MALAVIYA NATIONAL INSTITUTE OF TECHNOLOGY JAIPUR

Transcription

1 MALAVIYA NATIONAL INSTITUTE OF TECHNOLOGY JAIPUR No. F5(189)ST/MNIT/Com.Eng./2015 Phone : , M/s NOTICE INVITING QUOTATIONS Fax No. : Registrar, MNIT, Jaipur invites sealed QUOTATIONS for the supply of Equipment/Goods for Computer Engineering Department of this Institute in two bid system (Technical & Financial bids separate envelop), as per schedule given below: Event Date & Time Download of Tender Bid submission by 2.00 PM Technical bid opening at 3.00 PM Financial bid opening Will be intimated Latter Tender Fees Rs.1,000/- Only Earnest Money 2% of the Quoted amount 2. Quotation must be enclosed in a properly sealed envelope addressed to the MNIT, Jaipur with kind attention to Assistant Registrar (S&P), MNIT, Jaipur by designation and not by name. The quotations must be super scribed Quotations for the supply of EQUIPMENT/Goods as called for in Tender Notice No dated DUE ON AT AM/PM. The Quotation must reach on or before AM/ PM on or before the due date and time mentioned in the tender notice/tender document. Details visit: 3. THE DOCUMENTS MUST BE DROPPED IN THE TENDER BOX AVAILABLE IN CENTRAL STORE DURING OFFICE HOURS (9.30AM to 6.00PM) ON ALL WORKING DAYS. BIDS DELIVERED TO ANY OTHER PLACE OR ANY INDIVIDUAL SHALL NOT BE CONSIDERED AS VALID DOCUMENT. QUOTATIONS SENT BY WILL NOT BE CONSIDERED VALID. 4. THE RATES QUOTED SHOULD BE F.O.R. JAIPUR inclusive of all charges e.g. packing, forwarding local taxes, railway freight, transit insurance, for outside firms and free delivery at Institute stores in the case of local firms. The rates may also be quoted separately "ex-godown/f.o.r. dispatching station. In case of Ex-Godown rates, please mention your packing and forwarding charges. Where there is no mention regarding delivery period in the quotations or where the items are offered ex-stock, the firms will be required to supply goods within one-month time. 5. Quotations should preferably be given only for those articles, which are available ex-stock. Other items should be quoted separately giving the delivery period. Rates of imported goods be quoted excluding custom duty as this institution is exempted from payment of custom duty. The rates of indigenous equipments may be quoted without Excise Duty as this institute is exempted from payment of Excise Duty. As far as possible, quotations should be given for goods of India manufacture and foreign goods, which are readily available. Foreign goods quoted and proposed to be supplied should be covered by normal import quota of the dealer. This institute is exempted from payment of custom duty.

2 6. Detailed specifications and "make" of each item should be clearly given supported by the illustrated pamphlets wherever possible. Quotations without specifying the make and other particulars may be rejected. The payment will be made after the goods have been received, opened, checked and found to be in order up to our entire satisfaction. The accessories included in the equipment should also be clearly mentioned. 7. Losses or damage in transit will be in to the account of the supplier in case of rates F.O.R. JAIPUR. The supplier may, if he so desires, get the goods insured and include such charges in the tendered rate. 8. The payment for the ordered items would be made after the articles have been received and found in order. Payment will be made by RTGS. Kindly send the RTGS details and cancelled cheque along with the Invoice. 9. Your rates should be valid at least for three months from the last date of receipt of quotations. 10. All legal proceedings, if necessity arises to institute may be any of the parties (Institute or Contractor/Supplier) shall have to be lodged in the courts situated at Jaipur and not elsewhere. 11. The undersigned is not bound to accept the lowest tender and may reject any tender or any part of the tender giving justification for such an action. 12. The rates must be quoted item-wise by giving Serial No. of our enquiry letter. 13. The quotations should preferably be sent duly typed. 14. (a) The Penalty Clause is as under :- Should the tenderer fail to deliver the goods within the period specified in the tender form the Institute may, at its discretion, allow an extension in time subject to recovery from the tenderer as agreed liquidated damages, and not by way of penalty, a sum equal to the percentage of the value of stores which the tenderer has failed to supply for period of delay as stated below: - (i) Delay up to one month 1% (ii) (iii) Delay exceeding one month but not exceeding two month Delay exceeding two month but not exceeding three month (iv) Delay exceeding three month 5% for each month and part there of subject to maximum 10% (b) In case of failure to supply the goods within the prescribed time and in accordance with the specifications give in the Quotations, the institute shall be free to cancel the order and make purchases from the next higher tenderer or from the open market as1 the case may be. In that case the loss sustained by the institute shall be recovered from the defaulting supplier. The institute will be at liberty to recover the loss from the permanent earnest money/or any other pending claims of the supplier without prejudice to its general right to affect recovery from the supplier. 15. EARNEST MONEY: A Demand Draft for 2 % of the quoted cost only in the name of the Registrar, M.N.I.T. may please be sent along with your tender as Earnest Money without which no tender shall be considered. Cheques are not accepted as earnest money amount. No interest is paid by us on the amount of earnest money 16. Successful Bidder has to Provide Performance 10% of the equipment cost, valid for 1 Year + 2 months for in the form of Bank's Guarantee from a nationalized bank. 17. Equipment specifications list are enclosed as annexure- I st 2% 5% ASSISTANT REGISTRAR Stores & Purchase

3 Annexure-I Real-time Embedded Systems Laboratory (RTESL) Sl No Name of the Equipment and Specifications Quantity 1 Universal microcontroller Development (UMD) Board which need to support the following integrated boards. - Education Practice Board: 8051, PIC, ARM7 and Arduino Integrated Board EEPROM with 4-10K memory or more. RTC DS 1307 with 32 Khz crystal with battery back-up. On Board Power Supply and also Through USB One 12V stepper motors with driver, which required 200 rpm, RPM based motor, 32KGCM torque or above of these specifications. All interrupts available on header LCD display. Graphical LCD display 8 I/Ps available from DIP switches. 8 O/Ps available on LEDs. 4 multiplexed 7-segment displays. 4-single bit keys, 8 Channel ADC with Potentiometers. On board DAC Section, On board Key pad section Provision of External inputs. On Board USB and RS232 Communications Reset on board programming Each UMD board must be provided with below mentioned daughter boards* (i) ARM with USB Interface MCU: 32 bit,128k Bytes Program Flash, 64K Bytes RAM, RTC, 2x UARTs operation standard JTAG connector with ARM 2x10 pin layout for programming/debugging with ARM-JTAG, On board status LED two on board voltage regulators 1.8V And 3.3V with up to 800mA current Power plug-in jack Single power supply: +5-9VDC required. Reset - On board programming. Provision of External inputs. 15 (ii) 8051 Daughter Board with USB Interface 8 bit MC with USB interface programming cable also work in standalone mode.

4 Reset - On board programming. Provision of External inputs (iii)arduino Daughter Board Microcontroller- ATmega328, Flash Memory- 32 KB SRAM-2 KB (ATmega328), EEPROM- 1 KB (ATmega328) Clock Speed- 16 MHz, Operating Voltage- 5V Digital I/O Pins- 2 box header (14 pins of which 6 provide PWM output, Analog Input Pins- On 1 box header (6 pins) Programming- USB Programming & SPI programming header Reset - On board programming. Provision of External inputs (iv) PIC microcontrollers 8 bit / 32 bit MC with USB interface programming cable also work in standalone mode. Reset - On board programming. Provision of External inputs *All the daughter boards must be compatible with universal board as specified in Sr GSM development Board ** 05 GSM development module with the quad band communication of frequencies (850,900,1800,1900 MHz) FME Antenna Connector Support Network Status LED Windows driver software for the GSM Application Based on 8051/pic/arm/avr microcontroller RJ11 Connector for handset Connection(optional) SIM Card Holder On Board 16x2 LCD display, 2relays, Buzzer, RTC & EEPROM, 8 LEDs, Stepper Motor Drivers, ADC Single Channel USB Based Reprogramming facility. ** GSM board must be compatible with UMD as specified in Sno.1 3 Zig bee Technology Trainer Kit: Zig Bee Coordinator & Gateway 05 Zig Bee Coordinator & Gateway The coordinators must be designed around advance processors and must act as gateway with other wireless connectivity etc. Zigbee 2.4 Ghz with external antenna. Coordinator based on ARM 7 LPC2148 Supporting various Network Topology with RF data rate 250 kbps or more. On board relays with isolated Output & one Buzzer for alarm activation On boards 20X4 LCD display for display for end device status

5 Facility to store the data SD Card for Storage Data entry using 4 4 Hex Keypad digital Input On Board USB Communication for PC Data transfer, Facility for switch selection for radio configuration, with / without processors On boards facility for GSM/GPRS & Bluetooth For data transfer: On Board Power supply (5V, 3.3V) with rechargeable battery backup, enclosure, With configurable device software, for GUI based, along with testing utility, RF data rate 250 Kbps with software selectable Data rate, with power supply 2.8V. The below mentioned add on devices also needs to be provided with Zig bee Technology Trainer Kit Zig Bee Intelligent End Devices 2nos The Zig Bee Intelligent End Device with USB interface, with ARM LPC 2148 Processor with SD card storage etc. Zigbee 2.4 Ghz/ 865 Mhz with external antenna Supporting various Network Topology with RF data rate 250 kbps/80 kbps On board 6V relays with isolated Output & one Buzzer On board 16X2 LCD display. 4 digital Input On Board Power supply (5V, 3.3V) Can Connect with any digital Sensor 0-5V or with analog sensors 4. SENSOR MODULES and Other Interfaces 05 Each module must include ALL the sensors / Interfaces as given below. - Humidity Sensor Onboard humidity sensor module with facility of conversion from relative humidity to voltage with range of operating humidity from 10-90% rh with accuracy of +-5% Operated voltage 5v test points to measure relative output voltage and power supply Facility to interface with microcontroller using on board header - Temperature sensor Facility to test different temperature sensors LM35, RTD, thermistor & thermocouple Sensors plug and play facility using input banana sockets Test points to measure output of each sensor Easy sensors input selection using on/off switches On board 8 channel ADC for analog to digital conversion Operational amplifier circuitry to boost signals Easy to use and interface with any processor,

6 -Magnetic sensor with two flat magnets. - Motion sensor PIR motion sensor, with o/p control of devices.it must be directly connected to microcontroller. - Proximity Sensors Used to detect the presence of nearby objects without any physical contact. - Smoke / Fire Sensors A smoke detector is a device that senses smoke, typically as an indicator of fire. Coverage of smoke and temperature detectors with European standard EN54 - Traffic Light sensor This interface simulates the control of Traffic Lights at a traffic island. In each of four directions (East, West, North, South). 5mm LED indicators Amber Red, yellow, green led are provided. 16 LED s are controlled through not gate. Finger Print Sensor Interfacing Kit Optical Finger print Reader Module with breakout board, for the easy integration with the microcontroller and PC. Power: 3.6V-6.0V, Interface UART TTL logical level Baud rate Character file size: 256 bytes Image acquiring time <0.5s, Template size: 512 bytes Storage capacity: 250, Security level highest, Average searching time < 0.8s. RFID Reader with Tags On board RFID card reader USB port interface to computer. Card detection range from 3-10cm. ASCII format output through a simple USB USART interface Compatible with multi processor with jumper selection On Board connectors LED indicators, On boards Buzzer interface Special On board USB port for PC/ laptop Interface BlueTooth Module Bluetooth protocol: Bluetooth Specification v2.0+edr

7 Compatible with multi processor with jumper selection On board USB port for PC/ laptop Interface. Frequency: 2.4GHz ISM band Modulation: GFSK(Gaussian Frequency Shift Keying) 1Mbps/1Mbps Security: Authentication and encryption Power supply: +3.3VDC 50mA On Board connector for processor interface WIFI-modules interface Single stream 2.4 GHz with support for WEP secuity mode as well as WPA/WPA2. Compatible with multi processor with jumper selection On board USB port for PC laptop Interface. Includes all the protocol and configuration functions for Wi-Fi connectivity. Support Smart Link Function Support Dial Switch to Control Power Support Max 3 Channel PWM Output FCC Certified. RoHS and CE compliant. Single supply 3.3V operation Support WPS function. 5 BLUETOOTH TRAINER KIT The mentioned trainer kit must be Computers independent Training System 02 Graphical LCD display Blue tooth enabled devices detection Based On AVR(Atmega 128) Designed considering all the Communication Standards Data Generators is provided on -board User friendly software Test points are provided to observe signals Carrier Frequency 2.40 Ghz to 2.48GHz Bandwidth 80 MHz,Modulation GPSK, 1Mbps No of Channels 79,Channel Interviews 1MHz Frequency Hopping 1600 hops/sec Transmission Range 10 meters approx Output Interface UART & USB I/O connector in form Of 10 Pin Header Box. Power Supply 230V ±10%, 50Hz Operating Voltage 5V OS Support: XP/Vista/Windows7 Antenna Whip Antenna

8 6 SMART PHONE TRAINER KIT The system must be able to explore MOBILE applications. Video Tutorial and soft manual. 02 Step by step training through graphical LCD. Facility for learning AT command SET thru LCD Display. 4x4 multiplexed keypad. Alpha numeric keypad for AT Command set. Fixed / variable SMS to any number thru keypad. RS- 232 Serial interface. GSM Frequency 850MHz. Based on Processor Core: Ardunio or raspberry Pi On Board Wifi, Bluetooth, GSM module. 7 Object Detection and tracking using Tracked Robo Kit using Raspberry Pi / AVR / ARM/ Arduino Robot should have Metallic body. AVR (Atmega328 ) / Raspberry Pi / Arduino / ARM based Servo Controller, SERVO MOTOR which includes Standard Size Servo. Serial port-based version with powerful PC software. Software controlled Feature and reprogrammable using GUI. Reprogramming Facility available Using USB IR based object detection and tracking desired object. Camera based color detection on conveyor belt mechanism.image processing application through matlab Android based control of robotic motion Open platform for Android Application through Bluetooth. Force sensor /IR sensor On Board DC motor Interface For conveyor based application 01 Assistant Registrar Store & Purchase