Hook modification study to reduce rockfish bycatch on circle hooks

Similar documents
Setline survey-based apportionment estimates

National Marine Fisheries Service Electronic Monitoring Cooperative Research and Implementation Program

Project Title: Fishing Technology and Conservation Engineering to Reduce Bycatch Contact: Carwyn F. Hammond and Scott McEntire

GATES, CATTLEGUARDS and PASSAGEWAYS. This factsheet looks at various options for allowing passage through fences for livestock, wildlife and people.

1000-LB. TRAILER JACK OWNER S MANUAL

NOAA Technical Memorandum NMFS-AFSC-152. by R. T. Ames, G. H. Williams, and S. M. Fitzgerald

It's large enough to handle most welding job shop projects, yet small enough to make it a worth while home-workshop tool

Times Microwave Systems Hermetically Sealed Assemblies

National Saltwater Recreational Fisheries Policy

Digital TV Coat Hanger Antenna

Vertical Break Parallel (VBP) / Vertical Break Slant (VBS)

Residential Garage Door Terminology

Includes specifications for: Surface Cleaning & Mounting Hardware.

Installation Guide for the TJ LCG PRO Suspension System (Low Center of Gravity) Available 4 or 5

STOCK LIST & BUYER S GUIDE

Wisconsin Building Products Evaluation

Report on. Wind Resistance of Signs supported by. Glass Fiber Reinforced Concrete (GFRC) Pillars

E-Line and Braided Line. E-Line Open Hole wireline

Ceiling Mounted Folding Attic Ladders Installation Instructions

PUMP JACK SYSTEM AND ACCESSORIES

Practical Alignment Tools and Techniques

Automatic Door Selection Guide

Lesson 6: Fisheries Management in the Open Ocean. Open Ocean

The entire document shall be read and understood before proceeding with a test. ISTA 3B Page 1 of 35

SIMULATION PRE-INSTALLATION GUIDELINES CONTRACTOR REQUIREMENTS FOR ROOM PREPARATION

Do-It-Yourself- Hydraulic Press Make Your Own, by Marshel Rossow

1. Lay out 2 pieces of 7/8" tubing and mark for bending as shown. Remember that the bend is in the shaded area as shown below in Figure 1.

Digital TV Coat Hanger Antenna

Oceanscience Cable Chimp II Cableway ROV System User Guide and Warranty

INSTALLATION AND OPERATING INSTRUCTIONS For Model GL1 Gate Locks

Fisheries of the Exclusive Economic Zone Off Alaska; Western Alaska Community. AGENCY: National Marine Fisheries Service (NMFS), National Oceanic and

Volkswagen B3 Passat Manual Transmission 02A 34 Manual Transmission - Controls, Assembly (Page GR-34) 02A 5-speed. Gearshift cable/lever installing

Pole Lathe and Shave Horse Design

-1- SPECIFICATIONS CONE SETTER PLATFORM ATTACHMENT INDEX

U.S./Canada Management and Special Access Programs for Sector Vessels

How To Collect Data From Angler Expenditure Data Collection

Chapter 5 FLOOR LOADING AND WEIGHTS

MODEL HSR-007 Direct Drive Rolling Steel

BUILDING MATERIALS, Wood, Laminated (Page 1 of 3) Viz.: Rafters; Arches; Beams; Joists; Timbers or Planks, structural or roof.

MESSENGERS FOR AERIAL CABLE

Precision Vise Combinations

IPHC oceanographic monitoring program 2013

Area is a measure of how much space is occupied by a figure. 1cm 1cm

Diameter. Swift Lift Round Recess Plug. Note: The diameter of the narrow recess plug is the same as the diameter of the round recess plug.

XPULT INSTRUCTIONS BASIC VERSION

Specifications for Lightning Protection. ASAE Engineering Practice

MAST ARMS & POLES. Ornamental Pole Top & Bases

Dock Hardware & Accessory Products Catalog

ROV shackles. your reliable partner

APE Pile Driving Course: Understanding Pile Driving Leads

758 Heavy-duty Ratchet Guy Wire Cutter

Manual for GlobePharma Mini-Press II Rotary Tablet Press

Accounting for and Managing All Pacific Halibut Removals

( ) A REV B system setup and deployment quick start guide

T&B Cable Tray. Metallic Aluminum. Straight Lengths. Tray Bottom Types Ladder, Ventilated and Solid Trough

Gate Leg Drop Leaf Table Plans

STEADYfast Stabilizer Installation Notes Fifth Wheel and Travel Trailers 11/23/13

THE IDEAL SOLUTION SHELVING. Sales Telephone: Sales Fax:

Nuffield and Middleweight Leyland Tractor - 11 inch - Double Clutch Overhaul Part 1 - Clutch Removal and Dismantling

Materials. Estimating Steel. Players. Materials. Shop Drawings. Detailing Process. Standard shapes. Fabricated members, Built-up sections

RPV - RP - RA air handling units

SECTION COILING COUNTER DOORS. Display hidden notes to specifier. (Don't know how? Click Here)

CABLE SUPPORT SYSTEMS

DUNGENESS CRAB REPORT

Carton - Straight Link Machine Chain (Order Unit is Feet )

Go-kart for little race-drivers

413 NOVA SYSTEM PAN AMERICAN TOOL CORPORATION 5990 NW PHONE (954) TOLL FREE FAX

SAMPLE TEST PAPER - I

LG G5 Chassis Brace Gen 5 Camaro THE MOST POWERFUL HEADERS ON THE PLANET Brought to you by LG Motorsports

Accessories for GF and RA machines

Sports and High Mast Lighting Poles Phone: (866) Fax: (817)

Ariva Powerful Marketing Displays. Exhibit & Display Solutions

Removal fishing to estimate catch probability: preliminary data analysis

This mount uses concrete parking bumpers and a Davis tripod to create a mounting solution for nonpenetrable

Rittal s Comprehensive Family Of... NETWORK RACK SOLUTIONS

SE05: Getting Started with Cognex DataMan Bar Code Readers - Hands On Lab Werner Solution Expo April 8 & 9

HARDWARE STANLEY ARCHITECTURAL HARDWARE

19 DYNAmax Free Standing Server C A B I N E T s

Pipe Cutting and Beveling Clamshells

Weight Measurement Technology

19 DYNAmax Free Standing Server C A B I N E T s

Hive Top Ventilation Shims

3M Mobile SkyWalk Series Horizontal Lifeline Product Return Form

Roof Curbs, Extensions and Equipment Supports

TECHNICAL INFORMATION

10 ft x 20 ft / 3 m x 6 m STEEL FRAME CAR CANOPY

Activity 2.3b Engineering Problem Solving Answer Key

Assembly Instructions for the InteliTrack 3000 Rail Tracking System

CATTURA TM DOWNDRAFT MODELS D49M30SB, D49M36SB, D49M48SB

Fall Protection System: A system put in place to protect workers from falling. (i.e. installation of guardrails, fall arrest, fall restraint, etc.

WARNING! Failure to follow these inspection procedures can cause personal injury and property damage.


Extra Tall Wide Span Gate

Flextray - Installation. Installation

HOW HYDRAULIC TRUCK CRANES WORK

SKT-SP Tangent Terminal

CHAPTER 11 UNIVERSITY OF FLORIDA

BODY-12, Door Handle - Removal, Installation, and Adjustment

DOUBLE DRUM TRACTION WINCH SYSTEMS FOR OCEANOGRAPHIC RESEARCH 1.0 TRACTION WINCH SYSTEM ADVANTAGES 11-2

GUIDELINES FOR UTILITY INSTALLATIONS Part 1 - Wire Lines and Communications Cables

Transcription:

Hook modification study to reduce rockfish bycatch on circle hooks Stephen M. Kaimmer and Stephen Wischniowski Abstract A pilot study was conducted to see if circle hooks could be modified to reduce rockfish bycatch. We attached spring wires across the gap of the hook, hypothesizing that fish with less aggressive hook attacks might not hook as readily due to the wires. Although previous camera work showed hesitant hook attacks by rockfish, this study encountered larger individuals, and their attacks were aggressive enough that they could easily bend the wires across the hook gaps to become hooked. Introduction Rockfish bycatch continues to be a problem in hook-and-line fisheries targeting Pacific halibut (Hippoglossus stenolepis). This is particularly so for yelloweye (Sebastes ruberrimus) and quillback rockfish (Sebastes maliger), which in some areas are under varying degrees of regulatory protection to reduce catches. Halibut hook attacks typically include taking the entire hook into the mouth. If the fish becomes hooked, this will occur as it attempts to swim away: the gangion and then the hook is pulled from the gullet, and as the hook curves around the corner of the jaw, the point catches in the cheek area from inside the mouth, and the fish is hooked. Previous camera observation of halibut and rockfish (Kaimmer 1998) suggested that hook attacks by halibut are much more forceful than those made by rockfish, and we hypothesized that spring wires across the hook gap might be able to reduce rockfish hooking while not impeding halibut captures. A spring wire affixed to the shank of the hook and spanning across to the point would flex during a forceful attack, allowing the hooking event to continue unimpeded. A less forceful hook attack would not cause the wire to flex, and the hook would be pulled from the mouth without hooking the fish. In order to test this hypothesis, the International Pacific Halibut Commission (IPHC) conducted a hook-modification experiment in southeastern Alaska in May 2012. Methods The 58-foot F/V Towego was chartered to deploy a drop camera to evaluate the effects of different wire configurations on the hooking success of circle hooks for halibut and rockfish. Hooks were modified to resemble weedless hooks sold to sports fishermen, with a short piece of spring wire attached to the hook shank near the eye so that it would lie across the gap of the hook (Figure 1). Different configurations of single and double stainless steel spring wires were tested in five different wire diameters: 0.032, 0.037, 0.039, 0.047, and 0.055 inch. All hook attacks were monitored and recorded. A light aluminum frame holding a GoPro Hero2 1 camera was focused on a single baited hook (Figure 2). The frame was made of 6061 aluminum stock with arms made from 5/16-inch-by-1.25-inch flat bar with 1-inch pipe welded to one edge for rigidity (Figure 2). The body of the frame was a piece of 3/8-inch-by-8-inch 1 www.gopro.com 487

aluminum plate cut to allow two 12-inch trawl floats to fit on aluminum rod pylons. A custom camera mount was constructed from stainless steel. The gear was weighted with a 4-foot long piece of 2.5-inch diameter round steel shaft weighing approximately 40 pounds, and the entire assembly weighed 23 pounds in water. The trawl floats each had a buoyancy of 22 pounds. The gear was deployed using an electric EZPull 2 pot hauler modified with a slip-ringed drum instead of a sheave. The drum contained 500 feet of Wireline 3 1-10-100A 1/10-inch cable for gear deployment. The Wireline provided an insulated inner core which allowed transmission of a live video signal from the camera to the surface. The GoPro camera was contained within a modified Sartek 4 SGP-DHSG deep housing, which allowed deployment at depths of over 500 feet. Modifications to the housing included lengthening to allow use of an extended battery back for the camera and addition of a bulkhead connection to allow the passage of video signals from the camera through the wireline cable to a surface TV monitor. Illumination was provided by two Sartek EBL1000D 1000 lumen LED flashlights mounted to the ends of the deployment frame arms. An oval cone of light 60 by 40 inches generated a usable field of view; rockfish were required to enter the bright field (the brighter lighted area that allowed for rockfish identification) of 40 by 30 inches before enumeration. Realtime video signals were sent up the Wireline cable, allowing precise control and evaluation of the gear sets. Because the length of cable was over 200 feet, an Intertek 5 ISL59605IRZ-EVALZ MegaQ signal equalizer was used to boost the signal definition. HDTV high definition 1080p (1920x1080 megapixel) video at 30 frames per second and a viewing angle of 170 degrees was captured on a 36-gigabyte flash card within the GoPro camera. All video was downloaded onto a laptop computer after each gear retrieval. All caught fish were carefully removed from the hook and released. Captured rockfish were repressurized using a SeaQualizer 6 pressure-activated release mechanism set to release the fish at 100 feet depth. The research design involved an iterative process, testing single and double wires of varying strengths. This was a pilot study, the see whether this type of hook modification would give any practical advantage in reducing rockfish bycatch through a reduction of hooking success. Results Fifty-two gear deployments were completed, with durations of time on bottom ranging from 35 to 135 minutes (Table 1 for a summary and Figure 3 for a chart of fishing locations). The gear was deployed in depths ranging from 20 to 65 fathoms. We observed 215 hook attacks by eleven species or species groups. We observed 201 attacks by our target groups of halibut (12 attacks), quillback rockfish (25 attacks) and yelloweye rockfish (164 attacks). We caught and released 4 halibut (33.3 percent total hooking success, among all hook treatments), 6 yelloweye rockfish (3.7 percent total hooking success), and no quillback rockfish (Tables 2 and 3). We observed no decrease in hooking success for yelloweye over 4.5 kg using various spring wire configurations. Too few quillback rockfish were encountered to make a definitive statement regarding this species. The fishermen on our charter boat commented that the wired hooks were very awkward to work with, both in baiting and in removing fish from the hook, and it would take a major improvement in bycatch avoidance to make these hooks feasible for use in a fishery. 2 EZ-Pull Products PO Box 1307, Shelton, Washington 98584 United States 3 RochesterWire and Cable,LLC, 9450 Clarewood, Houston, Texas 77036 United States 4 Sartek Industries, Inc 34 Jamaica Ave.,Port Jefferson Station, New York 11777 United States 5 Intersil 1001 Murphy Ranch Road, Milpitas, California, 05935 United States 6 SeaQualizer LLC, Miami, Florida, United States: theseaqualizer.com 488

Discussion In previous camera studies (Kaimmer 1998), an 8-percent hooking success was observed for 237 yelloweye rockfish hook attacks, and the average weight of the hooked fish in 1998 was 3.8 kg. We had hoped to decrease the hooking success for this species without affecting the catch of halibut. While the overall yelloweye hooking success in this current study was only 3.7 percent, all of the attacks by larger yelloweye resulted in captures. Yelloweye over about 20 inches and 4 kg, which constitute a large part of the yelloweye bycatch on setlines, took the hook and struggled violently, making our hook modification ineffective at keeping them off the hook. Twenty-five quillback attacks were observed with no captures. It is possible that the spring wires reduced the hooking success for this species, but the number of observations was too small to make a definitive statement. Bycatch mortality reduction measures currently in use include area avoidance and recompression of rockfish once caught. Hook modification as an additional measure to reduce bycatch mortality does not seem to be a fruitful avenue for future research. The similarity in hooking behavior between halibut and large yelloweye negates the likelihood of a hook modification that could be selective for one species over the other, although this would depend to some extent on the size of the yelloweye encountered. Acknowledgements We would like to thank Tor A. Bjorklund, an oceanographic equipment fabricator at the University of Washington, for his innovative design help in constructing our deployment frame, and Captain Leonard Leach of the F/V Towego for sharing his knowledge of fish behavior and distribution during the field portion of our project. References Kaimmer, S.M. 1998. Direct observations on the hooking behavior of Pacific halibut, Hippoglossus stenolepis. Fish. Bull. 97:873-883. 489

Table 1. Summary of fishing locations for the hook modification charter. Date Approximate location Description Depth range (fm) May 11-12 56-01N 132-53W North end of Clarence Strait 10-64 May 13 56-05N 132-43W North end of Clarence Strait 17-72 May 13 56-18N 132-59W Snow Pass 30 May 14-18 134-16W Eastside Coronation Island 17-55 May 18-19 55-57N 133-56W Warren Island 30-53 Table 2. Catch and catch disposition during 2012 hook modification charter. All catch was taken off Coronation Island; all weights were determined on a handheld digital scale. Date Set Location May 14 24 134-14W May 17 33 May 17 34 May 17 37 May 17 37 May 17 37 May 17 38 May 18 43 55-49N 134-57W May 18 47 55-49N 134-57W May 18 48 55-49N 134-57W Depth (fm) Species captured Length (in) Weight (lb) Disposition 30 Halibut 32 11 Careful release 32 Yelloweye 25 9.8 Recompress to 100 ft 32 Yelloweye 29 18 Recompress to 100 ft 32 Halibut 61 85 Careful release 31 Yelloweye 25 10 Recompress to 100 ft 35 Yelloweye 29 15 Recompress to 100 ft 37 Yelloweye 20 5 Recompress to 100 ft 33 Yelloweye 28 13 Recompress to 100 ft 31 Halibut 37 ~15 Careful release 31 Halibut 36 21 Careful release 490

Table 3. Hooking success for the target species: halibut, quillback and yelloweye rockfish. Yelloweye rockfish numbers are given for both small and large specimens. Weights for escaped fish are estimated from length estimates in camera image. Species Number of hook attacks Number caught Hooking success Halibut 12 4 33.3% Quillback (all under 2 kg) 25 0 0.0% Yelloweye (2-3 kg) 158 0 0.0% Yelloweye (4.5+ kg) 6 6 100.0% 491

Figure 1. Modified hook showing double and single wires across hook gap.

Figure 2. Camera deployment frame used in hook modification charter in southeastern Alaska during 2012.

Figure 3. Locations for hook modification charter in southeastern Alaska during 2012.