WAVELET WATER QUALITY MONITORING KIT

Transcription

1 AYYEKA Rethink Water Monitoring WAVELET WATER QUALITY MONITORING KIT ON OFF QUICK START GUIDE AYYEKA

2 IMPORTANT! Use with pressure applications up to 145 PSI. Contact AYYEKA SUPPORT center for technical support at +1 (310) ALWAYS COORDINATE Wavelet Water Quality Monitoring Kit installation with the local water company before starting installation works, which should be completed by trained and authorized personnel. The WARRANTY offered by Ayyeka covers only Ayyeka supplied hardware and software for the duration of the warranty period as per the warranty terms and conditions.! AYYEKA IS NOT LIABLE for damage or injury as a result of handling, installation or maintenance of its supplied systems. 2G cellular network signal. DO NOT THROW AWAY away the Wavelet Water Quality Monitoring Kit, as it contains a lithium battery. Please dispose of properly. 1

3 SITE REQUIREMENTS & PREPARATION 1. Required site conditions: Minimum pipe diameter of 4 inches. Chlorinated drinking water in steel pipes psi is the operational pressure range. Maximum peak pressure is 435 psi. Water temperature range of F. Minimum water velocity of 0.1 ft/sec. 2G cellular network signal. Sensor must be wet before being connected to the Wavelet. If the sensor is installed in intermittent water flow (turning on/off), its lifetime will be drastically decreased. 2

4 2. Prepare the site: SITE PREPARATION Prepare 2 NPT ball valve that is fixed perpendicular to the pipe surface and 45 to the ground. The maximum height from the interior of the pipe to the top of the ball valve is 6 inches. Ball Valve Max. 6 Height To avoid turbulence and air bubbles, install ball valve as close to the middle of the pipe span and as far from pipe bends or equipment as possible. pump After fixing the ball valve to the pipe, ensure that the internal diameter of the hole punched for installation of the sensor is at least 1.7 inches. 1.7 diameter for insertion of water quality sensor 2 ball valve 4 diameter pipe 3

5 GETTING STARTED! Pipe Wrench 1x Bucket 1x Thread Seal Tape 1x Wavelet Water Quality Monitoring Kit 1 Sensor Cable 2 Water Quality Sensor 1x 1x 3 Wavelet Device 4 Gasket 1x 1x 5 Pipe Fitting 6 Zip Ties, Screws, and Anchors 1x 4 2x 4x 4x

6 NOTE: Special Installation Locations Weak Cellular Service Locations: If the Wavelet is installed in an area with weak cellular reception, activate the Wavelet and place in the intended intallation location with closed doors/access hatch. Log into home.ayyeka.com to ensure that GSM signal has been recently updated in the last few minutes. Underground/Indoor Wavelet Installations: Before installation, activate the GPS outside by turning on the Wavelet (see step 10). Wait for at least 8 minutes, then log in to the user interface at home.ayyeka.com to confirm updated location on the map. 5

7 WATER QUALITY SENSOR PREPARATION 1 Place tip of sensor in water for 30 minutes prior to installation.! CAUTION: Sensor should never be connected to the Wavelet device while dry. Do not yet connect the sensor to the Wavelet device. Only connect once the sensor is wet and installed in the pipe. 6

8 2 Choose proper installation configuration and location, taking into account cable length. Pipe Mounted Wall Mounted AYYEKA AYYEKA Do Not Install Upside Down AYYEKA 7

9 ON OFF 3 Wrap thread seal tape onto the pipe fitting, and screw it tightly into the valve with the pipe wrench. 4 Put the gasket onto the neck of the sensor. 8

10 ON OFF 5 While the valve is closed, thread the sensor into the pipe fitting up to ¼ BELOW the white stripe marking on the sensor.! CAUTION: Be careful not to apply too much force with the wrench. Going beyond the bottom of the white line will irreversibly BREAK the sensor. 1/4 clearance below white stripe 9

11 6 Open valve completely. Water will spray, which can be mitigated by holding a towel around the base of the sensor connection to the pipe fitting. ON OFF 7 Thread the sensor all the way until the gasket is sealed to prevent water leakage. ON OFF 10

12 WAVELET ACTIVATION 8 Connect cable to the Wavelet. Screw until tightly fastened. 9 Remove cap from top of sensor. Connect opposite end of cable to the sensor. B A ON OFF 11

13 10 Remove screws to open the back panel of the Wavelet device. Activate the Wavelet by sliding the switch to the ON position. Wavelet will then initiate a 20 minute online test mode. OFF ON 11 Access the Ayyeka user interface at home.ayyeka.com using your log-in credentials. Expect data to appear between minutes after the online test mode is complete. 12

14 Water Quality Kit Water Quality Kit ppm ppm psi psi minutes ago minutes ago 3 ago minutes ago 85.8 F minutes ago minutes ago Water Quality Kit Water Quality Kit psi 85.8 F ppm ppm 24 hours ago 24 hours 24 ago hours ago 24 hours ago 24 ago The screen display should resemble the following: Water Quality Kit Water Quality Kit Water Quality Kit Water Quality Kit ppm ago ppm ppm minutes ago ppm 24 hours ago minutes ago 24 hours 24 ago hours ago 3 24 hours ago ago 24 ago psi ago psi Fpsi ago 85.8 F 24 If Wavelet is transmitting properly, you have completed the installation successfully and can begin collecting and viewing your data! If data does not transmit properly, change the Wavelet installation location and activate again. If the problem persists, contact support@ayyeka.com or +1 (310) for assistance. 13

15 13 Screw the back panel of the Wavelet back on to the device according to the numbering scheme. Then, secure the Wavelet to its location. 4x 4x Wall Mounted 2x Pipe Mounted Your Wavelet Water Quality Kit is now successfully installed! 14

16 AYYEKA QUESTIONS? +1 (310)