HOSTED VOICE Bring Your Own Bandwidth & Remote Worker Install and Best Practices Guide
2 Thank you for choosing EarthLink! EarthLinks' best in class Hosted Voice phone service allows you to deploy phones anywhere with a Broadband connection. This flexibility allows you to take your EarthLink service home or when you travel. This guide will review the requirements for the local nework, internet service provider and bandwidth when using EarthLink Hosted Voice with a 3rd party Connection. Although unique deployment steps may vary from one network to another, most issues encountered during Hosted Voice deployments can be addressed by following a few key steps. Networks must be designed to support VoIP and the actual deployment can present a wide range of challenges. This guide is a tutorial to show you how to install your EarthLink phone and provide best practice recommendations for a successful implementation. IMPORTANT: The FCC requires that providers of IP-based phones services remind you of important 911 Service information. EarthLink requires an updated and accurate service address to insure that emergency 911 services can be dispatched to your actual location. If you move your equipment location, contact EarthLink Customer Care at 800-239-3000 in advance to provide your new address. 911 callers need to know the address and telephone number of their location when contacting emergency services. If your electricity or internet services are down due to an outage or other technical issue, 911 emergency services may not function.
3 Installation Guide Step 1 Assemble your New Phone Remove your new phones from their boxes and follow the included instructions to assemble the phones and then place them at the final install location. The boxes will be labeled with the phone number to help you identify their placement. Step 2 Connect Hosted Voice Phones Every network layout is unique with unique design considerations however most networks fall into one of the following categories: INSTALL PHONE USING YOUR MODEM Your broadband modem will connect to your Service Provider A cable will connect from yourmodem/router to your IP phones LAN port A cable will connect yourcomputer to the IP phone Broadband Modem/Router IP Phone Computer on the PC port INSTALL PHONE USING YOUR ROUTER OR WiFi ACCESS POINT Laptop Your modem will connect to your Service Provider A cable will connect the modem to your router IP Phone A cable will connect your router to the IP phones Modem Customer Router LAN port A cable will connect your computer to the IP phone Computer on the PC port INSTALL PHONE USING A FIREWALL Your modem will connect to your Service Provider A cable will connect the modem to your firewall A cable will connect your firewall to the IP phones LAN port Broadband Modem/Router Firewall IP Phone Computer A cable will connect your computer to the IP phone on the PC port
4 Step 3 Configure Network Devices Configuration changes may be needed on one or more devices on your network depending on the network layout. INSTALLATION USING YOUR MODEM Connecting your phone directly to the modem/router provided by your Service Provider (ISP) usually requires the least configuration changes. Disable SIP Aware features on the modem Different vendors refer to SIP aware functionality by different names but it is often referred to as SIP Application Layer Gateway (ALG), Stateful Packet Inspection (SPI) or SIP NAT. These settings are commonly found in the firewall, security, advanced or WAN configuration page, but may also be elsewhere on the settings. Disable firewall features on your modem INSTALLATION USING YOUR ROUTER OR WIFI ACCESS POINT The need for an additional router or WiFi Access Point may prevent you from plugging the phone directy to your modem. Set your modem to Bridge Mode This allows your internet conenction be handled by your router; in essence you are buiding a bridge so that traffic travels through your modem directly to your router. Disable SIP Aware features on your router Disable firewall features on your router INSTALLATION USING A FIREWALL Firewalls are advanced applications meant to protect your network by inspecting all data and allowing valid traffic while rejecting anything unauthorized. While some firewalls are software within your router, others can be an external device on your network. When using a firewall, rules need to be configured to ensure the EarthLink voice and phone provisioning traffic is allowed access. Set your modem to Bridge Mode This allows your internet conenction be handled by your router; in essence you are buiding a bridge so that traffic travels through your modem directly to your firewall. Disable SIP Aware features on your firewall Add IP addresses required for EarthLink voice services to the allowed/whitelist on the firewall Due to the variety of Service Providers and network hardware manufactures it is not possible to detail the exact steps needed to make the required network changes. For assistance in completing the configuration changes please contact your ISP or hardware manufacture.
5 Implemention Best Practices Network Design Recommendations Double-NAT Whenever possible the IP phone should connect directly to the modem/router provided by your internet service provider. Many larger networks require the addition of routers, switches, firewalls. When there is more than one router between the phone and the internet, it will create a double NAT topology causing phones to not register, receive one-way audio or no audio at all. Double-NATing is known to cause many problems for VoIP phones and is not a supported topology. If utilizing a router the modem should be in bridged mode. Below are some examples of common topologies where double NAT exists: Double NAT Wireless Router with NAT Double NAT Firewall Modem with NAT Modem with NAT EarthLink recommends only one device t performing NAT between the phone and the internet. VLANs Using VLANs allows you to segment the IP phones on your network onto separate virtual networks. VLANs allow you to create separate rules and configurations that only apply to the IP phones and are highly recommended. The IP Phones utilize the industry standard Layer Link Discovery Protocol (LLDP) to identify themselves as IP phones. When used in combination with a LLDP-Supported switch, VLANS allow for easy implementation of Hosted Voice. EarthLink recommends utilizing a LLDP capable switch and segmenting phones onto a separate VLAN. DHCP When EarthLink Hosted Voice phones boot they need to acquire their configurations. Initial configurations are retrieved via TFTP from 66.0.4.130. To assist in easy installation, the phones can acquire boot server information from the network DHCP server. EarthLink recommends that your DHCP server is configured with DHCP Option 66 to 66.0.4.130.
6 Firwall and Security Recommendations Firewalls are intended to protect your network from unauthorized traffic and to ensure the security of your data. Generally speaking you do not want voice traffic passing through your firewall but if needed, the following should be implemented: Disable any SIP (Session Initiation Protocol) aware functionality SIP ALG (Application Layer Gateway), SIP NAT, SPI(Stateful Packet Inspection), SIP Fixup There should be no manipulation or translation of the SIP Messaging Configure rules to allow traffic to the EarthLink Voice Network See the table below for a list of IPs the phones need to receive and send traffic IP ADDRESS PROTOCOL PORT UDP/TCP 209.165.1.56 SIP/RTP All UDP 209.165.1.57 SIP/RTP All UDP 209.165.1.58 SIP/RTP All UDP 209.165.1.59 SIP/RTP All UDP 209.165.2.22 SIP/RTP All UDP 209.165.2.23 SIP/RTP All UDP 209.165.2.28 SIP/RTP All UDP 209.165.3.20 SIP/RTP All UDP 209.165.3.51 SIP/RTP All UDP 209.165.3.53 SIP/RTP All UDP 66.0.4.130 TFTP 69 UDP 207.190.193.55 HTTP 80 TCP 207.190.193.55 HTTPS 443 TCP 97.67.232.176 HTTP 80 TCP 97.67.232.176 HTTPS 443 TCP 97.67.232.172 HTTP 80 TCP 97.67.232.172 HTTPS 443 TCP
7 Quality of Service (QoS) Recommendations When making a Voice over IP (VoIP) call, the sound of your voice is converted to digital information and broken into thousands of pieces known as packets. These packets travel through the to the EarthLink voice network. Latency (the time it takes a voice packet to reach its destination), jitter (variation of latency within the network) and packet loss (dropped/disgarded packets) are the most common issues to impact voice quality. Network congestion can delay or drop packets and even a few dropped packets on a voice data stream can introduce echo, breaks in voice conversation or dropped calls. While it is not possible to guarantee reliable delivery of packets that are sent over the public internet, ensuring the voice traffic has the highest priority and sufficient bandwidth will provide the highest possible quality voice communications. DSCP Tagging To ensure the best possible voice quality, EarthLink will mark all VoIP traffic so it can be prioritized on your network. EarthLink s Hosted Voice phones are configured to use DSCP (Differentiated Services Code Point) 46 for all VoIP traffic. Bandwidth Like browsing the internet or streaming music, each phone call you make is utilizing your internet bandwidth. It is important that there is sufficient bandwidth to ensure high quality calls. Each phone call utilizes approximately 100 kbps of bandwidth including calls between two phones at the same site. EarthLink recommends for the customer s equipment to match and prioritize all traffic marked with DSCP 46. When spikes in network traffic occur, the router/modem should throttle the traffic to allow sufficient bandwidth for the voice. Note that while using non-earthlink provided internet/network access, EarthLink cannot guarantee call quality and QoS outside of EarthLink s own network infrastructure. IMPORTANT: The FCC requires that providers of IP-based phones services remind you of important 911 Service information. EarthLink requires an updated and accurate service address to insure that emergency 911 services can be dispatched to your actual location. If you move your equipment location, contact EarthLink Customer Care at 800-239-3000 in advance to provide your new address. 911 callers need to know the address and telephone number of their location when contacting emergency services. If your electricity or internet services are down due to an outage or other technical issue, 911 emergency services may not function.