the Save button, then the Note Dialog appears. Click OK. Note Dialog Limited by local law regulations, version for North America does not have region selection option. Channel Width - Determines the channel width to be used. It is unnecessary to change the default value unless required. Max Tx Rate - Specifies the maximum transmit rate of the device through this field. Enable Wireless Radio - Select or deselect this check box to allow or deny wireless stations to access the device. Click the Search button to detect the SSIDs in the local area. To apply any settings you have altered on the page, please click the Save button, and then you will be reminded to reboot the device. 29

37 5) Universal Repeater: This mode allows the AP with its own BSS to relay data to a root AP to which it is associated with WDS disabled. The wireless repeater relays signal between its stations and the root AP for greater wireless range. Figure 4-12 Wireless Settings in Repeater mode MAC of AP - Enter the MAC address of the root AP of which you want to expand wireless range. Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the device can be used. It may be illegal to use the wireless function of the device in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance. When you select your local region from the pull-down list, click the Save button, then the Note Dialog appears. Click OK. Note Dialog Limited by local law regulations, version for North America does not have region selection option. Channel Width - Determines the channel width to be used. It is unnecessary to change the default value unless required. 30

38 Max Tx Rate - Specifies the maximum transmit rate of the device through this field. Enable Wireless Radio - Select or deselect this check box to allow or deny wireless stations to access the device. Click the Search button to detect the SSIDs in the local area. To apply any settings you have altered on the page, please click the Save button, and then you will be reminded to reboot the device. 6) Bridge with AP: This mode can bridge the AP and up to 4 APs also in bridge mode to connect two or more wired LANs. Figure 4-13 Wireless Settings in Repeater mode SSID (Set Service Identifier) - Identifies your wireless network name. Create a name up to 32 characters and make sure all wireless points in the wireless network with the same SSID. The default SSID is TP-LINK_XXXXXX (XXXXXX indicates the last unique six characters of each device s MAC address). This value is case-sensitive. For example, TEST is NOT the same as test. 31

39 Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the device can be used. It may be illegal to use the wireless function of the device in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance. When you select your local region from the pull-down list, click the Save button, then the Note Dialog appears. Click OK. Note Dialog Limited by local law regulations, version for North America does not have region selection option. Channel - Determines the operating frequency to be used. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point. Mode - This field determines the wireless mode which the device works on. 11b only - Only b wireless stations can connect to the device. 11g only - Only g wireless stations can connect to the device. 11n only - Only n wireless stations can connect to the device. 11bg mixed - Both b and g wireless stations can connect to the device. 11bgn mixed - All b, g and n wireless stations can connect to the device. Channel Width - Determines the channel width to be used. It is unnecessary to change the default value unless required. Max Tx Rate - Specifies the maximum transmit rate of the device through this field. Enable Wireless Radio - Select or deselect this check box to allow or deny wireless stations to access the device. Enable SSID Broadcast - Select or deselect this check box to allow or deny the device to broadcast its name (SSID) on the air. If it s allowed, when wireless clients survey the local area for wireless networks to associate with, they will detect the SSID broadcast by the device. MAC of AP (1-4) - Enter the MAC address of other AP(s). Click the Search button to detect the SSIDs in the local area. To apply any settings you have altered on the page, please click the Save button, and then you will be reminded to reboot the device Wireless Security Selecting Wireless > Wireless Security will enable you to configure wireless security for your 32

40 wireless network to protect your data from intruders. The AP provides three security types: WEP, WPA/WPA2 and WPA-PSK/WPA2-PSK. Wireless security can be set on the following screen shown as Figure The security options are different for different operation mode. 1) Access Point Figure 4-14 Wireless Security - Access Point Operation Mode - Shows the current operation mode. Disable Security - Check this box radio button to disable wireless security. If disabled, the wireless stations will be able to connect this device without encryption. It is strongly recommended that you choose one of the security types to enable security. WEP - Select WEP security. Type - You can select one of following types. 1) Automatic - Select Shared Key or Open System authentication type automatically based on the wireless station's capability and request. 33

41 2) Shared Key - Select Shared Key authentication type. 3) Open System - Select Open System authentication. WEP Key Format - You can select ASCII or Hexadecimal format. ASCII format stands for any combination of keyboard characters in the specified length. Hexadecimal format stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length. WEP Key - Select which of the four keys will be used and enter the matching WEP key information for your network in the selected key radio button. These values must be identical on all wireless stations in your network. Key Type - You can select the WEP key length (64-bit, or 128-bit, or 152-bit.) for encryption. "Disabled" means this WEP key entry is invalid. 1) For 64-bit encryption - You can enter 10 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not permitted) or 5 ASCII characters. 2) For 128-bit encryption - You can enter 26 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not permitted) or 13 ASCII characters. 3) For 152-bit encryption - You can enter 32 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not permitted) or 16 ASCII characters. If you do not set the key, the wireless security function is still disabled even if you have selected Shared Key as Authentication Type. WPA/WPA2 - Select WPA/WPA2 based on Radius Server. Version - You can select one of following versions. 1) Automatic - Select WPA or WPA2 automatically based on the wireless station's capability and request. 2) WPA - Wi-Fi Protected Access. 3) WPA2 - WPA version 2. Encryption - You can select either Automatic, TKIP or AES. Radius Server IP - Enter the IP address of the Radius Server. Radius Port - Enter the port used by radius service. Radius Password - Enter the password for the Radius Server. Group Key Update Period - Specify the group key update interval in seconds. The value can be either 0 or at least 30. Enter 0 to disable the update. WPA-PSK/ WPA2-PSK - Select WPA based on pre-shared key. Version - You can select one of following versions. 1) Automatic - Select WPA-PSK or WPA2-PSK automatically based on the wireless station's capability and request. 2) WPA-PSK - Pre-shared key of WPA. 3) WPA2-PSK - Pre-shared key of WPA2. 34

42 Encryption - When you select WPA-PSK or WPA2-PSK for Authentication Type, you can select either Automatic, TKIP or AES as Encryption. PSK Passphrase - Enter a passphrase here. Group Key Update Period - Specify the group key update interval in seconds. The value can be either 0 or at least 30. Enter 0 to disable the update. Be sure to click the Save button to save your settings on this page. You will be reminded to reboot the device after clicking the Save button. 2) Multi-SSID Figure 4-15 Wireless Security Multi-SSID Operation Mode - Shows the current operation mode. You can choose one of the 4 SSID from the pull-down list. Disable Security - Check this box radio button to disable wireless security. If disabled, the wireless stations will be able to connect this device without encryption. It is strongly recommended that you choose one of the security types to enable security. WPA/WPA2 - Select WPA/WPA2 based on Radius Server. Version - You can select one of following versions. 35

43 1) Automatic - Select WPA or WPA2 automatically based on the wireless station's capability and request. 2) WPA - Wi-Fi Protected Access. 3) WPA2 - WPA version 2. Encryption - You can select either Automatic, TKIP or AES. Radius Server IP - Enter the IP address of the Radius Server. Radius Port - Enter the port used by radius service. Radius Password - Enter the password for the Radius Server. Group Key Update Period - Specify the group key update interval in seconds. The value can be either 0 or at least 30. Enter 0 to disable the update. This security option will become unavailable, if the Enable VLAN box in Figure 4-9 is checked. WPA-PSK/ WPA2-PSK - Select WPA based on pre-shared key. Version - You can select one of following versions. 1) Automatic - Select WPA-PSK or WPA2-PSK automatically based on the wireless station's capability and request. 2) WPA-PSK - Pre-shared key of WPA. 3) WPA2-PSK - Pre-shared key of WPA2. Encryption - When you select WPA-PSK or WPA2-PSK for Authentication Type, you can select either Automatic, TKIP or AES as Encryption. PSK Passphrase - Enter a passphrase here. Group Key Update Period - Specify the group key update interval in seconds. The value can be either 0 or at least 30. Enter 0 to disable the update. Be sure to click the Save button to save your settings on this page. You will be reminded to reboot the device after clicking the Save button. 36

44 3) Client Figure 4-16 Wireless Security Client Operation Mode - Shows the current operation mode. Disable Security - Check this box radio button to disable wireless security. If disabled, the wireless stations will be able to connect this device without encryption. It is strongly recommended that you choose one of the security types to enable security. WEP - Select WEP security. Type - You can select one of following types. 1) Automatic - Select Shared Key or Open System authentication type automatically based on the wireless station's capability and request. 2) Shared Key - Select Shared Key authentication type. 3) Open System - Select Open System authentication. WEP Key Format - You can select ASCII or Hexadecimal format. ASCII format stands for any combination of keyboard characters in the specified length. Hexadecimal format stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length. WEP Key - Select which of the four keys will be used and enter the matching WEP key information for your network in the selected key radio button. These values must be identical on all wireless stations in your network. 37

45 Key Type - You can select the WEP key length (64-bit, or 128-bit, or 152-bit.) for encryption. "Disabled" means this WEP key entry is invalid. 1) For 64-bit encryption - You can enter 10 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not permitted) or 5 ASCII characters. 2) For 128-bit encryption - You can enter 26 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not permitted) or 13 ASCII characters. 3) For 152-bit encryption - You can enter 32 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not permitted) or 16 ASCII characters. If you do not set the key, the wireless security function is still disabled even if you have selected Shared Key as Authentication Type. WPA-PSK/ WPA2-PSK - Select WPA based on pre-shared key. Version - You can select one of following versions. 1) Automatic - Select WPA-PSK or WPA2-PSK automatically based on the wireless station's capability and request. 2) WPA-PSK - Pre-shared key of WPA. 3) WPA2-PSK - Pre-shared key of WPA2. Encryption - When you select WPA-PSK or WPA2-PSK for Authentication Type, you can select either Automatic, TKIP or AES as Encryption. PSK Passphrase - Enter a passphrase here. Group Key Update Period - Specify the group key update interval in seconds. The value can be either 0 or at least 30. Enter 0 to disable the update. Be sure to click the Save button to save your settings on this page. You will be reminded to reboot the device after clicking the Save button. 38

46 4) Repeater Figure 4-17 Wireless Security Repeater Operation Mode - Shows the current operation mode. Disable Security - Check this box radio button to disable wireless security. If disabled, the wireless stations will be able to connect this device without encryption. It is strongly recommended that you choose one of the security types to enable security. WEP - Select WEP security. Type - You can select one of following types. 1) Automatic - Select Shared Key or Open System authentication type automatically based on the wireless station's capability and request. 2) Shared Key - Select Shared Key authentication type. 3) Open System - Select Open System authentication. WEP Key Format - You can select ASCII or Hexadecimal format. ASCII format stands for any combination of keyboard characters in the specified length. Hexadecimal format stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length. WEP Key - Select which of the four keys will be used and enter the matching WEP key information for your network in the selected key radio button. These values must be identical on all wireless stations in your network. 39

TL-WA801ND 300Mbps Wireless N Access Point

TL-WA801ND 300Mbps Wireless N Access Point 300Mbps Wireless N Access Point Rev: 1.0.0 1910010218 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands

More information

TL-WA830RE 300Mbps Wireless N Range Extender

TL-WA830RE 300Mbps Wireless N Range Extender 300Mbps Wireless N Range Extender Rev: 1.0.0 1910010538 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands

More information

TL-WA730RE 150Mbps Wireless Range Extender

TL-WA730RE 150Mbps Wireless Range Extender 150Mbps Wireless Range Extender Rev: 1.0.0 1910010310 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands

More information

WNAP n Wireless Access Point. User's Manual

WNAP n Wireless Access Point. User's Manual WNAP-1110 802.11n Wireless Access Point User's Manual Copyright Copyright 2010 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored

More information

Rev:

Rev: TL-WA7510N -WA7510N 5GHz 150Mbps Outdoor Wireless Access Point Rev: 1.0.0 1910010534 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES

More information

TL-WA5210G 2.4GHz High Power Wireless Outdoor CPE

TL-WA5210G 2.4GHz High Power Wireless Outdoor CPE TL-WA5210G 2.4GHz High Power Wireless Outdoor CPE Rev: 1.0.0 1910010274 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO.,

More information

TL-WR340G TL-WR340GD 54Mbps Wireless Router

TL-WR340G TL-WR340GD 54Mbps Wireless Router TL-WR340G TL-WR340GD 54Mbps Wireless Router Rev: 1.0.4 1910010400 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD.

More information

TL-WA801ND 300Mbps Wireless N Access Point

TL-WA801ND 300Mbps Wireless N Access Point 300Mbps Wireless N Access Point Rev: 2.0.0 1910010673 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands

More information

TL-WA500G 54M Wireless Access Point

TL-WA500G 54M Wireless Access Point 54M Wireless Access Point Rev: 1.0.1 1910010273 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and

More information

LevelOne User Manual WPC-0600 N_One Wireless CardBus Adapter

LevelOne User Manual WPC-0600 N_One Wireless CardBus Adapter LevelOne User Manual WPC-0600 N_One Wireless CardBus Adapter V2.0.0-0712 Safety FCC WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

More information

TL-WA701ND 150Mbps Wireless N Access Point

TL-WA701ND 150Mbps Wireless N Access Point 150Mbps Wireless N Access Point Rev: 3.0.0 1910010669 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands

More information

TL-WA601G 108M Wireless Access Point

TL-WA601G 108M Wireless Access Point TL-WA601G 108M Wireless Access Point Rev 1.0.1 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product

More information

User Manual. PePWave Surf / Surf AP Indoor Series: Surf 200, E200, AP 200, AP 400. PePWave Mesh Connector Indoor Series: MC 200, E200, 400

User Manual. PePWave Surf / Surf AP Indoor Series: Surf 200, E200, AP 200, AP 400. PePWave Mesh Connector Indoor Series: MC 200, E200, 400 User Manual PePWave Surf / Surf AP Indoor Series: Surf 200, E200, AP 200, AP 400 PePWave Mesh Connector Indoor Series: MC 200, E200, 400 PePWave Surf AP Series: Surf AP 200-X, E200-X, 400-X PePWave Surf

More information

TL-WR702N 150Mbps Wireless N Nano Router

TL-WR702N 150Mbps Wireless N Nano Router Rev: 1.0.0 1910010547 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks

More information

TL-WA601G 108M Wireless Access Point

TL-WA601G 108M Wireless Access Point 108M Wireless Access Point Rev: 1.0.3 1910010121 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and

More information

TL-WR340G TL-WR340GD 54Mbps Wireless Router

TL-WR340G TL-WR340GD 54Mbps Wireless Router TL-WR340G TL-WR340GD 54Mbps Wireless Router Rev: 1.0.5 1910010474 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD.

More information

150M Wireless-N Outdoor AP Router

150M Wireless-N Outdoor AP Router 150M Wireless-N Outdoor AP Router Model No. ib-or246150n QIG Ver.: 2.0.0 FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part

More information

TL-WR743ND 150Mbps Wireless AP/Client Router

TL-WR743ND 150Mbps Wireless AP/Client Router Rev: 1.0.0 1910010341 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks

More information

TL-WR543G 54M Wireless AP Client Router

TL-WR543G 54M Wireless AP Client Router 54M Wireless AP Client Router Rev: 1.0.2 I 1910010062 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands

More information

WUA-0605 300Mbps Wireless USB Network Adapter

WUA-0605 300Mbps Wireless USB Network Adapter WUA-0605 300Mbps Wireless USB Network Adapter User Manual V1.0 Certification FCC CE FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

More information

TL-WR641G 108M Wireless Router

TL-WR641G 108M Wireless Router 108M Wireless Router Rev: 1.1.0 19100100141 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product

More information

TL-WR340G/TL-WR340GD User Guide 54M Wireless Router

TL-WR340G/TL-WR340GD User Guide 54M Wireless Router User Guide 54M Wireless Router Rev: 1.0.2 1910010064 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands

More information

TL-WR743ND 150Mbps Wireless AP/Client Router

TL-WR743ND 150Mbps Wireless AP/Client Router Rev: 1.0.0 1910010341 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks

More information

TL-WR740N TL-WR741ND 150Mbps Wireless N Router

TL-WR740N TL-WR741ND 150Mbps Wireless N Router TL-WR740N TL-WR741ND Rev: 3.0.0 1910010520 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product

More information

COPYRIGHT & TRADEMARKS

COPYRIGHT & TRADEMARKS COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK Technologies Co., Ltd. Other brands and product names are trademarks or registered trademarks

More information

TL-WA901ND 300Mbps Wireless N Access Point

TL-WA901ND 300Mbps Wireless N Access Point TL-WA901ND 300Mbps Wireless N Access Point REV2.0.1 1910010841 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other

More information

FCC STATEMENT. FCC RF Radiation Exposure Statement. CE Declaration of Conformity

FCC STATEMENT. FCC RF Radiation Exposure Statement. CE Declaration of Conformity FCC STATEMENT This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

More information

TL-WR1043N TL-WR1043ND Wireless N Gigabit Router

TL-WR1043N TL-WR1043ND Wireless N Gigabit Router TL-WR1043N TL-WR1043ND Rev: 1.0.0 1910010216 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product

More information

TL-WR941N TL-WR941ND Wireless N Router

TL-WR941N TL-WR941ND Wireless N Router TL-WR941N TL-WR941ND Wireless N Router Rev: 1.0.0 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and

More information

TL-WR340G/TL-WR340GD 54M Wireless Router

TL-WR340G/TL-WR340GD 54M Wireless Router 54M Wireless Router Rev:1.0.0 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are

More information

TL-WA901ND 450Mbps Wireless N Access Point

TL-WA901ND 450Mbps Wireless N Access Point TL-WA901ND 450Mbps Wireless N Access Point REV2.0.0 1910010841 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other

More information

Chapter 2 Configuring Your Wireless Network and Security Settings

Chapter 2 Configuring Your Wireless Network and Security Settings Chapter 2 Configuring Your Wireless Network and Security Settings This chapter describes how to configure the wireless features of your DG834N RangeMax TM NEXT Wireless ADSL2+ Modem Router. For a wireless

More information

Link Link sys E3000 sys RE1000

Link Link sys E3000 sys RE1000 User Guide High Performance Extender Wireless-N Router Linksys Linksys RE1000 E3000Wireless-N Table of Contents Contents Chapter 1: Product Overview 1 Front 1 Top 1 Bottom 1 Back 2 Chapter 2: Advanced

More information

WAP3205 v2. User s Guide. Quick Start Guide. Wireless N300 Access Point. Default Login Details. Version 1.00 Edition 2, 10/2015

WAP3205 v2. User s Guide. Quick Start Guide. Wireless N300 Access Point. Default Login Details. Version 1.00 Edition 2, 10/2015 WAP3205 v2 Wireless N300 Access Point Version 1.00 Edition 2, 10/2015 Quick Start Guide User s Guide Default Login Details Web Address http://zyxelsetup Password www.zyxel.com 1234 Copyright 2014 ZyXEL

More information

TL-R402M Cable/DSL Router

TL-R402M Cable/DSL Router Cable/DSL Router Rev: 3.0.2 1910010053 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names

More information

USER GUIDE Cisco Small Business

USER GUIDE Cisco Small Business USER GUIDE Cisco Small Business WBPN Wireless-N Bridge for Phone Adapters December 2011 Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries.

More information

WR1500N 150Mbps Wireless N Router

WR1500N 150Mbps Wireless N Router WR1500N 150Mbps Wireless N Router 1910020625 REV 2.1.0 FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

More information

Quick Installation Guide of Wireless g Broadband Router

Quick Installation Guide of Wireless g Broadband Router To avoid users without access right through your WLAN Broadband Router, suggest that use security mechanism like WEP, WPA or set ID/password for web configuration login IP address 192.168.1.254. Preparation

More information

Wireless N 150 USB Adapter with 10dBi High Gain Antenna. Model # AWLL5055 User s Manual. Rev. 1.0

Wireless N 150 USB Adapter with 10dBi High Gain Antenna. Model # AWLL5055 User s Manual. Rev. 1.0 Wireless N 150 USB Adapter with 10dBi High Gain Antenna Model # AWLL5055 User s Manual Rev. 1.0 Table of Contents 1. Introduction...2 1.1 Package Contents...2 1.2 Features...2 2. Install Wireless USB Adapter...3

More information

TL-WR642G 108M Wireless Router

TL-WR642G 108M Wireless Router 108M Wireless Router Rev:1.1.0 1910010142 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product

More information

TL-PS310U Single USB 2.0 Port MFP and Storage Server

TL-PS310U Single USB 2.0 Port MFP and Storage Server TL-PS310U Single USB 2.0 Port MFP and Storage Server Rev: 2.0.0 1910010313 Contents Chapter 1 Introduction... 1 1.1 Product Overview...1 1.2 Network Management...1 1.3 Components and Features...1 1.4 Hardware

More information

TL-WR642G 108M Wireless Router

TL-WR642G 108M Wireless Router 108M Wireless Router Rev:1.0.1 1910010005 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product

More information

TL-WR740N Wireless Lite N Router

TL-WR740N Wireless Lite N Router Rev: 1.0.0 1910010197 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks

More information

Netis WF-2301 150Mbps Wireless N Outdoor AP User Manual

Netis WF-2301 150Mbps Wireless N Outdoor AP User Manual Netis WF-2301 150Mbps Wireless N Outdoor AP User Manual 1141 Budapest, Fogarasi út 77. Tel.: *220-7940, 220-7814, 220-7959, 220-8881, 364-3428 Fax: 220-7940 Mobil: 30 531-5454, 30 939-9989 1095 Budapest,

More information

Wireless LAN Access Point. IEEE 802.11g 54Mbps. User s Manual

Wireless LAN Access Point. IEEE 802.11g 54Mbps. User s Manual Wireless LAN Access Point IEEE 802.11g 54Mbps User s Manual Table of Contents Chapter 1 Introduction... 1 1.1 Package Contents...2 1.2 Features...2 1.3 Specifications...2 1.4 Physical Description...3 Chapter

More information

TL-WN7200N 150Mbps High Power Wireless USB Adapter

TL-WN7200N 150Mbps High Power Wireless USB Adapter 150Mbps High Power Wireless USB Adapter Rev: 1.0.0 1910010295 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other

More information

TL-WR340G/TL-WR340GD User Guide 54M Wireless Router

TL-WR340G/TL-WR340GD User Guide 54M Wireless Router User Guide 54M Wireless Router Rev:1.0.2 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product

More information

TL-WN310G 54M Wireless CardBus Adapter

TL-WN310G 54M Wireless CardBus Adapter 54M Wireless CardBus Adapter Rev: 1.0.1 1910010042 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and

More information

Assign a static IP address 192.168.1.100 for your computer. Please refer to the T3 in Troubleshooting guide if you need assistance.

Assign a static IP address 192.168.1.100 for your computer. Please refer to the T3 in Troubleshooting guide if you need assistance. Note The product model shown in this QIG is TL-WA701ND, as an example. Assign a static IP address 192.168.1.100 for your computer. Please refer to the T3 in Troubleshooting guide if you need assistance.

More information

Chapter 2 Wireless Settings and Security

Chapter 2 Wireless Settings and Security Chapter 2 Wireless Settings and Security This chapter describes how to set up the wireless features of your WGT624 v4 wireless router. In planning your wireless network, select a location for the wireless

More information

TL-WR710N 150Mbps Wireless N Mini Pocket Router

TL-WR710N 150Mbps Wireless N Mini Pocket Router Rev: 1.0.0 1910010795 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks

More information

TL-WA730RE 150Mbps Wireless N Range Extender

TL-WA730RE 150Mbps Wireless N Range Extender 150Mbps Wireless N Range Extender Rev: 2.0.0 1910010693 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands

More information

TL-WN822N 300Mbps High Gain Wireless N USB Adapter

TL-WN822N 300Mbps High Gain Wireless N USB Adapter Rev: 2.0.0 1910010470 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks

More information

WRE2205. User s Guide. Quick Start Guide. Wireless N300 Range Extender. Default Login Details. Version 1.00 Edition 1, 06/2012

WRE2205. User s Guide. Quick Start Guide. Wireless N300 Range Extender. Default Login Details. Version 1.00 Edition 1, 06/2012 WRE2205 Wireless N300 Range Extender Version 1.00 Edition 1, 06/2012 Quick Start Guide User s Guide Default Login Details LAN IP Address http://192.168.1.2 User Name admin Passwordwww.zyxel.com 1234 Copyright

More information

TL-WPA4220 300Mbps AV500 WiFi Powerline Extender TL-WPA2220 300Mbps AV200 WiFi Powerline Extender

TL-WPA4220 300Mbps AV500 WiFi Powerline Extender TL-WPA2220 300Mbps AV200 WiFi Powerline Extender TL-WPA4220 300Mbps AV500 WiFi Powerline Extender TL-WPA2220 300Mbps AV200 WiFi Powerline Extender REV1.0.0 1910010839 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered

More information

WRE6505. User s Guide. Quick Start Guide. Wireless AC750 Range Extender. Default Login Details. Version 1.00 Edition 1, 4 2014

WRE6505. User s Guide. Quick Start Guide. Wireless AC750 Range Extender. Default Login Details. Version 1.00 Edition 1, 4 2014 WRE6505 Wireless AC750 Range Extender Version 1.00 Edition 1, 4 2014 2.4G 5G Quick Start Guide User s Guide Default Login Details LAN IP Address 192.168.1.2 User Name admin www.zyxel.com Password 1234

More information

LevelOne WAP - 0005. User s Manual. 108 Mbps Wireless Access Point

LevelOne WAP - 0005. User s Manual. 108 Mbps Wireless Access Point LevelOne WAP - 0005 108 Mbps Wireless Access Point User s Manual TABLE OF CONTENTS CHAPTER 1 INTRODUCTION... 1 Features of your Wireless Access Point... 1 Package Contents... 3 Physical Details... 3 CHAPTER

More information

Ethernet Radio Configuration Guide

Ethernet Radio Configuration Guide Ethernet Radio Configuration Guide for Gateway, Endpoint, and Repeater Radio Units April 20, 2015 Customer Service 1-866-294-5847 Baseline Inc. www.baselinesystems.com Phone 208-323-1634 FAX 208-323-1834

More information

A Division of Cisco Systems, Inc. GHz 2.4 802.11g. Wireless-G. Access Point with SRX. User Guide WIRELESS WAP54GX. Model No.

A Division of Cisco Systems, Inc. GHz 2.4 802.11g. Wireless-G. Access Point with SRX. User Guide WIRELESS WAP54GX. Model No. A Division of Cisco Systems, Inc. GHz 2.4 802.11g WIRELESS Wireless-G Access Point with SRX User Guide Model No. WAP54GX Copyright and Trademarks Specifications are subject to change without notice. Linksys

More information

Turn on all of your network devices and then check to see if the LEDs on the Access Point display normally as the diagram below describes.

Turn on all of your network devices and then check to see if the LEDs on the Access Point display normally as the diagram below describes. Connect to the Access Point with the Ethernet cable or via wireless. The default SSID of the Access Point is TP-LINK_ XXXXXX. The XXXXXX is the last 6 characters of the Access Point s MAC address. Plug

More information

MN-700 Base Station Configuration Guide

MN-700 Base Station Configuration Guide MN-700 Base Station Configuration Guide Contents pen the Base Station Management Tool...3 Log ff the Base Station Management Tool...3 Navigate the Base Station Management Tool...4 Current Base Station

More information

TL-WN422G High-Power Wireless USB Adapter

TL-WN422G High-Power Wireless USB Adapter High-Power Wireless USB Adapter Rev:1.0.0 1910010090 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands

More information

TL-MR3420 3G/3.75G Wireless N Router

TL-MR3420 3G/3.75G Wireless N Router Rev: 1.0.0 1910010314 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks

More information

TL-WPA281/TL-WPA271 Wireless N Powerline Extender

TL-WPA281/TL-WPA271 Wireless N Powerline Extender Rev: 1.0.0 1910010522 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks

More information

TL-MR3220 3G/3.75G Wireless Lite N Router

TL-MR3220 3G/3.75G Wireless Lite N Router Rev: 1.0.0 1910010350 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks

More information

Wireless AC 1200 PCI Adapter. Model # AWLH7086-E User s Manual. Rev. 1.0

Wireless AC 1200 PCI Adapter. Model # AWLH7086-E User s Manual. Rev. 1.0 Wireless AC 1200 PCI Adapter Model # AWLH7086-E User s Manual Rev. 1.0 Table of Contents 1. Introduction... 3 1.1 Package Contents... 3 1.2 Features... 3 2. Install the Wireless PCI Adapter... 4 3. Connect

More information

TG-3468 Gigabit PCI Express Network Adapter

TG-3468 Gigabit PCI Express Network Adapter TG-3468 Rev:2.0.0 1910010580 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks

More information

User s Manual. Version 1.0. Date: 2009/1/07

User s Manual. Version 1.0. Date: 2009/1/07 VigorAP 700 Wireless Access Point User s Manual Version 1.0 Date: 2009/1/07 COPYRIGHT Copyright 2008/2009 by this company. All rights reserved. No part of this publication may be reproduced, transmitted,

More information

Linksys WAP300N. User Guide

Linksys WAP300N. User Guide User Guide Contents Contents Overview Package contents 1 Back view 1 Bottom view 2 How to expand your home network 3 What is a network? 3 How to expand your home network 3 Where to find more help 3 Operating

More information

TL-PS310U Single USB 2.0 Port MFP and Storage Server

TL-PS310U Single USB 2.0 Port MFP and Storage Server Single USB 2.0 Port MFP and Storage Server REV3.0.0 1910010947 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other

More information

WL-5450AP & WL-5460AP Wireless Access Point. User s Guide

WL-5450AP & WL-5460AP Wireless Access Point. User s Guide WL-5450AP & WL-5460AP Wireless Access Point User s Guide 1 FCC Certifications This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

More information

Networking. General networking. Networking overview. Common home network configurations. Wired network example. Wireless network examples

Networking. General networking. Networking overview. Common home network configurations. Wired network example. Wireless network examples Networking General networking Networking overview A network is a collection of devices such as computers, printers, Ethernet hubs, wireless access points, and routers connected together for communication

More information

AIP-W512. 802.11n Packet Travel Router. Rev: 1.0.0

AIP-W512. 802.11n Packet Travel Router. Rev: 1.0.0 802.11n Packet Travel Router Rev: 1.0.0 FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits

More information

WLAN660 Wireless IP Phone Administrator s Guide

WLAN660 Wireless IP Phone Administrator s Guide FEDERAL COMMUNICATIONS COMMISSION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this

More information

PCMCIA Wireless LAN Card User s Manual

PCMCIA Wireless LAN Card User s Manual PCMCIA Wireless LAN Card User s Manual Rev 1.0 Regulatory compliance FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of

More information

WLAN600 Wireless IP Phone Administrator s Guide

WLAN600 Wireless IP Phone Administrator s Guide WLAN600 Wireless IP Phone Administrator s Guide Trademark Acknowledgement All brand names are trademarks or registered trademarks of their respective companies. Disclaimer This document is supplied by

More information

Wireless Access Point

Wireless Access Point Wireless Access Point USER MANUAL This manual has been prepared by AirTies Wireless Networks Corporation. All rights reserved. Manual Overview This manual guides you through the steps necessary for setting

More information

User Guide. E-Series Routers

User Guide. E-Series Routers User Guide E-Series Routers Table of Contents Table of Contents Product overview E900/E1200/E1500/E2500/E3200 1 Back view 1 Bottom view 1 E4200 2 Top view 2 Back view 2 Setting Up Your E-Series Router

More information

Version 1.01 28/08/2014. User Manual. DAP-1665 Wireless AC1200 Dual Band Access Point DAP-1665

Version 1.01 28/08/2014. User Manual. DAP-1665 Wireless AC1200 Dual Band Access Point DAP-1665 Version 1.01 28/08/2014 User Manual DAP-1665 Wireless AC1200 Dual Band Access Point DAP-1665 Preface D-Link reserves the right to revise this publication and to make changes in the content hereof without

More information

TL-R460 Cable/DSL Router

TL-R460 Cable/DSL Router Cable/DSL Router Rev: 2.0.0 1910010471 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names

More information

Nokia Siemens Networks. CPEi-lte 7212. User Manual

Nokia Siemens Networks. CPEi-lte 7212. User Manual Nokia Siemens Networks CPEi-lte 7212 User Manual Contents Chapter 1: CPEi-lte 7212 User Guide Overview... 1-1 Powerful Features in a Single Unit... 1-2 Front of the CPEi-lte 7212... 1-2 Back of the CPEi-lte

More information

11N Multi-Function Access Point EAP300 11N Multi-Function Access Point

11N Multi-Function Access Point EAP300 11N Multi-Function Access Point 1 11N Multi-Function Access Point EAP300 11N Multi-Function Access Point V1.0 1 Table of Contents 1 Introduction... 4 1.1 Features and Benefits...4 1.2 Package Contents...5 1.3 System Requirements...6

More information

ALL0237R. Wireless N 300Mbit Access Point/Repeater. User s Manual

ALL0237R. Wireless N 300Mbit Access Point/Repeater. User s Manual ALL0237R Wireless N 300Mbit Access Point/Repeater User s Manual ALLNET ALL0237R User Manual Table of Contents About the Device... 3 Minimum System Requirements... 5 Package Contents... 5 Device Overview...

More information

TL-WN851N 300Mbps Wireless N PCI Adapter

TL-WN851N 300Mbps Wireless N PCI Adapter Rev: 1.0.4 1910010335 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks

More information

NBG2105. User s Guide. Quick Start Guide. Wireless Mini Travel Router. Default Login Details. Version 1.00 Edition 1, 11/2012

NBG2105. User s Guide. Quick Start Guide. Wireless Mini Travel Router. Default Login Details. Version 1.00 Edition 1, 11/2012 NBG2105 Wireless Mini Travel Router Version 1.00 Edition 1, 11/2012 Quick Start Guide User s Guide LAN IP Address Default Login Details 192.168.1.1 (Router Mode) 192.168.1.2 (Other Modes) Passwordwww.zyxel.com

More information

PePWave Surf Series PePWave Surf Indoor Series: Surf 200, AP 200, AP 400

PePWave Surf Series PePWave Surf Indoor Series: Surf 200, AP 200, AP 400 PePWave Surf Series PePWave Surf Indoor Series: Surf 200, AP 200, AP 400 PePWave Surf Outdoor Series: Surf AP 200/400-X, PolePoint 400-X, Surf 400-DX User Manual Document Rev. 1.2 July 07 COPYRIGHT & TRADEMARKS

More information

WRE6505. User s Guide. Quick Start Guide. Wireless AC750 Range Extender. Default Login Details. Version 1.00 Edition 4, 12/2015

WRE6505. User s Guide. Quick Start Guide. Wireless AC750 Range Extender. Default Login Details. Version 1.00 Edition 4, 12/2015 WRE6505 Wireless AC750 Range Extender Version 1.00 Edition 4, 12/2015 2.4G 5G Quick Start Guide User s Guide Default Login Details Web Address http://zyxelsetup User Name admin www.zyxel.com Password 1234

More information

WL830RT4 Wireless G Broadband Router

WL830RT4 Wireless G Broadband Router WL830RT4 Wireless G Broadband Router User Manual VERSION 1.0 Contents About the Manual... 6 About the Router... 7 Specifications...8 Requirements...9 Device Design...9 Front Panel...9 Rear Panel...10 Getting

More information

Super G TM. Wireless Broadband Router Model # AR430W User s Manual. Ver. 1A

Super G TM. Wireless Broadband Router Model # AR430W User s Manual. Ver. 1A Super G TM Wireless Broadband Router Model # AR430W User s Manual Ver. 1A Table of Contents 1. Introduction... 3 2. Connecting the Router... 4 3. Verifying Connection to the Router... 5 4. Configuring

More information

Wireless N 300 Mini USB Adapter. Model # AWLL6086 User s Manual. Rev. 1.0

Wireless N 300 Mini USB Adapter. Model # AWLL6086 User s Manual. Rev. 1.0 Wireless N 300 Mini USB Adapter Model # AWLL6086 User s Manual Rev. 1.0 Table of Contents 1. Introduction...2 1.1 Package Contents...2 1.2 Features...2 2. Install the Wireless Adapter...3 3. Install the

More information

TD-8616B ADSL2/2+ Ethernet Modem

TD-8616B ADSL2/2+ Ethernet Modem TD-8616B ADSL2/2+ Ethernet Modem Rev: 1.0.1 1910010015 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands

More information

A Division of Cisco Systems, Inc. GHz 2.4 802.11g. Wireless-G. USB Network Adapter with RangeBooster. User Guide WIRELESS WUSB54GR. Model No.

A Division of Cisco Systems, Inc. GHz 2.4 802.11g. Wireless-G. USB Network Adapter with RangeBooster. User Guide WIRELESS WUSB54GR. Model No. A Division of Cisco Systems, Inc. GHz 2.4 802.11g WIRELESS Wireless-G USB Network Adapter with RangeBooster User Guide Model No. WUSB54GR Copyright and Trademarks Specifications are subject to change without

More information

Network Connections and Wireless Security

Network Connections and Wireless Security Network Connections and Wireless Security This chapter explains how to use your Wireless Adapter to connect to your Wireless Local Area Network (WLAN) and how to set up wireless security for the Wireless

More information

EW-7438RPn V2 User Manual

EW-7438RPn V2 User Manual EW-7438RPn V2 User Manual 09-2013 / v1.0 CONTENTS I. Product Information... 1 I-1. Package Contents... 1 I-2. System Requirements... 1 I-3. LED Status... 1 I-4. Hardware Overview... 3 I-5. Safety Information...

More information

Golden N Wireless Mini USB Adapter. Model # AWLL6075 User s Manual. Rev. 1.2

Golden N Wireless Mini USB Adapter. Model # AWLL6075 User s Manual. Rev. 1.2 Golden N Wireless Mini USB Adapter Model # AWLL6075 User s Manual Rev. 1.2 Table of Contents 1. Introduction...2 1.1 Package Contents...2 1.2 Features...2 2. Install the Wireless Adapter...3 3. Connect

More information

TD-8616 ADSL2+ Modem. Rev: 2.0.0 1910010591

TD-8616 ADSL2+ Modem. Rev: 2.0.0 1910010591 ADSL2+ Modem Rev: 2.0.0 1910010591 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names

More information

WIRELESS-N ACCESS POINT USER MANUAL

WIRELESS-N ACCESS POINT USER MANUAL WIRELESS-N ACCESS POINT USER MANUAL MODELS: 524704 524728 524735 525251 INT-524704/524728/524735/525251-UM-0214-05 Federal Communications Commission Interference Statement FCC Part 15 This equipment has

More information

TL-PS110U Single USB2.0 Port Fast Ethernet Print Server

TL-PS110U Single USB2.0 Port Fast Ethernet Print Server Single USB2.0 Port Fast Ethernet Print Server Rev: 2.0.0 1910010381 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD.

More information

Conceptronic 150N Wireless LAN Access Point User s Manual Version: 1.0

Conceptronic 150N Wireless LAN Access Point User s Manual Version: 1.0 Conceptronic 150N Wireless LAN Access Point User s Manual Version: 1.0 Contents Chapter I: Product Information 2 1-1. Product introduction 2 1-2. Safety Information 3 1-3. Package Contents 3 1-4. Familiar

More information

Chapter 3 Safeguarding Your Network

Chapter 3 Safeguarding Your Network Chapter 3 Safeguarding Your Network The RangeMax NEXT Wireless Router WNR834B provides highly effective security features which are covered in detail in this chapter. This chapter includes: Choosing Appropriate

More information