2 TABLE OF CONTENTS INTRODUCTION Control Panel...3 Detection Devices...3 Telephone Keypads...3 GLOSSARY LOCAL PHONE ACCESS Using Your Telephones As Keypads...6 LED INDICATIONS Power...7 Status...7 Home...7 Away...7 Night...7 KEYPAD FUNCTIONS Status...7 Monitor...7 F1 and F2...7 Backlight Intensity...7 ALARM SIGNALS...8 ARMING DISARMING...11 BYPASS...12 CHANGING/DELETING USER CODES PANIC FROM YOUR PHONE...13 KEYPAD ACTIVATIONS...13 RESETTING AN ACTIVATED SMOKE DETECTOR...14 REMOTE PHONE ACCESS WAY LISTEN IN...15 USER TEST...16 SETTING CLOCK TIME
3 KEYPAD AND PHONE DIGIT QUICK REFERENCE NOTE: KEYPAD AND PHONE DIGIT QUICK REFERENCE User code +1.. speaks time User code +2.. toggles monitor mode User code +3.. toggles extended monitor A on/off User code +4.. toggles extended monitor B on/off User code +5.. silences day zone speech after activation User code +6.. resets hardwire smoke detector User code +7.. auxiliary user code entry/delete mode User code +8.. speaks long term memory User code +9.. manual bypass mode User code +0.. immediate communicator test (no siren) NOTE: Only "full function" codes can perform the above operations. The DESTINY control panel provides many "convenience related" features and options that greatly enhance the system's interaction with your daily functions. Depending on your system's specific configuration, you may or may not have the following options integrated into your control panel. Enhanced features and options: automatic arming/disarming based on time of day 2-way voice with central station for alarm verification homeowner listen-in from local or remote phones homeowner global paging from local and remote phones Specialized "convenience" features and options: electric garage door operation from keypads and phones vehicle activated driveway annunciation The following 2-digit functions are only available from the RK-36 series keypads and not from phones: 1 & 3 and/or 3 & status initiate fire alarm 4 & 6 and/or 6 & monitor initiate medical alarm (inside speaker only) 7 & 9 and/or 9 & F1 initiate panic alarm 2 & 8 changes time of day in the system clock 3 & 9 programmable (default toggles monitor function) 2
4 POWER STATUS HOME AWAY MONITOR DESTINY You have made a wise decision to protect your family and property with the DESTINY Security System. The DESTINY has been designed to provide you with a maximum level of security while being as simple as possible to understand and operate. INTRODUCTION Your DESTINY Security System consists of: 1. Control panel 2. Detection devices 3. Your telephones 4. Keypad(s) CONTROL PANEL The control panel is the heart of the security system and includes a communicator which transmits information to the central station. The control panel is housed in a metal cabinet which should only be opened by a qualified security system technician. DETECTION DEVICES The detection devices continually monitor the status of the premises. Switches will alert the control panel of an open door or window. A transmitter will do the same as well as indicate when it has a weak battery. The glass break detector is exactly what the name implies: it picks up the frequency of breaking glass and instantly alerts the control panel. A motion detector is used as a second line of defense to detect intruders within a protected area. The smoke detector is always on. SWITCHES TRANSMITTER GLASS BREAK DETECTOR MOTION DETECTOR SMOKE DETECTOR TELEPHONE KEYPADS Your phones and keypads are used to send commands to your security system. Because your phones and keypads are your access to operating the security system, the main emphasis of this user s manual is to help you understand their operation. Before reading this manual, it is recommended that you become familiar with the terms and definitions in the Glossary STATUS F1 A 0 H F2 3
5 GLOSSARY ALERT ANNUNCIATION ARM AWAY BYPASS CENTRAL STATION COMMUNICATOR CONTROL PANEL DISARM DISARM CODE ENTRANCE DELAY GLOSSARY ALERT - The "alert" status indicates the system has been tripped. The system will remember the "alert" status until cleared. To clear the "alert" status, simply re-arm the panel. ANNUNCIATION - Beep or speech emitted over the phone or through system speakers to announce activity or report system status. ARM - To turn the security system ON to detect intrusion. There are three modes, or levels, of arming: AWAY, HOME or NIGHT. AWAY - Arming mode for use when you are AWAY from the premises. All interior and perimeter devices are armed; intrusion and/or movement within the premises will activate the alarm. BYPASS - To temporarily remove a zone from the system that would normally be active when the system is armed. If a zone is bypassed, it is not part of the system, and will not initiate an alarm. CENTRAL STATION - If your security system is monitored, this is the agency that receives the incoming burglary or emergency message from the security system and reports it to the proper authorities. COMMUNICATOR - The device in the control panel that reports all burglary and emergency alarms to the central station via telephone lines. CONTROL PANEL - The heart of the security system. Only a qualified security system technician should open the container which houses the control panel. DISARM - To turn the security system OFF or silence alarm activations, including fire alarms, that may occur while the system is armed. DISARM CODE - The three or four digit number you enter to disarm the security system. The system will accept 8 different disarm codes, including disappearing and duress codes. ENTRANCE DELAY - Time permitted to enter the armed premises and disarm the security system before the alarm is activated. A 20 second delay is set at the factory, but your installer can program a longer or shorter time, as desired. 4
6 EXIT DELAY - Time permitted to leave the premises after arming the system. A 30 second delay is set at the factory, but your installer can program a longer or shorter time, as desired. EXTENDED MONITOR - Allows a zone to speak continuously or for a programmable time period when tripped. Example would be "pool door open, pool door open,..." FORCE ARM - To override the security system's initial refusal to arm because of an open zone. When the system is force armed it will disregard any open zones until they have been closed. HOME - Arming mode for use when you are at HOME. Only perimeter devices are armed allowing you to move about freely within the premises. The system will be programmed to eliminate all entrance delays when armed to home. This might be preferable for individuals living alone. INTERIOR ZONES - Zones consisting of motion detectors or any other detection devices located within the premises. LED - Light emitting diode. These are used as indicators of system conditions on keypads. NIGHT - Arming mode for use when everyone is in for the NIGHT. All perimeter devices become instant and some interior zones can be active. PERIMETER ZONES - Zones consisting of door and window contacts and glass break detectors which will detect an intruder before he gains entry into the premises. PREALARM SPEECH - When the system is armed, and someone enters the premises through a "delay" door, the system speaks "entry detected" followed by the word description programmed for that door. Example: "entry detected, front door...entry detected, front door." This speech will be heard for the duration of the entrance delay. If the disarm code is not entered within the programmed time, the BURGLAR ALARM will sound. If an alarm took place while you were gone, then the system would speak "system showing alert," followed by the prealarm speech. PREALARM TONE - Steady, low volume sound emitted through the speakers when the entry delay door is opened. This tone will continue until the disarm code is entered to disarm the system. If the disarm code is not entered within the programmed time, the BURGLAR ALARM will sound. A pulsing prealarm tone indicates there was an activation while you were gone. ZONE - Any area or point of protection in the security system such as doors, windows, and all other areas covered by detection devices. GLOSSARY, cont. EXIT DELAY EXT. MONITOR FORCE ARM HOME INTERIOR ZONES LCD LED NIGHT PERIMETER ZONES PREALARM SPEECH PREALARM TONE ZONE 5
7 USING YOUR TELEPHONES AS KEYPADS NOTE: NOTE: LOCAL PHONE ACCESS USING YOUR TELEPHONES AS KEYPADS The system can be programmed to allow the use of your home telephones as keypads. You will notice that the keypad shown below duplicates the keys on your phone. The * key on the phone is replaced by the A key on the keypad and the # key on the phone is replaced by the H key on the keypad. Your installer will let you know which key or keys will access the system. The local phone access code must be entered within (5) seconds of picking up the phone. If the correct code is entered within (5) seconds, you will hear the system acknowledgement tone or system status. At this point you can control the system from the phone just like from the hardwired keypad. NOTE: If your regular phone line is out for any reason you will not hear a dial tone when you pick up a phone, however, you will hear a series of tones indicating the line is gone. If this is the case, there is no need to access the system because the phone will already be a system keypad when it is picked up. Press any key and the tones will stop. If your system communicates to a central station and there is an activation, you can pick up a phone and simply enter your disarm code. The system will recognize the phone as a keypad as soon as you pick it up. NOTE: When you access the system from your home phone, your normal incoming phone line is disconnected. In the case of an incoming call you will hear one-second tones similar to call waiting. To answer the call simply hang up to terminate telephone keypad access. POWER HOME STATUS AWAY STATUS MONITOR F1 A 0 H F2 RK36 KEYPAD MONITOR MODE FROM A PHONE 6 MONITOR MODE FROM A PHONE See RK36 Keypad description for explanation of "Monitor Mode." To change monitor mode from a phone; access the system (refer to Local Access or Remote Access), then enter the user code plus the 2 digit. This toggles to the monitor mode.
8 RK36 KEYPAD - LED's and SPECIAL KEYS POWER On when AC or back-up battery power is present. If AC power is lost the POWER LED will turn off and the STATUS LED will flash, and the system will speak "POWER OFF" one time. STATUS Flashing when new information is available, solid after status has been asked for and spoken, and off when no information is present. HOME On when armed to HOME. Press H to arm to HOME. AWAY On when armed to AWAY. Press A to arm to AWAY. NIGHT Both HOME and AWAY LED's are on when armed to NIGHT. Press H any time system is armed to HOME to change to NIGHT. Pressing H when system is armed to NIGHT will change arming back to HOME. STATUS Pressing this key will cause the system to immediately speak system status. MONITOR Pressing this key toggles the system between the three possible monitor conditions. Monitor On - System will announce doors and windows when opened. Monitor Off - System will not announce doors and windows when opened. Beep - System will beep when doors and windows are opened. F1 and F2 These key's functions are programmable and will be explained by your installer. F1 F2 BACKLIGHT INTENSITY You can control the brightness level of the key backlighting. The simultaneous depression of the 4 and 7 keys will step the backlighting through 7 different levels. Press 4 and 7 simultaneously a number of times until the backlighting is totally off. We will define all backlighting off as level 1. Levels 2 through 7 will take the key backlighting through 6 progressively brighter levels. RK36 KEYPAD GREEN POWER YELLOW STATUS RED HOME GREEN AWAY STATUS MONITOR F1 F2 7
9 ALARM SIGNALS ALARM SIGNALS Understanding the alarm signals: FIRE Alarm: a loud pulsing, steady, loud pulsing tone emitted through the speakers. Your installer may also program the system to speak in between tones saying FIRE, FIRE (description of zone that activated), REMAIN CALM, LEAVE IMMEDIATELY. EMERGENCY Alarm: a low pulsing tone is emitted through the speakers. Your installer may also program the system to speak in between tones saying ALERT, (description of zone that activated). PANIC Alarm: a loud pulsing tone is emitted through the speakers. Your installer may also program the system to speak in between tones saying ALERT, ALERT, (description of zone that activated). BURGLAR Alarm: a loud yelping tone is emitted through the speakers. Your installer may also program the system to speak in between tones saying INTRUSION DETECTED, INTRUSION DETECTED (description of the zone that activated). PREALARM tone: a steady, low volume tone emitted through the speakers during the entrance delay. This tone is activated by opening the delay door and will continue until the security system is disarmed. If the system is not disarmed within the programmed delay time, the BUR- GLAR alarm will sound. A broken or pulsing prealarm tone signals that an alarm activation has occurred while you were gone. If the option is programmed to speak during prealarm, the system will speak entry detected, followed by the zone descriptor, instead of a solid prealarm tone. DOOR & WINDOW ANNUNCIATOR: The system will speak up to four words describing a zone followed by the word OPEN. If you would prefer not to hear anything when you open a window or door, simply access the system from one of your phones and press your code followed by 2 or press the MONITOR key at an optional keypad and you will hear MONITOR OFF. Now each time you open a protected door or window there will be status available over the phone and/or visual indication at the keypad, but no sound. If you prefer to hear a beep when you open, enter your code followed by 2 or press the MONITOR key again. You will now hear "MONITOR TONE". Enter your code followed by 2 or press the MONITOR key and you will hear MONITOR ON and the system will return to speech. No monitor will be heard for a door or window that is bypassed. 8 Loss of AC power signal: Anytime that you lose AC power, your security system automatically switches to the backup battery and speaks POWER OFF one time through the speaker.
10 ARMING ARMING When referring to operation from a phone, the following instructions will assume that access to the system has already taken place. Remember, your installer has programmed a one to four digit code which you will enter when you pick up the phone to get access to the system. How to TURN ON the alarm system to provide protection: 1. Arming the system to AWAY: Push the * or A key. If no zones are open, the green AWAY LED will light and the system will say ARMED TO AWAY over the phone or through the speaker. ARMING THE SYSTEM TO AWAY: PUSH THE * OR A KEY. The security system is now on, or armed. When armed in the AWAY mode, all interior zones, including motion detectors, become active, as well as all perimeter zones. If any zone is open while attempting to arm the system, the AWAY LED will not light and the system will say ZONES OPEN over the phone or through the speaker, indicating that the system did NOT arm because a window or door is OPEN. See Force Arm to continue to arm. After you have ARMED the system, you must leave through the designated entry/exit door within the specified exit delay time. Your installer can program the exit delay time you desire. NOTE: If a zone is opened before the exit delay expires, or the system is force armed, then that zone will not be part of the system until that zone is closed. 2. Arming the system to HOME: Push the # or H key. If no zones are open, the red HOME LED will light and you will hear the system say ARMED TO HOME over the phone or through the speaker. NOTE: ARMING THE SYSTEM TO HOME: PUSH THE # OR H KEY. The security system is now on, or armed. When armed to the HOME mode, only the exterior, or perimeter, zones are armed. This will allow you to move about freely within your home. If any zone is open while attempting to arm the system, the HOME 9
11 ARMING ARMING THE SYSTEM TO NIGHT:(OPTIONAL) PUSH THE # OR H KEY AGAIN. LED will not light and you will hear the system say ZONES OPEN over the phone or through the speaker which indicates that the system did NOT arm. See "Force Arming" to continue. 3. Arming the system to NIGHT: (Optional) Arm the system to HOME mode. (See item 2) Push the # or H key again. The green AWAY LED will light with the red HOME LED and the system will say ARMED TO NIGHT over the phone and/or through the speaker. When armed to the NIGHT mode, the perimeter entry delay zones become instant and your installer may program some interior zones to be active. If you wish to return to the HOME mode, simply push the # or H key any time the system is in the NIGHT mode. FORCE ARMING THE SYSTEM: 4. Force Arming the system: If you attempt to arm the system to either HOME or AWAY but you hear ZONES OPEN over the phone and/or through the speaker and notice that neither the HOME LED nor the AWAY LED has come on, the system is NOT armed. However, the system can be FORCE ARMED. Push the # or H or * or A key a second time within 10 seconds. If arming to HOME, the red HOME LED will now light and FORCE ARMED TO HOME will be heard indicating that the system is now ARMED to HOME. If arming to AWAY, the green AWAY LED will now light and FORCE ARMED TO AWAY will be heard. When FORCE ARMED either to HOME or AWAY, the yellow STATUS LED will be lit. You can find out which zones are open by requesting system status. PLEASE NOTE: PLEASE NOTE: When you FORCE ARM your system, security is compromised because the open zone will be ignored by the system. Check with your installer to determine how the open zone will again be part of the system. Zones which operate 24 hours a day such as FIRE and PANIC are always armed and take priority over all other types of protection in the system. 10
12 5. Preventing accidental arming: If you want to prevent anyone from accidentally arming the system, your installer can program the alarm system to require your disarm code to also serve as an arming code. When programmed to this option, you must enter your code before you press the * or A key (AWAY mode) or # or H key (HOME mode) to arm the system. DISARMING How to TURN OFF the alarm system ARMING, cont. PREVENTING ACCIDENTAL ARMING: DISARMING Enter your disarm code. When the system is disarmed, you will hear CON- TROL IS DISARMED over the phone and/or through the speaker and the red HOME LED and/or green AWAY LED will go out. When you open the entry door while the system is armed to AWAY, you may hear PRE-ALARM spoken instead of hearing the tone. This is the prealarm tone and it will continue until you enter your disarm code. You have 20 seconds to disarm the system before the BURGLAR alarm will activate. Your installer can program a longer or shorter entry delay time, at your request. If the prealarm tone is not a continuous, steady tone, but is instead a series of broken tones, this is an indication that the security system was activated while you were gone, and the yellow STATUS LED will be flashing. In the unlikely event of a FALSE or ACCIDEN- TAL ALARM, enter your code to disarm the system and stop the audible alarms. Check with your installer and/or central station to determine the proper procedure for dealing with false or accidental alarms. Depending on the structure of your central station, you may need to notify the central station or they may call you. In either event, be prepared to recite your central station account number or abort code to verify your identity. 11
13 BYPASS BYPASS To enter BYPASS mode, your system must be disarmed. Make sure the system is disarmed and follow the steps below: 1. Enter your code and immediately press the 9 key to gain entry into BYPASS mode. You will hear BYPASSED MODE, ENTER ZONE NUMBER. 2. Enter the two digit number of the zone (use a leading zero if necessary) you wish to bypass. You will hear (description of selected zone) BYPASSED (ON or OFF). Only zones that exist in the system can be bypassed. If an invalid zone number is entered, refusal will be signaled by three beeps. 3. Press the * or A key. The yellow STATUS LED will light to indicate that the zone is bypassed. A second push of the * or A key within 10 seconds will remove the zone from bypass and the yellow STATUS LED will clear. 4. Pressing 00 while in BYPASS mode will clear all bypassed zones. 5. Press the # or H key to exit BYPASS mode. You will hear EXIT. NOTE: NOTE: If ten seconds pass without pressing any keys, the system will automatically exit BYPASS mode. CHANGING/DELETING USER CODES Assuming your primary code is 1,2,3,4: 1. Enter 1, 2, 3, 4, The system will speak ENTER USER NUMBER. 3. Enter 2 digit user number, (01-08). The system will speak "ENTER CODE X X" (X X = 01-08). You do not need to clear a code to change a code. 4. Enter the new 4 digit code or hit the A key to delete the user code from step 3. If a new 4 digit code is entered the system will speak EXIT after the 4th digit. If a code is deleted the system will speak CODE OUT. 12
14 POWER STATUS HOME AWAY MONITOR The DESTINY allows 8 different disarm codes. Check with your installer to find out how many codes are enabled. To enter or change an auxiliary code; 1. Enter your primary disarm code. 2. Follow steps 2 through 4 above, however, in step 3 instead of entering 01 you will enter the two digit number of the code you wish to initiate or change. One or more of your auxiliary codes can be a disappearing code which is useful for domestic workers, repairmen or anyone whose access to your home you want to limit. Your installer can program the number of times a disappearing code will remain active each time it is assigned. One or more of your auxiliary codes can be used as a duress code. Your installer can program your system so that the use of a duress code will give the appearance of being a normal disarming code. However, even though no alarm is sounded at the location of the security system, there will be a silent alarm signal sent to the central station. For the duress code to function as designated, no normal codes can be the same as any duress code. PANIC FROM YOUR PHONE Anytime you have accessed your system from an on-site phone, pressing the 0 key five times in a row will initiate a PANIC alarm. PANIC FROM YOUR PHONE NOTE: Never program a disarm code with all zeroes. KEYPAD ACTIVATIONS Simultaneously pressing certain keys on the keypad will result in the following: KEYPAD ACTIVATIONS 3 and STATUS - FIRE Alarm 6 and MONITOR - EMERGENCY Alarm STATUS 9 and F1 - PANIC Alarm F1 A 0 H F2 MONITOR -Door & Window annunciator ON with beep, ON with speech or OFF 13
15 RESETTING AN ACTIVATED SMOKE DETECTOR REMOTE PHONE ACCESS RESETTING AN ACTIVATED SMOKE DETECTOR Whenever any of your wired (non-battery powered) smoke detectors activate the system, they will latch ON until you reset them. To do so, enter your primary code followed by 6. The system will say SMOKE POWER. REMOTE PHONE ACCESS You can gain access to the system from any touch-tone phone when you are away from home. If you use an answering machine, your installer will program an override digit which you will use to bypass the answering machine and get directly into the system. Following is a step-by-step description of phone access: 1. Dial your home number from any touch-tone phone. 2. The system will answer after a programmed number of rings and you will hear an acknowledgment tone that your system is ready and waiting. If you have an answering machine, wait for it to answer, then press the programmed override digit within 10 seconds and you will then hear the acknowledgment tone indicating that your system is ready and waiting. 3. You must now enter your disarm code and the system will speak your system status. If you do not enter an acceptable code within 5 seconds of the tone you heard in Step 2, the system will automatically hang up. 4. Now that you have entered your code and have received the system status, your telephone can be used as a keypad. To hear the status of your system again, press the first digit of your disarm code and wait three seconds. The system status will be repeated through your telephone receiver. To disarm the system over the phone, simply enter your disarm code on the telephone keypad. To arm the system, use the * key to arm to AWAY or use the # key to arm to HOME. Once you have finished, simply hang up the phone and the system will hang up at the other end. If you do not press any digits for a period of 15 seconds, the system will automatically hang up. NOTE: 14 NOTE: Your installer can increase or decrease this time.
16 2 WAY AND LISTEN IN: 1. Access the system (see Local Access or Remote Access) 2. Press 9,9,9,9 to enter "Listen" mode. 3. Press # to talk, * to listen. 4. Hang up when done or press 0 to return to keypad mode. OPTIONAL EQUIPMENT 2 WAY AND LISTEN IN NOTE: When in 2 way mode, the following key functions apply: Digit: 1 = turns on microphone #1 2 = turns on microphone #2 3 = turns on microphone #3 4 = turns off microphone #1 5 = turns off microphone #2 6 = turns off microphone #3 7 = changes to "high microphone sensitivity" 8 = changes to "normal microphone sensitivity" 9 = all microphones on 0 = Exit to keypad mode/or will hang up (programming option) * = Listen # = Talk NOTE: Some central stations may designate other key functions when in 2 way mode. If this is the case, the homeowner "listen in" will follow the new key assignments. New Digit: 1= 4= 7= 0= 2= 5= 8= *= 3= 6= 9= #= 15
17 NOTE: User Test Mode A user Communicator test is integrated into the system to allow an end user to test the system on a regular basis. Enter a valid user code followed by the "0" digit. The system will speak "Enter User Test Mode." A User Communicator Test report is sent to the central station. WHILE IN TEST MODE THE SYSTEM CEASES TO BE A SECURITY SYSTEM. As each zone is tripped (including 24 hour zones) the system will speak the zone description followed by "active." After 3 mintues (programmable) the panel will automatically exit user test mode. To exit user test mode manually, enter a user code followed by the "0" digit. User Test Timeout Controls the amount of time before the User Test Mode will automatically time out. CHANGING THE CLOCK TIME To set or change the system time, press the 2 & 8 keys simultaneously from a hardwired keypad. The system will respond by speaking "enter four-digit time." Simply enter the time in a 12- hour format. After the time is entered, the system will say "enter (1) AM, (2) PM." After selecting AM or PM, the system will confirm the entered time. Enter day of the week after the system prompts "for Sunday enter (1), for Monday enter (2), for Tuesday enter (3), for Wednesday enter (4), for Thursday enter (5), for Friday enter (6), for Saturday enter (7)." System will say "enter (2) digit month." After entering date, system will say "enter (2) digit year." If an invalid entry is made, the system will speak "error" and wait for a valid entry. 16
DESTINY OWNER S MANUAL DESTINY You have made a wise decision to protect your family and property with the DESTINY Security System. The DESTINY has been designed to provide you with a maximum level of security
DESTINY TABLE OF CONTENTS KEYPAD AND PHONE DIGIT QUICK REFERENCE NOTE: KEYPAD AND PHONE DIGIT QUICK REFERENCE POWER STATUS HOME AWAY MONITOR DESTINY INTRODUCTION CONTROL PANEL DETECTION DEVICES SWITCHES
SECURITY SYSTEM NOTES Installing/Service Company For Service Call Central Station Duress Code FUNCTION CODES Function Code Controls Function This system is is not partitioned. EMERGENCY ACTIVATION KEYS
SECURITY SYSTEM NOTES Installing/Service Company For Service Call Installation Date / / Central Station Duress Code EMERGENCY ACTIVATION KEYS (check if enabled) Fire Auxiliary Emergency Police PROGRAMMED
NetworX NX-6V2 LED Keypad User Manual POWER Light is on when AC power is present; flashes to indicate a low battery condition. ARMED Light is on when armed; off when disarmed; flashes to indicate a previous
TABLE OF CONTENTS...Glossary of terms...2...code Pad Diagram...3 Understanding the Code Pad lights...4 Code Pad tones...5 Fully arming the system On MODE...6 Fully arming the system - Quick Arm MODE...6
Using your LED Plus keypad System 238 System 2316 System 238i System 2316i Part Number 5-051-372-00 Rev B Thank you for purchasing this C&K alarm system Your system is one of the most powerful and advanced
Users Guide to Keypad Functions MANUAL NO. 700-175-01J ISSUED JAN 2002 VERSION 1.41 Summary of Operation A rm/ disarm [#] + [USER CODE] Quick Quick Quick Panic Fire Medical Away Arm Stay Arm Stay Arm &
FIRST ALERT INSTRUCTION MANUAL FOR FA 270 KEYPADS SECURITY SYSTEM Page 0 Table of Contents Introduction 1 System Basics.. 1 Burglary Protection.. 1 Fire Protection.. 1 Security Codes. 1 Zones and Partitions
INHEP DIGITAL IDS S E C U R I T Y Users Guide to Keypad Functions MANUAL NO. 700-171-01B ISSUED AUG 2002 VERSION 1.18 Summary of Operation A rm/ disarm [#] + [USER CODE] Quick Quick Quick Away Arm Stay
1 2 Contents 1. Introduction to the IDS X-Series Panels... 7 2. Before Operating Your Alarm System... 7 3. Understanding the Keypad LEDs... 8 3.1 Viewing Data on an LED Keypad... 12 3.1.1 LED Status Indicators...
5HDG\*XDUG5 6HFXULW\6\VWHP OFF AWAY STAY AUX 8VHU*XLGH K5481-1 8/00 7$%/(2)&217(176 SYSTEM OVERVIEW...3 Features...3 General Operation...4 Quick View of System Functions...6 About the Master Keypad...7
HILLS Series LED Code Pad User Manual Not all features may be available on your system Check with your installer to find out which features are programmed Page 2 TABLE OF CONTENTS Code Pad Diagrams...2
ADEMCO VISTA SERIES VISTA-20P / VISTA-20PSIA VISTA-15P / VISTA-15PSIA Security Systems User Guide K5309-1V4 10/04 Rev. A IMPORTANT! PROPER INTRUSION PROTECTION For proper intrusion coverage, sensors should
VISTA-128FBP VISTA-250FBP Commercial Fire and Burglary Partitioned Security Systems with Scheduling User Guide K0377V2 7/09 Rev. C 2 TABLE OF CONTENTS SYSTEM OVERVIEW... 5 General... 5 A Partitioned System...
Lynx Plus Series Security System User Guide ARMED READY ESCAPE ADD OFF AWAY RECORD LIGHTS ON 1 2 3 VOLUME TEST PLAY 4 5 6 BYPASS 7 8 9 STAY DELETE AUX SELECT LIGHTS OFF 0 CODE CHIME STATUS NO DELAY FUNCTION
ADEMCO VISTA SERIES VISTA-20P / VISTA-20PSIA VISTA-15P / VISTA-15PSIA Security Systems User Guide K5309-1V7 3/15 Rev A IMPORTANT! PROPER INTRUSION PROTECTION For proper intrusion coverage, sensors should
S e c u r i t y S y s t e m User's Manual VISTA-50P VISTA-50PUL N5943-6 7/95 TABLE OF CONTENTS SYSTEM OVERVIEW... 3 A Partitioned System... 3 Zones... 3 Fire Protection... 4 Burglary Protection... 4 Alarms...
Solution-16 Operators Manual ISSUE 1.60 !"#$%&"'()*+ Operators Manual Copyright 2002 by, SYDNEY, AUSTRALIA Document Part Number MA880O DOCUMENT ISSUE 1.60 Printed 22 March 2002 This documentation is provided
HILLS Series LED Code Pad User Manual Not all features may be available on your system Check with your installer to find out which features are programmed Page 2 TABLE OF CONTENTS Code Pad Diagrams...2
National Security Systems Inc (800)457-1999 Security System User's Guide Security System Glossary As security system technology has evolved, a special jargon has developed. Some terms widely used within
LYNX Touch L5210 Series Security System User Guide 800-19975 12/14 Rev. A LYNX Touch L5210 Series Your Honeywell security system is designed for use with devices manufactured or approved by Honeywell for
Installing / Service Company: For Service Call: SECURITY SYSTEM NOTES Security System Configuration Master Code: Auxiliary Code(s) 2 3 4 5 6 "Quick Arm" Digit: Exit Delay Time Auxiliary Exit Delay Time
LYNX Touch L7000 Series Security System User Guide 800-16084 12/13 Rev. A LYNX Touch L7000 Series Your Honeywell security system is designed for use with devices manufactured or approved by Honeywell for
LYNX Touch Security System User Guide 1:35 2 PM October 26, 2011 72 Mostly Sunny 68 F F Feels Like 71 Security Messages Automation 5-Day Forecast News Traffic 800-10615 1/12 Rev. A LYNX Touch L5100 Series
LYNX Touch L5200 Series Security System User Guide 800-16083V1 12/14 Rev. A LYNX Touch L5200 Series Your Honeywell security system is designed for use with devices manufactured or approved by Honeywell
Pi-8 USER MANUAL CONTENTS 1. THE KEYPAD AND ITS OPERATION...3 1.1 DESCRIPTION OF THE KEYPAD LEDS... 3 1.1.1 READY LED (RED)...3 1.1.2 TAMPER LED (RED)...3 1.1.3 POWER LED (GREEN)...3 1.1.4 CIRCUIT LEDs
SCORPION 4120 6020 & 8020 USER INSTRUCTIONS Thank you for purchasing a Quality Micron Security Alarm Controller. Micron product is manufactured to exacting quality standards. We understand the importance
ARMED READY OFF AWAY STAY MAX TEST BYPASS INSTANT CODE CHIME READY ARMED READY NIGHT NO AC PHONE TEST NOT READY CHIME BAT CHECK INSTANT CANCELED OFF AWAY STAY MAX TEST BYPASS INSTANT CODE CHIME READY 3
ADEMCO LYNXR-EN Security System User Guide ARMED READY OFF ESCAPE AWAY ADD STAY RECORD LIGHTS ON 1 2 3 VOLUME 4 5 6 TEST 7 8 9 PLAY BYPASS DELETE AUX SELECT LIGHTS OFF CODE CHIME 0 # STATUS NO DELAY FUNCTION
GC2 Panel User Guide ENGLISH (International) WIRELESS SECURITY SYSTEM WARNING: OWNER S I NSTRUCTION NOTICE Not to be removed by anyone except occupant THIS PAGE INTENTIONALLY LEFT BLANK CONTENTS System
LYNX Touch Security System User Guide 800-10615V1 12/12 Rev. A LYNX Touch L5100 Series Your Honeywell security system is designed for use with devices manufactured or approved by Honeywell for use with
User s Guide Security Systems D220 Table of Contents About This User s Guide... 3 Introduction... 3 Security System Basics... 4 Controlled Points... 5 24-Hour Points... 6 Keypad Keys... 6 Keypad Lights...
VISTA-100 Commercial Fire and Burglary Partitioned Security System 8VHU*XLGH FIRE FIRE * PULL N6020-2 Rev B 4/99 TABLE OF CONTENTS SYSTEM OVERVIEW... 3 A Partitioned System... 3 Zones... 3 Fire Protection...
9,67$39,67$3&1 9,67$39,67$3&1 6HFXULW\6\VWHPV 8VHU V*XLGH K5309-1V1 8/01 1 IMPORTANT! PROPER INTRUSION PROTECTION For proper intrusion coverage, sensors should be located at every possible point of entry
Elite 8D/Lite Version 8 Zone Controller 8 Arrowhead Alarm Products Ltd Operating Guide 1 Proudly Designed and Manufactured in New Zealand 2 CONTENTS Page No. INTRODUCTION 4 About your Alarm 4 OPERATING
Index Arming Your System...page 1 Chime Feature...page 4 Access Codes...page 4 Setting the Time and Date...page 5 Adjusting the Keypad Display/Volume...page 6 Panic Alarms...page 7 Testing Your System...page
GE Concord 4 Quick User Guide GE Concord 4 Quick User Guide Page 1 Before Calling Is the keypad beeping? Press *. This will silence the beeping and let you know where the trouble is. Is there a flashing
POWER POWER POWER ABC DEF GHI JKL ABC DEF GHI JKL MNO PQR STU VWX MNO PQR STU VWX YZ COMMAND YZ COMMAND ABC DEF GHI JKL MNO PQR STU VWX COMMAND YZ USER'S GUIDE Security Command User's Guide for 9XR Command
Solution 880 Operators Manual ISSUE 1.10 Solution 880 Operators Manual Copyright 2001 by, SYDNEY, AUSTRALIA Document Part Number MA408O DOCUMENT ISSUE 1.10 Printed 25 May 2001 This documentation is provided
MODEL 4734 SECURITY SYSTEM OWNER'S MANUAL TABLE OF CONTENTS 1 SYSTEM OVERVIEW Page 1 1.1 Introduction 1 1.2 System components 1 1.3 Features 3 1.4 Types of alarms 5 1.5 Other audible signals 6 1.6 Access
Using Your Security System With Icon Keypad S5020, S5021, S5022 Contents 1 Overview Your Security System... 1 How Your Security System Works... 2 Your System's Programming... 3 Getting Used to Your System...
HSC505-R Home Security Controller - User Manual Release R1a Pi HSC505 and Pi HSC505R Home Security Controller User s Information Guide R1A Page 1 QD Dynamics (Pty) Ltd reserves the right to make changes
DS7060 User Guide Copyright 1996-97 Detection Systems, Inc. User Guide for the DS7060 Control/Communicator Copyright 1996-97 Detection Systems, Inc. Detection Systems, Inc., 130 Perinton Parkway, Fairport,
tattletale User Guide Consumer unit version 2.48 1 P a g e Contents Basic 1... 4 Base Unit Features... 4 Initial Setup... 4 Arming... 5 Disarming... 5 Quiet Button... 5 Settings... 5 Settings 2... 6 Quick
SECURITY SYSTEM NOTES Installing/Service Company For Service Call SPECIAL CODES "Chime" Digit 1 "Partial Arm" Digit 2 "Quick Arm" Digit 3 ENTRY / EXIT DELAY TIMES Exit Delay Time Entry Delay Time Secondary
Security System Owner s Manual Interactive Technologies Inc. 2266 North 2nd Street North St. Paul, MN 55109 FCC Notices FCC Part 15 Information to the User Changes or modifications not expressly approved
D1260/D1260B EN Owner's Manual Keypad National Security Systems Inc (800)457-1999 D1260/D1260B Owner's Manual This system includes a telephone line seizure feature. The system may be programmed to communicate
ICP-CC488 EN User s Guide ICP-CC488 Control Panel ICP-CC488 User's Guide Notices EN 2 Copyright Notice Unless otherwise indicated, this publication is the copyright of Bosch Security Systems, Inc. ( Bosch
SCORPION Z16040C Alarm Controller User Instructions Thank you for choosing to purchase this micron security alarm controller. Micron product is manufactured to exacting quality standards. We understand
Fire and Burglary System User's Manual 5120XM N8031 6/96 SYSTEM OVERVIEW...3 General...3 Zones...3 Fire & Emergency Protection...3 Burglary Protection...4 Alarms...4 Memory of Alarm...4 ABOUT THE KEYPADS...5
Security System User's Guide Security System Glossary As security system technology has evolved, a special jargon has developed. Some terms widely used within the industry are these: Arm and Disarm Your
ELECTRONIC ENGINEERING LTD. PowerWave-8 8 zone Control panel Communicator Users Operating and Programming Guide Version 8.64 P/N 7101261 Rev. C N.A July 2002 2 Contents Introduction...5 Meet the Crow Alarm
Wireless Security System 2GIG-CNTRL2 (2GIG-CP2) User s Guide WARNING: Owner s Instruction Notice Not to be removed by anyone except occupant The Go!Control Security System Congratulations on your ownership
Using Your Security System With LED Keypad S5030, S5031, S5032 Contents 1 Overview Your Security System... 1 How Your Security System Works... 2 Your System's Programming... 3 Getting Used to Your System...
User's Manual For use with ProSYS 16, ProSYS 40, and ProSYS 128 Important Notice This manual is delivered subject to the following conditions and restrictions: This manual contains proprietary information
Concord 4 User Manual P/N 466-2183 REV NOV12 Copyright Disclaimer 2012 UTC Fire & Security Americas Corporation, Inc. Interlogix is part of UTC Climate Controls & Security, a unit of United Technologies
TABLE OF CONTENTS HOW TO AVOID FALSE ALARMS... 1 THE BRINK S HOME SECURITY SYSTEM Equipment in the Standard Systems... 2 Optional Equipment... 3 Description of the Keypad... 5 OPERATING THE BRINK S SYSTEM
Simon XTi Quick Operation Guide This is the Quick Operation Guide for the Simon XTi system (models 600-1054-95R-12 & 600-1054-95R-12-CN). The Simon XTi provides a graphical user interface for programming
FA701 Series TouchCenter Keypads User s Guide K6249-2V2 5/09 Rev. A Table of Contents ABOUT THE TOUCHCENTER... 5 Introduction... 5 2 The TouchCenter Interface... 5 Navigating through the TouchCenter...
VR8 EN User Guide Intruder Alarm System VR8 User Guide Notices EN 2 Copyright Notice Unless otherwise indicated, this publication is the copyright of Bosch Security Systems Pty Ltd ( Bosch ). All rights
infinite prime User Manual - Version 3.00 Catalog Number: 5IN1912 All data is subject to change without prior notice. Hereby, Electronics Line 3000 Ltd. declares that this control panel is in compliance
NESS D16 16 Zone Control Panel and Dialler OWNER S MANUAL REVISION 2, JULY 2001 Ness Security Products Pty Ltd Quality Endorsed Company ISO9001 LIC.No. QEC2074 NSW Head Office only WWW.NESS.COM.AU Australia
SECURITY AND HOME AUTOMATION OWNER S MANUAL 466-1040-01-ITI Rev. F (Text) Contents Welcome.......................... viii Section 1: Working with Your New Security System..................... 1 What You
GE Security Simon XT V2 User Manual P/N 466-2266-01 REV A ISS 24FEB10 Copyright Disclaimer Trademarks and patents 2010 GE Security, Inc. This document may not be copied in whole or in part or otherwise
Security System User Guide for the LED Command Center MY SECURITY COMPANY IS: CALL BEFORE TEST: THIS SECURITY SYSTEM IS CONNECTED TO TELEPHONE NUMBER: THE SECURITY CONTROL PANEL IS CONNECTED TO THE PHONE
User s Guide Security Systems National Security Systems Inc (800)457-1999 2 Table of Contents About This Users Guide... 4 Introduction... 4 Security System Basics... 5 Controlled Points... 6 24-Hour Points...
User s Guide Security Systems 2 Table of Contents About This Users Guide... 4 Introduction... 4 Security System Basics... 5 Controlled Points... 6 24-Hour Points... 7 Keypad Keys... 7 Keypad Tones... 8
i 1 6-4 ) 6 1 ) + + 4, 7 IA HI/ K E@ A 6 Document No. 466-1763 Rev. D ii Commands at a Glance Disarm the system. Cancel an accidental alarm. Arm to Level 2 HOME. Arm to Level 3 AWAY. Send a police alarm.
MONITOR ISM / AFx Multi-Tenant Security System User Guide V.3 Multi-Tenant Security System User Guide Welcome New Users! There are two types of suite security keypads. Follow the instructions in the proceeding
ICP-CC488 EN Installation Guide ICP-CC488 Control Panel ICP-CC488 Installation Guide Notices EN 2 Copyright Notice Unless otherwise indicated, this publication is the copyright of Bosch Security Systems,
MODEL CA100 REMOTE CONTROL AUTO ALARM SYSTEM INSTALLATION & OPERATION INSTRUCTIONS WIRING DIAGRAM Black Antenna Wire 6 Pin 6 Pin Mini Connector Valet Switch Blue LED Indicator Blue Wire: (-) 200mA Unlock
) *(6HFXULW\ 466-1936 Rev E October 2004 ZZZ*(6HFXULW\FRP Part No: 60-883-95R CareGard User Guide FCC Notices FCC Part 15 Information to the User Changes or modifications not expressly approved by GE Security
Your consent to our cookies if you continue to use this website.