. Support Around The Board Device Specification. EMERSON NITX-300 Series Ultra Low Power Nano-ITX Motherboards www.avnet-embedded.eu
NITX-300 Series Ultra Low Power Nano-ITX Motherboards PRELIMINARY DATA SHEET Easy-to-use Nano-ITX motherboards are ideal for low power embedded applications n < 7 Watts typical power consumption n Up to 1.0 GHz Intel Atom processor E6xx series n Up to 1GB DDR2 memory, soldered on board n Gigabit Ethernet, SATA and USB n PCI Express x1 and PCI Express Mini Card slot ndual display support nfour serial ports The NITX-300 series of Nano-ITX motherboards from Emerson Network Power feature the Intel Atom processor E6xx series. These ultra low power motherboard solutions offer passive cooling capability for reliable operation. They are designed for use in a variety of applications such as embedded instruments, medical carts, audio visual display systems, and other applications that require an easy-to-use Nano-ITX motherboard with support for a variety of operating systems. With a size format of 120 mm x 120 mm, Nano-ITX form factor motherboards are very suitable for low power embedded applications. The NITX-300 series has a low height profile to fit into most enclosures and has a wide range of built-in connectivity including LCD and/or CRT displays; SATA for physical or solid state disks; a PCI Express x1 expansion slot and a PCI Express Mini Card slot for Wi-Fi/WiMAX; USB and Gigabit Ethernet networks; audio; and multiple serial ports.
NITX-300 Series Block Diagram Audio 1 Channel DDR2-667/800 non-ecc DDR2 667/800 32-bit Up to 1GB Memory Down Mic Phone SDVO LVDS Audio VGA Line/Phone Line/Mic VGA ALC888 CODEC Chrontel CH7317 HD Audio SDVO HD Audio Intel Atom Processor E640 or E620 PCIe x1 LPC LVDS Backlight Ctrl TPM/Debug Internal LVDS Conn SPI (2x CS#) SMbus PCA 9577 8x GPIO LPC SMbus SPI EFI FW 4x PCIe x1 PCIe x1 PCIe x1 USB PCIe MiniCard 6x USB 2.0 Host (2 controllers) USB 1x USB Device Port 1x 1GbE MAC SATA SATA Ethernet 1GbE Marvel 88E1111 1GbE RGMII Intel Platform Controller Hub EG20T SATA 1x CAN SDIO Slim Lite SSD CAN MicroSD Socket 1x CAN Bus 4x UART 2x SATA SDIO Pwr/Rst/LED SDIO Pwr/Rst/LED 2x SDIO SPI (2 CS#) 4x UART 4x RS-232 I2C SMbus Temp, Voltage, Fan USB Client 2
Hardware Specifications PROCESSOR 1.0 or 0.6 GHz Intel Atom processor E640 or E620 CHIPSET Intel Platform Controller Hub EG20T MEMORY 512MB or 1GB soldered down DDR2 VIDEO Supports dual display outputs with a single channel LVDS and VGA connectivity. LVDS resolution up to 1280 x 768, VGA resolution up to 1280 x 1024 pixels at 60 Hz STANDARD REAR I/O One (1) Gigabit Ethernet Two (2) USB 2.0 One (1) VGA Two (2) audio jacks One (1) 12V power input socket INTERNAL I/O EXPANSION One (1) PCI Express x1 slot One (1) PCI Express Mini Card slot for WiFi/WiMAX wireless module Four (4) USB headers One (1) USB Client header One (1) GPIO header Four (4) Serial headers One (1) LVDS header One (1) CAN header One (1) Audio header One (1) SATA connector One (1) Bottom-mounted Slim-Lite SSD connector One (1) Bottom-mounted MicroSD memory card connector One (1) LPC header POWER CONSUMPTION Typical use < 7 Watts COMPLIANCE AND CERTIFICATION INFORMATION EMC and Safety Class B (FCC, VCCI, MIC, AS/NZ) UL, CSA, Ctick Firmware and Operating System Support BIOS UEFI BIOS OS COMPATIBILITY: Microsoft Windows XP Windows Windows 7 Microsoft Windows Embedded Standard Meego Linux Wind River Hypervisor 1.2 Wind River VxWorks 6.8.2 Wind River Linux 4 Wind River Tilcon Graphics Suite 5.8 NITX-315-DEVKIT Contents Nano-ITX Motherboard Power supply Drivers CD Cable Pack (SATA power and data, USB) Wind River On-Board Embedded Development Kit including: One (1) Getting Started with Wind River guide One (1) 16GB LiveUSB stick containing Workbench 3.2.3, Hypervisor 1.2, WR Linux 4.0, VxWorks 6.8.2 and Tilcon 5.8.1 One (1) 4GB microsd pre-loaded with Wind River Hypervisor 1.2 running VxWorks 6.8.2 and Wind River Linux 4 as Guest OS The Wind River On-Board Embedded Development Kit for the NITX-300 Seed Board is ideally suited for developers that wish to develop graphics applications, as well as for those developers that wish to run multiple applications using the on-board hypervisor technology. The 30-day evaluation software includes Wind River Hypervisor with VxWorks and Wind River Linux as Guest OS. Wind River Linux is pre-inte grated with the Intel Embedded Media and Graphics Driver. The LiveUSB stick that aompanies the kit is pre-installed with both the Wind River Workbench IDE for embedded development and the Tilcon GUI tools for graphics development. By working closely together, Emerson and Wind River are making development aess easier, faster and more affordable than ever by putting all the tools in one box for customer evaluation. 3
Ordering Information Part Number NITX-315-DEVKIT Description NITX-315 with Wind River and Meego bootable USB sticks and power adaptor NITX-315-ET 1.0 GHz Extended temperature Intel Atom Processor E640T, 1GB memory, -20 C to +70 C NITX-315 NITX-300 1.0 GHz Intel Atom processor E640, 1GB memory 0.6 GHz Intel Atom processor E620, 512MB memory SOLUTION SERVICES Emerson Network Power provides a portfolio of solution services optimized to meet your needs throughout the product lifecycle. Design services help speed time-to-market. Deployment services include global 24x7 technical support. Renewal services enable product longevity and technology refresh. Intel and Atom are trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Microsoft and Windows are trademarks of Microsoft Corporation. All other product or service names are the property of their respective owners. This document identifies products, their specifications, and their characteristics, which may be suitable for certain applications. It does not constitute an offer to sell or a commitment of present or future availability, and should not be relied upon to state the terms and conditions, including warranties and disclaimers thereof, on which Emerson Network Power may sell products. A prospective buyer should exercise its own independent judgment to confirm the suitability of the products for particular applications. Emerson Network Power reserves the right to make changes, without notice, to any products or information herein which will, in its sole discretion, improve reliability, function, or design. Emerson Network Power does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent or other intellectual property rights or under others. This disclaimer extends to any prospective buyer, and it includes Emerson Network Power s licensee, licensee s transferees, and licensee s customers and users. Availability of some of the products and services described herein may be restricted in some locations. Emerson Network Power. The global leader in enabling Business-Critical Continuity. AC Power Connectivity DC Power Embedded Computing Embedded Power Infrastructure Management & Monitoring Outside Plant Power Switching & Controls Precision Cooling Racks & Integrated Cabinets Services Surge Protection Emerson Network Power Offices: Tempe, AZ U.S.A. 1 800 759 1107 or +1 602 438 5720 Paris, France +33 1 60 92 31 20 Munich, Germany +49 89 9608 2333 Tel Aviv, Israel +972 9 9560361 Hong Kong +852 2176 3540 Shanghai, China +86 21 3395 0289 Tokyo, Japan +81 3 5403 2730 Seoul, Korea +82 2 3483 1500 EmersonNetworkPower.com/EmbeddedComputing Emerson, Business-Critical Continuity and Emerson Network Power are trademarks of Emerson Electric Co. or one of its affiliated companies. 2011 Emerson Electric Co. NITX300-D2 01/11
www.avnet-embedded.eu OFFICES. Denmark Avnet Nortec A/S Ellekær 9 2730 Herlev Phone: +45 3678 6250 Fax: +45 3678 6255 denmark@avnet-embedded.eu Finland Avnet Nortec Oy Tiilenpolttajankuja 3 A B 1720 Vantaa Phone: +358 20 749 9260 Fax: +358 9 4259 7446 finland@avnet-embedded.eu FrancE Avnet EMG France SA Immeuble 154, Parc Chene 2 5, allée du General Benoist 69500 Bron Phone: +33 4 72 81 02 30 Fax: +33 4 72 81 02 34 bron@avnet-embedded.eu Avnet EMG France SA 14 avenue Carnot F-91349 MASSY Cedex Tel: +33 (0)1 64 47 29 29 Fax: +33 (0)1 64 47 99 99 paris@avnet-embedded.eu Avnet EMG France SA Les Peupliers II 35 avenue des Peupliers 35510 Cesson-Sévigné Phone: + 33 2 99 77 37 02 Fax: + 33 2 99 77 37 01 rennes@avnet-embedded.eu GERMANY (AUSTRIA, CZECH REPUBLIC, HUNGARY, POLAND, SWITZERLAND) Avnet EMG GmbH Gruber Straße 60c 85586 Poing Phone: +49 8121 775 500 Fax: +49 8121 775 550 poing@avnet-embedded.eu Avnet EMG GmbH Lötscher Weg 66 41334 Nettetal Phone: +49 8121 775 500 Fax: +49 8121 775 550 nettetal@avnet-embedded.eu ITALY (PORTUGAL, SPAIN) Avnet EMG Italy SRL Via Manzoni, 44 20095 Cusano Milanino Phone: +39 02 660 92 1 Fax: +39 02 660 92 498 milano@avnet-embedded.eu NETHERLANDS (BELGIUM, LUXEMBOURG) Avnet B.V. Takkebijsters 2 4817 BL Breda Phone: +31 76 5722400 Fax: +31 76 5722404 benelux@avnet-embedded.eu SWEDEN (NORWAY) Avnet Nortec AB Esplanaden 3 D 172 67 Sundbyberg Phone: +46 8 564 725 50 Fax: +46 8 760 01 10 sweden@avnet-embedded.eu UNITED KINGDOM (IRELAND) Avnet EMG Ltd. Pilgrims Court, 15/17 West Street Reigate, Surrey, RH2 9BL Phone: +44 1737 227800 Fax: +44 1737 244698 uk@avnet-embedded.eu All trademarks and logos are the property of their respective owners. This document provides a brief overview only and is not intended to be complete or binding offer. Product information, including information related to a product s specifications, uses or conformance with legal or other requirements, is obtained by Avnet from its suppliers or other sources deemed reliable and is provided by Avnet on an As Is basis. Avnet makes no representation as to the auracy or completeness of the product information and Avnet disclaims all representations, warranties and liabilities under any theory with respect to the product information, including any implied warranties of merchantability, fitness for a particular purpose, title and/or non-refringement. All product information is subject to change without notice. 04/2011