178 HI-LINE UTILITY SUPPLY CO. CHAIN - COFFING Roller Chain Type These hoist are popular with lineman because they offer a longer reach when "bicycle" chain is held sideways. Rugged, durable design and construction assures sure operation and freedom from maintenance. Hoist is free chaining when not under load. Single, double, and multi chain models are offered. Double chain models offer extended reach at half the load when used in the single chain mode. NOT DESIGNED FOR SIDE LOADS! MODEL ATG *DOUBLE-LOCKING PAWL models allow load to be raised or lowered with only a half stroke of the handle. These models are designated with an I suffix. Rated Hndl No. of Std Wgt Cat. No. Load Lgth Chains Lift lbs. AG / *AGI 1,500 lbs 18.75 1 56.5 14 ATG / *ATGI 1,500 lbs 18.75 1 57 17 3,000 lbs 2 110 FG / *FGI 3,000 lbs 27.5 1 56.5 25 FTG / *FTGI 3,000 lbs 27.5 1 57 34 6,000 lbs 2 110 ZG-4 9,000 lbs 33.5 3 53 49 ZG-6 12,000 lbs 33.5 4 53 59 PARTS ON PAGE 280-281 PULLING EYE Cat. No. PE-1 This tool provides a large offset eye to accommodate hoist hooks and leaves the anchor eye free for attaching guy grips or strand vises. The included PE-1-B adapter bushing quickly adjusts to fit 1/2" - 1-1/4" rods. Safe work load is 6,000 lbs. REMOVE WEDGE FOR USE ON 1-1/4 RODS CHAIN HOIST - RATCLIFF Roller Chain Type These hoist offer compact steel construction and a "fast lift" design which allows the operator to choose its one or two notch take up capability per lever stroke. Loads are carried and held by alloy steel pawls against steel gears. The housing is of cast alloy steel and all bushings are lifetime lubricated. NOT DESIGNED FOR SIDE LOADS! Cat. Rated Hndl No. of Std Wgt No. Load Lgth Chains Lift lbs. NBR-1 1,500 lbs 18 1 55 17 NCR-1 2,000 lbs 20 1 55 17 NDR-1 2,500 lbs 24 1 55 19 NBR-2 3,000 lbs 18 2 54 25 NCR-2 4,000 lbs 20 2 54 25 NDR-2 5,000 lbs 24 2 54 26 NDR-3 7,500 lbs 24 3 53 41 NDR-4 10,000 lbs 24 4 53 49 PULLING HOOKS Commonly referred to as "tuning fork" or "crows foot", this hook holds a conductor or guy deadened in line with the cable for ease during installation. MODEL NBR-2 Cat. Work Eye Width No. Load x Length 9055 5,200 lbs 1.5" x 10" 9062 4,000 lbs 4" x 15" WPH3 3,500 lbs ----
HI-LINE UTILITY SUPPLY CO. 179 CHAIN - RATCLIFF These hoist offer compact steel construction and a "fast lift" design which allows the operator to choose it's one or two notch take up capability per lever stroke. Loads are carried and held by alloy steel pawls against steel gears. The housing is of cast alloy steel and all bushings are lifetime lubricated. CHAIN - COFFING These hoists incorporate a dual ratchet and pawl design which provides easy operation and freedom from maintenance. The body and handle are built of high-strength aluminum alloy for light weight and corrosion resistance. An open body construction permits easy inspection of suspension hook assembly. Cat. Rated Hndl No. of Std Wgt No. Load Lgth Chains Lift lbs. NBC-1 1,500 lbs. 18" 1 55" 14 NDC-1 3,000 lbs. 24" 1 55" 16 NDC-2 6,000 lbs. 24" 2 54" 23 NDC-3 9,000 lbs. 24" 3 53" 37 NDC-4 12,000 lbs. 24" 4 53" 46 CHAIN HOIST - CM RIGGER This compact hoist is simple, light weight, and economically priced. Cat. Rated Hndl No. of Std Wgt No. Load Lgth Chains Lift lbs. 2301 1,500 lbs. 1 7.5 2302 3,000 lbs. 15" 2 60" 12.5 CHAIN HOIST Catalog Number LMSC-1500 This compact hoist is simple, light weight, and economically priced. 1,500 LB CAPACITY 5' LIFT WEIGHT - 19 LBS. Cat. Rated Hndl No. of Std Wgt No. Load Lgth Chains Lift lbs. RA-15 1,500 lbs. 1 12 RA-20 2,000 lbs. 1 12 RA-15-2 3,000 lbs. 2 18 RA-30 3,000 lbs. 20.5" 1 60" 23 RA-30-2 6,000 lbs. 2 35 RA-30-3 9,000 lbs. 3 53 RA-30-4 12,000 lbs. 4 63 DISC BREAK MODELS ALSO AVAILABLE 1 TON CHAIN HOIST - CHANCE Cat. No. 3011S The handle and sheave housings on this hoist are made of lightweight high-strength heat-treated aluminum. All working parts are fully enclosed in the housing unit to protect the hoist mechanism and to cover the gearing for worker safety. The handle swings to either side allowing operator to reach overhead or below chest level to operate hoist. Chain is high-strength alloy steel. Load hooks are forged steel with gate type latches. Both top and bottom hooks swivel 360o to allow for unwinding action of rope or stranded cable under tension. Lift; 5-1/2', Weight; 14 lbs.
180 HI-LINE UTILITY SUPPLY CO. STRAP These Cable & Conductor Pullers have been re-engineered! They continue to be specifically designed for smooth, easy, and reliable operation during line construction work. Nylon straps and fiberglass handles provide some dielectric properties, when clean and dry. These hoists are not insulated live-line tools. These hoists should be used with appropriate length, properly applied insulating link sticks when working on energized electrical lines. See next page. Most of the hoists listed in this section are "convertible" models. They can be used in a "single" or "double" strap mode. The single strap mode allows for a longer reach at half the capacity. All have fiberglass handles, web straps, and are available with different combinations of standard hooks, hot stick rings, and gate hooks. Please call with questions not covered in the tables below. For use on straight pulls only. 31A Std LUG-ALL Cat. No. Hot Rings Gate Rated Capacities - Pounds Single Strap Double Strap 1,500 2,000 Lift 3,000 4,000 Lift Hndl Length 31A 31B 31U X 11 X 5 20 11 4 4B 4U X 9 X 4 36" 15 Wgt Lbs. SEE REAR OF CATALOG FOR REPAIR PARTS LITTLE MULE Cat. No. Std Hot Rings 300A 300DA 300CB ---- 300DHB Gate Rated Capacities - Pounds Single Strap Double Strap 1,500 2,000 Lift 3,000 4,000 6,000 Lift X 9' X Handle Length 4.25' 24-3/4" 344B 344DB 344CB X 11' X 5-1/2' 32" 15 ---- 344DHB 6000A 6000DA 6000CA --- --- --- X 5' 20" 26 Wgt Lbs. 14 344B If you can t find it... call HI-LINE!
HI-LINE UTILITY SUPPLY CO. 181 CHANCE Cat. No. Std Hot Rings Gate Rated Capacities - Pounds Single Strap Double Strap 1,500 2,000 Lift 3,000 4,000 Lift Hndl Length PSC309-0451 PSC309-0452 X 7' X 4' 30" 13 --- PSC309-0467 X 6' --- --- --- 30" 14 PSC309-0468 4,000 4' --- --- --- 36" 16 Wgt Lbs. PSC309-0468 DYNAMOMETERS see page 208 CHANCE HOIST LINK STICKS A properly applied link stick insulates a nylon-strap ratchet hoist from an energized conductor during hot line work. It is a 1-1/4" diameter fiberglass pole with a steel safety hook on one end and a butt swivel on the other. Rated working load is 4000 lbs. C403-1175 Cat. No. Length Between End Fittings Wgt C400-1175 15" Isolated Link w/ HS Ring 4 lbs C400-2399 18" Isolated Link w/ HS Ring 5 lbs C400-2400 24" Isolated Link w/ HS Ring 6 lbs HASTINGS HOIST LINK STICKS A properly applied link stick insulates a nylon-strap ratchet hoist from an energized conductor during hot line work. It is a 1"diameter fiberglass pole with a steel safety hook on one end and a butt swivel on the other. Rated working load is 4000 lbs. 3410A Cat. No. Length Between End Fittings Wgt 3413 6 Isolated Link - No HS Ring 2.25 lbs 3413-1 6 Isolated Link w/ HS Ring 2.25 lbs 3414 12 Isolated Link - No HS Ring 2.25 lbs 3414-1 12 Isolated Link w/ HS Ring 2.25 lbs 3409 6 Isolating Link w/ Clevis Roller 2.25 lbs 3410A 12 Isolating Link w/ Clevis Roller 2.5 lbs 3409-1 6 Isolating Link w/ CR & HS Ring 2.25 lbs 3410A-1 12 Isolating Link w/cr & HS Ring 2.5 lbs
182 HI-LINE UTILITY SUPPLY CO. CAPSTAN - 1,000 LB. AND 3,000 LB. LOAD RATING 12V, 115V, 230V, Hydraulic, and Gasoline Powered Powerful new design for tough jobs! Improved design features a multiple-planetary drive/back- stop clutch assembled on the center shaft to a steel gear case with fulllength internal teeth. This design handles more rugged jobs, extends service life and reduces maintenance. Lightweight yet powerful, these portable hoists move many heavyweight tasks and can get into remote or difficult access sites. Examples: Setting utility poles, pulling wheeled equipment over obstacles, raising transformers (even over fences in back lots), hoisting heavy insulators, stringing and tensioning conductors, pulling cable indoors and underground. Simple technique eases all loads! So little effort is required, any crew member can run the hoist. Control is so accurate, loads can be moved fractions of an inch at a time. Example: 4 wraps of rope = 1:44 ratio. That is, 1 lb. pull on Fall Line develops 44 lb. on Load Line. Therefore, 20 lb. of pull develops 880 lb. of lift. OPTIONAL ROPE LOCK Automatically supports load when fall line is released, until operator resumes hoisting. The release lanyard permits lowering or lifting load with precise control over speed and distance. 3,000 LB. CAPSTAN 115VAC, Hydraulic, & Gasoline Powered Catalog Speed with Power source f/ Number Description 3,000 lb load 3,000 lb load Wgt C308-1370 115 VAC includes hoist and foot control only 12 ft per min. Min. 14 Amp 53 lb. C308-1380 Hydraulic drive hoist only (order switch separately) C308-0900 Hydraulic drive hoist with bayonet only (order switch sep) 30 feet per Min. 8 gal. per minute min. & 1000 psi 39 lb. C308-0940 Reversible Hydraulic Drive Hoist w/ Bayonet Adapt Only C308-1390 Gasoline drive hoist with foot throttle control only-not shown 11 ft. per min. Min. 8,000 rpm 54 lb.
HI-LINE UTILITY SUPPLY CO. 3,000 LB. HOIST OPTIONS 183 1 3 7 4 5 8 2 9 6 10 Ref. Cat. No. Description Weight 1 C308-0856 Rope Lock Device includes mounting bolts and washers 1.5 lb. 2 C308-1443 All-Purpose Bracket w/ 2 chain clamps for poles, angles, beams 30 lb. 3 E308-1434 Bolt Down Bracket (same as above except does not include chains) 15 lb. 4 E308-1334 Chain Clamp for all-purpose or bolt-down brackets; two required for use with bracket 7.5 lb. 5 C417-6145 Foot Control for 12 Volt DC hoist 5 lb. 6 C417-0337 Foot Control for 110 VAC and 230 VAC hoist 5 lb. 7 C308-0685 Foot Control for hydraulic hoists 17 lb. 8 E308-1362 Replacement Capstan Drum (does not include mounting bolt or washer) 5 lb. 9 C308-0820 Bayonet Adapter retrofits on hydraulic hoist; for collapsible reel or C417-0341 drum 7 lb. 10 C417-0341 Removable Capstan Drum for use on bayonet only 12 lb. GENERAL PURPOSE CAPSTAN Cat. No. 10727 This 7-1/4 x 8 high strength aluminum alloy, general purpose capstan will fit on any 2-7/16 diameter winch extension shaft equipped with a bayonet or pin type mount. is used for a wide variety of pulling and hoisting applications. Max Pull: 4,000 lbs. Wgt: 38 lbs.
184 HI-LINE UTILITY SUPPLY CO. 1,000 LB. CAPSTAN 12VDC, 115VAC, 230VAC, Hydraulic, & Gasoline Powered Catalog Speed with Power source f/ Wgt Number Description 1,000 lb load 1,000 lb load lbs C308-1172 12 VDC Hoist w/ foot switch, 25' cable, terms, relay 15 ft per min. Min. 110 amps 35 C308-1170 115 VAC Hoist w/ foot control switch only 40 ft per min. Min. 14 amps 35 C308-1171 230 VAC Hoist w/ foot control switch only 21 ft per min. Min. 7 amps 35 C308-1190 Gasoline Hoist w/ foot throttle control only 40 ft per min. 8,000 rpm 35 C308-1180 Hydraulic Hoist only 93 ft per min. 8 gal. per min. @1,000 psi 25 PORTABLE MATERIAL HANDLER for use with 1,000 LB. AC, Hydraulic, and Gasoline operated Hoists Where large vehicle-mounted equipment is impractical or cannot go, this portable system sets up fast. Lifts tools, apparatus, sets poles, moves materials in warehouse or store yard. Automatically takes up rope on reel and keeps line out of dirt. Mounts to wood, concrete or steel poles and angle member structures with one bracket and two chain clamps. Operator can keep all activity in view while controlling lift with tension -adjustment knob and hoist's foot control. Combine desired 1,000 lb. hoist with the following Ref Cat. No. Description Wgt. 14 C316-0760 Chassis only 37 lb. 15 C417-0343H Steel Reel with handle holds 20 lb. 1/2 x 600' or 3/8 x 1500' rope 6 C308-0925 Universal Bracket 8 lb. 5 C417-0346 Chain Clamps (two required) 7 lb. 15 14
HI-LINE UTILITY SUPPLY CO. 185 2 1,000 LB. HOIST OPTIONS 3 1 10 4 5 6 7 8 9 13 11 12 14 Ref. Cat. No. Description Weight 1 C308-0856 Rope Lock Device includes mounting bolts and washers 1.5 lb. 2 C308-1335 All-Purpose Bracket, includes 2- chains clamps; for poles, angles, beams 23 lb. 3 E308-1321 Bolt-Down Bracket (same as above except does not include chain clamps) 8 lb. 4 E308-1334 Chain Clamp for all-purpose or bolt-down brackets; two required for use with bracket 7.5 lb. 5 C417-0346 Chain Clamps for C308-0925 universal bracket only; two required for use w/ bracket 7 lb. 6 C308-0925 Universal Bracket only; for poles, angles, beams. Recommended for 1,000 lb. 8 lb. Gasoline Hoist and Material Handler. Also fits other 1,000 lb. & 750 lb. hoists 7 C417-6145 Foot Control for 12 Volt DC hoist 5 lb. 8 C417-0337 Foot Control for 110 Volt AC and 230 Volt AC hoist 5 lb. 9 C308-0685 Foot Control for hydraulic hoists 17 lb. 10 E308-1327 Replacement Capstan Drum does not include mounting bolt or washer 3 lb. 11 C308-0903 Swivel Bracket only 18 lb. 12 C308-0890 C-Bracket only complete with mounting bolts 5 lb. 13 C308-0909 Weather Shield with band clamp for 12 Volt DC hoist only 1 lb. 14 T308-0999 "Reese Hitch" Mounting Bracket Only (shown w/ #11, C308-0903 & #12 C308-0890) 16 lb.