Think wall. We have designed a wallcovering to satisfy any decorative need.

Think wall We have designed a wallcovering to satisfy any decorative need.

Appropriate for use on almost any wallcovering application. Available in many ABET LAMINATI colours and fi nishes. Suitable for applications where acoustic deadening is needed but also valuable for its effective design due to the profi led surface. Renders a warm and elegant covering for any space; seven coloured textures offered.

Parqwall 2 Abet Laminati presents a new look called Parqwall, which incorporates new technical mounting solutions. The cladding system is available with either vertical or horizontal panels in 400 mm or 600 mm widths (15 11/16 or 23 9/16 ). Parqwall is now available with both visible anodized aluminum joints and fold-away joints, which allow the cladding material to display a completely unbroken surface. Special joints have also been produced, which allow both horizontal and vertical fixing of shelves and coat racks. The installation procedure has been made considerably easy with the new profiles. New colours with no required minimum quantity have been added to the range. For additional noise reduction, we recommend the attachment of an insulating material i.e. glass fibre, rock wool etc., to the wall surface.

p The Parqwall cladding system makes it possible to clad walls of any type and in any condition. It is easy to install and a quick solution to refurbishing problems in rooms for which there are no special restrictions regarding the subsequent use of the premises. Parqwall cladding system with horizontal panels and visible anodized aluminum joints.

Parqwall 4 Parqwall cladding system with vertical panels and visible anodized aluminum joints. The Parqwall system can be installed directly on existing walls if they are suffi ciently straight and dry. Should Parqwall be installed on old, damp or uneven walls, it is recommended to leave a gap between the wall and the Parqwall system. The Parqwall system can be installed on vertical or horizontal wood spacers or on a galvanized steel frame (Knauf system or similar).

Parqwall exhibits the same characteristics as those of a wooden panel, therefore it is important to ensure good ventilation behind the cladding panels. When building the frame, remember that the Parqwall panels should be mounted at a distance of at least 5 mm (3/16 in.) from the fl oor, to enable ventilation of the cavity behind. When cladding particularly damp walls, the Parqwall panels should fi nish at a distance of at least 50 mm (1 15/16 in.) from the fl oor. This will protect the base of the panel from the risk of dampness being absorbed from the fl oor.

Silentwall 6 Silentwall is a noise reducing component of the modular Parqwall system. Silentwall is designed to absorb noise from highly frequented rooms, which have a high level of background disturbance. Silentwall is suitable for theatres, cinemas, auditoriums and convention halls where sound reduction is necessary.

p Silentwall is a noise reducing component of the modular Parqwall system. Silentwall cladding system with vertical panels and visible anodized aluminum joints.

Hanging accesoires Parqwall p Silentwall 8 Rack joints allow the installation of several types of shelves. When the panels are fitted horizontally, the use of rack joints allow the installation of a wide range of coat racks for offices and shops. Panels installed horizontally with rack joints. Panels installed vertically with the use of rack joints. a b

p The special joints allow the installation of shelves and coat racks on the Parqwall and Silentwall systems. Parqwall cladding system with vertical panels and the fitting of the rack joints.

10 ABET LAMINATI takes you to the next aesthetic level by recouping and reworking otherwise wasted leather refuse. Waste material is renewed by combining leather fi bers with a vegetable tanning process mixed with the latex of natural rubber. ABET LAMINATI interior wall panels can be installed in a vertical or horizontal pattern using extruded aluminum profi les as visible accents or as non-visible components. The panel is composed of a high density core clad in leather.

p Technology and design merge beautifully to create a leather wall cladding system by ABET LAMINATI. The warm qualities of leather naturally enrich interior spaces producing exquisitely textured surfaces. Parqleather cladding system with vertical panels and visible anodized aluminum joints.

Decors range Parqwall p Silentwall 12 Parqwall and Silentwall are made of Print high-pressure laminate (HPL) available in an extremely wide range of finishes, colours and wood effects. Architects and interior designers can accomplish their projects without any aesthetic restrictions and with total creative expression. They can create bright, pleasant and very comfortable rooms, even in conditions where the existing architectural structure is particularly run down. Parqwall and Silentwall can be produced without any minimum quantity in the range shown here, designed to fulfill the most demanding market requests. However, it is possible to manufacture the Parqwall and Silentwall cladding systems in other colours and patterns offered in the ABET LAMINATI HPL range. colours and texture 410 Microline 854 Microline 810 Microline 418 Microline 413 Microline 869 Microline 893 Microline 473 Microline 477 Microline 870 Microline 871 Microline 476 Microline 479 Microline 420 Microline 868 Microline 867 Microline 846 Millerighe2 458 Millerighe2 857 Millerighe2 482 Millerighe2 499 Millerighe2 484 Millerighe2 425 Millerighe2 423 Millerighe2 428 Millerighe2 441 Millerighe2

460 Millerighe2 463 Millerighe2 469 Millerighe2 494 Millerighe2 835 Millerighe2 834 Millerighe2 410 Grana2 409 Grana2 457 Grana2 443 Grana2 444 Grana2 1802 Grana2 1803 Grana2 858 Grana2 867 Grana2 893 Grana2 837 Grana2 410 406 810 418 854 413 416 479 420 466 454 1809 1810 472 879 421 406 Grainwood 812 Grainwood 800 Grana2 803 Grana2 496 Grana2 1804 Grana2 472 Grana2 476 Grana2 1808 Grana2 colours and texture

Decors range Parqwall p Silentwall 14 colours and texture 869 Grainwood 868 Grainwood 867 Grainwood 893 Grainwood 837 Grainwood 897 Grainwood 879 Grainwood 421 Grainwood colours fi nitura Sei 410 Bianco Ghiaccio 406 Bianco Primavera 411 Bianco 810 Mini Bianco 409 Latte 418 Panna Crema 854 Silver Bleu 478 Grigio Chiaro 413 Beige Ardenne 414 Sabbia 479 Grigio Tortora 473 Grigio Lapponia 495 Verde Grigiato 475 Grigio Perla 420 Beige Pastello 869 Grigio Alpaca 1809 Azzurro Koala 477 Grigio 1819 Grigio Monviso 480 Grigio Plomo 870 Grigio Lastra 868 Grigio Medio 1810 Grigio Autunno 1820 Grigio Cosmico 867 Grigio Cielo 871 Grigio Scuro

colours 476 Grigio Inox 472 Grigio Londra 879 Grigio Grafi te 421 Nero 466 Mini Giallo 412 Avorio 462 Giallo Ananas 467 Giallo Paglierino 464 Giallo Chiaro 463 Giallo Pom-Pom 468 Giallo Canarie 469 Giallo Africa 860 Giallo Piper 470 Giallo Tigre 1801 Giallo Ocra 862 Giallo Savana 1812 Giallo Polenta 861 Giallo Pop 822 Melone 835 Arancio Canyon 834 Rosso Woom 432 Terra Ocra 823 Rosso Tango 431 Rosso 435 Rosso Antico 828 Rosa Baby 827 Rosa Singapore 866 Giallo Champagne 830 Rosa Crazy Horse 494 Bouganville 427 Porpora 417 Rosso Terracotta 1813 Magnolia 813 Beige Manhattan 415 Beige Chenise 416 Beige 829 Yaqui 812 Rosa Viola 843 Verde Pace 842 Verde Sub 446 Verde Pastello 1816 Sahara Beige

Decors range Parqwall p Silentwall 16 colours 892 West Brown 893 Terra d Ombra 894 Viola Fumo 837 Sarmiento 898 Bruno Fiandra 897 Bruno Vulcano 1805 Rosa Nespola 890 Darling Beige 887 Apricot Brown 891 Scotch Brown 1806 Ruggine 895 Bruno Cherry 831 Rosso Mattone 429 Viola Cerise 424 Viola Tramonto 836 Rosso Prugna 1811 Rosso Barolo 832 Rosso Lord 453 Verde Papiro 454 Verde Caraibi 457 Verde Cenere 452 Verde Lichene 443 Mini Verde 485 Azzurro Mary 486 Azzurro Lago 1802 Verde Alga 841 Verdino 846 Turchese 458 Verde Libellula 444 Verde Salvia 445 Verde Chiaro 459 Verde Estate 497 Turchese Cobalto 491 Bleu Tundra 492 Verde Bond Street 1803 Verde Militare 456 Verde 488 Verde Prussia 441 Verde Cedro 460 Verde Erbetta 451 Sempreverde 839 Verde Acqua

colours 437 Blu Giungla 490 Verde Mogul 438 Verde Mariaci 845 Verde Versailles 440 Verde Biliardo 450 Verde Lauro 455 Verde Ardizio 481 Celeste Mattino 483 Azzurro Maldive 857 Celeste Myosotis 853 Bleu Spazio 487 Azzurro Polvere 858 Azzurro Pervinca 801 Azzurro Tempesta 484 Blu Zaffi ro 847 Azzurro 482 Bleu Panarea 499 Bleu California 430 Lilla Gemini 838 Bleu Primario 859 Blu Faenza 1804 Blu Tenebre 1818 Blu Intenso 851 Blu Cobalto 428 Blu Elettrico 496 Blu Esperia 849 Blu Pavone 1814 Azzurro Acqua 856 Blu Acciaio 850 Bleu Rada 1808 Blu Petrolio 852 Big Bleu 805 Rosa Plumbeo 802 Blu Ice 804 Calendula 425 Lilla Erica 423 Viola Madras 498 Viola Giglio

Decors range Parqwall p Silentwall 18 serie cresp 1422 Cresp 1522 Cresp Due 1419 Cresp 1424 Cresp 1524 Cresp Due 1420 Cresp 1520 Cresp Due 1413 Cresp 1513 Cresp Due 1421 Cresp 1521 Cresp Due 1415 Cresp 1515 Cresp Due 1414 Cresp 1410 Cresp 1423 Cresp 1523 Cresp Due 1418 Cresp 1518 Cresp Due vertical line fi nitura Sei 251 244 200 202 243 Soft 255 Soft 265 Soft fiber 1087 1030 1089 1091 1086

fiber 1097 1032 1038 1039 1048 1046 1047 milano fi nitura Soft 1170 1123 1114 1134 1117 1137 1100 1120 1101 1121 1107 1127 1171 1140 1106 1126 1177 1149 1116 1136 1168 1146 1104 1124 1112 1132

Decors range Parqwall p Silentwall 20 legni 388 Douglas Microline 381 Douglas Chiaro Microline 387 Douglas Scuro Microline 382 Douglas Medio Microline 392 Douglas Microline 389 Douglas Microline 391 Douglas Microline 659 Pino Svizzera Microline 660 Pino Savoia Microline 661 Pino Chambery Microline 316 Pommier Morbida 1642 Pero Italiano Soft 367 Pero Svizzero Morbida 1637 Pero Marine Soft 324 Acero Bahia Sei Due 1678 Acero Due Morbida 385 Acero Sei Due 1677 Acero Due Morbida 364 Ontano Chiaro Morbida 365 Ontano Medio Morbida 1618 Noce Rosato Sei Due 362 Noce Torino Morbida 1636 Noce Italiano Morbida

legni 1329 Noce Bossea Morbida 1328 Noce Rigato Morbida 1365 Noce Top Morbida 624 Noce Roero Sei Due 358 Noce Crea Morbida 1621 Teak Maldive Morbida 1612 Teak Sumatra Sei Due 321 Teak Asia Sei Due 384 Rovere Toscano Sei Due 383 Rovere Europa Sei Due 1355 Oak Sei Due 658 Oak Nature Sei Due 386 Rovere Nazionale Sei Due 1619 Rovere Trasv.le Sei Due 1661 Rovere Montano Morbida 1379 Rovere Sud Morbida 650 Rovere Texas Sei Due 653 Rovere Dallas Sei Due 657 Rovere America Sei Due 655 Rovere Riverwalk Sei Due 656 Rovere Tennessee Sei Due 1372 Continental Oak Morbida 1321 Rovere Stiria Morbida 1322 Rovere Carinzia Morbida

Decors range Parqwall p Silentwall 22 legni 373 Rovere Trentino Morbida 1611 Ciliegio Fey Sei Due 1623 Ciliegio Americ. Soft 380 Ciliegio Europeo Sei Due 1609 Ciliegio Pavese Sei Due 1664 Ciliegio Naturale Morbida 352 Ciliegio Canino Morbida 1643 Ciliegio Rosa Morbida 370 Olmo Fine Soft 374 Castagno Morbida 1373 Mogano Virginia Morbida 354 Sucupira Morbida 1614 Frassino Beige Sei Due 1615 Frassino Rosa Sei Due 320 Frassino Lidia Sei Due 1610 Cherry Sei Due 1647 Faggio Norvegia Sei Due 1646 Faggio Italia Morbida 1666 Faggio Americ. Sei Due 1367 Faggio Veneto Morbida 323 Oak Scuro Nutshell 315 Wengè Nutshell 312 Wengè Nutshell 314 Wengè Nutshell

legni 313 Wengè Nutshell 1306 Radica Olmo Morbida 1651 Forest Sei Due 1620 Ebano Sei Due legni speciali 1317 Morbida 1304 Morbida 1628 Morbida 1309 Morbida 1324 Morbida 1354 Sei Due 1352 Sei Due 1318 Nutshell 1347 1346 1348 1342 1672 1673 1675 printwood 1697 Ciliegio Wood 1686 Ontano Wood 1706 Wengè Wood

Decors range Parqwall p Silentwall 24 printwood 1688 Betulla Tavolata fi nitura Sei Due 1699 Aframosia 1689 Faggio Wood 1696 Mutenye Wood 1684 Rovere Wood 1700 Rovere Chiaro 1701 Rovere Decapè 1704 Decapè Chiaro 1705 Decapè Grigio 1693 Tanganica Wood 1698 Noce Chiaro Tavolato Wood 1690 Teak Wood 1685 Acero Wood 1683 Olmo Americano 1649 Zebrano 1702 Zapatero Chiaro 1703 Zapatero Scuro serigrafia fi nitura Sei 1216 1210 1198

serigrafia 1238 1233 1239 1240 1242 1243 1241 1232 1230 1231 1244 digital print 5417 5418 5419 Soft 5422 Soft 5423 5533 5537 5532

Decors range 26 colours 6647 Sangue di Bue 6536 Avorio 6537 Panna 6622 Cuoio 6538 Cappuccino 6534 Testa di Moro 6249 Nero Other textures and colours available on demand.

Illustration of profiles Parqwall p Silentwall p 28 Visible profiles Special elements Head or end profile This is used as a starting or end profi le on lower, upper and lateral edges. Rack joint This is used for joining two panels to be fixed vertically and provides the cladding system with supports for shelves and other accessories. End profile for inside corners This is used for the realization of inside corners. Horizontal joint allowing the fixing of shelves and accessories This joint is used as a connecting element between two panels laid horizontally, and allows the walls to be fi tted with shelving supports and other furnishing items. Two-way joint Profi le used for joining two panels, both for horizontal and vertical installation. Double head or end profile This is a profile which can be used to join the butt edges of the panels. Fold-away profiles Fold-away profiles Structural profile which can be used as starting or end profile on lower, upper and lateral edges. Click aluminum corner joint with support This is used for joining the butt edges of the panels and especially the covering of pillars. Fold-away two-way joint This is used for joining two panels, both for horizontal and vertical installation. Panelling end profile This is an MDF profile which can be painted and used as an upper and lateral panelling plugging profile and is inserted in the head or end profile.

Illustration of profiles Parqwall p Silentwall p Panels fitted vertically For the optimal installation it is essential that the wall (or the support and ventilation frame) is absolutely plumb. This will guarantee a perfect finishing to the internal corners and external edges of the room. Two-way joint cut at 45 45 p 1. Base profile (end or fold-away end profile). Prepare the base horizontal profi le by cutting it to the required length. Fix the base profi le to the wall (or the support frame) allowing a gap of at least 5 mm (3/16 in.) from fl oor level: this will enable ventilation of the cavity behind. When cladding particularly damp walls, it is necessary to leave a gap of at least 50 mm (1 15/16 in.) from fl oor level so as to protect the base of the panel from the risk of water being absorbed by the fl oor. Before tightening the fi xing screws, check that the profi le is absolutely horizontal. Should it not be, adjust the position by using a spirit level and then tighten the screws. p 2. Vertical starting profile (end or fold-away end profile, end profile for inside corners for corners - double end profile or small angle panel for edges). Prepare the vertical profi le by cutting it to the required length. Fix the starting end profi le to the wall (or the support frame). Before tightening the fi xing screws, check that the profi le is absolutely vertical. Should it not be, adjust the position and then tighten the screws. p 3. Top capping profile (end or fold-away end profile). Place the horizontal end profi le above the end of the panelling. Fix the profi le to the wall (or the support frame), and position and tighten the screws only suffi ciently to allow them to slide freely in the slotted holes. Two-way joint cut at 45 Head or end profile p 4. Panel. Prepare the fi rst Parqwall panel by cutting it to the required length and then slide it within the two installed guides. p 5. Joint between two panels (two-way joint or rack joint or fold-away joint). Prepare the fi rst Parqwall panel by cutting it to the required length and then slide it within the two installed guides. Fix the joint to the wall (or the support frame). Then position the next panel to engage the slot on the installed profi le. p 6. End profile for inside corners. When the Parqwall forms an inside angle, install the last panel on the wall, trimmed exactly to the size of the remaining wall, insert it in the end profi le for inside corners, leaving the surface with the slotted lots visible, then fi x it to the wall or to the support frame. Important: when installing Parqwall with visible aluminum joints, these must be cut at 45 angle, when they come together. p 7. Final panel. Position the last panel of each wall by trimming it across its width according to the maximum width allowed by the sliding of the end profi le. Position the profi le and tighten the screws only suffi ciently to allow them to slide freely in the slotted holes. Insert the panel into the guides and then fi x it into position by sliding the end profi le.

Illustration of profiles Parqwall p Silentwall p 30 Panels fitted horizontally For the optimal installation it is essential that the wall (or the support and ventilation frame) is absolutely plumb. This will guarantee a perfect finishing to the internal corners and external edges of the room. Two-way joint cut at 45 p 1. Base profile (end or fold-away end profile). Prepare the base horizontal profi le by cutting it to the required length. Fix the profi le to the wall (or the support frame) allowing a gap of at least 5 mm (3/16 in.) from fl oor level: this will enable ventilation of the cavity behind. When cladding particularly damp walls, it is necessary to leave a gap of at least 50 mm (1 15/16 in.) from fl oor level so as to protect the base of the panel from the risk of water being absorbed by the fl oor. Before tightening the fi xing screws, check that the profi le is absolutely horizontal. Should it not be, adjust the position by using a spirit level and then tighten the screws. p 2. Vertical starting profile (end or fold-away end profile, end profile for inside corners for corners - double end profile or small angle panel for edges). Prepare the vertical profi le by cutting it to the required length. Fix the starting end profi le to the wall (or the support frame). Before tightening the fi xing screws, check that the profi le is absolutely vertical. Should it not be, adjust the position and then tighten the screws. 45 p 3. Top capping profile (end or fold-away end profile). Place the end profi le above the end of the panelling. Fix the profi le to the wall (or the support frame), and position and tighten the screws only suffi ciently to allow them to slide freely in the slotted holes. Two-way joint cut at 45 Head or end profile p 4. Panel. Prepare the fi rst panel by cutting it to the required length and then slide it within the two installed guides. p 5. Joint between two panels (two-way joint or rack joint or fold-away joint). Prepare the joint by cutting it to the required length. Insert the joint in the installed panel slot in such a way that the surface with the slotted holes is visible. Fix the joint to the wall (or the support frame). Then position the next panel to engage the slot on the installed profi le. p 6. Head joint between two panels (two-way joint or fold-away joint). Prepare the joint by cutting it according to the width of the panel. Insert the joint in the installed panel slot in such a way that the surface with the slotted holes is visible. Important: when installing Parqwall with visible aluminum joints, these must be cut at 45 angle, when they come together. p 7. End profile for inside corners. When the Parqwall forms an inside angle, install the last panel on the wall, trimmed exactly to the size of the remaining wall, insert it in the end profi le for inside corners, leaving the surface with the slotted lots visible, then fi x it to the wall or to the support frame.

Parqwall Technical features Parqwall is the material suitable for cladding existing walls, whatever condition they may be in. It is resistant to wear, shock, dampness, fire, acids and light, that is to any surface affecting agents, both internal and external. The Parqwall cladding system has optimal resistance to fire. Parqwall is manufactured with materials which are completely resistant to any type of microorganisms and is therefore particularly suitable for cladding in hospitals, nurseries, schools and in all places where hygiene is of paramount importance. Although hard and durable, this material recreates the warmth typical of wood and other natural materials. It is also practical, antistatic and does not attract dust. All these features make it particularly suitable for spaces difficult to maintain, for example bars, restaurants, showrooms, doctors surgery rooms and large spaces in general. p Anti-vandalism. As already mentioned, Parqwall s unique characteristic is its extraordinary resistance to scratches, abrasion, shock, chemicals, ink and spray paints. Parqwall is coated on both sides with a high pressure HPL laminate. p Anti-stain. Parqwall is resistant to the most common types of stains (as laid down in the European Standard EN 438) and can be easily cleaned with water and ammonia and, if necessary, with organic solvents. p Resistance to dampness. The special installation technique and the physical and chemical characteristics of its components give the Parqwall panel surfaces their optimum water repellent qualities and resistance to dampness. p Sound proofing/insulating. Parqwall possesses inherent optimum sound proofi ng/insulating properties, but in order to obtain best performance it is advisable to insert another insulating material between the panels and the wall: glass fi bre, rock wool, etc. p Thermal insulation. Parqwall is a thermally insulating material. Its comfort characteristics help to retain heat and reduce heating costs. p Thermal transmittance. 0,0080 r = = 0,05 0,16 m2 h C Cal - 0,0080= thickness of material in linear meters - 0,16 = thermal conductivity p Reaction to fire. Euroclass: EN1350-1 C-s2, d0 Available on request the Parqwall FR (Euroclass: EN 1350-1 B-s2, d0) p Dimensions. The Parqwall panels are available in the following sizes: 400/600x2400 mm (15 11/16 or 23 9/16 in x 94 8/16 in.) (WxL) for the Printwood range, 400/600x3000 mm (15 11/16 or 23 9/16 in. x 118 2/16 in.) (WxL) for all other ranges. Panels can be installed either horizontally or vertically. The Parqwall panels are made of high-pressure plastic laminate (HPL) glued to a high density wood fi bre core (HDF = High-Density Fiberboard) of approx. 8 mm (5/16 in.) thickness. Each panel is provided with a longitudinal slot on all 4 sides to allow insertion of various profi les. p Joining. The joint between the panels and the wall is made by means of a simple anodized extruded aluminum profi le system. The profi les are provided with slotted holes at 500 mm (19 11/16 in.) intervals used to permit each section to be fi xed to the wall (or to the supporting and levelling frame behind) by means of screws. The slotted holes make it possible to adjust the level of the panelling and to lock it into position by sliding the end profi le, when this is used as a fi nishing element, both for horizontal and vertical installation.

Silentwall Technical features 32 The values measured show that Silentwall is ideal for absorbing medium to high frequencies, that is for offices, areas of high traffic, conference rooms and theatres. The above are obtained with the insertion of a 30 mm-thick (1 2/16 in.) polyester sheet insulation between the panel and the wall. Silentwall is a noise-reducing development of the modular Parqwall system. Silentwall is designed to absorb noises from highly-frequented rooms and with a high level of background disturbance. Noise reduction is the ability to dissipate acoustic energy, and is expressed as a coefficient (a) indicated with values between 0 (zero noise-reduction) and 1 (total noise reduction). p Test carried out on SILENTWALL as per UNI EN 20354/93 standard Test frequency Average values measured Reference scale (α) 100 < HZ > 315 Low frequency 0,28 0 < α < 0,3 Low noise-reduction 400 < HZ > 1250 Medium frequency 1600 < HZ > 5000 High frequency 0,73 0,6 < α < 1 High noise-reduction 0,41 0,3 < α < 0,6 Medium noise-reduction Front of panel dimensions in mm Back of panel dimensions in mm 4 24 24 4 24 Forum haul 5 mm 32 32 8 Dimensional Tolerance +/- 0,2 mm Panel Dimension: 600x3000 mm Dimensional Tolerance +/- 0,2 mm Panel Dimension: 600x3000 mm

Commercial data Parqwall p Silentwall p Commercial data Parqwall Range Colours and texture, Colours, Serie Cresp, Vertical Line, Decori Minimi, Fiber, Serie Milano, Legni, Serie Orientali, Serie Radiche, Serie Aceri, Printwood, Serigrafi a 2000 Digital Print Total thickness 8,3 ± 0,3 mm (5/16 in.) Weight Standard Packaging Kg/mq 8,2 (1.64 lbs per sq.ft.) 400/600 mm (15 11/16 or 23 9/16 in.) (width) 2400/3000 mm (94 8/16 or 118 2/16 in.) (length) panels on pallets Technical specification reference: panels produced from the section of a compound material consisting of an HDF wooden fi bre core with an external Print HPL laminate surface balanced with a Print HPL laminate. The panels are also milled along the sides creating a groove suitable for the insertion of the aluminium profi les making up the panel support structure to the wall. The profi les are of silver anodized aluminum and enable the installation of the panels both horizontally and vertically. These profi les can be visible or fold-away. Commercial data Parqwall FR Range Colours and texture, Colours, Serie Cresp, Vertical Line, Decori Minimi, Fiber, Serie Milano, Legni, Serie Orientali, Serie Radiche, Serie Aceri, Printwood, Serigrafi a 2000 Digital Print Total thickness 7,9 ± 0,3 mm Kg/mq 7,7 (1.57 lbs per sq.ft.) Weight Standard Packaging 400/600 mm (15 11/16 or 23 9/16 in.) (width) 2400/3000 mm (94 8/16 or 118 2/16 in.) (length) panels on pallets Technical specification reference: panels produced from the section of a compound material consisting of an HDF wooden fi bre core with an external Print HPL laminate surface balanced with a Print HPL laminate. The panels are also milled along the sides creating a groove suitable for the insertion of the aluminium profi les making up the panel support structure to the wall. The profi les are of silver anodized aluminum and enable the installation of the panels both horizontally and vertically. These profi les can be visible or fold-away. Commercial data Silentwall Range Colours and texture, Colours, Serie Cresp, Vertical Line, Decori Minimi, Fiber, Serie Milano, Legni, Serie Orientali, Serie Radiche, Serie Aceri, Printwood, Serigrafi a 2000 Digital Print Total thickness 7,9 ± 0,3 mm Kg/mq 6,5 (1.33 lbs per sq.ft.) Weight Standard Packaging 400/600 mm (15 11/16 or 23 9/16 in.) (width) 2400/3000 mm (94 8/16 or 118 2/16 in.) (length) panels on pallets Technical specification reference: panels produced from the section of a compound material consisting of an HDF wooden fi bre core with an external Print HPL laminate surface balanced with a Print HPL laminate. Noise reduction obtained by milling parallel to the short side on the back of the panel (pitch 4 and 16 mm) and parallel to the long side on the décor (pitch 3 and 21 mm). This will create a 20% surface perforation. The panels are also milled along the sides creating a groove suitable for the insertion of the aluminum profi les making up the panel support structure to the wall. The profi les are of silver anodized aluminum and enable the installation of the panels both horizontally and vertically. These profi les can be visible or foldaway. Commercial data Parqleather Range cod. 6249 Nero,cod. 6534 Testa di moro, cod. 6536 Avorio, cod. 6537 Panna, cod. 6538 Cappuccino, cod. 6622 Cuoio, cod. 6647 Sangue di bue Total thickness 7,3 mm Kg/mq 6,3 (1.29 lbs per sq.ft.) Weight Standard Packaging 400/600 mm (15 11/16 or 23 9/16 in.) (width) 3000 mm (118 2/16 in.) (length) panels on pallets Product specification: panels obtained by slicing a material consisting of a core of wood fi ber with a decorative leather surface (.4 mm thickness) and balanced with Spantex paper (.3 mm thickness). The panels are routed along the edges with a groove that permits the insertion of aluminum profi les that constitute the support of the panels to the wall. The profi les are silver anodized aluminum which allow the panels to be mounted either in a horizontal or vertical direction. These profi les can be either seen or hidden. Cleaning: for light colors, soap and water - for dark colors, soap and water - alcohol.

34 Technical data Parqwall p Silentwall p Technical data Parqwall Ecological E1 Test method Criteria and/or unit of measure Abrasion resistance Thickness swelling EN 438-2.6 EN 13329 Annex G Scratch resistance Resistenza all urto Stain resistance Colour resistance to xenon light Resistance to cigarette burns Surface electrical resistance Reaction to fire EN 438-2.14 EN 438-2.11 EN 438-2.15 EN 438-2.16 EN 438-2.18 NFPA 99 13501 Revs % (N) (N) Grade: groups 1 e 2 groups 3 e 4 Result IP- revs> 400 8,0 2,5 22 no alteration Grade Grade ohm Ω Category (class) > 6 > 4 no alteration The material is antistatic C-s2, d 0 Technical data Parqwall FR Ecological E1 Test method Criteria and/or unit of measure Abrasion resistance Thickness swelling EN 438-2.6 EN 13329 Annex G Scratch resistance Resistenza all urto Stain resistance Colour resistance to xenon light Resistance to cigarette burns Surface electrical resistance Reaction to fire EN 438-2.14 EN 438-2.11 EN 438-2.15 EN 438-2.16 EN 438-2.18 NFPA 99 13501 Revs % (N) (N) Grade: groups 1 e 2 groups 3 e 4 Result IP- revs> 400 8,0 2,5 22 no alteration Grade Grade ohm Ω Category (class) > 6 > 4 no alteration The material is antistatic B-s2, d 0 Technical data Silentwall Ecological E1 Test method Criteria and/or unit of measure Abrasion resistance Thickness swelling EN 438-2.6 EN 13329 Annex G Scratch resistance Resistenza all urto Stain resistance Colour resistance to xenon light Resistance to cigarette burns Surface electrical resistance Reaction to fire EN 438-2.14 EN 438-2.11 EN 438-2.15 EN 438-2.16 EN 438-2.18 NFPA 99 13501 Revs % (N) (N) Grade: groups 1 e 2 groups 3 e 4 Result IP- revs> 400 8,0 2,5 22 no alteration Grade Grade ohm Ω Category (class) > 6 > 4 no alteration The material is antistatic B-s2, d 0 Technical data Parqleather Abrasion resistance Surface electrical resistance Reaction to fire Test method UNI EN ISO 5470 UNI 76396 to be certifi ed Criteria and/or unit of measure cycles blue scale Result 1000 5

SALES ORGANIZATION IN ITALY p BARI - Modugno (Puglia e Basilicata) VACCA Alessandro - Cell. 335/8248877 SIT-IN BARI s.r.l. Centro distribuzione 70026 MODUGNO - Via delle Margherite n.c. Tel. 080/5314125 - Fax 080/5314124 p BOLOGNA - Calderara di Reno (Prov. BO, FE, MO) METTI Franco s.r.l. 40012 - Via Armaroli 45/A Tel. 051/722072-722455 - Fax 051/720247 p BOLZANO (Prov. BZ, TN) PLASTICOLOR s.a.s. di Nardelli Filippo & C. 39100 - Via Roma 69 - Tel. 0471/916188 - Fax 0471/507455 p CAGLIARI - Capoterra (Sardegna) VACCA Antonello 09012 - Via Platone 11 - Tel. 070/725642 - Fax 070/726170 p CATANIA - Piano Tavola (Prov. CT, ME, RG, SR) AGEN TEAM s.r.l. Rappresentanze - Roberto Chisari 95040 - C.da Rinaudo 17 (svincolo Valcorrente) Tel. 095/7132326 - Fax 095/391048 p CHIETI - Sambuceto (Abruzzo e Molise) FCF di Colarossi Barbara e C. s.a.s. 66020 Via Cavour 67 - Tel. 085/4460252 - Fax 085/4460252 p CUNEO - Grinzane Cavour (Alba) (Prov. CN, AT, AL) MILANESIO Giovanni 12060 - Via Borzone 4 - Tel. 0173/262558 - Fax 0173/231730 p FIRENZE - Sesto Fiorentino (Toscana, Umbria e Prov. SP) FILIALE ABET LAMINATI 50019 - Via del Cantone 66 - Tel. 055/316551 - Fax 055/318553 p GENOVA (Prov. GE) CO.RA.LL s.a.s. di RISSO Luca & C. 16132 - Via Donghi 71R - Tel. 010/505373 - Fax 010/502585 p MILANO - Cinisello Balsamo (Lombardia - escluso Prov. MN) (Piemonte solo Prov. NO) FILIALE ABET LAMINATI 20092 - Viale Brianza 6 - Tel. 02/6124851 - Fax 02/6170379 p PADOVA - Rubano (Prov. PD, VR, VI, RO) FILIALE ABET LAMINATI 35030 - Via Galvani 2 - Tel. 049/631777 - Fax 049/8975298 p PALERMO (Prov. PA, TP, EN, AG, CL) TECNORIV s.r.l. Rappresentanze 90124 - Via F. Pecoraino Z.I. Brancaccio Tel. 091/6216300 - Fax 091/582108 p PESARO - Villa S. Martino (Marche, San Marino e Prov. RA, FC, RN) FILIALE ABET LAMINATI 61100 - Via Toscana 91 - Tel. 0721/453405 - Fax 0721/453936 p REGGIO CALABRIA (Calabria) FERRANTE Giovanni 89123 - Via Sacchi 1 A - Tel. 0965/330550 - Fax 0965/330571 p REGGIO EMILIA - Cavriago (Prov. RE, PC, PR, MN) FILIALE ABET LAMINATI 42025 Loc. Corte Tegge - Via Bruno Buozzi 12 Tel. 0522/942434 - Fax 0522/942436 p ROMA (Lazio) FILIALE ABET LAMINATI 00133 Loc. Giardinetti - Via Stefano Della Bella 5/7 Tel. 06/2020074 - Fax 06/2040478 p SALERNO - Nocera Superiore (Campania) MARTORELLI Francesca 84015 - Via G. Matteotti 7 - Tel. 081/5144747 - Fax 081/5144746 p TORINO (Prov. TO, VC, BI, AO, SV, IM) FILIALE ABET LAMINATI 10155 - Via Cogne 42 - Tel. 011/266090 - Fax 011/202946 p TREVISO - Villorba (Prov. TV, VE, BL) PIVA s.r.l. 31050 - Via Roma 149 - Tel. 0422/914019 - Fax 0422/914064 p UDINE - Tavagnacco (Prov. UD, GO, PN, TS) RUMIZ F.LLI s.r.l. 33010 Via Nazionale 95 - Tel. 0432/572753 - Fax 0432/573233 WORDWILDE SALES ORGANIZATION p AUSTRALIAßABET PTY LIMITED - 11-13 Smoothy Place - Arndell Park NSW 2148 Phone 02/9672 7300 - Fax 02/9672 7303 www.abet.com.au - e-mail: info@abet.com.au ßABET Queensland - Unit 1, 59 Distribution Street Larapinta QLD 4110 PO BOX 4030 Forest Lake QLD 4078 Phone 07/3802 7988 - Fax 07/3802 7999 e-mail: info.qld@abet.com.au p BELGIUM - ABET N.V. - Streekbaan 244-1800 Vilvoorde Phone 02/4601910 - Fax 02/4603337 www.abet.be - e-mail: promotion-offi ce@abet.be p CANADA - ABET CORP. - 50 Paxman Road, Unit 10 - Toronto, ON M9C 1B7 Phone 416/6206556 - Fax 416/6205330 e-mail: abet@rogers.com p CHINA - ABET LAMINATI - Representative Offi ce - Unit c 17/F Hangdu Building - Huafu Road, Futian District - Shenzen 518031 Phone 0755/83790055-0056 - Fax 0755/83790213 e-mail: abetsz@public.szptt.net.cn p DENMARK - NORWAY - SWEDEN - ABET LAMINATI - Representative Offi ce - International House Center Boulevard - DK-2300 Kobenhavn S Phone 32/473167 - Fax 32/473166 www.abet.dk - e-mail: abet@abet-laminati.dk p FRANCE - ABET FRANCE Sarl - BP 9154-108, Avenue Aristide Bergès - Z.I. 73091 Chambery cedex 9 Phone 04/79621326 - Fax 04/79622044 www.print-france.fr - e-mail: stratifi es@abet-france.fr ABET FRANCE Sarl - Bureau Promotionnel - 12, rue d Armenonville - 92200 Neuilly-sur-Seine Phone 01/47452310 - Fax 01/40883781 e-mail: showroom@abet-france.fr p GERMANY - ABET GmbH - Füllenbruchstrasse 189-32051 Herford Phone 05221/3477-0 - Fax 05221/33196 www.abet.de - e-mail: info@abet.de p HOLLAND - ABET B.V. - Lagedijk Noord 4-3401 VA Ijsselstein Phone 030/6868450 - Fax 030/6888204 www.abet.nl - e-mail: verkoop@abet.nl p POLAND - ABET SP. z.o.o. - Ul. Sochaczewska 32-01-327 Warszawa Phone 022/6661040-6660585 - Fax 022/6660340 www.abetlaminaty.pl - e-mail: biuro@abetlaminaty.pl p RUSSIAN FEDERATION - Abet OOO Bol shaja Sadovaja 8 - Pod. 4 etazh 6 ofi s 649-651 - 123379 Moscow Phone 495/6501565 - Fax 495/6501515 e-mail: moscow@abet-laminati.ru p SPAINßABET LAMINATI S.A. - P.l. Can Gordi - Cal Catalá (Circuit de Montmeló) - C/Can Cabanyes, 59-08400 Granollers (Barcelona) Phone 93/5754197 - Fax 93/5754199 e-mail: barcelona@abetspain.com ßABET LAMINATI SA - Delegación del Norte - Poligono Industrial - Martiartu C/2 n. 59-48480 Arrigorriaga - Bizkaia Phone 94/4760931 - Fax 94/4763155 e-mail: bilbao@abetspain.com ßABET LAMINATI SA - Delegación Madrid - C/Lopez de Hoyos, 35-1a pl. - 28002 Madrid Phone 91/7459922 - Fax 91/7459999 e-mail: madrid@abetspain.com p SWITZERLAND - ABET AG - Oberfeld 9-6037 Root/Lu Phone 041/4556030 - Fax 041/4556033 www.abet.ch - e-mail: abet@abet.ch p UNITED KINGDOM - ABET LTD - 70, Roding Road - London Industrial Park - London E6 4LS Phone 020/74736910 - Fax 020/74766935 www.abetuk.com - e-mail: sales@abet.ltd.uk p U.S.A.ßABET INC. - 60 West Sheffi eld Avenue - Englewood, NJ 07631 Phone 201/5410700 - Fax 201/5410701 - Toll Free 800/2282238 www.abetlaminati.com - e-mail: usa@abetlaminati.com ßABET INC. - 3415 Regatta Blvd., Bldg. B, Richmond, CA 94804 Phone 510/4781011 - Fax 510/4781031 ßABET INC. - 4100 North Powerline Road, Suite S-3 - Pompano Beach, FL 33073 Phone 954/9355755 - Fax 954/9355711

www.pl-abetgroup.it

PL S.p.A. 22070 VERTEMATE (CO) ITALY Strada per Bulgorello, 3 Tel. +39.031.888.211 Fax +39.031.901.053 sales@pl-abetgroup.it Company with quality system as per UNI EN ISO 90001: 2000 cert. n 69 Graphic Design: Effige (MI) p Print: La Grafica Rampoldi