Sliding Window Hardware Catalog TABLE OF CONTENTS

Connecting Innovations In Hardware With Windows, Patio Doors, And Skylights.

s l i di ng wi ndowhar dwar e c a t a l o g doubl ehung/s i ngl ehungpr oduc t s

Sliding Window Hardware Catalog TABLE OF CONTENTS Page No. Product Line / Description 1...700 Series - 700 Series Locks & Keepers 2...Recess Mount - Recess Mount Locks 3...7538 Series - Sash Lock & Keeper 4...9200 Series - Sash Lock & Keepers 5...17 Series - TrimLine Cam Locks 6...Misc. - TrimLine Cam Lock Keepers 7...9400 Series - Sash Lock 8...17 Series - EntryGard II Cam Lock 9...Misc. - EntryGard Cam Lock Keepers 10...17 Series - Sash Lock 11...17 Series - Button Lock 12...9850 Series - 9850 Series Quick-Snap Locks 13...9900 Series - 9900 Series Lock 14...9950 Series - 9950 Series Locks 15...30590 Series - Cam Gard Series Locks 16...17 Series - Restoration Lock 17...19 Series - Positive Action Lock (PAL) System 18...19 Series - Fusion System 19...Misc. - Tilt Latches 20...Misc. - Sash Lifts 21...Misc. - Window Rollers 22...Misc. - Pivot Bars 23...Misc. - Miscellaneous 24...Color Chart - Hardware Finishes

TRUTH HARDWARE S WARRANTY FOR WINDOW & DOOR MANUFACTURERS & AUTHORIZED DISTRIBUTORS All Truth Hardware products, with the exception of electrical products*, are warranted against defects in materials and workmanship for the life of the product. Industry related testing has defined the typical lifetime of fenestration hardware to be 10 years. Terms & Conditions of Sale defective in materials or workmanship, or negligently manufactured. This exclusive remedy shall not be deemed to have failed of its essential purpose so long as Truth Hardware is willing and able to repair or replace said defective products or parts in the prescribed manner. * All Truth Hardware electrical products, are warranted for one (1) year against defects in materials and workmanship. Truth Hardware s warranty is expressly limited to window & door manufacturers and Truth Hardware Authorized Distributors, who purchase Truth Hardware products for the purpose of resale, or use in the ordinary course of the buyers business, and may not be assigned or transferred. This warranty does not cover normal wear or discoloration on finishes, or any product which has been improperly installed, abused, misused, worn out, altered, used for a purpose other than that for which it was intended, or in a manner inconsistent with any instructions regarding its use, nor does it cover corrosion related damage. This warranty only covers electrical products that are used to drive manual hardware systems (operators and hinges) manufactured by Truth. THIS WARRANTY IS ECLUSIVE. TRUTH HARDWARE MAKES NO OTHER WARRANTY OF ANY KIND WHAT- SOEVER, EPRESSED OR IMPLIED, WITH RESPECT TO THE PRODUCTS MANUFACTURED AND SOLD BY IT, WHETHER AS TO MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR ANY OTHER MATTER. No agent, employee or representative of Truth Hardware has any authority to bind Truth Hardware to any affirmation, representation, or warranty concerning Truth Hardware products or parts, except stated herein. If any product manufactured by Truth Hardware is found to be defective by Truth Hardware, in its sole judgment, Truth Hardware will, at its option, either repair or replace such defective product. Truth s liability is limited only to the replacement value of the hardware. THIS REMEDY SHALL BE THE ECLUSIVE REMEDY AVAILABLE FOR ANY DEFECTS IN THE PRODUCTS MANUFACTURED AND SOLD BY TRUTH HARDWARE OR FOR DAMAGES RESULTING FROM ANY OTHER CAUSE WHATSOEVER, INCLUDING WITHOUT LIMITATION, TRUTH HARDWARE S NEGLIGENCE. TRUTH HARDWARE SHALL NOT IN ANY EVENT BE LIABLE TO ANY BUYER FOR CONSEQUENTIAL, OR INCIDENTAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR THE LABOR WHICH MAY BE REQUIRED FOR THE REPLACEMENT OF SAID PRODUCT, WHETHER FOR BREACH OF WARRANTY, NEGLIGENCE, ON THE BASIS OF STRICT LIABILITY, OR FOR ANY OTHER REASON. Terms - 1%/10 days - net 30 days on hardware purchases. Net 30 days on freight charges. Tooling invoice terms available upon request. Freight - F.O.B. Factory Conditions - Initial orders, and all subsequent orders placed before credit is established with Truth Hardware, will be on a cash-in-advance or C.O.D. basis. Cash-in-advance orders will be entered by Truth Hardware upon the receipt of the order and payment. Pricing is determined at time of shipment. Return Goods - Authorization from our Sales Department is required in advance for all goods to be returned to Truth Hardware. Authorization will be granted in all cases of defective product or incorrect shipments due to an error on Truth Hardwareís part. Truth Hardware may also, at its option, authorize the return of other goods subject to a 25% restocking charge and including and offsetting order equal in value to the amount of the return. Product considered for return must be standard product, built to current Truth Hardware manufacturing specifications, no older than the immediate past calendar year, clean, resalable, in full unopened cartons. The quantity to be returned cannot be excessive based on Truth Hardware s current level of sales and inventory position. Freight on all return goods must be prepaid to our plant and merchandise must be received within 30 days of date of authorization. The purpose of this exclusive remedy shall be to provide the window/door manufacturer, or Truth Hardware Authorized Distributor, with replacement of products, or parts, manufactured by Truth Hardware found to be

DOUBLE HUNG SLIDER 700 SERIES LOCKS Truth Hardware s new 700 Series Locks are by far the most exciting aesthetic changes that have hit the checkrail marketplace in years. There are four new designs within the 700 Series family of locks - each with its own distinct appearance. However, as unique as they each are to the eye, the similarities in quality features that the 700 Series have as a whole make these products the first family of check rail locks. FORGIVING CAM: The forgiving cam is likely the most valuable feature that the window manufacturers will realize. This patented new innovative design helps to insure proper engagement between the lock and keeper even on assemblies where these two components may be misaligned. The benefits of this forgiving cam can help to reduce field service calls down the road. SECURITY & RELIABILITY: The pick-resistant design of these locks helps you exceed forced entry requirements. POSITIVE SECURE ACTION: An improved detent in both the locking and unlocking motion of the handle, assures the homeowner that the cam has completed its travel. TIGHTER SEAL: By pulling meeting rails tightly together and by producing a better seal of the sash at the head and sill, the 700 Series Lock decreases air infiltration. These locks produce a.105 (2.7mm) lifting ability (Arc style lock has a.156 (4.0mm) lifting ability). And with their new slimmer handle design options, their low profile design helps assure maximum egress opening. An innovative spring design holds the handle in both the locked and unlocked positions while a concealed locking mechanism protects moving parts from dust and dirt for added lock life. INTERCHANGEABLE: Designed for 2.062" (52.4mm) centerto-center hole spacing on both the lock and keepers, the 700 Series Locks are interchangeable with existing designs making the move up to this new design virtually seamless. LOGO OPTIONS: For that personalized touch, most of Truth s 700 Series Check Rail Locks are capable of accepting your company s name or logo. Truth s unique custom print logo reproduction process is an attractive way of highlighting your company signature. For further details on the locks that accept this process, and where your company s logo would appear, please refer to the following drawings. WARRANTY: Protected under the terms of the Truth Warranty for Window & Door Manufacturers and Authorized Distributors. Refer to Truth s Terms & Conditions for further details. MATERIAL: High-pressure, corrosion-resistant, die-cast zinc. FINISH: Electrostatically applied, durable coatings that provide excellent resistance to chipping, scratching and corrosion while maintaining color stability for years in direct sunlight. Please refer to Truth s Color Chart for examples of Truth s most popular finish options. Truth also offers a wide range of decorative plated finishes - contact Truth for additional information on availability of these finishes on specific product lines. ORDERING INFORMATION: 1. Choose the 700 Series Lock style desired (specify by part number). 2. Order the appropriate Keeper to fit your lock and window profile (refer to drawings). 3. Specify finish number. 4. Select screws (fasteners). Sold separately. 4 - Phillips Flat Head Sheet Metal Screws. Refer to lock and keeper drawings for additional specs. (Length and thread type to be determined by profile) For further information on screw selection - see Truth Tips. LOW S LOCK ARC LOCK DELTA LP1 LOCK DELTA LP2 LOCK 1

700 SERIES LOCKS TRUTH TIPS: 1. When two locks are used on one window, the placement of each lock, with respect to its keeper, becomes very critical to maintain a constant weatherseal on all sides of the window and to insure that each lock engages properly with its keeper. 2. For accurate hardware placement in vinyl or metal applications, pre-drilling of the window profile is recommended. 3. For vinyl window applications, mounting screws should pass through two PVC walls, or one PVC wall and one insert wall. For this reason, it may be necessary to use a longer screw than is recommended. 4. For metal window profiles, Truth recommends stainless steel machine screws. However, in most applications, stainless steel sheet metal screws will provide adequate holding power. INCLUDE TRUTH SPECS ON YOUR NET WINDOW PROJECT Window check rail locks shall be included which will increase both security and weather seal tightness. The lock must provide easy operation and positive locked feel (detent). Window check rail locks will be of internal cam design to provide.062" (4.0 mm) of pull-in to aid in sealing the meeting rails. The lock and accompanying keeper will help insure proper engagement even on assemblies where these two components may be misaligned. The lock and keeper shall be constructed of high pressure zinc alloy die castings. Window locks shall be 700 Series Locks, as manufactured by Truth Hardware. FIG. 1 APPLICATION OF 700 SERIES CHECKRAIL LOCKS A B LOCKED POSITION 2.062 [52.4 mm] AREA AVAILABLE FOR CUSTOMER LOGO SURFACE MOUNT KEEPER APPLICATION GLASS CHECKRAIL FIG. 2 700 SERIES LOW LOCK FIG. 2 700 SERIES LOW S LOCK 2.812 [71.4 mm] FULL SCALE C 2.062 [52.4 mm] AREA AVAILABLE FOR CUSTOMER LOGO (QTY 2) #6 PHILLIPS FLAT HEAD SHEET METAL SCREW. (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 1a.365 [9.3 mm] 1.000 [25.4 mm].510 [13.0 mm] PRODUCT NUMBER A30700400 A30700401 A30700410 CAM PULL-IN:.117[2.9mm] AVAILABLE KEEPERS C30705 C30706 C30705 C30706 C30705 C30706 A.903 [22.9mm].888 [22.5mm].653 [16.6mm].638 [16.2mm].968 [24.6mm].953 [24.2mm] B.060 [1.5mm].060 [1.5mm] C.687 [17.4mm].437 [11.1mm].687 [17.4mm]

700 SERIES LOCKS FIG. FIG. 3 3 700 700 SERIES SERIES ARC ARC LOCK LOCK 2.700 [68.6 mm] C FULL SCALE (QTY 2) #7 PHILLIPS FLAT head SHEET METAL SCREWS. (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE.) 2.062 [52.4 mm].780 [19.8 mm] AREA AVAILABLE FOR CUSTOMER LOGO 1.125 [28.6 mm].480 [12.2 mm] PRODUCT NUMBER A30710400 A30710401 A30710402 A30710403 AVAILABLE KEEPERS C30715 C30716 C30715 C30716 C30715 C30716 C30715 C30716 CAM PULL-IN.070 [1.7mm].100 [2.5mm] A.903 [22.9mm].882 [22.4mm].653 [16.6mm].632 [16.1mm].873 [22.1mm].852 [21.6mm].623 [15.8mm].602 [15.2mm] B.060 [1.5mm].030 [.7mm] C.687 [17.4mm].437 [11.1mm].687 [17.4mm].437 [11.1mm] FIG. FIG. 44700 700 SERIES DELTA LP1 LOCK 2.812 [71.4 mm] FULL SCALE C.365 [9.3 mm] 2.062 [52.4 mm] AREA AVAILABLE FOR CUSTOMER LOGO 1.000 CAM PULL-IN:.117[2.9mm] [25.4 mm].589 [15.0 mm] PRODUCT NUMBER A30730400 A30730401 (QTY 2) #6 PHILLIPS FLAT HEAD SHEET METAL SCREWS. (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE.) AVAILABLE KEEPERS C30705 C30706 C30705 C30706 A.903 [22.9mm].888 [22.5mm].653 [16.6mm].638 [16.2mm] B.060 [1.5mm] C.687 [17.4mm].437 [11.1mm] FIG. 5 700 SERIES DELTA LP2 LOCK FIG. 5 700 SERIES DELTA LP2 LOCK C 2.812 [71.4 mm] FULL SCALE.365 [9.3 mm] 2.062 [52.4 mm] AREA AVAILABLE FOR CUSTOMER LOGO 1.000 CAM PULL-IN:.117[2.9mm] [25.4 mm] PRODUCT AVAILABLE A NUMBER KEEPERS.510 [13.0 mm] A30720400 A30720401 (QTY 2) #6 PHILLIPS FLAT HEAD SHEET METAL SCREWS. (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE.) C30705 C30706 C30705 C30706.903 [22.9mm].888 [22.5mm].653 [16.6mm].638 [16.2mm] B.060 [1.5mm] C.687 [17.4mm].437 [11.1mm] 1b

700 SERIES LOCKS FIG. 6 C 30705 CHECK RAIL LOCK KEEPER FIG. 7 C 30706 CHECK RAIL LOCK KEEPER FIG. 8 C 30715 CHECK RAIL LOCK KEEPER FIG. 9 C 30716 CHECK RAIL LOCK KEEPER 1c 700 west bridge street, owatonna, mn 55060 507.451.5620 800.866.7884 TRUTH.COM

DOUBLE HUNG SLIDER 7538 SASH LOCK AND KEEPER One of the most popular low profile locks on todays market: Streamlined low profile handle folds snugly against the housing producing a clean appearance, and helps to eliminate interference in shipping. One-piece box construction spring provides a strong detent in handle movement, thus assuring the homeowner that the handle has completed its travel. Three versions of latches are available (blade; snug fit latch; and hook latch - each of which have different throw and height dimensions (see drawings). 7538 latches are designed to be compatible with specific keepers that will help produce the optimum engagement between lock and keeper. LOGO OPTIONS: For that personalized touch, Truth s 7538 Series Sash Locks are capable of accepting your company s name or logo. Truth s logo process is an attractive way of highlighting your company signature. For further details on where your company s logo would appear, please refer to the following drawings. WARRANTY: Protected under the terms of the Truth Warranty for Window & Door Manufacturers & Authorized Distributors. Refer to Truth s Terms & Conditions for further details. MATERIAL: High-pressure, corrosion-resistant, die-cast zinc. FINISH: Electrostatically applied, durable coatings that provide excellent resistance to chipping, scratching and corrosion while maintaining color stability for years in direct sunlight. Please refer to Truth s Color Chart for examples of Truth s most popular finish options. Truth also offers a wide range of decorative plated finishes - contact Truth for additional information on availability of these finishes on specific product lines. ORDERING INFORMATION: 1. Choose the 7538 Series Lock that best meets your requirements (specify by item number found in Fig. 2-6). 2. Order the keeper style required. 3. Specify finish code (denoted where xx appears in the following drawings). Length and type of screw required determined by profile material used (sold separately). For additional information on screw selection - see Truth Tips. TRUTH TIPS: 1. A lock with a shorter throw should be used when the larger sweep radius of the.125 (3.2 mm) pull-in causes interference with the glazing or other areas of the profile. 2. When two locks are used on one window, the placement of each lock, with respect to its keeper, becomes very critical to maintain a constant weatherseal on all sides of the window and to insure that each lock engages properly with its keeper. 3. For accurate hardware placement in vinyl or metal applications, pre-drilling of the window profile is recommended. 4. For vinyl window applications, mounting screws should pass through two PVC walls, or one PVC wall and one insert wall. For this reason, it may be necessary to use a longer screw. 5. For metal window profiles, Truth recommends stainless steel machine screws. However, in most applications, stainless steel sheet metal screws will provide adequate holding power. INCLUDE TRUTH SPECS ON YOUR NET WINDOW PROJECT Window check rail locks shall be included which will increase both security and weather seal tightness. The lock must provide easy operation and positive locked feel. The lock and keeper shall be constructed of high pressure zinc alloy die castings. Window locks shall be 7538 Series as manufactured by Truth Hardware. 2

7538 SASH LOCK AND KEEPER FIG. 1 APPLICATION OF 7538 SERIES SASH LOCK AND KEEPER LOGO AREA LOGO AREA A LOCKED POSITION LOGO AREA SHOWN FULL SCALE GLASS CHECKRAIL GLASS FIG. 2 A07538120 SASH LOCK 2.900 [73.7 mm].390 [9.9 mm] 2.250 [57.2 mm].390 [9.9 mm] LOGO AREA.780 [19.8 mm] AVAILABLE LOGO AREA.713 [18.1 mm].199 [5.0 mm] 2a (QTY 2) #8 PHILLIPS FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE).410 [10.4 mm] AVAILABLE KEEPERS C07545 C08848 DIM A.060 (1.5mm)

7538 SASH LOCK AND KEEPER FIG. 3 A07538124 SASH LOCK 2.250 [57.2 mm].390 [9.9 mm].780 [19.8 mm] LOGO AREA AVAILABLE LOGO AREA 2.900 [73.7 mm].390 [9.9 mm].410 [10.4 mm].229 [5.8 mm].199 [5.0 mm] AVAILABLE KEEPERS C08245 C08849 C08452 DIM A.060 (1.5mm).713 [18.1 mm] (QTY 2) #8 PHILLIPS SLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) FIG. 4 A07538144 SASH LOCK.380 [9.7 mm].780 [19.8 mm] LOGO AREA AVAILABLE LOGO AREA 2.900 [73.7 mm] 2.250 [57.2 mm].390 [9.9 mm].210 [5.3 mm].199 [5.0 mm] AVAILABLE KEEPERS C08845 C09092 DIM A.060 (1.5mm).713 [18.1 mm].410 [10.4 mm] (QTY 2) #8 PHILLIPS SLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) FIG. 5 A07538231 SASH LOCK 2.900 [73.7 mm].500 [12.7 mm].780 [19.8 mm] LOGO AREA AVAILABLE LOGO AREA 2.250 [57.2 mm].390 [9.9 mm].120 [3.0 mm] AVAILABLE KEEPERS C07545 C08848 DIM A.060 (1.5mm) RECOMMENED SCREWS:.713 [18.1 mm].410 [10.4 mm] (QTY 2) #8 PHILLIPS SLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 2b

7538 SASH LOCK AND KEEPER FIG. 6 A07538186 SASH LOCK 2.250 [57.2 mm] 2.900 [73.7 mm] LOGO AREA.530 [13.5 mm].780 [19.8 mm] AVAILABLE KEEPERS C07545 CO8848 DIM A.060 (1.5mm).390 [9.9 mm] AVAILABLE LOGO AREA.200 [5.1 mm].488 [12.4 mm].410 [10.4 mm] (QTY 2) #8 PHILLIPS FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) FIG. 7 CO8452 KEEPER 2.900 [73.7 mm] AVAILABLE LOCKS DIM A.170 [4.3 mm] A07538124.060 (1.5mm) 2.250 [57.2 mm].410 [10.4 mm].205 [5.2 mm] (QTY 2) #6 PHILLIPS FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) FIG. 8 CO9092 KEEPER.125 [3.2 mm].250 [6.4 mm] AVAILABLE LOCKS DIM A A07538124.060 (1.5mm) 2.250 [57.2 mm].410 [10.4 mm] 2.900 [73.7 mm] (QTY 2) #4 PHILLIPS FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 2c 700 WEST BRIDGE STREET, OWATONNA, MN 55060 n 507.451.5620 800.866.7884 n TRUTH.COM

DOUBLE HUNG SLIDER 9200 SASH LOCK & KEEPERS The options available on Truth Hardware s 9200 Series Sash Locks are virtually endless. There are bases with or without alignment lugs which are helpful in preventing side shift of the sash (See Truth Tip #1). There are various mounting hole patterns from which to choose, which will ensure that your hardware is located in the most efficient location for optimum holding power (See Truth Tip #5). A variety of locking cams are available that help to pull meeting rails tightly together and will produce a better seal of the sash at the head and sill to help decrease air infiltration. Another reason for optional cam sizes is to help avoid potential interference created when the cam extends out to far. Refer to the following drawings to find the one which best meets your requirements. stability for years in direct sunlight. Please refer to Truth s Color Chart for examples of Truth s most popular finish options. Truth also offers a wide range of decorative plated finishes contact Truth for additional information on availability of these finishes on specific product lines. ORDERING INFORMATION: 1. Choose the 9200 Series Cam Lock style desired (specify by part number). 2. Specify finish number. 3. Specify Keeper to be ordered. 5. For vinyl window applications, mounting screws should pass through two PVC walls, or one PVC wall and one insert wall. For this reason, it may be necessary to use a longer screw than is recommended. 6. For metal window profiles, Truth recommends stainless steel machine screws. However, in most applications, stainless steel sheet metal screws will provide adequate holding power. INCLUDE TRUTH SPECS ON YOUR NET WINDOW PROJECT Window check rail locks shall be included which will increase both security and weather seal tightness. The lock must provide easy operation and positive locked feel. Based on window design, and the space allowed for mounting the window hardware some window systems are better suited for narrower keepers, or even facemounted varieties. The 9200 Series has a number of Top Mount, and Face Mount keepers to choose from. LOGO OPTIONS: For that personalized touch, Truth s 9200 Series Check Rail Locks are capable of accepting your company s name or logo. Truth s logo reproduction process is an attractive way of highlighting your company signature. For further details on where your company s logo would appear, please refer to the following drawings. WARRANTY: Protected under the terms of the Truth Warranty for Window & Door Manufacturers & Authorized Distributors. Refer to Truth s Terms & Conditions for further details. MATERIAL: High-pressure, corrosion-resistant, die-cast zinc. FINISH: Electrostatically applied, durable coatings that provide excellent resistance to chipping, scratching and corrosion while maintaining color Types of screws required determined by material of profile used (sold separately). For additional information on screw selection - see Truth Tips. TRUTH TIPS: 1. A lock with pick-resistant alignment nibs should be used whenever possible. A lock without nibs should be chosen when the lugs cause interference with divided light grills or other window features. 2. A lock with a small cam should be used when the larger sweep radius of the.125 (3.2 mm) pull-in cam causes interference with the glazing or other areas of the profile. A face-mounted keeper is usually required. 3. When two locks are used on one window, the placement of each lock, with respect to its keeper, becomes very critical to maintain a constant weatherseal on all sides of the window and to insure that each lock engages properly with its keeper. 4. For accurate hardware placement in vinyl or metal applications, pre-drilling of the window profile is recommended. Window check rail locks will be of internal cam design to provide optimum pull-in to aid in sealing the meeting rails. The lock and accompanying keeper will prevent misalignment during locking. The lock and keeper shall be constructed of high pressure zinc alloy die castings. Window locks shall be 9200 Series locks as manufactured by Truth Hardware. 3

9200 SASH LOCK & KEEPERS FIG. 1 SASH LOCK AND KEEPER 2.836 [72.0 mm] NIBS NESTING NIBS A 1.000 [25.4 mm] LOGO AREA NO NIBS SHOWN RIGHT HAND SHOWN B LOGO AREA.735 [18.7 mm] AVAILABLE LOGO AREA LOGO AREA SHOWN FULL SCALE.470 [11.9 mm] HANDING NIBS 3a PART NUMBER A09200400 A09200401 A09200402 A09200407 A09200409 A09200411 A09200412 A09200416 A09200417 A09200420 A09200427 A09200430 A09200432 A09200441 A09200457 A09200520 A09200537 A09200580 A09200599 "A" DIMENSION 0.390 (9.9mm) 0.390 (9.9mm) 0.437 (11.1mm) 0.687 (17.4mm) 0.687 (17.4mm) 0.719 (18.3mm) 0.437 (11.1mm) 0.437 (11.1mm) 0.687 (17.4mm) 0.687 (17.4mm) 0.687 (17.4mm) 0.390 (9.9mm) 0.390 (9.9mm) 0.437 (11.1mm) 0.437 (11.1mm) 0.687 (17.4mm) 0.687 (17.4mm) 0.687 (17.4mm) 0.719 (18.3mm) "B" DIMENSION 2.250 (57.2mm) 2.250 (57.2mm) 2.062 (52.4mm) 2.062 (52.4mm) 2.062 (52.4mm) 2.156 (54.8mm) 2.062 (52.4mm) 2.062 (52.4mm) 2.062 (52.4mm) 2.062 (52.4mm) 2.062 (52.4mm) 2.250 (57.2mm) 2.250 (57.2mm) 2.250 (57.2mm) 2.250 (57.2mm) 2.062 (52.4mm) 2.062 (52.4mm) 2.062 (52.4mm) 2.156 (54.8mm) RH LH NO NIBS NIBS NESTING NIBS # 8 SCREW # 8 SCREW # 6 SCREW # 6 SCREW # 6 SCREW # 8 SCREW # 6 SCREW # 6 SCREW # 6 SCREW # 6 SCREW # 6 SCREW # 8 SCREW # 8 SCREW # 8 SCREW # 8 SCREW # 6 SCREW # 6 SCREW.187 DIA. RIVET # 6 SCREW * ALL SCREWS ARE TO BE PHILLIPS FLAT HEAD. (LENGTH AND TYPE TO BE DETERMINED BY PROFILE) RECOMMENDED SCREWS * CAM REACH 0.06 (1.5mm) 0.06 (1.5mm) 0.06 (1.5mm) 0.06 (1.5mm) 0.06 (1.5mm) 0.06 (1.5mm) 0.06 (1.5mm) NO PULL-IN NO PULL-IN 0.06 (1.5mm) 0.06 (1.5mm) 0.06 (1.5mm) 0.06 (1.5mm) 0.06 (1.5mm) 0.06 (1.5mm) 0.06 (1.5mm) 0.06 (1.5mm) 0.06 (1.5mm) 0.06 (1.5mm)

9200 SASH LOCK & KEEPERS FIG. 2 LOCK/KEEPER COMPATIBILITY TABLES "B" DIMENSION (HOLE CENTER TO HOLE CENTER-LOCK TO KEEPER) LOCKS A09200407 A09200402 A09200401 A09200400 A09200416 A09200412 A09200411 A09200409 A09200441 A09200432 A09200430 A09200427 A09200420 A09200417 A09200599 A09200580 A09200537 A09200520 A09200457 C08924.60.60.93.65.65.90.90.60.65.65.90.90.93 SURFACE MOUNT KEEPERS C09022 C09145 C09256 C09335 C09336 C09452 C09717 C09968 C30022.60.57.58.64.59.64.64.90.87.87.57.79 1.08.60.89.92.64.64.87.90.62.62.87.89.89.89.89.59.59.59.64.89.59.87.57.62.89.93.65.65.90.90.60.65.89.64.89.89.89.62.87.65.90.89.92.87.90.90.93 KEEPER CENTER OF SCREW C B D SASH LOCK SURFACE MOUNT KEEPER LOCATION FACE MOUNT KEEPER LOCATION LOCKS A09200400 DIMENSION A09200409 A09200411 A09200412 A09200416 A09200417 A09200427 A09200430 A09200441 A09200457 A09200520 A09200580 A09200599 C09062 C D 0.63 1.08 0.93 1.08 0.96 1.08 0.68 1.08 0.66 1.08 0.91 1.08 0.93 1.06 0.63 1.08 0.68 1.08 0.68 1.08 0.93 1.08 0.93 1.08 0.96 1.12 FACE MOUNT KEEPERS C09312 C09391 C09659 C09697 C D C D C D C D 0.40 0.50 0.65 0.32 0.65 0.85 0.70 0.50 0.95 0.32 0.95 0.85 0.73 0.50 0.98 0.32 0.98 0.85 0.50 0.50 0.70 0.32 0.70 0.85 0.48 0.50 0.68 0.32 0.68 0.85 0.68 0.50 0.93 0.32 0.93 0.85 0.70 0.48 0.95 0.30 0.95 0.83 0.40 0.50 0.65 0.32 0.65 0.85 0.45 0.50 0.70 0.32 0.70 0.85 0.45 0.50 0.70 0.32 0.70 0.85 0.70 0.50 0.95 0.32 0.95 0.85 0.70 0.50 0.95 0.32 0.95 0.85 0.73 0.52 1.08 0.22 0.98 0.35 0.98 0.89 C09906 C D 1.08 0.22 3b

9200 SASH LOCK & KEEPERS FIG. 3 C08924 KEEEPER.160 [4.1 mm] RECOMMENED SCREWS: 2.124 [53.9 mm] 2.840 [72.1 mm] (QTY 2) #6 PHILLIPS FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE).320 [8.1 mm].460 [11.7 mm] AVAILABLE LOCKS LOCK PART NUMBER A09200400 A09200409 A09200411 A09200412 A09200416 A09200417 A09200427 A09200430 A09200441 A09200457 A09200520 A09200580 A09200599 "B" SEE FIG. 2 0.60 (15.2mm) 0.60 (15.2mm) 0.93 (23.5mm) 0.65 (16.5mm) 0.65 (16.5mm) 0.90 (22.9mm) 0.90 (22.9mm) 0.60 (15.2mm) 0.65 (16.5mm) 0.65 (16.5mm) 0.90 (22.9mm) 0.90 (22.9mm) 0.93 (23.5mm) FIG. 4 C09335 KEEPER 2.250 [57.2 mm].136 [3.5 mm].280 [7.1 mm] 2.840 [72.1 mm].480 [12.2 mm] AVAILABLE LOCKS (QTY 2) #6 SCREW WITH A #5 HEAD (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE.) LOCK PART NUMBER A09200402 A09200420 A09200432 A09200537 "B" SEE FIG. 2 0.64 (16.3mm) 0.89 (22.6mm) 0.59 (15.0mm) 0.89 (22.6mm) 3c

9200 SASH LOCK & KEEPERS FIG. 5 C09452 KEEEPER 2.060 [52.3 mm].280 [7.1 mm] 2.120 [3.0 mm].140 [3.6 mm] 2.840 [72.1 mm].480 [12.2 mm] AVAILABLE LOCKS (QTY 2) #6 SCREW WITH A #5 HEAD (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE.) LOCK PART NUMBER A09200402 A09200420 A09200432 A09200537 "B" SEE FIG. 2 0.64 (16.3mm) 0.89 (22.6mm) 0.59 (15.0mm) 0.89 (22.6mm) FIG. 6 C09717 KEEPER.250 [6.4 mm].528 [13.4 mm] 2.250 [57.2 mm] 2.840 [72.1 mm].120 [3.0 mm] 2.150 [3.8 mm] (QTY 2) #6 PHILLIPS FLAT HEAD SCREWS. (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE.).303 [7.7 mm] LOCK PART NUMBER A09200400 A09200409 A09200411 A09200412 A09200416 A09200417 A09200427 A09200430 A09200441 A09200457 A09200520 A09200580 A09200599 AVAILABLE LOCKS "B" SEE FIG. 2 0.57 (14.5mm) 0.87 (22.1mm) 0.90 (22.9mm) 0.62 (15.7mm) 0.62 (15.7mm) 0.87 (22.1mm) 0.87 (22.1mm) 0.57 (14.5mm) 0.62 (15.7mm) 0.62 (15.7mm) 0.87 (22.1mm) 0.87 (22.1mm) 0.90 (22.9mm) 3d

9200 SASH LOCK & KEEPERS FIG. 7 C09336 KEEPER 2.202 [55.9 mm].140.280 [3.6 mm] [7.1 mm] 2.840 [72.1 mm] (QTY 2) #6 PHILLIPS FLAT HEAD SCREWS. (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE.) 2.266 [6.8 mm].480 [12.2 mm] LOCK PART NUMBER A09200400 A09200402 A09200409 A09200411 A09200412 A09200416 A09200417 A09200420 A09200427 A09200430 A09200432 A09200441 A09200457 A09200520 A09200537 A09200580 A09200599 AVAILABLE LOCKS "B" SEE FIG. 2 0.59 (15.0mm) 0.64 (16.3mm) 0.89 (22.6mm) 0.92 (23.4mm) 0.64 (16.3mm) 0.64 (16.3mm) 0.89 (22.6mm) 0.89 (22.6mm) 0.89 (22.6mm) 0.59 (15.0mm) 0.59 (15.0mm) 0.64 (16.3mm) 0.64 (16.3mm) 0.89 (22.6mm) 0.89 (22.6mm) 0.89 (22.6mm) 0.92 (23.4mm) FIG. 8 C030022 KEEPER.300 [7.6 mm].505 [12.8 mm] 2.186 [55.5 mm] 2.840 [72.1 mm] (QTY 2) #6 PHILLIPS FLAT HEAD SCREWS. (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE.).150 [3.8 mm] 2.251 [6.4 mm].300 [7.6 mm] LOCK PART NUMBER A09200400 A09200409 A09200411 A09200412 A09200416 A09200417 A09200427 A09200430 A09200441 A09200457 A09200520 A09200580 A09200599 AVAILABLE LOCKS "B" SEE FIG. 2 0.60 (15.2mm) 0.89 (22.6mm) 0.93 (23.5mm) 0.65 (16.5mm) 0.65 (16.5mm) 0.90 (22.9mm) 0.90 (22.9mm) 0.60 (15.2mm) 0.65 (16.5mm) 0.65 (16.5mm) 0.90 (22.9mm) 0.90 (22.9mm) 0.93 (23.5mm) 3e

9200 SASH LOCK & KEEPERS FIG. 9 C09022 KEEPER 2.250 [57.2 mm].160 [4.1 mm].320 [8.1 mm] 2.090 [2.3 mm].473 [12.0 mm] 2.840 [72.1 mm] AVAILABLE LOCKS (QTY 2) #8 PHILLIPS FLAT HEAD SCREWS. (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE.) LOCK PART NUMBER A09200401 A09200407 "B" SEE FIG. 2 0.60 (15.2mm) 0.90 (22.9mm) FIG. 10 C09968 KEEPER 2.062 [52.4 mm].344 [8.7 mm].516 [13.1 mm].278 [7.1 mm].500 [12.7 mm] 2.840 [72.1 mm] AVAILABLE LOCKS (QTY 2) #6 PHILLIPS FLAT HEAD SCREWS. (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE.) LOCK PART NUMBER A09200401 A09200407 "B" SEE FIG. 2 0.79 (20.1mm) 1.08 (27.4mm) 3f

9200 SASH LOCK & KEEPERS FIG. 11 C09145 KEEPER 2.156 [54.8 mm].123 [3.1 mm].250 [6.4 mm].275 [7.0 mm].460 [11.7 mm] 2.840 [72.1 mm] (QTY 2) #8 PHILLIPS FLAT HEAD SCREWS. (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE.) AVAILABLE LOCKS LOCK PART NUMBER A09200401 A09200407 "B" SEE FIG. 2 0.57 (14.5mm) 0.87 (22.1mm) FIG. 12 C09256 KEEPER 2.250 [57.2 mm].123 [3.1 mm].250 [6.4 mm].505 [12.8 mm] 2.840 [72.1 mm] AVAILABLE LOCKS LOCK PART NUMBER "B" SEE FIG. 2 (QTY 2) #6 PHILLIPS FLAT HEAD SCREWS. (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE.) A09200401 A09200407 0.57 (14.5mm) 0.87 (22.1mm) 3g

9200 SASH LOCK & KEEPERS FIG. 13 C09659 FACE MOUNT KEEPER 1.500 [38.1 mm] AVAILABLE LOCKS LOCK PART NUMBER A09200400.190 [4.8 mm] A09200409 A09200411.289 [7.3 mm] A09200412 A09200416 A09200417.397 [10.1 mm] 1.000 [25.4 mm].270 [6.9 mm].093 [2.4 mm].160 [4.1 mm] A09200427 A09200430 A09200441 A09200457 A09200520 (QTY 2) #6 PHILLIPS FLAT HEAD SCREWS. (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE.) A09200580 A09200599 FIG. 14 C09312 FACE MOUNT KEEPER 1.750 [44.4 mm] AVAILABLE LOCKS LOCK PART NUMBER A09200400 A09200409.406 [10.3 mm].150 [3.8 mm] 1.326 [33.7 mm] A09200411 A09200412 A09200416 A09200417 A09200427.875 [22.2 mm].467 [11.9 mm].070 [1.8 mm] A09200430 A09200441 A09200457 A09200520 (QTY 2) #6 PHILLIPS FLAT HEAD SCREWS. (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE.) A09200580 A09200599 3h

9200 SASH LOCK & KEEPERS FIG. 15 C09697 FACE MOUNT KEEPER 1.500 [38.1 mm] AVAILABLE LOCKS LOCK PART NUMBER.397 [10.1 mm].190 [4.8 mm] A09200400 A09200409 A09200411 A09200412.944 [24.0 mm].828 [21.0 mm] 1.575 [40.0 mm] A09200416 A09200417.217 [5.5 mm].434 [11.0 mm].093 [2.4 mm] A09200427 A09200430 A09200441 A09200457 A09200520 (QTY 2) #6 PHILLIPS FLAT HEAD SCREWS. (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE.) A09200580 A09200599 FIG. 16 C09062 FACE MOUNT KEEPER AVAILABLE LOCKS.250 [6.4 mm] 1.500 [38.1 mm] LOCK PART NUMBER A09200400.250 [6.4 mm].250 [6.4 mm] A09200409 A09200411 A09200412.452 [11.5 mm] 1.562 [39.7 mm] 1.750 [44.4 mm] A09200416 A09200417 A09200427 A09200430 1.000 [25.4 mm].070 [1.8 mm].090 [2.3 mm] A09200441 A09200457 A09200520 (QTY 2) #6 PHILLIPS PAN HEAD SCREWS. (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE.) A09200580 A09200599 3i

9200 SASH LOCK & KEEPERS FIG. 17 C09391 FACE MOUNT KEEPER AVAILABLE LOCKS 2.800 [71.1 mm] LOCK PART NUMBER A09200400 A09200409.320 [8.1 mm] 2.062 [52.4 mm].370 [9.4 mm] A09200411 A09200412 A09200416 A09200417.185 [4.7 mm] (QTY 2) #6 PHILLIPS FLAT HEAD SCREWS. (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE.) 2.265 [6.7 mm] A09200427 A09200430 A09200441 A09200457 A09200520 A09200580 A09200599 FIG. 18 C09906 FACE MOUNT KEEPER.322 [8.2 mm] 2.750 [69.8 mm] AVAILABLE LOCKS LOCK PART NUMBER A09200400 A09200409 A09200411 2.052 [52.1 mm] 5.0 A09200412 A09200416 A09200417.185 [4.7 mm] 2.221 [5.6 mm] (QTY 2) #6 PHILLIPS FLAT HEAD SCREWS. (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE.).370 [9.4 mm] A09200427 A09200430 A09200441 A09200457 A09200520 A09200580 A09200599 3j

9200 SASH LOCK & KEEPERS FIG. 19 41434 FACE MOUNT KEEPER.117 [3.0 mm] 1.994 [50.6 mm].275 [7.0 mm] 1.041 [26.4 mm].151 [3.8 mm] 1.000 [25.4 mm] 1.500 [38.1 mm].244 [6.2 mm].250 [6.4 mm].195 [5.0 mm] FIG. 20 41405 KEEPER 2.050 [52.1 mm].125 [3.2 mm] AVAILABLE LOCKS A A09200666.872 (22.1mm).060 (1.5mm) B.269 [6.8 mm].442 [11.2 mm] 2.587 [65.7 mm].250 [6.4 mm] (QTY2) #6 SHEET METAL SCREWS PHILLIPS FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 3k 700 WEST BRIDGE STREET, OWATONNA, MN 55060 n 507.451.5620 800.866.7884 n TRUTH.COM

DOUBLE HUNG SLIDER 17 TRIMLINE CAM LOCK By pulling meeting rails tightly together and by producing a better seal of the sash at the head and sill, the TrimLine TM Cam Lock decreases air infiltration. And with its new slimmer handle design, its low profile design helps assure maximum egress opening. An innovative spring design holds the handle in both the locked and unlocked positions while a concealed locking mechanism protects moving parts from dust and dirt for added lock life, too. For locks designed with alignment lugs, a positive sash alignment feature prevents side shift of the sash. An improved detent in both the locking and unlocking motion of the handle, assures that the cam has completed its travel. Designed for #6 mounting screws on 2.062 (52.4mm) center-tocenter hole spacing on both the lock and keepers. This lock produces a.125 (3.2mm) pull-in {.062 (1.6mm) with small cam} with a.156 (4.0mm) lifting ability. SECURITY & RELIABILITY: The pick-resistant design of this lock helps you exceed the load requirements for AAMA 1302.5 Forced Entry Resistance Test, the California Model Building Security Ordinance and ASTM-588 Forced Entry Test. LOGO OPTIONS: For that personalized touch, Truth s TrimLine Check Rail Locks are capable of accepting your company s name or logo. Truth s unique custom print logo reproduction process is an attractive way of highlighting your company signature. For further details on where your company s logo would appear, please refer to the following drawings. WARRANTY: Protected under the terms of the Truth Warranty for Window & Door Manufacturers and Authorized Distributors. Refer to Truth s Terms & Conditions for further details. MATERIAL: High-pressure, corrosion-resistant, die-cast zinc. FINISH: Electrostatically applied, durable coatings that provide excellent resistance to chipping, scratching and corrosion while maintaining color stability for years in direct sunlight. Please refer to Truth s Color Chart for examples of Truth s most popular finish options. Truth also offers a wide range of decorative plated finishes - contact Truth for additional information on availability of these finishes on specific product lines. ORDERING INFORMATION: 1. Choose the TrimLine Cam Lock style desired (specify by part number). 2. Specify finish number. 3. Select mounting hardware (sold separately): For Keeper styles, refer to TrimLine(tm) Keeper catalog page for styles and part numbers. Types of screws required determined by material of profile used. Refer to drawings for complete information on screw type and quantity needed (sold separately). For additional information on screw selection - see Truth Tips. TRUTH TIPS: 1. A lock with pick-resistant alignment lugs should be used whenever possible. A lock without lugs should be chosen when the lugs cause interference with divided light grills or other window features. 2. A lock with a small cam should be used when the larger sweep radius of the.125 (3.2mm) pull-in cam causes interference with the glazing or other areas of the profile. A face-mounted keeper is usually required. 3. When two locks are used on one window, the placement of each lock, with respect to its keeper, becomes very critical to maintain a constant weatherseal on all sides of the window and to insure that each lock engages properly with its keeper. 4. For accurate hardware placement in vinyl or metal applications, pre-drilling of the window profile is recommended. 5. For vinyl window applications, mounting screws should pass through two PVC walls, or one PVC wall and one insert wall. For this reason, it may be necessary to use a longer screw than is recommended. 6. For metal window profiles, Truth recommends stainless steel machine screws. However, in most applications, stainless steel sheet metal screws will provide adequate holding power. INCLUDE TRUTH SPECS ON YOUR NET WINDOW PROJECT Window check rail locks shall be included which will increase both security and weather seal tightness. The lock must provide easy operation and positive locked feel (detent). Window check rail locks will be of internal cam design to provide.125 (3.2mm) of pull-in to aid in sealing the meeting rails. The lock and accompanying keeper will prevent mis-alignment during locking. The lock and keeper shall be constructed of high pressure zinc alloy die castings. Window locks shall be 17 series TrimLine, as manufactured by Truth Hardware, Owatonna, MN. 4

17 TRIMLINE CAM LOCK FIG. 1 APPLICATION OF TRIMLINE CHECK RAIL LOCK 2.062 [52.4 mm] A 1.032 [26.2 mm] 2.594 [65.9 mm] TOP MOUNTED KEEPER 1.616 [41.0 mm] GLASS.777 [19.7 mm] D.442 [11.2 mm] CHECKRAIL FACE MOUNTED KEEPER TOP AREA FRONT AREA "CUSTOM PRINT" LOGO AREAS AVAILABLE (FULL SCALE) WOOD: (QTY 2) (P/N 19050) #6.750 PHILLIPS, FLAT HEAD, SHEET METAL SCREWS. PVC/METAL: (QTY 2) #6 PHILLIPS, FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) FIG. 2 TRIMLINE CHECK RAIL LOCK OPTIONS ALIGNMENT LUGS CAM PRODUCT NUMBER 17.32 B.438 (11.1mm) WITH LUGS WITHOUT LUGS LARGE CAM SMALL CAM SPECIAL FEATURES 17.33.688 (17.5mm) B 17.34 17.35.438 (11.1mm).688 (17.5mm) 2.062 [52.4 mm] NOTE: LARGE CAM HAS.125 PULL-IN. SMALL CAM HAS.062 PULL-IN. 17.38 17.39 17.40 17.41 17.43.438 (11.1mm).688 (17.5mm).438 (11.1mm).688 (17.5mm).438 (11.1mm) OPPOSITE HAND 4a 700 west bridge street, owatonna, mn 55060 507.451.5620 800.866.7884 TRUTH.COM

DOUBLE HUNG SLIDER 17 TRIMLINE CAM LOCK KEEPERS Truth realizes that each profile in the marketplace today may require its own particular Keeper due to the variety of mounting application possibilities. Because of this, Truth has developed a wide variety of Keepers for our TrimLine TM Cam Lock whose shapes and styles were designed to help satisfy these needs. The TrimLine TM Cam Lock Keepers in the accompanying drawings should provide you with all of the technical information you should require. However, if you wish further technical assistance in selecting a Keeper, please contact Truth. WARRANTY: Protected under the terms of the Truth Warranty for Window & Door Manufacturers & Authorized Distributors. Refer to Truth s Terms & Conditions for further details. TRUTH TIPS 1. For accurate hardware placement in vinyl or metal applications, pre-drilling of the window profile is recommended. 2. For vinyl window applications, mounting screws should pass through two PVC walls, or one PVC wall and one insert wall. For this reason, it may be necessary to use a longer screw than is recommended. 3. For metal window profiles, Truth recommends stainless steel machine screws. However, in most applications, stainless steel sheet metal screws will provide adequate holding power. MATERIAL: High-pressure, corrosion-resistant die-cast zinc. FINISH: Electrostatically applied, durable coatings that provide excellent resistance to chipping, scratching and corrosion while maintaining color stability for years in direct sunlight. Please refer to Truthís Color Chart for examples of Truth s most popular finish options. Truth also offers a wide range of decorative plated finishes contact Truth for additional information on availability of these finishes on specific product lines. ORDERING INFORMATION: 1. Order Keepers by part number. Refer to lock section for details on A and D dimensions. 2. Specify finish number. 5

17 TRIMLINE CAM LOCK KEEPERS FIG. 1 40368. KEEPER.330 [8.4 mm] 2.062 [52.4 mm].174 [4.4 mm].536 [13.6 mm] WOOD: (QTY 2) (P/N 19050) #6.750 PHILLIPS FLAT HEAD, SHEET METAL SCREWS PVC/METAL: (QTY 2) #6 PHILLIPS, FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO DETERMINED BY PROFILE) 2.593 [65.9 mm] AVAILABLE LOCKS A 17.32.610 (15.5mm) 17.33 17.34 17.35.860 (21.8mm).610 (15.5mm).860 (21.8mm) FIG. 2 40380. KEEPER.153 [3.9 mm] 2.062 [52.4 mm].309 [7.8 mm].442 [11.2 mm] WOOD: (QTY 2) (P/N 19050) #6.750 PHILLIPS FLAT HEAD, SHEET METAL SCREWS PVC/METAL: (QTY 2) #6 PHILLIPS, FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO DETERMINED BY PROFILE) 2.594 [65.9 mm] AVAILABLE LOCKS A 17.32.610 (15.5mm) 17.33 17.34 17.35.860 (21.8mm).610 (15.5mm).860 (21.8mm) FIG. 3 40904. KEEPER 2.062 [52.4 mm].156 [4.0 mm].312 [7.9 mm].442 [11.2 mm] 5a WOOD: (QTY 2) (P/N 19050) #6.750 PHILLIPS FLAT HEAD, SHEET METAL SCREWS PVC/METAL: (QTY 2) #6 PHILLIPS, FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO DETERMINED BY PROFILE) 2.586 [65.7 mm] AVAILABLE LOCKS A 17.38.610 (15.5mm) 17.39 17.40 17.41 17.43.860 (21.8mm).610 (15.5mm).860 (21.8mm).610 (15.5mm)

17 TRIMLINE CAM LOCK KEEPERS FIG. 4 40375. TRIMLINE KEEPER.182 [4.6 mm] 1.510 [38.4 mm] D 1.037 [26.4 mm] NOTE: LOCKS WITH LARGER CAM MAY INTERFERE WITH GLASS.436 [11.1 mm] WOOD: (QTY 2) #10.750 PHILLIPS PAN HEAD, SHEET METAL SCREWS PVC/METAL: (QTY 2) #10 PHILLIPS, PAN HEAD SCREWS (LENGTH AND THREAD TYPE TO DETERMINED BY PROFILE).170 [4.3 mm].453 [11.5 mm].100 [2.5 mm] AVAILABLE LOCKS ALL TRIMLINE LOCKS D.864 (21.8mm) FIG. 5 41298. TRIMLINE KEEPER 1.770 [45.0 mm].500 [12.7 mm] D E.182 [4.6 mm].170 [4.3 mm] NOTE: LOCKS WITH LARGER CAM MAY INTERFERE WITH GLASS WOOD: (QTY 2) (P/N 19050) #6.750 PHILLIPS FLAT HEAD, SHEET METAL SCREWS PVC/METAL: (QTY 2) #6 PHILLIPS, FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO DETERMINED BY PROFILE) 1.000 [25.4 mm] AVAILABLE LOCKS ALL TRIMLINE LOCKS.090 [2.3 mm] D 1.062 (27.0mm) E.562 (14.3mm) FIG. 6 40670. TRIMLINE KEEPER 1.749 [44.4 mm].156 [4.0 mm] D 1.317 [33.5 mm] WOOD: (QTY 2) (P/N 19050) #6.750 PHILLIPS FLAT HEAD, SHEET METAL SCREWS.876 [22.3 mm] PVC/METAL: (QTY 2) #6 PHILLIPS, FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO DETERMINED BY PROFILE).312 [7.9 mm] NOTE: LOCKS WITH LARGER CAM MAY INTERFERE WITH GLASS AVAILABLE LOCKS 17.38 17.39 17.40 17.41 17.43 D.348 (8.9mm) 5b

17 TRIMLINE CAM LOCK KEEPERS FIG. 7 45076. KEEPER (narrow flat base) 2.156 [54.8 mm].125 [3.2 mm].265 [6.7 mm] 2.594 [65.9 mm].442 [11.2 mm] WOOD: (QTY 2) #6 WITH A #5 HEAD.750 PHILLIPS FLAT HEAD, SHEET METAL SCREWS. PVC/METAL: (QTY 2) #6 WITH A #5 HEAD PHILLIPS, FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO DETERMINED BY PROFILE) AVAILABLE LOCKS 17.39 17.40 A.812 (20.6mm).562 (14.3mm) FIG. 8 45184. KEEPER (narrow flat base) 2.062 [52.4 mm].125 [3.2 mm].250 [6.4 mm] 2.594 [65.9 mm] WOOD: (QTY 2) #6 WITH A #4 HEAD.750 PHILLIPS FLAT HEAD, SHEET METAL SCREWS. PVC/METAL: (QTY 2) #6 WITH A #4 HEAD PHILLIPS, FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO DETERMINED BY PROFILE).457 [11.6 mm] AVAILABLE LOCKS 17.33 17.34 A.828 (21.0mm).578 (14.7mm) 5c 700 WEST BRIDGE STREET, OWATONNA, MN 55060 n 507.451.5620 800.866.7884 n TRUTH.COM

DOUBLE HUNG SLIDER 9400 SASH LOCK & KEEPERS One of the most popular locking designs in the slider and single/double-hung markets, Truth Hardware s 9400 Series Sash Lock is one of the most reliable products available. Concealed locking mechanisms help protect moving parts from dust and dirt for added lock life while producing a better seal of the sash at the head and sill. The internal cam eliminates unsightly paint abrasions caused by the interaction of cam and keeper. The internal cam s are handed and come in various sizes that relate to the amount of pull-in/reach-out and sash lift. These lock-up characteristics produce a better seal of the sash at the head and sill to help decrease air infiltration. The location of the mounting holes on the base are designed to secure the lock in a position along the check rail which affords the most holding power (See Truth Tip #4). These locks are available with or without alignment lugs. These lugs have been designed to help prevent shifting of the rails during locking for an enhanced window seal. Tapered nesting lugs, which help guide the lock to the keeper are also an option. WARRANTY: Protected under the terms of the Truth Warranty for Window & Door Manufacturers & Authorized Distributors. Refer to Truth s Terms & Conditions for further details. LOGO OPTIONS: For that personalized touch, Truth s 9400 Series Sash Locks are capable of accepting your companyís name or logo. Truth s logo reproduction processes is an attractive way of highlighting your company signature. MATERIAL: High-pressure, corrosion resistant, die-cast zinc. FINISH: Electrostatically applied, durable coatings that provide excellent resistance to chipping, scratching and corrosion while maintaining color stability for years in direct sunlight. Please refer to Truth s Color Chart for examples of Truth s most popular finish options. Truth also offers a wide range of decorative plated finishes contact Truth for additional information on availability of these finishes on specific product lines. ORDERING INFORMATION: 1. Identify the style of base desired (specify by part number). 2. Identify the style of cam desired. Note these cams are handed (specify by part number). 3. Order the 9400 Series assembled base unit that has this configuration. Truth Hardware Sales Team can help you identify this part number. 4. Order the 9400 Series style of keeper desired (specify by part number). 5. Specify finish choice. Types of screws required determined by material of profile used (sold separately). For additional information on screw selection see Truth Tips. TRUTH TIPS: 1. A lock with pick-resistant alignment lugs should be used whenever possible. A lock without lugs should be chosen when the lugs cause interference with divided light grills or other window features. 2. When two locks are used on one window, the placement of each lock, with respect to its keeper, becomes very critical to maintain a constant weatherseal on all sides of the window and to insure that each lock engages properly with its keeper. 3. For accurate hardware placement in vinyl or metal applications, pre-drilling of the window profile is recommended. 4. For vinyl window applications, mounting screws should pass through two PVC walls, or one PVC wall and one insert wall. For this reason, it may be necessary to use a longer screw than is recommended. 5. For metal window profiles, Truth recommends stainless steel machine screws. However, in most applications, stainless steel sheet metal screws will provide adequate holding power. INCLUDE TRUTH SPECS ON YOUR NET WINDOW PROJECT Window check rail locks shall be included which will increase both security and weather seal tightness. The lock must provide easy operation and positive locked feel. Window check rail locks will be of internal cam design to provide optimum sealing of the meeting rails. The lock and accompanying keeper will prevent misalignment during locking. The lock and keeper shall be constructed of high pressure zinc alloy die castings. Window locks shall be 9400 Series Sash Locks as manufactured by Truth Hardware. 6

9400 SASH LOCK & KEEPERS FIG. 1 SASH LOCK AND KEEPER.437 [11.1 mm] 2.062 [52.4 mm] 1.120 [28.4 mm] NIBS NESTING NIBS 1.700 [43.2 mm] RIGHT HAND SHOWN.820 [20.8 mm] 2.578 [65.5 mm] CAM PULL-IN.060 HANDING NIBS PART NUMBER A09400400 A09400401 A09400444 RH LH NO NIBS NIBS NESTING NIBS WOOD: (QTY 2) (P/N 19050) #6.750 PHILLIPS FLAT HEAD SHEET METAL SCREWS PVC/METAL: (QTY 2) #6 PHILLIPS FLAT HEAD SCREW (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) FIG. 2 C09405. KEEPER 2.062 [52.4 mm].310 [7.9 mm].155 [3.9 mm].505 [12.8 mm] 2.578 [65.5 mm] WOOD: (QTY 2) (P/N 19050) #6.750 PHILLIPS FLAT HEAD SHEET METAL SCREWS PVC/METAL: (QTY 2) #6 PHILLIPS FLAT HEAD SCREW (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) AVAILABLE LOCKS A09400400 6a

9400 SASH LOCK & KEEPERS FIG. 3 C09603. KEEPER 2.062 [52.4 mm].310 [7.9 mm].155 [3.9 mm].505 [12.8 mm] WOOD: (QTY 2) (P/N 19050) #6.750 PHILLIPS FLAT HEAD SHEET METAL SCREWS PVC/METAL: (QTY 2) #6 PHILLIPS FLAT HEAD SCREW (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 2.578 [65.5 mm] AVAILABLE LOCKS A09400401 FIG. 4 C30063. KEEPER 2.126 [54.0 mm].312 [7.9 mm].156 [4.0 mm].375 [9.5 mm] 2.840 [72.1 mm].575 [14.6 mm].755 [19.2 mm] WOOD: (QTY 2) (P/N 19050) #6.750 PHILLIPS FLAT HEAD SHEET METAL SCREWS PVC/METAL: (QTY 2) #6 PHILLIPS FLAT HEAD SCREW (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) AVAILABLE LOCKS A09400444 FIG. 5 41404 KEEPER 2.125 [54.0 mm].223 [5.7 mm] (QTY 2)#6 SHEET METAL SCREWS WITH #5 HEAD, PHIILIPS FLAT HEAD SCREWS. (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 2.578 [65.5 mm].226 [5.8 mm].505 [12.8 mm].350 [8.9 mm] 6b

9400 SASH LOCK & KEEPERS 6c 700 WEST BRIDGE STREET, OWATONNA, MN 55060 n 507.451.5620 800.866.7884 n TRUTH.COM

DOUBLE HUNG SLIDER 17 ENTRYGARD II CAM LOCK Designed for use on slider and single/double-hung windows, the EntryGard and EntryGard II Cam Lock s concealed locking mechanisms help protect moving parts from dust and dirt for added lock life while producing a better seal of the sash at the head and sill. The internal cam eliminates paint abrasions and produces a.125 (3.2 mm) pull-in with a.156 (4.0 mm) lifting ability. Air infiltration has been substantially reduced by pulling the meeting rails tightly together. ENTRYGARD II The EntryGard II Check Rail Lock features a sleek and stylish new handle design, and has been designed such that the lock s back plate could be eliminated without compromising the strength or performance of this product. An improved detent in the handle motion of the EntryGard II, assures the user that the cam is either fully open or closed. ENTRYGARD SNAP-BACK LOCK This double hung/slider lock has the ability to retract the cam when the handle motion is within approximately 30 degrees of the open position. The spring action of the handle and the cam will eliminate exposing the cam when in the partially open position, thus avoiding interference with divided light grilles and/or crashing on the top rail. These locks are available with or without alignment lugs. These lugs have been designed to help prevent shifting of the rails during locking for an enhanced window seal. Spring action holds handle in locked or unlocked position to prevent damage to windows. SECURITY & RELIABILITY: The pick-resistant design of this lock helps you exceed the load requirements for AAMA 1302.5 Forced Entry Resistance Test, the California Model Building Security Ordinance and ASTM-588 Forced Entry Test. Additional Keepers for special profile applications are also available - refer to EntryGard Keeper page for further information. WARRANTY: Protected under the terms of the Truth Warranty for Window & Door Manufacturers & Authorized Distributors. Refer to Truth s Terms & Conditions for further details. LOGO OPTIONS: For that personalized touch, Truth s EntryGard Check Rail Locks are capable of accepting your company s name or logo. Truth s unique custom print logo reproduction processes is an attractive way of highlighting your company signature. For further details on where your company s logo would appear, please refer to the following drawings. MATERIAL: High-pressure, corrosion resistant, die-cast zinc. FINISH: Electrostatically applied, durable coatings that provide excellent resistance to chipping, scratching and corrosion while maintaining color stability for years in direct sunlight. Please refer to Truth s Color Chart for examples of Truth s most popular finish options. Truth also offers a wide range of decorative plated finishes contact Truth for additional information on availability of these finishes on specific product lines. ORDERING INFORMATION: 1. Choose cam lock style desired (see table below). 2. Specify finish number. 3. Select mounting hardware required (sold separately): For Keeper styles - see EntryGard Keeper section. Types of screws required determined by material of profile used. Refer to drawings for complete information on screw type and quantity needed (sold separately). For additional information regarding screw selection, refer to EntryGard Keeper catalog page for styles and part numbers. TRUTH TIPS: 1. A lock with pick-resistant alignment lugs should be used whenever possible. A lock without lugs should be chosen when the lugs cause interference with divided light grills or other window features. 2. When two locks are used on one window, the placement of each lock, with respect to its keeper, becomes very critical to maintain a constant weatherseal on all sides of the window and to insure that each lock engages properly with its keeper. 3. For accurate hardware placement in vinyl or metal applications, pre-drilling of the window profile is recommended. 4. For vinyl window applications, mounting screws should pass through two PVC walls, or one PVC wall and one insert wall. For this reason, it may be necessary to use a longer screw than is recommended. 5. For metal window profiles, Truth recommends stainless steel machine screws. However, in most applications, stainless steel sheet metal screws will provide adequate holding power. INCLUDE TRUTH SPECS ON YOUR NET WINDOW PROJECT Window check rail locks shall be included which will increase both security and weather seal tightness. The lock must provide easy operation and positive locked feel (detent). Window check rail locks will be of internal cam design to provide.125 (3.2 mm) of pull-in to aid in sealing the meeting rails. The lock and accompanying keeper will prevent misalignment during locking. The lock and keeper shall be constructed of high pressure zinc alloy die castings. Window locks shall be 17 series EntryGard as manufactured by Truth 7

17 ENTRYGARD II CAM LOCK FIG. 1 APPLICATION OF TRUTH ENTRYGARD AND ENTRYGARD II CHECK RAIL LOCK 2.061 [52.3 mm] A 1.125 [28.6 mm] SURFACE MOUNTED KEEPER 1.624 [41.3 mm] 2.593 [65.9 mm] D GLASS.844 [21.4 mm] FACE MOUNTED KEEPER.500 [12.7 mm] CHECKRAIL TOP AREA FRONT AREA "CUSTOME PRINT" LOGO AREAS AVAILABLE (FULL SCALE) WOOD: (QTY 2) (P/N 19050) #7.750 PHILLIPS, FLAT HEAD, SHEET METAL SCREWS. PVC/METAL: (QTY 2) #7 PHILLIPS, FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) FIG. 2 ENTRYGARD AND ENTRYGARD II CHECK RAIL LOCKS B ALIGNMENT LUGS CAM C NOTE: ALL LOCKS HAVE.125 PULL-IN. PRODUCT NUMBER B C WITH LUGS WITHOUT LUGS TYPE 17.67 EG II 17.68 EG II 17.70 EG 17.74.438 (11.1mm) 2.062 (52.4mm) EG 17.19 EG 17.23 EG 17.30.688 (17.5mm) 1.875 (47.6mm) EG 17.31.688 (17.5mm) 1.875 (47.6mm) EG 17.92.688 (17.5mm) 1.875 (47.6mm) EG II SPECIAL FEATURES SNAP BACK LOCK SNAP BACK LOCK 7a 700 WEST BRIDGE STREET, OWATONNA, MN 55060 n 507.451.5620 800.866.7884 n TRUTH.COM

DOUBLE HUNG SLIDER 17 ENTRYGARD CAM LOCK KEEPERS There is a wide variety of profiles in the marketplace today, and with each of these, there is the potential for a unique mounting application. No one Keeper will work in every situation and because of this, Truth has developed a wide variety of shapes and styles to help meet these needs. The Keepers in the accompanying drawings represent all of the Keepers that Truth has developed for use with the EntryGard Cam Locks. These drawings should provide you with all the technical information you may require. However, if you wish further technical assistance in selecting a Keeper, please contact Truth. WARRANTY: Protected under the terms of the Truth Warranty for Window & Door Manufacturers & Authorized Distributors. Refer to Truth s Terms & Conditions for further details. TRUTH TIPS: 1. For accurate hardware placement in vinyl or metal applications, pre-drilling of the window profile is recommended. 2. For vinyl window applications, mounting screws should pass through two PVC walls, or one PVC wall and one insert wall. For this reason, it may be necessary to use a longer screw than is recommended. 3. For metal window profiles, Truth recommends stainless steel machine screws. However, in most applications, stainless steel sheet metal screws will provide adequate holding power. MATERIAL: High-pressure, corrosion resistant, die-cast zinc. FINISH: Electrostatically applied, durable coatings that provide excellent resistance to chipping, scratching and corrosion while maintaining color stability for years in direct sunlight. Please refer to Truth s Color Chart for examples of Truth s most popular finish options. Truth also offers a wide range of decorative plated finishes contact Truth for additional information on availability of these finishes on specific product lines. Types of screws required determined by material of profile used. Refer to drawings for complete information on screw type and quantity needed (sold separately). For additional information regarding screw selection - see Truth Tips. ORDERING INFORMATION: 1. Order Keepers by part number. Refer to lock section for details on A and D dimensions. 2. Specify finish number. 8

17 ENTRYGARD CAM LOCK KEEPERS FIG. 1 40670. KEEPER (face mounted).156 [4.0 mm] 1.749 [44.4 mm] 1.318 [33.5 mm] NOTE: CAM MAY INTERFERE WITH GLASS.312 [7.9 mm] D AVAILABLE LOCKS D WOOD: (QTY 2) (P/N 19050) #6.750 PHILLIPS,FLAT HEAD SHEET METAL SCREWS PVC/METAL: (QTY 2) #6 PHILLIPS, FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE).876 [22.3 mm].080 [2.0 mm] 17.23 17.31 17.66.348 (8.8mm) 17.67 17.70 FIG. 2 40375. KEEPER (face mounted) NOTE: CAM MAY INTERFERE WITH GLASS.182 [4.6 mm] 1.037 [26.4 mm] 1.510 [38.4 mm].170 [4.3 mm] D WOOD: (QTY 2) #10.750 PHILLIPS, PAN HEAD SHEET METAL SCREWS PVC/METAL: (QTY 2) #10 PHILLIPS, PAN HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE).453 [11.5 mm].436 [11.1 mm] AVAILABLE LOCKS ALL ENTRYGARD LOCKS.100 [2.5 mm] D.864 (21.9mm) FIG. 3 41298. KEEPER (face mounted) NOTE:.500 [12.7 mm].182 [4.6 mm] CAM MAY INTERFERE WITH GLASS D E.170 [4.3 mm] 1.770 [45.0 mm] 8a WOOD: (QTY 2) (P/N 19050) #6.750 PHILLIPS,FLAT HEAD SHEET METAL SCREWS PVC/METAL: (QTY 2) #6 PHILLIPS, FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 1.000 [25.4 mm] AVAILABLE LOCKS ALL ENTRYGARD LOCKS D.864 (21.9mm).090 [2.3 mm] E.562 (14.3mm)

17 ENTRYGARD CAM LOCK KEEPERS FIG. 4 40715. KEEPER (wide base and slant top).250 [6.4 mm] 2.062 [52.4 mm].438 [11.1 mm] WOOD: (QTY 2) (P/N 19100) #7.750 PHILLIPS,FLAT HEAD SHEET METAL SCREWS.536 [13.6 mm] 2.578 [65.5 mm] AVAILABLE LOCKS 17.19.704 (17.9mm) 17.30.954 (24.2mm) 17.68.704 (17.9mm) A PVC/METAL: (QTY 2) #7 PHILLIPS, FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 17.69.704 (17.9mm) 17.74.704 (17.9mm) FIG. 5 45070. KEEPER (flat base, beveled edge, slotted holes).270 [6.9 mm] 2.060 [52.3 mm].135 [3.4 mm].538 [13.7 mm] WOOD: (QTY 2) (P/N 19100) #7.750 PHILLIPS,FLAT HEAD SHEET METAL SCREWS PVC/METAL: (QTY 2) #7 PHILLIPS, FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 2.594 [65.9 mm] AVAILABLE LOCKS A 17.19.704 (17.9mm) 17.30.954 (24.2mm) 17.68.704 (17.9mm) 17.69.704 (17.9mm) 17.74.704 (17.9mm) FIG. 6 45131. KEEPER (narrow flat base).312 [7.9 mm] 2.060 [52.3 mm].156 [4.0 mm].536 [13.6 mm] WOOD: (QTY 2) (P/N 19050) #6.750 PHILLIPS,FLAT HEAD SHEET METAL SCREWS 2.590 [65.8 mm] AVAILABLE LOCKS A 17.19.704 (17.9mm) 17.30.954 (24.2mm) 17.68.704 (17.9mm) PVC/METAL: (QTY 2) #6 PHILLIPS, FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 17.69.704 (17.9mm) 17.74.704 (17.9mm) 8b

17 ENTRYGARD CAM LOCK KEEPERS FIG. 7 40320. KEEPER (notched narrow base).311 [7.9 mm] 2.062 [52.4 mm].156 [4.0 mm].531 [13.5 mm] 2.594 [65.9 mm] WOOD: (QTY 2) (P/N 19050) #6.750 PHILLIPS,FLAT HEAD SHEET METAL SCREWS PVC/METAL: (QTY 2) #6 PHILLIPS, FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) AVAILABLE LOCKS 17.19 A.610 (15.5mm) 17.30.860 (21.8mm) 17.68.610 (15.5mm) 17.74.610 (15.5mm) FIG. 8 40367. KEEPER (without alignment lug slots).440 [11.2 mm] 2.061 [52.3 mm].250 [6.4 mm].530 [13.5 mm] 2.590 [65.8 mm] WOOD: (QTY 2) (P/N 19050) #7.750 PHILLIPS,FLAT HEAD SHEET METAL SCREWS PVC/METAL: (QTY 2) #7 PHILLIPS, FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) AVAILABLE LOCKS 17.23 17.31 17.66 17.67 17.70 A.704 (17.9mm).954 (24.2mm).704 (17.9mm).704 (17.9mm).704 (17.9mm) 8c 700 WEST BRIDGE STREET, OWATONNA, MN 55060 n 507.451.5620 800.866.7884 n TRUTH.COM

DOUBLE HUNG SLIDER 17.04 SASH LOCK Modeled after Truth s popular 9400 and EntryGard Series sash locks, the 17.04 Series Lock is an excellent option for either single or double-hung style windows. Designed with a slightly different mounting hole pattern than its predecessors, the 17.04 is designed easily adaptable to most window profiles in the market today. Concealed locking mechanisms help protect moving parts from dust and dirt for added lock life while producing a better seal of the sash at the head and sill. The internal cam eliminates unsightly paint abrasions caused by the interaction of cam and keeper. These locks are available with or without alignment lugs. These lugs have been designed to help prevent shifting of the rails during locking for an enhanced window seal. Tapered nesting lugs, which help guide the lock to the keeper are also an option. WARRANTY: Protected under the terms of the "Truth Warranty for Window & Door Manufacturers & Authorized Distributors". Refer to Truth s Terms & Conditions for further details. LOGO OPTIONS: For that "personalized touch", Truth s 17.04 Series Sash Locks are capable of accepting your company s name or logo. Truth s logo reproduction processes is an attractive way of highlighting your company signature. MATERIAL: High-pressure, corrosion resistant, die-cast zinc. FINISH: Electrostatically applied, durable coatings that provide excellent resistance to chipping, scratching and corrosion while maintaining color stability for years in direct sunlight. Please refer to Truth s Color Chart for examples of Truth s most popular finish options. Truth also offers a wide range of decorative plated finishes contact Truth for additional information on availability of these finishes on specific product lines. ORDERING INFORMATION: 1. Order a 17.04 Series Lock. 2. Order the 17.04 Series style of keeper desired (specify by part number). 3.Specify finish choice. Types of screws required determined by material of profile used (sold separately). For additional information on screw selection see Truth Tips. TRUTH TIPS: 1. A lock with pick-resistant alignment lugs should be used whenever possible. A lock without lugs should be chosen when the lugs cause interference with divided light grills or other window features. 2. When two locks are used on one window, the placement of each lock, with respect to its keeper, becomes very critical to maintain a constant weatherseal on all sides of the window and to insure that each lock engages properly with its keeper. 3. For accurate hardware placement in vinyl or metal applications, pre-drilling of the window profile is recommended. 4. For vinyl window applications, mounting screws should pass through two PVC walls, or one PVC wall and one insert wall. For this reason, it may be necessary to use a longer screw than is recommended. 5. For metal window profiles, Truth recommends stainless steel machine screws. However, in most applications, stainless steel sheet metal screws will provide adequate holding power. INCLUDE TRUTH SPECS IN YOUR NET WINDOW PROJECT Window check rail locks shall be included which will increase both security and weather seal tightness. The lock must provide easy operation and positive locked feel. Window check rail locks will be of internal cam design to provide optimum sealing of the meeting rails. The lock and accompanying keeper will prevent misalignment during locking. The lock and keeper shall be constructed of high pressure zinc alloy die castings. Window locks shall be 17.04 Series Sash Locks as manufactured by Truth Hardware. 9

17.04 SASH LOCK 9a

17.04 SASH LOCK 9b

17.04 SASH LOCK 9c 700 west bridge street, owatonna, mn 55060 n 507.451.5620 800.866.7884 n TRUTH.COM

DOUBLE HUNG SLIDER 9900 SASH LOCK Truth Hardware s stealth lock has its housing hidden inside the sash for the ultimate in low profile locking systems. The fasteners are installed from the front face of the locks base and keeper, thereby eliminating everything except the handle from view. Totally concealed locking mechanism helps protect moving parts from dust and dirt from accumulating. WARRANTY: Protected under the terms of the Truth Warranty for Window & Door Manufacturers & Authorized Distributors. Refer to Truth s Terms & Conditions for further details. FINISH: Electrostatically applied, durable coatings that provide excellent resistance to chipping, scratching and corrosion while maintaining color stability for years in direct sunlight. Please refer to Truth s Color Chart for examples of Truth s most popular finish options. Truth also offers a wide range of decorative plated finishes contact Truth for additional information on availability of these finishes on specific product lines. MATERIAL: High pressure, corrosion-resistant, die-cast zinc. Refer to drawings for complete information on screw type and quantity needed (sold separately). ORDERING INFORMATION: 1. Order 9900 Series Sash Lock 2. Select keeper style needed (order by item number) 3. Specify finish choice. INCLUDE TRUTH SPECS ON YOUR NET WINDOW PROJECT Window check rail locks shall be included which will increase both security and weather seal tightness. The lock must provide easy operation and positive locked feel, while being low in profile to improve the windows appearance. Window check rail locks will be of internal cam design to provide optimum pull-in to aid in sealing the meeting rails. The lock and keeper shall be constructed of high pressure zinc alloy die castings. Window locks shall be 9900 Series Sash Lock as manufactured by Truth Hardware. TRUTH TIPS: 1. When two locks are used on one window, the placement of each lock, with respect to its keeper, becomes very critical to maintain a constant weatherseal on all sides of the window and to insure that each lock engages properly with its keeper. 10

9900 SASH LOCK 10a

9900 SASH LOCK 10b

9900 SASH LOCK FIG. 5 9391 KEEPER 2.800.320 [71.1 mm] [8.1 mm] (QTY 2) #6 PHILLIPS FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE.185 [4.7 mm] 2.062 [52.4 mm].370 [9.4 mm] AVAILABLE LOCKS A09900402 A09900404 A09900408 FIG. 6 9703 KEEPER.320 [8.1 mm] 3.180 [80.8 mm] (QTY 2) #6 PHILLIPS FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE.556.185 [14.1 mm] [4.7 mm] 2.062 [52.4 mm] AVAILABLE LOCKS A09900402 A09900404 A09900408 FIG. 7 9906 KEEPER.322 [8.2 mm] 2.750 [69.8 mm].185 [4.7 mm].370 [9.4 mm] (QTY 2) #6 PHILLIPS FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE 5 2.052 [52.1 mm] AVAILABLE LOCKS A09900402 A09900404 A09900408 FIG. 8 43039 KEEPER 2.749 [69.8 mm].155 [3.9 mm] A09930402 LOCK ASSEMBLY (QTY 2) #6 SHEET METAL SCREWS PHILLIPS FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE.396 [10.1 mm] 1.750 [44.4 mm].164 [4.2 mm] 1.249 [31.7 mm].080 [2.0 mm] AVAILABLE LOCKS A09900402 A09900404 A09900408 10c 700 WEST BRIDGE STREET, OWATONNA, MN 55060 n 507.451.5620 800.866.7884 n TRUTH.COM

DOUBLE HUNG SLIDER 9950 LOCK WITH CONCEALED KEEPER Engineered with a fresh new style and a streamline design that conceals the keeper under the housing, Truth s 9950 Series Lock and Keepers are a unique way to accent your window. WARRANTY: Protected under the terms of the Truth Warranty for Window & Door Manufacturers & Authorized Distributors. Refer to Truth s Terms & Conditions for further details. MATERIAL: High-pressure, corrosion-resistant, die-cast zinc. FINISH: Electrostatically applied, durable coatings that provide excellent resistance to chipping, scratching and corrosion while maintaining color stability for years in direct sunlight. Please refer to Truth s Color Chart for examples of Truth s most popular finish options. Contact Truth for additional information on availability of these finishes on specific product lines. ORDERING INFORMATION: 1. Choose the 9950 series lock required. See drawings for available options. 2. Order the 9954 series keeper. 3. Specify finish choice. Types of screws required determined by material of profile used. Refer to drawings for complete information on screw type and quantity needed (sold separately). For additional information on screw selection - see Truth Tips. TRUTH TIPS: 1. When two locks are used on one window, the placement of each lock, with respect to its keeper, becomes very critical to maintain a constant weatherseal on all sides of the window and to insure that each lock engages properly with its keeper. 2. For accurate hardware placement in vinyl or metal applications, pre-drilling of the window profile is recommended. 3. For vinyl window applications, mounting screws should pass through two PVC walls, or one PVC wall and one insert wall. For this reason, it may be necessary to use a longer screw than is recommended. 4. For metal window profiles, Truth recommends stainless steel machine screws. However, in most applications, stainless steel sheet metal screws will provide adequate holding power. INCLUDE TRUTH SPECS ON YOUR NET WINDOW PROJECT Window check rail locks shall be included which will increase both security and weather seal tightness. The lock must provide easy operation and positive locked feel. The keeper should be concealed under the housing of the lock. Window check rail locks will be of internal cam design to provide optimum pull-in to aid in sealing the meeting rails. The lock and accompanying keeper will prevent mis-alignment during locking. The lock and keeper shall be constructed of high pressure zinc alloy die castings. Window locks shall be 9950 Series locks as manufactured by Truth Hardware. 11

9950 LOCK WITH CONCEALED KEEPER FIG. 1 A09950400 SASH LOCK.640 [16.3 mm] 2.250 [57.2 mm] 1.656 [42.1 mm] LOGO AREA LOGO AREA SHOWN FULL SCALE 1.257 [31.9 mm] LOGO AREA.432 [11.0 mm] AVAILABLE LOGO AREA.674 [17.1 mm] RECOMMENDED SCREW: (QTY 2) #6 PHILLIPS FLAT HEAD SCREW (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 2.812 [71.4 mm] FIG. 2 A09950401 SASH LOCK 1.257 [31.9 mm].850 [21.6 mm] 2.250 [57.2 mm] LOGO AREA 1.656 [42.1 mm] LOGO AREA LOGO AREA SHOWN FULL SCALE.432 [11.0 mm] AVAILABLE LOGO AREA.674 [17.1 mm] RECOMMENDED SCREW: (QTY 2) #6 PHILLIPS FLAT HEAD SCREW (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 2.812 [71.4 mm] FIG. 3 C09954 CONCELED KEEPER 2.250 [57.2 mm].280 [7.1 mm].140 [3.6 mm].340 [8.6 mm] RECOMMENDED SCREW: (QTY 2) #6 SCREW WITH A #5 HEAD (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 2.818 [71.6 mm] 11a 700 WEST BRIDGE STREET, OWATONNA, MN 55060 507.451.5620 800.866.7884 TRUTH.COM

DOUBLE HUNG SLIDER 30590 CAM GARD LOCK Stylish new design to the housing has made this lock a popular upgrade from those using the 7538 Series Sash Locks. As with its predecessor, the 30590 still has the following features which made it one of the industry s best: Streamlined low profile handle folds snugly against the housing producing a clean appearance, and helps to eliminate interference in shipping. One-piece box construction spring provides a strong detent in handle movement, thus assuring the homeowner that the handle has completed its travel. Available in either left- or right-hand, Truth s Cam Gard Lock is built with a base plate to help improve its forced entry resistance (FER). 30590 latches are designed to be compatible with specific keepers that will help produce the optimum engagement between lock and keeper. WARRANTY: Protected under the terms of the Truth Warranty for Window & Door Manufacturers & Authorized Distributors. Refer to Truth s Terms & Conditions for further details. MATERIAL: High-pressure, corrosion-resistant, die-cast zinc. FINISH: Electrostatically applied, durable coatings that provide excellent resistance to chipping, scratching and corrosion while maintaining color stability for years in direct sunlight. Please refer to Truth s Color Chart for examples of Truth s most popular finish options. Truth also offers a wide range of decorative plated finishes contact Truth for additional information on availability of these finishes on specific product lines. ORDERING INFORMATION: 1. Refer to the following drawing for item number information for the Cam Gard Lock you require. (Note: these locks are handed ) 2. Order the keeper style required. 3. Specify finish choice. Types of screws required determined by material of profile used (sold separately). For additional information on screw selection - see Truth Tips. TRUTH TIPS: 1. When two locks are used on one window, the placement of each lock, with respect to its keeper, becomes very critical to maintain a constant weatherseal on all sides of the window and to insure that each lock engages properly with its keeper. 2. For accurate hardware placement in vinyl or metal applications, pre-drilling of the window profile is recommended. 3. For vinyl window applications, mounting screws should pass through two PVC walls, or one PVC wall and one insert wall. For this reason, it may be necessary to use a longer screw than is recommended. 4. For metal window profiles, Truth recommends stainless steel machine screws. However, in most applications, stainless steel sheet metal screws will provide adequate holding power. INCLUDE TRUTH SPECS ON YOUR NET WINDOW PROJECT Window check rail locks shall be included which will increase both security and weather seal tightness. The lock must provide easy operation and a positive locked feel. The lock and keeper shall be constructed of high pressure zinc alloy die castings. Window locks shall be 30590 Cam Gard Series as manufactured by Truth Hardware. 12

30590 CAM GARD LOCK FIG. 1 A30590402 LOCK 2.250 [57.2 mm].780 [19.8 mm] 1.268 [32.2 mm] RIGHT HAND LEFT HAND A30590402 A30590403.280 [7.1 mm] LEFT HAND SHOWN.650 [16.5 mm] CAM PULL-IN.080 (QTY 2) #6 PHILLIPS FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 3.250 [82.6 mm].480 [12.2 mm] AVAILABLE KEEPERS C30628 C30643 A 0.56 0.617 B 0.04 0.04 C 0.5 FIG. 2 C30628. KEEPER 2.240 [56.9 mm].260 [6.6 mm].130 [3.3 mm] FIG. 3 C30643. KEEPER.375 2.240 [9.5 mm] [56.9 mm].188 [4.8 mm].530 [13.5 mm].530 [13.5 mm] 2.875 [73.0 mm] AVAILABLE LOCKS 2.875 [73.0 mm] AVAILABLE LOCKS (QTY 2) #6 WITH A #5 HEAD PHILLIPS FLAT HEAD SCREW (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) A30590402 A30590403 (QTY 2) #6 PHILLIPS FLAT HEAD SCREW (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) A30590402 A30590403 12a 700 WEST BRIDGE STREET, OWATONNA, MN 55060 n 507.451.5620 800.866.7884 n TRUTH.COM

DOUBLE HUNG SLIDER 17 RESTORATION HARDWARE When the window s design or the home s décor calls for that traditional touch, Truth s Restoration Hardware is the answer. Designed and crafted to replicate the styling of window hardware from an earlier era, Truth has used today s technology to create a hardware system that is both stylish and functional. APPLICATION AND DESIGN: Truth s Restoration Lock comes equipped with the traditional open cam look, and is fitted with a durable plastic insert on the keeper to protect the surface of the cam during lock-up and to aid in its smooth operation. This open cam design also provides for a simple visual indicator that the system is locked. The traditional styling of the thumb lever on the lock is ergonomically simple to operate. The spring back design snaps the cam into the lock or un-locked position which reduces the potential for accidental marring of grilles. With a lower profile than many other lock and keeper configurations, Truth s Restoration Lock system helps to minimize sight line interference. Utilizing standard mounting holes (2-1/16") and setback (11/16") this lock and keeper are an easy retrofit to existing lock applications thereby reducing any additional manufacturing set-ups. Truth also offers a Restoration Sash Lift which has a traditional finger-pull look, and encourages the lifting of the window from bottom thereby putting less stress on the sash than would occur from pushing on the top rail. See Truth s Sash Lift section for further technical information. WARRANTY: Protected under the terms of the Truth Warranty for Window & Door Manufacturers & Authorized Distributors. Refer to Truth s Terms & Conditions for further details. MATERIAL: High-pressure, corrosion-resistant die-cast zinc. Molded plastic insert. FINISH: Electrostatically applied, durable coatings that provide excellent resistance to chipping, scratching and corrosion while maintaining color stability for years in direct sunlight. Please refer to Truth s Color Chart for examples of Truth s most popular finish options. Truth also offers a wide range of decorative plated finishes contact Truth for additional information on availability of these finishes on specific product lines. ORDERING INFORMATION: 1. Order item #17.02 Restoration Lock. 2. Order item #12505. Restoration Keeper 3. Order item #18.16 Restoration Lift 4. Specify finish 5. Select screws (fasteners). Sold separately. Phillips flat head screws. Refer to drawings for additional specs. Length and thread type to be determined by profile. For further information on screw selection see Truth Tips TRUTH TIPS: 1. When two locks are used on one window, the placement of each lock, with respect to its keeper becomes very critical to maintain a constant weather seal on all sides of the window and to insure that each lock engages properly with its keeper. 2. For accurate hardware placement in vinyl or metal applications, pre-drilling of the window profile is recommended. 3. For vinyl window applications, mounting screws should pass through two PVC walls, or one PVC wall and one insert wall. For this reason, it may be necessary to use a longer screw than is recommended. INCLUDE TRUTH SPECS ON YOUR NET WINDOW PROJECT Window check rail locks shall be included which increase both security and weather seal tightness. The lock must provide easy operation and positive locked feel (detent). Window check rail locks shall be of open cam design. Locks will be of #17 Series design as manufactured by Truth Hardware. 13

17 RESTORATION HARDWARE 13a 700 west bridge street, owatonna, mn 55060 n 507.451.5620 800.866.7884 n TRUTH.COM

DOUBLE HUNG SLIDER 19 POSITIVE ACTION LOCK (PAL SYSTEM) Truth Hardware s Positive Action Lock (PAL) Systems are some of the most versatile and easy to operate locking systems in the marketplace today. Available in the original Push Button design and new Slide Tab designs, these lock systems are simple to operate and provide added security for both vinyl or wood windows. A simple movement of the locking tab or push of the button disengages the lock allowing the sash to move freely. When the window is closed the PAL System automatically locks, securing the window without having to manipulate the lock again. Certain models can be used with or without a keeper depending on the window s design. Window profiles that incorporate a notch in the meeting rail may not require a keeper to secure the window in the locked position resulting in decreased inventory costs to the manufacturer and infinite side-to-side forgiveness in the locks application. FEATURES & BENEFITS: Snap-on Cover: Available in the 19.62/63 slide tab designs, this feature allows for more aesthetic cover possibilities thus reducing material costs and allowing it to fit more applications. Easy Operation: Comfortable finger pull (slide tab design) provides positive feedback that the lock is fully retracted (slight snap felt). Text is located under the pull on the lock to indicated an un-locked condition when the lock bolt is retracted. This provides at-aglance feedback to the homeowner that the lock is in the unlocked state. Multiple Mounting Options: Slide Tab design can be mounted with screw fasteners in both the vertical (recessed or top mount) and horizontal (recessed only) orientations and may be fitted into Truth s standard 9369 Series Recessed Lock cut-out (call Truth for info). Visual Security: The Truth lock bolt on the PAL System will stay retracted when opening the sash and remain retracted until triggered in a positively locked position. Competitive locks tend to trigger when opening the sash, thus providing a false locked position. This unique feature helps users of the PAL System to prevent accidental marring of their window as the lock slides past decorative grilles. Multiple Keeper configurations: Including top-mount, and face mount keepers. Custom keepers also available to meet customer specific application needs. LOGO OPTIONS: For that personalized touch, Truth Hardware s Positive Action Locks are capable of accepting your company s name or logo with Truth s pad printing process. This logo reproduction process is an attractive way of highlighting your company signature. WARRANTY: Protected under the terms of the Truth Warranty for Window & Door Manufacturers and Authorized Distributors. Refer to Truth s Terms & Conditions for further details. MATERIAL: High pressure, corrosion resistant, diecast zinc with a high strength acetal bolt. Slide Tab version constructed of high quality molded plastic cover over die cast base. FINISH: Electrostatically applied, durable coatings that provide excellent resistance to chipping, scratching and corrosion while maintaining color stability for years in direct sunlight. Please refer to Truth s color chart for examples of Truth s most popular finish options. Truth also offers a wide range of decorative plated finishes contact Truth for additional information on availability of these finishes on specific product lines. ORDERING INFORMATION: 1. Order PAL System style (specify by part number) #19.62.00.002 Slide Tab PAL Hook Version w/screw hole spread 1.812 and 1.312 #19.63.00.001 Slide Tab PAL Hook Version w/screw hole spread 2.062 #19.64..100 Slide Tab PAL 2. Order covers for 19.62/63 Slide Tab Versions separately #13663. Cover (19.62 model) #13885. Cover (19.63 model) 3. Specify finish number. 4. Select screws (fasteners). Sold separately. 2 - #7 Phillips Flat Head Screws. Refer to drawings for additional specs. Length and thread type to be determined by profile. For further information on screw selection see Truth Tips. 19.60 Series 19.63 Series 19.62 Series 19.64 Series TRUTH TIPS: 1. For accurate hardware placement in vinyl applications, pre-drilling of the window profile is strongly recommended. 2. To help locate mounting position, Truth recommends a locating groove in the profile. The dimpled version of the PAL System used on profiles with a groove will also help keep lock in position during application process. 3. For vinyl window applications, mounting screws should pass through two PVC walls, or one PVC wall and one insert wall. For this reason, it may be necessary to use a longer screw than is recommended. 4. For top mounted keeper configurations a 0.3 minimum deep surface is needed on the fixed rail with both surfaces flush when closed. INCLUDE TRUTH SPECS ON YOUR NET WINDOW PROJECT Window check rail locks shall be included which will increase both security and weather seal tightness. The lock must provide easy operation and positively locks upon closure. Window lock will be of quick snap action swing bolt design providing maximum forgiveness for sash alignment. The product will be constructed of high pressure zinc alloy die cast with high strength acetal bolt. Window lock shall have automatic latching to allow user to use both hands to move the sash. Window will be unlocked by pressing a push lever, or sliding tab. Window locks will be 19 series Positive Action Locks as manufactured by Truth Hardware, Owatonna, Minnesota. 14

19 POSITIVE ACTION LOCK (PAL SYSTEM) FIG. 1 APPLICATION OF 19.64 POSITIVE ACTION LOCK (PAL) SYSTEM 1.681 [17.3 mm].581 [14.7 mm] LOCKED POSITION SHOWN HARDWARE SHOWN 19.64 P.A.L..350 MIN [8.9 mm].220 MA [5.6 mm].190 MIN [4.8 mm] 2.870 [72.9 mm].451 [11.5 mm] 2.250 [57.2 mm].524 [13.3 mm] 1.240 [31.5 mm] LOCKED 1.625 [41.3 mm] UNLOCKED WOOD: *7 PHILLIPS FLAT HEAD SHEET METAL SCREWS (LENGTH TO BE DETERMINED BY PROFILE) PVC/METAL: #7 PHILLIPS FLAT HEAD SCREWS,(LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 1 DIMENSION MUST BE MAINTAINED FOR PROPER LOCK OPERATION **FOR ACCURATE HARDWARE PLACEMENT PRE-DRILLING IS STRONGLY RECOMMENDED 14a

19 POSITIVE ACTION LOCK (PAL SYSTEM) FIG. 2 APPLICATION OF 19.62 POSITIVE ACTION LOCK (PAL) SYSTEM 1.375 [34.9 mm] LOCKED 2.302 [58.5 mm] LOCKED POSITION SHOWN.457 [11.6 mm].688 [17.5 mm] 2.302 [58.5 mm] HARDWARE SHOWN 19.62 P.A.L. 45579. KEEPER 13663. COVER.611 [15.5 mm].861 [21.9 mm] FOR ADDITIONAL KEEPER OPTIONS CONTACT TRUTH ( 1.312 ) [33.3 mm] WOOD: #7 PHILLIPS FLAT HEAD SHEET METAL SCREWS (LENGTH TO BE DETERMINED BY PROFILE) ( 1.812 ) [46.0 mm] PVC/METAL: #7 PHILLIPS FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 14b

19 POSITIVE ACTION LOCK (PAL SYSTEM) FIG. 3 APPLICATION OF 19.63 POSITIVE ACTION LOCK (PAL) SYSTEM 2.813 [71.4 mm] 2.062 [52.4 mm] 1.304 [33.1 mm].935 [23.7 mm] LOCKED LOCKED POSITION SHOWN.738 [18.7 mm].444 [11.3 mm] 2.813 [71.4 mm] HARDWARE SHOWN 19.63 P.A.L. 45639. 13885. KEEPER COVER FOR ADDITIONAL KEEPER OPTIONS CONTACT TRUTH.690 [17.5 mm].940 [23.9 mm] 2.062 [52.4 mm] WOOD: #6 PHILLIPS FLAT HEAD SHEET METAL SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE 14c PVC/METAL: #6 PHILLIPS FLAT HEAD SCREWS, (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE)

19 POSITIVE ACTION LOCK (PAL SYSTEM) FIG. 4 45579. KEEPER 2.062 [52.39 mm].141 [3.6 mm].282 [7.2 mm].405 [10.3 mm] 2.500 [63.5 mm] AVAILABLE LOCK 19.62 PAL 19.63 PAL WOOD: #7 PHILLIPS FLAT HEAD SHEET METAL SCREWS (LENGTH TO BE DETERMINED BY PROFILE) PVC/METAL: #7 PHILLIPS FLAT HEAD SCREWS (LENTGH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 14d

19 POSITIVE ACTION LOCK (PAL SYSTEM) FIG. 5 45639. KEEPER.230 [5.8 mm] 1.020 [25.9 mm].340 [8.6 mm].125 [3.2 mm].288 [7.3 mm].095 [2.4 mm] 1.000 [25.4 mm] 1.700 [43.2 mm] AVAILABLE LOCK 19.62 PAL 19.63 PAL WOOD: #7 PHILLIPS FLAT HEAD SHEET METAL SCREWS (LENGTH TO BE DETERMINED BY PROFILE) PVC/METAL: #7 PHILLIPS FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 14e

19 POSITIVE ACTION LOCK (PAL SYSTEM) FIG. 6 APPLICATION OF 19.60 POSITIVE ACTION LOCK (PAL) SYSTEM.896.836 22.769 mm 21.245 mm 2.062 [52.4 mm].338 [8.6 mm] LOGO AREA 1.145 [29.1 mm] UNLOCKED.090.030 1 2.277 mm.753 mm LOCKED POSITION SHOWN 1.568 [39.8 mm] LOCKED LOGO AREA 2.950 [74.9 mm].665 [16.9 mm].110.045 1 MA. MIN. 2.785 mm 1.134 mm.605 [15.4 mm].390 [9.9 mm] ** PAL SYSTEM USED WITH OUT KEEPER.459 MIN [11.7 mm] PAL SYSTEM USED WITH KEEPER HARDWARE SHOWN 19.60 P.A.L. 41235. KEEPER FOR ADDITIONAL KEEPER OPTIONS CONTACT TRUTH WOOD: (P/N 19160.) #7 1 1/2 PHILLIPS FLAT HEAD SHEET METAL SCREWS. PVC/METAL: #7 PHILLIPS FLAT HEAD SCREWS, (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 1 DIMENSIONS MUST BE MAINTAINED FOR PROPER LOCK OPERATION ** FOR ACCURATE HARDWARE PLACEMENT PRE-DRILLING IS STRONGLY RECOMMENDED 14f

19 POSITIVE ACTION LOCK (PAL SYSTEM) FIG. 7 41235 KEEPER 2.062 [52.4 mm].168 [4.3 mm].338 [8.6 mm].665 [16.9 mm] AVAILABLE LOCK 19.60 PAL 2.950 [74.9 mm] HARDWARE SHOWN 41235. KEEPER WOOD: (QTY 2) (P/N 19160.) #7 1 1/2 PHILLIPS FLAT HEAD SHEET METAL SCREWS PVC/METAL: #7 PHILLIPS FLAT HEAD SCREWS, (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) FIG. 8 32780 KEEPER 2.187 [55.6 mm].125 [3.2 mm].665 [16.9 mm].381 [9.7 mm] (QTY 2) #6 SHEET METAL SCREWS PHIILIPS FLAT HEAD SCREWS. (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) FIG. 9 41320 KEEPER.444 [11.3 mm] 2.950 [74.9 mm] 2.062 [52.4 mm].168 [4.3 mm].250 [6.4 mm].665 [16.9 mm] (QTY 2) #6 SHEET METAL SCREWS PHIILIPS FLAT HEAD SCREWS. (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 2.950 [74.9 mm].338 [8.6 mm] 700 WEST BRIDGE STREET, OWATONNA, MN 55060 507.451.5620 800.866.7884 TRUTH.COM 14g

DOUBLE HUNG SLIDER 19 FuSION SYSTEM Appropriately named the Fusion System, Truth Hardware has successfully merged two separate pieces of window hardware into one completely revolutionary system. Truth has designed a system where the tilt latches are hidden beneath the check rail and are actuated by the same lever as the lock. With just one hand, the homeowner can unlock the window and release the tilt latches. The Fusion system is loaded with features at a very affordable price. TRuTH S FuSION IS ALL AbOuT versatility The Fusion System is designed to give you choices. First, both tilt latches are actuated by a single lock/tilt latch mechanism. This mechanism can be located anywhere on the check rail, so if you prefer to use more than one lock on the rail, you have the option of adding a matching sash lock. With the Fusion system you won t have to stock complete locks in all your different color offerings. There is a standard base assembly that screws into your check rail. Using Truth s patented technology, the stylish housing and lever assembly securely attaches to the base allowing you to efficiently manage your inventory. This fastenerless cover design gives the window a cleaner appearance than other checkrail options and also allows for easy removal of the hardware to make it more convenient to paint or stain the window following its installation. Perhaps the most impressive feature of this system is that it can be used on any-sized window because you cut the connecting strap to its appropriate length after the hardware is installed in the window. What could be easier? FEATuRES & benefits: Available with trigger actuated latches - prevents marring wood when windows are tilted back in. Latches without triggers used primarily in vinyl window applications, are also available. Lock and tilt latch release are actuated by one mechanism - allows you the option of using either single or multiple locks on the window. Pick-resistant base plate increases security. Tilt Latches (Vinyl Application) Latches are hidden into the checkrail - Lets your customer see more of the beauty of your window, rather than the hardware. Totally adjustable to any size window - You cut the connecting strap to the desired length after hardware is installed in the window. Non-handed latches - Less inventory costs and less hassle on the production line. Housing assembly is separate from base - Increases inventory efficiencies by only having to inventory the housing in different colors or finishes - not the entire locking system. Stylish fastenerless housing - Makes it easy to remove for staining or finishing. Easy, intuitive one-handed operation. Corrosion Resistant - Composite construction provides a corrosion resistant system. LOGO OPTIONS: You can personalize the Fusion Lock with your logo. Truth s pad printing Fusion System (locked) Tilt Latches (Wood Application) process is a great way to highlight your company s identity. WARRANTY: Protected under the terms of the Truth Warranty for Window & Door Manufacturers and Authorized Distributors. Refer to Truth s Terms & Conditions for further details. MATERIAL: Housing assembly is powder coated diecast zinc. The lock base and latch assemblies are of a composite construction consisting of engineered plastics, zinc and stainless steel. The latch assembly and lock assembly are tied together by a corrosion resistant strap. FINISH: Electrostatically applied, durable coatings that provide excellent resistance to chipping, scratching and corrosion while maintaining color stability for years in direct sunlight. Please refer to Truth s color chart for examples of Truth s most 15

19 FuSION SYSTEM popular finish options. Truth also offers a wide range of decorative plated finishes - contact Truth for additional information on availability of these finishes on specific product lines. ORDERING INFORMATION: Order the Fusion System by individual components: #19. 70.. 100 - Housing/Lever Assembly #19.71.00.100 - Lock Base Wood Window Application #12617 - Latch with trigger #12743 - Latch without trigger Vinyl Window Application #12744 - Bolt location "A" #12745 - Bolt location "C" Note: Latches with variable trigger lengths available. Contact Truth for additional information. Latches (2 required) #22196 - Strap (24,000 foot roll) #41333. - Keeper, or #42059. - Keeper OPTIONAL: #19. 73.. 100 - Secondary Housing/Lever Assembly #19. 72. 00. 100 - Secondary Lock Base Required Tools for connecting the strap (Not included): Two 1/16" Allen Wrenches Base: 2 - #8 Pan head screws Keeper: 2 - #8 Flat head screws Latches: 2 -#6 Flat head Types of screws required determined by material of profile used. Refer to drawings for complete information on screw type and quantity needed (sold separately). For additional information on screw selection - see Truth Tips. TRuTH TIPS: 1. When two locks are used on one window, the placement of each lock, with respect to its keeper, becomes very critical to maintain a constant weather seal on all sides of the window and to insure that each lock engages properly with its keeper. 2. For vinyl window applications, mounting screws should pass through two PVC walls, or one PVC wall and one insert wall INCLuDE TRuTH SPECS ON YOuR NET WINDOW PROJECT Recess mounted check rail lock whose lever activates the enclosed tilt latches shall be included which will increase security and weather seal tightness. The lock must provide easy operation and provide a pick resistant base plate which protects the cam thus providing increased security. Window check rail locks will be of internal cam design to provide optimum pull-in to aid in sealing the meeting rails. Window locks and tilt latches will be 19 Series Fusion System as manufactured by Truth Hardware. 15a

19 FuSION SYSTEM FIG. 1 FUSION SNAP LOCK FOR WOOD AND VINYL APPLICATIONS 3.044 [77.3 mm] 1.522 [38.7 mm] 1.334 [33.9 mm].312 [7.9 mm].320 [8.1 mm] 1.699 [43.2 mm].571 [14.5 mm].385 [9.8 mm] FIG. 71.00.100 2 19.71.00.100 BASE FOR BASE WOOD FOR AND WOOD VINYL AND APPLICATIONS VINYL APPLICATIONS 2 R.600 [15.2 mm] 1.241 [31.5 mm] 2.108 [53.5 mm] 2.490 [12.4 mm].461 [11.7 mm] 2.854 [72.5 mm].312 [7.9 mm].530 [13.5 mm] (QTY 2)#8 PAN HEAD SCREWS (LENGTH AND THREAD TYPE DETERMINED BY PROFILE) 15b

19 FuSION SYSTEM FIG. 3 FUSION LOCK ASSEMBLY FOR WOOD APPLICATION ETERIOR VIEW INTERIOR VIEW COVER ASSEMBLY 19.70..100 STRAP 22196 BASE ASSEMBLY 19.71.00.100 LATCH 12617 STRAP GUIDE (INCLUDED WITH BASE 19.71.00.100) LATCH 12617 15c

19 FuSION SYSTEM FIG. 4 FUSION KEEPER ASSEMBLY FOR WOOD APPLICATION KEEPER 41333. 15d

19 FuSION SYSTEM FIG. 5 FUSION LOCK APPLICATION FOR WOOD APPLICATIONS 2 R.250 [6.4 mm] 2.857 [72.6 mm].325 [8.3 mm] 1.250 [31.8 mm].334 [8.5 mm] 1.152 [29.3 mm] 2.867 [72.8 mm] R.625 [15.9 mm] FULL R [19.0 mm].750 A A.425 [10.8 mm] 2 3.125.935 [79.4 mm] [23.7 mm] 2.188 [4.8 mm] SECTION A-A CUSTOMER DEPENDANT 4 R.312 [7.9 mm].574 [14.6 mm].550 [14.0 mm].045 [1.1 mm] CUSTOMER DEPENDANT.184 [4.7 mm] 1.148 [29.2 mm] 15e.679 [17.2 mm] Ø.625 [15.9 mm].092.472 [2.3 mm] [12.0 mm].944 [24.0 mm] BOTH SIDES

19 FuSION SYSTEM FIG. 6 FUSION LATCH 12617 (FOR WOOD APPLICATIONS) 2.345 [59.6 mm].188 [4.8 mm] 1.135 [28.8 mm].466 [11.8 mm].930 [23.6 mm].562 [14.3 mm] Ø.610 [15.5 mm].306 [7.8 mm].382 [9.7 mm] 2.915 [74.0 mm].092 [2.3 mm] (QTY 2)#4,#5,or #6 PHILLIPS FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE).154 [3.9 mm] FIG. 7 KEEPER 41333 (FOR WOOD APPLICATIONS) FIG. 7 KEEPER 41333 (FOR WOOD APPLICATIONS).952 [24.2 mm] FOR OTHER LENGTHS CONTACT TRUTH.077 [2.0 mm] 4 R.312 [7.9 mm].280 [7.1 mm].560 [14.2 mm].375 [9.5 mm].750 [19.0 mm].500 [12.7 mm] 3.044 [77.3 mm].308 [7.8 mm].420 [10.7 mm] 40 1.000 [25.4 mm] 2.000 [50.8 mm] 2.844 [72.2 mm] CONTACT TRUTH FOR OTHER OPTIONS.326 [8.3 mm].320 [8.1 mm] (QTY 2)#8 PHILLIPS FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 15f

19 FuSION SYSTEM P F FIG. 8 FUSION 8 FUSION LOCK LOCK ASSEMBLY ASSEMBLY (FOR VINYL (FOR APPLICATIONS) VINYL APPLICATIONS) ETERIOR VIEW INTERIOR VIEW COVER ASSEMBLY 19.70..100 STRAP 22196 BASE ASSEMBLY 19.71.00.100 STRAP GUIDE (INCLUDED WITH BASE 19.71.00.100) LATCH 12744 LATCH 12744 15g

19 FuSION SYSTEM FIG. 9 FUSION KEEPER ASSEMBLY (FOR VINYL APPLICATIONS) 15h

19 FuSION SYSTEM FIG. 10 FUSION KEEPER APPLICATION (FOR VINYL WINDOW APPLICATIONS) 2.750 [69.8 mm].342 [8.7 mm] 1.250 [31.8 mm].334 [8.5 mm] 1.152 [29.3 mm] 2.857 [72.6 mm] R.625 [15.9 mm] FULL R.750 [19.0 mm] 2.765 [70.2 mm].453 [11.5 mm] CUSTOMER DEPENDENT 2.000 [50.8 mm] FULL R KEEPER LAYOUT 15i

19 FuSION SYSTEM FIG. 11 FUSION APPLICATION FOR VINYL WINDOWS WITH INSERTS.875 MIN/2.000 MA.425 [10.8 mm].925 23.5 mm REINFORCING INSERT POSITIONING (1.391 MIN) [35.3 mm] (1.250 PLUS VINYL WALL THICKNESS PLUS INSERT WALL THICKNESS).425 10.8 mm.782 [2.0 cm].287 [7.3 mm].500 [12.7 mm] (1.210 MIN) (1.070 PLUS VINYL WALL THICKNESS PLUS INSERT WALL THICKNESS).574 [14.6 mm] Ø.634 [16.1 mm] TANGENT TO INSERT INTERNAL WALLS 2 REINFORCING INSERT CUSTOMER DEPENDENT TOP LOCK RAIL WITH INSERT CUSTOMER DEPENDENT.063 [1.6 mm].782 [19.9 mm] Ø.625 [15.9 mm] 15j

19 FuSION SYSTEM 15k 700 WEST BRIDGE STREET, OWATONNA, MN 55060 n 507.451.5620 800.866.7884 n TRUTH.COM

DOUBLE HUNG SLIDER 19 HARMONY SYSTEM HARMONY SYSTEM Building on the popularity we received on our award-winning Fusion System, Truth Hardware has now embarked on the next generation combination lock and tilt latch system named, the Harmony System. Aptly named, as this system beautifully integrates the check rail lock and tilt latch together in a manner which creates a new level of installation ease. INTEGRATED TECHNOLOGY The Harmony System has been designed to allow the homeowner to activate the lock and tilt latches with the same device. By simply manipulating the lever on one lock, an individual can both lock or unlock their window, and activate the tilt latches to pivot the sash to allow for ease of cleaning. Manufacturers will appreciate the ease of installation - you just snap in the tilt latch, screw down the lock and you are good to go. The Harmony system even self-locates for you! Harmony System (locked) TILT LATCHES OFFERED IN TWO VERSIONS The Standard Harmony Latch and the new Harmony 7 Latch. The Standard Harmony latch version should be considered when there is an existing reinforcement surface for mounting or if the internal reinforcement can be modified. If this is not the case, then the Harmony 7 Latch version is the better choice. FEATURES & BENEFITS Lock and tilt latch release are actuated by one mechanism Quick and easy assembly Self locating features in lock and latch! Latches are hidden within the checkrail, thus producing cleaner site lines on the window. Simple routing for lock and latch Detents and icons indicate lock/unlock/tilt positions Harmony 7 latches are color coded for quick identification of correct hand Matching, non-actuating lock assembly available for applications where you don t want an integrated lock/latch! Harmony System (unlocked) LOGO OPTIONS You can personalize the Harmony System with your logo. Truth s pad printing process is a great way to highlight your company s identity and reinforce your brand in the marketplace. WARRANTY Protected under the terms of the Truth Warranty for Window & Door Manufacturers and Authorized Distributors. Refer to Truth s Terms & Conditions for further details. MATERIAL Housing assembly is powder coated diecast zinc. Latch assemblies are of a composite construction consisting of engineered plastics and stainless steel, or SST wire. FINISH Electrostatically applied, durable coatings that provide excellent resistance to chipping, scratching and corrosion resistance while maintaining color stability for years in direct sunlight. Harmony System (tilt latch retracted) Please refer to Truth s color chart for examples of Truth s most popular finish options. Truth also offers a wide range of decorative plated finishes contact Truth for additional information on availability of these finishes on specific product lines. ORDERING INFORMATION Order the Harmony System by individual components: LOCKS: (same lock used for either Harmony or Harmony 7 applications) # 19.77..010 Housing/Lever LH Lock assembly # 19.77..020 Housing/Lever RH Lock assembly # 19.78..010 Housing/Lever Assembly Passive (for use on applications without integrated latch) 15.1

19 HARMONY SYSTEM KEEPERS: (same keeper used for either Harmony of Harmony 7 applications see drawings for available keeper designs) # 45678. Keeper # 42052. Keeper # 45674. Keeper # 33676. Keeper # 45686. Keeper (special to Trustgard window design) LATCHES (Standard Harmony Latches) # 14222 Standard Harmony Latch assembly (LH) # 14223 Standard Harmony Latch assembly (RH) # 14306 Standard Harmony Latch assembly with offset (LH) # 14307 Standard Harmony Latch assembly with offset (RH) RECOMMENDED SCREWS (sold separately) 4 - # 6 Phillips Flat Head Screws (Length and thread type to be determined by profile). For additional information on screw selection see Truth Tips. TRUTH TIPS 1. When two locks are used on one window, the placement of each lock, with respect to its keeper, becomes very critical to maintain a consistent weather seal on all sides of the window and to insure that each lock engages properly with its keeper. 2. For vinyl window applications, mounting screws should pass through two PVC walls or one PVC Wall and one insert wall. The following Tilt Latches require # 45683 Cage (purchased separately): (Harmony 7 latches) # 14321 5 Tilt Latch (LH) # 14322 5 Tilt Latch (RH) # 14323 7 Tilt Latch (LH) # 14324 7 Tilt Latch (RH) # 14325 9 Tilt Latch (LH) # 14326 9 Tilt Latch (RH) 15.1a

19 HARMONY SYSTEM FIG. 1 19.77..020 RH LOCK SHOWN (19.77..010 LH LOCK) 3.000 76.2 2.000 50.8 1.500 38.1 1.313 33.3 2.56 14.29 1.188 30.2.500 12.7 RECOMMENED SCREWS: (QYT 2) #6 PHILLIPS FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 1.500 38.1.340 8.6 FIG. 2 19.78..010 LH LOCK PASSIVE SHOWN 1.500 38.1 3.000 76.2 2.000 50.8 1.313 33.3 2.56 14.29 1.188 30.2 1.719 43.67.500 12.7.340 8.6 RECOMMENED SCREWS: (QYT 2) #6 PHILLIPS FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 1.500 38.1 15.1b

19 HARMONY SYSTEM FIG. 3 LH LATCH 14222 SHOWN (RH LATCH IS 14223) 2.50 63.5 7.75 196.9.375 9.5.486 12.3.666 16.9.420 10.7.383 9.7.350 8.9 FIG. 4 LH LATCH 14306 SHOWN (RH LATCH IS 14307) 7.75 196.9.375 9.5.666 16.9.302 7.7.486 12.3.383 9.73.350 8.9 15.1c

19 HARMONY SYSTEM FIG. 5 19.77..010 AND 19.77..020 LOCK ASSEMBLY TO STANDARD HARMONY LATCHES 15.1d

19 HARMONY SYSTEM FIG. 6 19.77..010 LOCK APPLICATION 2.000 50.8 1.200 30.48 (FROM LOCK FRONT EDGE) 1.520 38.6 MIN 1.540 39.1 MA "A".563 14.3 (FROM LOCK FRONT EDGE) A A R.500 12.7.345 8.8 MIN SECTION A-A "A" 5.000" (127.0mm) 7.000" (177.8mm).506 12.85.738 18.74 (FROM LOCK FRONT EDGE).137 3.48.403 10.24 1.201 30.5 (FROM LOCK FRONT EDGE) 15.1e

19 HARMONY SYSTEM FIG. 7 19.77..020 RH LOCK SHOWN (19.77.010 LH LOCK) 3.000 76.2 2.000 50.8 1.500 38.1 1 1.313 33.3 2.56 14.29 1.188 30.2.500 12.7 RECOMMENED SCREWS: (QYT 2) #6 PHILLIPS FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 1.500 38.1.340 8.6 FIG. 8 19.78..010 LH LOCK PASSIVE SHOWN 1.500 38.1 3.000 76.2 2.000 50.8 1.313 33.3 2.56 14.29 1.188 30.2 1.719 43.7.500 12.7.340 8.6 RECOMMENED SCREWS: (QYT 2) #6 PHILLIPS FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 1.500 38.1 15.1f

19 HARMONY SYSTEM FIG. 9 5 LATCH 14321 SHOWN (5 RH LATCH IS 14322).319 8.1 Ø.490 12.4.320 8.1 6.75 171.4.375 9.5.190 4.8 FIG. 10 7 14323 LH SHOWN (7 RH LATCH 14324).319 8.1 Ø.490 12.4.320 8.1 8.75 222.2.375 9.5.190 4.8 FIG. 11 9 LH 14325 SHOWN (9 RH LATCH 14326).319 8.1 Ø.490 12.4.320 8.1 10.75 273.0.375 9.5.190 4.8 15.1g

19 HARMONY SYSTEM FIG. 12 45683 CAGE R.505 12.8 1.243 31.6.395 10.0 1.61 40.9.445 11.3 15.1h

19 HARMONY SYSTEM FIG. 13 19.77..010 AND 19.77..020 LOCK ASSEMBLY TO HARMONY 7 LOCK LATCHES 15.1i

19 HARMONY SYSTEM FIG. 14 19.77 HARMONY 7 LOCK APPLICATION "A" 2.000 50.8 A A 1.248 31.69 (FROM LOCK FRONT EDGE) R.500 12.7.563 14.3 (FROM LOCK FRONT EDGE) 1.620 MIN 41.1 1.640 MA 41.7.400 10.2 MIN SECTION A-A SCALE 1 : 1 "A" 5.000" (127.0) 7.000" (177.8) 9.000" (228.6).328 8.3 Ø.500 12.70 2.500 MIN 1.254 MA 31.8 (FROM LOCK FRONT EDGE).629 MIN 16.0 (FROM LOCK FRONT EDGE).789 MIN SET BACK 20.0 (FROM LOCK FRONT EDGE) 1.414 MA SET BACK 35.9 (FROM LOCK FRONT EDGE) 15.1j

19 HARMONY SYSTEM FIG. 15 42052. KEEPER 1.750 44.5.17 4.31 1.38 35.10 (QTY 2) #6 PHILLIPS FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 1.00 25.40 Ø.150 3.8.24 6.19 FIG. 16 45674. KEEPER 1.750 44.5.20 5.17 1.42 35.97 1.00 25.40 Ø.150 3.8.38 9.68 (QTY 2)#6 PHILLIPS FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 15.1k

19 HARMONY SYSTEM FIG. 17 45678. KEEPER 2.000 50.8.14 3.48 3.000 76.2 Ø.275 7.0.59 14.99.340 8.64 (QTY 2) #6 PHILLIPS FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE).249 6.33.32 8.13 FIG. 18 33676. KEEPER 1.75 44.5.250 6.35.559 14.2.18 4.50 3.00 76.20.47 11.9 1.41 35.72 (QTY 2) #6 PHILLIPS FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 15.1l

19 HARMONY SYSTEM 15.1m 700 WEST BRIDGE STREET, OWATONNA, MN 55060 507.451.5620 800.866.7884 TRUTH.COM

DOUBLE HUNG SLIDER TILT LATcHES Truth Hardware Tilt Latches are designed to provide window manufacturers the highest quality product at a minimum cost. With several variations to choose from, these Tilt Latches are engineered with labor saving and design features to fit virtually every existing window profile in today s marketplace. MOUNTING OPTIONS Options include Truth s revolutionary snap-in mount and the hidden mounting fastener, as well as ourstandard top mounted fasteners each of which affords dependable operation with secure methods for installation. (See following drawings for available options). WARRANTY: Protected under the terms of the Truth Warranty for Window & Door Manufacturers & Authorized Distributors. Refer to Truth s Terms & Conditions for further details MATERIAL: Composite assemblies of powder coated cast zinc and/or thermoplastics. ORDERING INFORMATION & OPTIONS: 1.Choose Tilt Latch style (specify by part number). 2.Specify left or right hand (if necessary). 3.Order screws required (if necessary). 4.Specify desired finish. FINISH: Electrostatically applied, durable coatings that provide excellent resistance to chipping, scratching and corrosion while maintaining color stability for years in direct sunlight. Please refer to Truth s Color Chart for examples of Truth s most popular finish options. Truth also offers a wide range of decorative plated finishes contact Truth for additional information on availability of these finishes on specific product lines. 16

9750 TILT LATcHES FIG. 1 46.20..001 TILT LATCH.343 [8.7 mm] LEFT HAND SHOWN 46.20..001 LEFT HAND 46.20..002 RIGHT HAND.281 [7.1 mm].050 [1.3 mm].060 [1.5 mm].687 [17.4 mm].714 [18.1 mm] 2.625 [66.7 mm].375 [9.5 mm].315 [8.0 mm].082 [2.1 mm].055 [1.4 mm].425 [10.8 mm] 2.550 [64.8 mm].285 [7.2 mm] FULL R 2.563 [65.1 mm] TOP END.578 [14.7 mm] ROUTING DETAIL.375 [9.5 mm] 16a

9750 TILT LATcHES FIG. 2 46.21..001 TILT LATCH LEFT HAND SHOWN.050 [1.3 mm].343 [8.7 mm] 46.21..001 LEFT HAND 46.21..002 RIGHT HAND.281 [7.1 mm].060 [1.5 mm].687 [17.4 mm].714 [18.1 mm] 2.625 [66.7 mm].375 [9.5 mm].315 [8.0 mm].082 [2.1 mm].055 [1.4 mm].425 [10.8 mm] 2.550 [64.8 mm].285 [7.2 mm] FULL R 2.563 [65.1 mm] TOP END.578 [14.7 mm] ROUTING DETAIL.375 [9.5 mm] 16b

9750 TILT LATcHES FIG. 3 46.11 TILT LATCH 2.932 [74.5 mm].843 [21.4 mm].380 [9.6 mm].268 [6.8 mm].060 [1.5 mm].168 [4.3 mm].865 [22.0 mm].685 [17.4 mm].810 [20.6 mm] 1.785 [45.3 mm].103 [2.6 mm].460 [11.7 mm] 2.843 [72.2 mm].268 [6.8 mm] RECOMMENDED SCREW: LEFT HAND SHOWN 46.11..101 LEFT HAND 46.11..102 RIGHT HAND WOOD/PVC: (QTY 2)#8 PHILLIPS FLAT HEAD SCREWS(LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE.) FIG. 4 46.12 TILT LATCH 2.932 [74.5 mm].160 [4.1 mm].385 [9.8 mm].513 [13.0 mm].060 [1.5 mm].685 [17.4 mm].168 [4.3 mm].810 [20.6 mm] 1.785 [45.3 mm].281 [7.1 mm].865 [22.0 mm].460 [11.7 mm] 2.843 [72.2 mm].103 [2.6 mm].268 [6.8 mm] LOCKING TAB 2.065 [52.5 mm] NON HANDED RECOMMENDED SCREW: SECTION A-A WOOD/PVC: (QTY 2)#8 PHILLIPS FLAT HEAD SCREWS(LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE.) 16c

TILT LATcHES FIG. 5 1038L TILT LATCH (SNAP IN) LEFT HAND SHOWN.276 [7.0 mm].060 [1.5 mm].135 [3.4 mm].733 [18.6 mm] CL 2.450 [62.2 mm].355 [9.0 mm].440 [11.2 mm].108 [2.7 mm].080 [2.0 mm] 1.074 [27.3 mm] A 2.420 [61.5 mm] A.235 [6.0 mm] 42 LEFT HAND SHOWN.566 [14.4 mm] 1038L. LEFT HAND 1038R. RIGHT HAND SNAP IN TAB 2.350 [59.7 mm].683 [17.3 mm] SECTION A-A FIG. 6 4200 & 4210 TILT LATCH 2.610 [66.3 mm].862 [21.9 mm].262 [6.7 mm].325 [8.3 mm].555 [14.1 mm] LC.672 [17.1 mm] 4200L. LEFT HAND 4210R. RIGHT HAND.295 [7.5 mm].120 [3.0 mm].122.210 [3.1 mm] [5.3 mm] LEFT HAND SHOWN RECOMMENDED SCREW: 2.120 [53.8 mm].235 [6.0 mm] WOOD/PVC: (QTY 1)#8 PHILLIPS FLAT HEAD SCREWS(LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE.) 16d

TILT LATcHES FIG. 7 4260 TILT LATCH.670 [17.0 mm] 2.597 [66.0 mm].354 [9.0 mm].135 [3.4 mm].075 [1.9 mm].550 [14.0 mm] 1.25 [31.7 mm] 24.315 [8.0 mm].670 [17.0 mm].108 [2.7 mm].329 [8.4 mm].237 [6.0 mm] RIGHT HAND SHOWN 4260. RIGHT HAND 4270. LEFT HAND.050 [1.3 mm] 2.547 [64.7 mm].070 [1.8 mm] (1 QTY) #8 SCREW WITH A #7 HEAD (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) FIG. 8 4250 TILT LATCH 3.082 [78.3 mm].288 [7.3 mm].086 [2.2 mm] C.958 [24.3 mm] 1.554 [39.5 mm].162 [4.1 mm].560 [14.2 mm].495 [12.6 mm].314 [8.0 mm].132 [3.4 mm].096 [2.4 mm] NON-HANDED.050 [1.3 mm] 2.955 [75.1 mm].234 [5.9 mm] (1 QTY) #8 SCREW WITH A #7 HEAD (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 16e

TILT LATcHES FIG. 9 46.13 TILT LATCH 2.870 [72.9 mm] 1.483 [37.7 mm].440 [11.2 mm].375 [9.5 mm].080 [2.0 mm].085 [2.2 mm].543 [13.8 mm].077 [2.0 mm].223 [5.7 mm].080 [2.0 mm].315 [8.0 mm].750 [19.0 mm].550 [14.0 mm].507 [12.9 mm] LEFT HAND SHOWN 46.13.32.101 LEFT HAND 46.13.32.102 RIGHT HAND.430 [10.9 mm] 2.500 [63.5 mm] WOOD/PVC (QTY 1) #6 PHILLIPS FLAT HEAD SCREWS (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 16f

16g 700 west bridge street, owatonna, mn 55060 n 507.451.5620 800.866.7884 n TRUTH.COM

DOUBLE HUNG SLIDER SASH LIFTS Truth Sash Lifts help provide easy opening and closing of all double-hung or sliding windows. Truth s new #18.16 Series Restoration Sash Lift with its traditional finger-pull look, is designed to complement Truth s #17.02 Series Restoration Lock. Truth s Sash Lifts encourage the lifting of the window from the bottom, thereby putting less stress on the sash than would occur from pushing on the top rail. Durable baked enamel finishes are available to match Truth Check Rail Locks. WARRANTY: Protected under the terms of the Truth Warranty for Window & Door Manufacturers & Authorized Distributors. Refer to Truth s Terms & Conditions for further details. MATERIAL: High-pressure, corrosion resistant, die-cast zinc. FINISH: Electrostatically applied, durable coatings that provide excellent resistance to chipping, scratching and corrosion while maintaining color stability for years in direct sunlight. Please refer to Truth s Color Chart for examples of Truth s most popular finish options. Truth also offers a wide range of decorative plated finishes contact Truth for additional information on availability of these finishes on specific product lines. ORDERING INFORMATION & OPTIONS: 1. Choose Sash Lift style (specify by part number). 2. Specify finish number. Types of screws required determined by material of profile used (sold separately). For additional information regarding screw selection - see Truth Tips. TRUTH TIPS: 1. For accurate hardware placement in vinyl or metal applications, pre-drilling of the window profile is recommended. 2. For vinyl window applications, mounting screws should pass through two PVC walls, or one PVC wall and one insert wall. For this reason, it may be necessary to use a longer screw than is recommended. 3. For metal window profiles, Truth recommends stainless steel machine screws. However, in most applications, stainless steel sheet metal screws will provide adequate holding power. INCLUDE TRUTH SPECS ON YOUR NET WINDOW PROJECT Window sash handles shall be included which will provide a positive grip on the sash for easy window operation, while having a low profile appearance. The sash handles shall be constructed of a high pressure zinc alloy die casting. Window handles/sash lifts shall be manufactured by Truth Hardware. 17

18.10 SASH LIFTS FIG. 1 18.10 SASH LIFT 3.310 [84.1 mm].375 [9.5 mm].755 [19.2 mm] 4.000 [101.6 mm] WOOD: (QTY 2) (P/N 19380) #8 PHILLIPS, FLAT HEAD, SHEET METAL SCREWS PVC/METAL: (QTY 2) #10 PHILLIPS, FLAT HEAD (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) FIG. 2 18.11 SASH LIFT 3.800 [96.5 mm] 1.118 [28.4 mm] 1.115 [28.3 mm].187 [4.7 mm] 3.250 [82.6 mm] WOOD: (QTY 2) (P/N 19380) #10 1.0 PHILLIPS, FLAT HEAD, SHEET METAL SCREWS PVC/METAL: (QTY 2) #10 PHILLIPS, FLAT HEAD (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 17a

18.10 SASH LIFTS FIG. 3 18.16 SASH LIFT.972 [24.7 mm] 1.275 [32.4 mm].900 [22.9 mm].341 [8.7 mm].750 [19.0 mm] 1.654 [42 mm] (QTY 2) #8-32 PHILLIPS FLAT HEAD SREW (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) FIG. 4 11861. SASH LIFT.978 [24.8 mm].126 [3.2 mm] 4.063 [103.2 mm].282 [7.2 mm] 3.498 [88.9 mm] (QTY 2) #8-32 PHILLIPS FLAT HEAD SREW (LENGTH AND THREAD TYPE TO BE DETERMINED BY PROFILE) 17b

18.10 SASH LIFTS FIG. 5 30665. RECESSED SASH LIFT 2.500 [63.5 mm] Ø.281 [7.1 mm].745 [18.9 mm].175 [4.4 mm].650 [17 mm] R.375 4.000 [101.6 mm] ROUTING 1.250 [32 mm].750 [19.0 mm].170 [4.3 mm].300 [7.6 mm] WOOD: (QTY 2) (P/N 19051) #6 1" PHILLIPS FLAT HEAD SHEET METAL SCREWS..050 [1.3 mm] 17c ٥٥٠٦٠ n ٥٠٧.٤٥١.٥٦٢٠ ٨٠٠.٨٦٦.٧٨٨٤ n TRUTH.COM خح ءخخدشءطد ش زشس اءةز شس ط ٧٠٠

DOUBLE HUNG SLIDER WINDOW ROLLERS Truth Hardware offers a wonderful series of rollers designed specifically for the window market. Truth s 4231 and 4233 Series Window Rollers help create almost effortless travel for slider windows. Available with brass wheels and mounted into a sturdy nylon case, Truth s Window Rollers will produce long-lasting reliable service for the homeowner. Truth s window rollers are rated for up to a 30 lb. sash (2 rollers per sash). Please refer to the following drawings to see the models available. WARRANTY: Protected under the terms of the Truth Warranty for Window & Door Manufacturers & Authorized Distributors. Refer to Truth s Terms & Conditions for further details. ORDERING INFORMATION & OPTIONS: Because of the variety of slider windows on the market, Truth Hardware suggests that you contact our Product Specialists to help you identify the components that will best meet your requirements. To assist us in helping you identify the product that you need, please be prepared to provide Truth with: 1. The type and style of profile that you are mounting the hardware to. 2. The Truth Hardware Model Number that you are interested in. 18

WINDOW ROLLERS FIG. 1 4233-1000 ROLLER 1.500 [38.1 mm].556 [14.1 mm].416 [10.5 mm].435 [11.0 mm].500 [12.7 mm].090 [2.2 mm].230 [5.8 mm] 1.380 [35.0 mm].055 [1.3 mm] 1.420 [36.0 mm] FIG. 2 4231-1000 ROLLER 1.360 [34.5 mm].500 [12.7 mm] 1.38 [35.0 mm].380 [9.6 mm].562 [14.2 mm].500 [12.7 mm].400 [10.1 mm].062 [1.5 mm] 1.500 [38.1 mm].170 [4.3 mm] 18a 700 west bridge street, owatonna, mn 55060 n 507.451.5620 800.866.7884 n TRUTH.COM

DOUBLE HUNG SLIDER PIVOT BARS Truth Hardware offers a complete line of Pivot Bars designed to accommodate most window profiles and application needs. Please refer to the following drawings to see the models available. WARRANTY: Protected under the terms of the Truth Warranty for Window & Door Manufacturers & Authorized Distributors. Refer to Truth s Terms & Conditions for further details. ORDERING INFORMATION & OPTIONS: Because of the variety of windows on the market, Truth Hardware suggests that you contact our Product Specialists to help you identify the Pivot Bars that will best meet your requirements. To assist us in helping you identify the product that you need, please be prepared to provide Truth with: 1. The type and style of profile that you are mounting the hardware to. 2. The Truth Hardware Model Number that you are interested in. FIG. 1 23095 PIVOT BAR.665 [16.9 mm].638 [16.2 mm].420 [10.7 mm].081 [2.1 mm].375 [9.5 mm] R.313 [7.9 mm] 2 Ø.163 Ø.280.313 [8.0 mm].078 [2.0 mm].674 [17.1 mm] FIG. 2 32935 LH PIVOT BAR NO WINGS.054 [0.1 cm].057 [0.1 cm].343 [8.7 mm] 3 Ø.120 [3.0 mm] Ø.485 [12.3 mm].323 [8.2 mm].568 [14.4 mm].180 [4.6 mm] 1.293 [32.8 mm].189 [4.8 mm].083 [2.1 mm].311 [7.9 mm] FIG. 3 32934 RH PIVOT BAR NO WINGS.057 [1.5 mm].343 [0.9 cm].055 [1.4 mm] 3 Ø.120 [0.3 cm] Ø.485 [12.3 mm].083 [2.1 mm].568 [14.4 mm].180 [4.6 mm] 1.293 [32.8 mm].189 [4.8 mm].323 [8.2 mm].311 [7.9 mm] 19

PIVOT BARS FIG. 4 32937 PIVOT BAR.071 [1.8 mm].187 [4.7 mm].102 [2.6 mm].054 [1.4 mm] 3 Ø.120 [3.0 mm].057 [1.5 mm].463 [11.8 mm].343 [8.7 mm].100 [2.5 mm].312 [7.9 mm].568 [14.4 mm].180 [4.6 mm] 1.293 [32.8 mm].189 [4.8 mm] Ø.485 [1.2 cm].312 [7.9 mm] 1.000 [25.4 mm] FIG. 5 32936 RH PIVOT BAR.568 [14.4 mm] 1.293 [32.8 mm].180 [4.6 mm].189 [4.8 mm].463 [11.8 mm] Ø.485 [12.3 mm].312 [7.9 mm].312 [7.9 mm].072 [1.8 mm].102 [2.6 mm] 3 Ø.120 [3.0 mm].568 [14.4 mm].100 [2.5 mm] 1.000 [25.4 mm].187 [4.7 mm].054 [1.4 mm].057 [1.5 mm].343 [8.7 mm] FIG. 6 32794 PIVOT BAR.620 [15.7 mm] 2.893 [73.5 mm].468 [11.9 mm].350 [8.9 mm].398 [10.1 mm].233 [5.9 mm].311 [7.9 mm] 1.331 [33.8 mm].108 [2.7 mm].034 [0.9 mm] 1.344 [34.1 mm] 19a 700 WEST BRIDGE STREET, OWATONNA, MN 55060 n 507.451.5620 800.866.7884 n TRUTH.COM

DOUBLE HUNG SLIDER MISCELLANEOUS Truth Hardware offers Vent Stops as an accessory for your sliding window. These snap-fit plastic components help limit the travel of the sliding window. WARRANTY: Protected under the terms of the Truth Warranty for Window & Door Manufacturers & Authorized Distributors. Refer to Truth s Terms & Conditions for further details. FIG. 1 22833 VENT STOP 1.025 [26.0 mm].112 [2.8 mm] 2.240 [56.9 mm] 2.187 [55.5 mm].595 [15.1 mm].240 [6.1 mm] 1.025 [26.0 mm] 20

MISCELLANEOUS 20a 700 WEST BRIDGE STREET, OWATONNA, MN 55060 n 507.451.5620 800.866.7884 n TRUTH.COM