Hacking Brewhouse beer kits Questions? Email david.gummer@telus.net Brewhouse kits consist of a 15L bag of wort, a small package of sodium bicarbonate ph buffer, a yeast package and corn sugar. Although these kits are marketed to make basic versions of certain beer styles (e.g., blonde ale), great improvements and many style varieties can be accomplished by manipulating the original gravity, yeast, and water, or by adding hop pellets (dry-hopping) or wort from steeping specialty grains. For example, I have made 8 different styles from just the Munich dark lager kit: American brown ale, American amber ale, northern English brown ale, robust porter, dry stout, sweet stout, bock and dopplebock. Tips for hacking Brewhouse kits 1. Check out the Brewhouse beer kit technical specifications on http://www.thebrewhouse.com and identify a style that you would like to make according to the ingredients and specs. 2. When you go to buy your kit, check the date on the Brewhouse package. Try to buy packages that are stamped within 1-2 months prior. If they need to be kept longer, store them in a cool and dark place. 3. Throw-out the dry yeast package in the garbage. Obtain a good quality liquid yeast or dry yeast from your home brew store. These should be kept refrigerated until you are ready to use them. Again, they have date stamps and ideally they would be no more than 1-2 months old. Follow the instructions on the yeast package for activation. Choose yeast strains carefully knowing that this will have a major impact on the flavour and qualities of your beer. Refer to Wyeast strains available online: http://www.wyeastlab.com/hb_yeaststrain.cfm 4. Do not add as much water as the instructions indicate. I prefer to use reverse-osmosis water and I add only a small amount (e.g., 1-2 L) and then take a sample (using beer thief ) to measure the original gravity using a hydrometer. I dilute the wort with only enough water to get it into the correct range for the desired beer style. See BJCP style guidelines http://www.bjcp.org/2008styles/catdex.php 5. Don t forget the ph buffer! The wort in the bag is highly acidic so that it stays fresh and uninfected. I always add the ph buffer to the bottom of the carboy and then dissolve it in the first 1-2 L of reverseosmosis water before adding any wort or yeast to the carboy. 6. Before pouring the wort, wipe down the top of the Brewhouse box and spout and spray with Star-san (also available from local brewing store) or another sanitizer. Take care not to contaminate the top of the box or pour-spout from the wort-bag. 7. If you have difficulty with excessive foaming when you pour the wort into the carboy, try foam control drops which are available by mail order from http://morebeer.com/. I find that 8-10 drops of foam control into the first gallon or so of wort in the carboy helps minimize the foaming. This prevents a mess and risk of contamination. 8. Add lots of hop flavour and aroma by adding hop pellets to the carboy about 7-10 days before transferring to bottles or keg. Always use the freshest hops possible and keep them in air-tight containers in a deep freeze until you are ready to use them. 1
Hacking Brewhouse beer kits Questions? Email david.gummer@telus.net 9. When it comes time to bottle, don t automatically use all the corn sugar in the package. I have found that 1/3 to 1/2 cup is plenty to achieve appropriate carbonation of many British and American style ales. Do a little research online regarding carbonation levels and priming. 10. After you have hacked a couple Brewhouse kits by adjusting the original gravity, yeast, water and dry hopping, there are many more possibilities to explore like steeping specialty grains or boiling the wort and making hop additions. To start your batch of Brewhouse beer you will need Yeast (liquid yeast culture or specialty dry yeast) Brewhouse kit (wort and ph buffer) At least 4L of reverse-osmosis water 23L glass carboy Rubber bung and blow-off hose or air-lock Blow off hose or air-lock Large funnel Sanitizer (e.g., Star-san) Utility spray bottle for Star-san Optional (but recommended) Beer thief Beer hydrometer Hydrometer test tube American brown ale (aka Brown Rat ale ) Munich dark lager Brewhouse kit 4L of reverse osmosis water Wyeast 1028 London ale liquid yeast 42 g Styrian Goldings hop pellets for dry hopping last 7-10 days in fermenter American India pale ale (aka Prairie dog IPA ) India pale ale Brewhouse kit 4L of reverse-osmosis water Wyeast 1968 London ESB ale liquid yeast 21 g Cascade hop pellets for dry hopping last 7-10 days in fermenter 21 g Columbus hop pellets for dry hopping last 7-10 days in fermenter Extra special bitter (ESB) India pale ale Brewhouse kit 4L of reverse-osmosis water Wyeast 1968 London ESB ale liquid yeast 28 g East Kent Goldings hop pellets for dry hopping last 7-10 days in fermenter 2
Recipes for BrewHouse Beer Kits The BrewHouse website (http://www.thebrewhouse.com) has a great resource package for those interested in modifying the BrewHouse beer kits to make some very interesting beers. Complete instructions on how to modify the kits can be found here: http://thebrewhouse.com/resource_center/advanced_techniques.htm Some BrewHouse award-winning recipes can also be found here: http://thebrewhouse.com/resource_center/the_inner.htm Below are some interesting recipes that you might try. American IPA Ingredients: 1 Brew House IPA kit 1 oz American hops (such as Cascade or Centennial) American yeast (such as Wyeast 1056 American Ale or Safale US-O5 dry yeast) Add 2 to 4 litres of water (not the full 8 L that the kit recommends) to adjust the gravity of the beer to be slightly higher than what the kit recommends. Dry hop in the secondary with the American hops for about 10 days before bottling or kegging. English Special Bitter Ingredients: 1 Brew House IPA kit 3/4 lb medium crystal malt (crushed) 1 oz East Kent Goldings hops British yeast (such as Wyeast 1028 London Ale or Wyeast 1968 London ESB) 1. Heat 3 5 litres of water to 160 F (71 C) in a large pot. 2. Place crystal malt in a loosely tied grain bag (or paint strainer bag), and submerge in the water for 30 mins, stirring every 10 mins or so. 3. Remove grain bag from pot and cool in an ice bath to room temperature (or cooler). 4. Combine liquid wort from the pot with the wort in the Brewhouse kit inside the fermenter, and pitch yeast as normal. 5. Dry hop in the secondary with the American hops for about 10 days before bottling or kegging.
English Brown Ale Ingredients: 1 Brew House Cream Ale kit 1/2 lb medium crystal malt (crushed) 1/4 lb chocolate malt (crushed) British yeast (such as Wyeast 1028 London Ale or Wyeast 1968 London ESB or Nottingham dry yeast) 1. Heat 4 6 litres of water to 160 F (71 C) in a large pot. 2. Place crystal and chocolate malt in a loosely tied grain bag (or paint strainer bag), and submerge in the water for 30 mins, stirring every 10 mins or so. 3. Remove grain bag from pot and cool in an ice bath to room temperature (or cooler). 4. Combine liquid wort from the pot with the wort in the Brewhouse kit inside the fermenter, and pitch yeast as normal. Brew House Irish Stout (From the Brew House website) Ingredients for 5 gallons: 1 Brew House Munich Dark Lager kit 12 oz. roast barley 8 oz. flaked barley 1 oz. Northern Brewer hops Wyeast 1084 Irish ale yeast Optional ingredients: 8 oz. quick oats 12 oz. lactose 1. Crack your roast barley and place it, with the flaked barley, in a grain bag. If you wish to make an oatmeal stout (Samuel Smith), include the quick oats. 2. Add grain bag to 2 gallons of cold water in a 3 gallon (or larger) pot. Place over medium heat. Bring temperature to 170 F and hold for 20 minutes, stirring the grain bag occasionally. 3. Remove and discard grains, add the Northern Brewer hops, and boil for 20 minutes. If you want to make a milk stout (Mackeson's), dissolve lactose in the liquid during the last 5 minutes of the boil. 4. Remove pot from heat, cool, and use the liquid to make up the 5 gallon volume of the kit. Top up with water if necessary. Do not forget to add the ph adjustment package (package #1). 5. Pitch your yeast culture and ferment at 60 70 F. Initially, this stout will have a very sharp, grainy, roasty taste, quite coffee-like. With 6 weeks of aging, it will take on a mellow, smooth, luscious character, with the bitterness of the grains integrating with the maltiness of the dark lager base. The crispness of the Northern Brewer hops will unite it all, and suddenly the voice of Saint Brigid will ring in your ears: "I dream of Heaven, with a great lake of beer...."
Waltzing Wiener Wanderjhar Wogger (Vienna Lager) (From the Brew House website) Ingredients for 5 gallons: 1 Brew House Pilsner kit 1 lb. Munich malt 8 oz. aromatic malt 8 oz. CaraVienne malt 1 oz. Saaz hops Wyeast 2124 Bohemian lager yeast 1. Crack your grains and place them in a grain bag. 2. Add grain bag to 2 gallons of cold water in a 3 gallon (or larger) pot. Place over medium heat. Bring temperature to 170 F and hold for 20 minutes, stirring the grain bag occasionally. 3. Remove and discard grains and boil for 20 minutes. At the end of the boil, add Saaz hops, remove pot from heat and steep hops for 5 minutes. 4. Cool the liquid and use it to make up the volume of the kit. Top up with water if necessary. Do not forget to add the ph adjustment package. 5. Pitch your yeast culture and ferment at 46 54 F. Lager at 32 F for 6 to 8 weeks. Dupe-All Golden Ale (Belgian Strong Golden Ale) (From the Brew House website) Ingredients for 4 gallons: 1 Brew House American Premium Lager kit 1 lb. CaraPils malt 1 lb. white table sugar or corn sugar 1 oz. Kent Goldings hops 1 oz. Saaz hops Wyeast 1388 Belgian strong ale yeast 1. Crack your grain and place it in a grain bag. 2. Place the grain bag in a 3 gallon (or larger) pot with 1 gallon of cold water and 1 gallon of wort from the kit. Place over medium heat. Bring temperature to 170 F and hold for 20 minutes, stirring the grain bag occasionally. 3. Remove and discard grain, add Kent Goldings hops and sugar, and boil for 20 minutes. Remove pot from heat, add Saaz hops and steep for a further 5 minutes. 4. Cool the liquid and use it to make up the 4 gallon volume. Top up with water if necessary. Do not forget to add the ph adjustment package. 5. Pitch your yeast culture and ferment at 65 75 F. This beer will require long aging (at least three months in the bottle) before it develops the smooth, delicate fruitiness and complexity that are the hallmarks of Duvel.