CEILIN&WLL SYSTEMS etween us, ideas become reality XIOM CIRCLE & CURVED CNOPIES For Tegular 8 mm & MicroLook 8 mm reveal edge tiles I n s t allat ion u id e
P R E P R T I O N SUSPENSION POINTS Suspension points should be determined before installing the canopy. See the recommended suspension point matri on the last page of this manual. XIOM CIRCLE & CURVED CNOPIES - COMPONENTS* Item Nr. P 6406 Description iom Circle and Curved Profile P C0 Primary C-Channel P 304033 P 3403 Prelude Peakform Main Runner T5 or Prelude Peakform Main Runner T4 Initial recommendations iom Circle & Curved Canopies should always be installed in accordance with all applicable building codes and regulations. iom Circle & Curved Canopies, as any other architectural feature located in the ceiling plane, may obstruct or skew the eisting or planned fire sprinkler distribution pattern or even delay the activation of the fire detection system. Designers and installers are advised to consult a fire protection engineer for guidance on the proper installation techniques where fire detection or suppression systems are present. ny additional load (such as light spots) MUST NOT be suspended from the canopy but independently from the soffit. iom Circle & Curved Canopies should be always installed on a horizontal plane. iom Circle & Curved Canopies are only suitable for indoor applications. The iom Circle & Curved Canopies can reach a significant weight. In order to minimise the risk of injuries, the canopies should be installed by a minimum of people. Suspension elements such as threaded rods, anchors or any other element not included in the kit must be chosen to ensure a safe installation and follow local regulations. It is recommended to assemble the canopy under the final ceiling location to avoid later movement. P 30033 P 30 P WDN P 36 P 339 P 56 P 46 P 348 Prelude Cross Tee 600 mm T5 or Prelude Cross Tee 600 mm T4 T bar hanger Splice connector T-bar connector clip (Threaded) + M4 bolts (cross head) Perimeter fill-in for 5 mm grid Perimeter fill-in for 4 mm grid Channel bracket PC 97 Clamp for C-Channel loves supplied in the kit are used to prevent marking the components during installation. They are NOT meant to be used as safety gloves. * For further detailed information regarding any of these items please refer to the parts list included in the carton ll the profiles on the kits are cut and pre-drilled following the dimensions of the Canopy.
T E C S S I S o N T E F l o o R Choose the position of the perimeter section (roove facing up or downwards) * The.8.4 m module is used as an eample only Match the codes (-, -, etc) of the perimeter ends iom straight Profiles 4 iom curved Profiles 6 Splice connectors 3 T E P R I M R Y R I D o N T E F l o o R * The.8.4 m module is used as an eample only 3 C-Channels 6 T bar Connectors 6 angers OPTION 3 - ircraft cable OPTION - Quick hanger* OPTION - 6mm Threaded rod* * not included in the kit 3 4 Match the positioning stickers attached to the Chassis IMPORTNT NOTE: When there is not enough room for the screwdriver please install the T-bar connectors upside down. Self tapping screw to secure C-Channel position Check positioning arrow on the C-Channel 3
4 T E R I D M I N R U N N E R S I N T E I R * The.8.4 m module is used as an eample only Main Runners 4 T bar connectors 4 Perimeter fill in 3 4 Manoeuvre the plate until parallel to the grid Match the positioning stickers attached to the Chassis DO NOT TITEN YET 4
5 T E R I D C R O S S T E E S I N T E I R * The.8.4 m module is used as an eample only Manoeuvre the plate until parallel to the grid Match the positioning stickers attached to the Chassis DO NOT TITEN YET Special Cross Tees Standard Cross Tees 3 Standard Cross Tees 6 Special Cross tees 6 T bar Connectors 6 Perimeter fill in Use a measuring tape to check the centering of the Main Runners and Cross Tees and readjust if needed. Use self-tapping screws at the marked height line, once the Main Runner and Cross Tees have been centred. 6 T E T I L E S I N T E I R For Tegular 8 mm & MicroLook 8 mm edge reveal tiles ll perimeter tiles are cut on site (oard edge; see drawing page 3) and resting with the face on the iom Profile.. Cut down the perimeter tiles using the templates provided (See the layout below) and install them accordingly.. Install the full size/centre tile/s. Tile Layout * The.8.4 m module is used as an eample only C E D F F C D F.8m Dia Canopy PCSCI335 PCSCI334 E E D C.4m Dia Canopy PCSCI445 PCSCI444 F C E D I I Standard tiles (NOT INCLUDED) Set of templates I.8m.4m Canopy PCSCU435 PCSCU434 I I I.4m.4m Canopy PCSCU445 PCSCU444 3m 3m Canopy PCSCU555 PCSCU554 I.8m 3m Canopy PCSCU535 PCSCU534.4m 3m Canopy PCSCU545 PCSCU544 5
P04 Job No. 794 Produced by The Design Quorum 980 - March 0 E N E R L D T Material Frame: Etruded aluminum profiles rid & accessories: ot dipped galvanised steel Tiles: Mineral fibre tiles (NOT included in the kit) Surface finish Frame: Polyester powder coated rid capping: aked Polyester paint Color: rmstrong lobal White Recycled content Frame: 50% rid & accessories: 5% Tiles: Will vary depending on tiles installed. Contact your local rmstrong office for further information Warranty For more information, please contact rmstrong Technical Sales 0 400 800 Suspension points 500 500 500 500 00 0 400 400 00 00 900 00 00 00 Main Runner C Channel anger Point 4 pre-packed, ready-to-assemble iom Circle & Curved canopy kits, in 7 standard modules, will be available either in 5 mm or 4 mm grid Module rid system 5 mm XL rid system 4 mm XL Item Nr. Item Nr. Circle 800 PCS CI 33 5 PCS CI 33 4 Circle 400 PCS CI 44 5 PCS CI 44 4 Curved 400 800 PCS CU 43 5 PCS CU 43 4 Curved 400 400 PCS CU 44 5 PCS CU 44 4 Curved 0 800 PCS CU 53 5 PCS CU 53 4 Curved 0 400 PCS CU 54 5 PCS CU 54 4 Curved 0 0 PCS CU 55 5 PCS CU 55 4 iom Circle & Curved canopy kits are only available in specific markets, please contact rmstrong Technical Sales. Ceiling tiles RE NOT included in the kit. CENTRL EUROPE SOUT (L///CZ/R/U/KO/ MD/ME/MK/RO/RS/SK/SI) rmstrong uilding Products Lighthouse building Jankovcova 569/c 70 00 Praha 7 Czech Republic Tel. : +40 34 700 543 e-mail: service-ce@armstrong.com Czech Republic: www.armstrong.cz ungary: www.armstrong.co.hu Romania: www.armstrong.ro Serbia: www.armstrong.rs Slovakia: www.armstrong.sk Slovenia: www.armstrong.si dvisory note ll photographic and design elements supplied in this brochure do not necessarily reflect any recommendation by any of the companies named in this brochure as to the proper use or recommended methods of installation of suspended ceilings and are supplied only as informative material. For technical reasons in printing, differences may appear between colours printed in this brochure and the actual product. The choice of colours should always be made from a sample of the product. ll statements and technical information contained in this brochure, or any publication of the companies named in this brochure, relating to rmstrong ceilings are based on results obtained under laboratory test conditions. It is the responsibility of the user to verify with the seller of the products in writing that such statements and information are appropriate to the specific use intended. Sales of the products and liability of the selling companies are in accordance with the terms and conditions of sale of the selling company. ll product specifications are subject to modifications without prior notice.