INDUSTRIAL DOORS TORVERK S RANGE WITH THE MOST ENERGY EFFICIENT DOOR SYSTEM IN EUROPE
Doors are like cars A door that is cheap to buy, or a door that is cheap to own What do you prefer? Doors are like cars. The car with the lowest price tag might not be the cheapest to own. An industrial doors is usually characterised as a product that can have high after sales costs. The difference between choosing the right or wrong type of door can be a question of thousands of pounds per door and year. These are costs for energy, repairs and spare parts, and also include environmental costs through unnecessary road transports due to service requirements and the door s short life span. However, and this is our point, high after sales costs can be avoided. If you choose the right door. At Torverk, we have used the Swedish Academy of Engineering Sciences an the Transport Research Commission s calculation model for Utilization cost calculation for doors for a long time. Throughout decades we have listened to our customers, analysed needs and calculated after sales costs to be able to choose the right technical solution. With our long experience and knowledge we would love to analyse your needs to calculate which type of door is right for you. Both from an economic and environmental point of view. INDUSTRIAL DOORS 2005
Q-DOOR FX Original Europas energisnålaste standardport
Q-DOOR FX Original The most energy efficient standard door in Europe Compared to almost any other type of door, Q-DOOR FX is cheaper to own. It uses less energy, has lower service- and spare part costs, and is subject to less collision damage due to its movement pattern. All around construction The folding door is the most all around door type due to its simplicity, small space demands and its ease of use in the upright position. But above all, due to the possibilities in adapting the design of the folding door in size, number of sections, window configuration, appearance etc. Q-DOOR FX is built up by 1-16 sections depending on your door opening size. Q-DOOR FX with motor operator is built up by 2-4 sections. The door is made out or in going, with or without motor operator or prepared for motor operator. Door leaf for tough environments Torverk and Q-DOOR FX are pioneers when it comes to safety. We were first with a pinch guard in 1963, and at the turn of the millennium we were first again - this time with the entire door as a pinch guard. Optimal quality, low service level and long life span demands good dimensions. That is why Q-DOOR FX has a wind load dimension of 0.7-2.0 kpa. Integrated, heavy-duty steel reinforce- ment and 52 kg density/m3 freon-free polyurethane foam makes the leaf the most sturdy and resilient in its class. Up-value for Q-DOOR FX is as low as 0.22. Standard colours Standard colours below. Colour number and name are our terms, nearest NCS-standard in brackets. As colours can be misleading in print, please contact us for exact colour samples. Silver metallic Colour nr 271 (RAL: 9006) Green Colour nr 298 (S6020-G30Y) Brown red Colour nr 293 (S5040-Y90R) Grey (off-white) Colour nr 222 (S2005-G90Y) Brown Colour nr 284 (S8005-Y80R) Red Colour nr 13-04 (S1580-Y90R) Clear blue Colour nr 12-04 (S3060-R90B) Blue Colour nr 296 (S6030-B) Stainless steel SS 2348
Special sealing system Q-DOOR s sealings are custom designed and heavy sized. Thanks to the vulcanized trippel chamber sealings between sections and in all corners, you achieve maximum sealing effect. Windows for light and design The window frame made in aluminium has a broken cold-bridge and double insulated glass to achieve a minimum of energy loss, and to assure the windows looks just as good after years of usage. In addition, you will not have to deal with problems like condensation or dirt between the panes. Standard window sizes: 300x500, 500x500, 300x1200 or 500x1200 mm WxH. Standard Breast Height 1450 mm (window height 500 mm) and 750 mm (window height 1200 mm). Custom sizes on demand. Maximum glass area per door section = 30%. Pass door When needed, Q-DOOR FX can be provided with a pass door. The pass door height aesthetically adjusts to all standard window sizes and can be provided with different kinds of locking device, door handles and windows. Secure locking and mounting Q-DOOR FX is delivered with a espagnolet locking (for padlock) able to open from the inside. The door can also be provided with Security Door Lock with door handle on the inside, or both in and outside. Both alternatives matches the Swedish insurance companies locking demands for industries. Q-DOOR FX with motor operator is locked with non reversable selflocking motor. The doors can also be provided with espagnolet and Security Door Lock like standard Q-DOOR FX. Torverk s mountings are well dimensioned, have low friction and simple management. The frame mountings have a smooth and shiny, hardened steel ball that carries the whole door weight. Lasting motor operators with long guarantees Q-DOOR FX with motor operator is manufactured with two, three or four sections. Standard Q-DOOR FX can be prepared for motor operators. Torverk s motor operators requires a minimum of service and depending on service agreements, have guarantees on 2, 5 or 10 years. The most energy efficient standard door in Europe
Range of TORVERK This brochure gives just a glance of our products and our procedures. We know the importance of making an early choice of door in the building process. We also believe that those who will use, and in the end pay to use the door, have their say. Regardless of whether you will own the door yourself, or whether you are the one answering for the construction work, we have just the model for you. Both with regards to funtionality and your wallet. Naturally we prefer to sell top quality, as it is more economic in the long run, but we also provide budget priced doors if your project is sensitive to price. We have a complete range of doors. This means we are not governed by our own range, and thereby not forced to suggest a specific type of door. We can help you choose the one solution that best meets your requirements. Range - all types Q-DOOR FX Original - sandwich designed bifolding door (prev. page) R-DOOR FX - frame based folding door OH-DOOR - overhead sectional door QSL - sandwich designed panel door RSL - frame based panel door RSD - frame based panel door Q-DOOR SX - sandwich designed side sliding door R-DOOR SX - frame based side sliding door T-GATE - bifolding gate Q-DOC - cargo sheds, loading bays and weather seals Q-PANEL Door operators Motor operators
R-DOOR FX - frame based folding door R-DOOR FX is one of the market s most dependable frame based doors. This robust and hard wearing door is well suited for tough environments, special sizes or when large glazed areas are required. It is less suitable for outer walls in normally heated premises, due to its high U-value. OH-DOOR - overhead sectional door The overhead sectional door has small requirements on floor- and side space. The principle of an up going, spring balanced section is simple and makes the door easy to open and shut. OH-DOOR is known for high quality, optimal isolation and operation safety. The door is provided in various designs to satisfy different desires. We deliver the Overhead sectional door with or without motor operators. Panel doors The function of the panel door is much like an ordinary but big door. This door is suitable for small and medium sized openings for person and/or vehicle passages. The sandwich designed panel door is perfect when you are looking for a well isolated door. Sliding doors The sandwich designed sliding door Q-DOOR SX has a well isolated door sections. It is well suited for storages, stock rooms, hangars and similar environments. In smaller sizes Q-DOOR SX is also used where small and fast doors are desired. If you choose this sandwich designed sliding door you get a robust and dependable construction for tough environments. Gates T-GATE can be delivered as folding, panel or sliding gate, with or without motor operator. Q-DOC Q-DOC is our dependable system for cargo sheds, loading bays, weather seal. Other If you would like to know more about the door types presented here, and some more, take a look at our separate broschures, or call us on +46 560 68 98 00. You will also find useful information on our webbsite: www.torverk.com
Torverk in the true light of day We keep our promises by doing it right the first time Our promise to you Up until the installation everything has been a lot of promises an colourful dreams. But it is in the true light of day we want to show our strength. Construction ideas, sales promises, time schedules and so on, are all promises that now are about to become reality. No one is perfect, but it can be a goal. We introduced our quality system ISO 9001 back in 1992, today we are certified according to ISO 9001:2000, and from fall 2005 also environment certified according to ISO 14001. No errors during the final inspection mean time and cost savings for you, as for us. Our quality promise is straight and simple - we keep our promises by doing it right the first time. But of course it is not all down to our fitters. Our organisation is trimmed to make a thorough work from the ground up. And we begin on the analysis phase. Then it is easy to do a good job from construction to installation. Our fitters have the pleasure of putting the icing on the cake.
Economy and environment Torverk s started in 1949. And since 1962, Torverk has run its own industrial door production in Torsby, Sweden. It is said, that experience replaces nothing. But in our branch, we know that neither does nothing replace experience. Door experts say there are three aspects that have the greatest impact on the environment - energy loss during usage, road transports due to servicing and short product life span. It is now your choice. Whether your door will require a lot or a little of service and lot or a little energy during its short or long life span. Frequently it is a question of whether you wish to buy a cheap door, or to have a door that is cheap to own. Study the figure below and you will soon find that economy and the environment go hand in hand when it concerns doors. Our task is to make doors that are cheap to own, but at the same time to contribute towards a better environment.
Good door economy The foundations of good door economy are laid long before you choose the actual door. It is very common to first choose which type of door you want, and then just hunt down the lowest price. This method can unfortunately turn out to be extremely expensive in the long run. Also for the environment. A door in a building incurs costs over and above its purchasing price. The utilization cost comprises all the costs that directly or indirectly affect the choice of door. The difference between right or wrong choice can be a question of thousands of pounds per door and year in utilization costs. With high traffic doors, a question of tens of thousands per year. And door. If you want, we can help, based on your needs, to analyse what is just right for you - which factors give good door economy in your circumstances. What are utilization costs? Below illustrates the costs for a normal industrial door. The direct costs (the lower block) are easy to calculate with a large degree of certainty. To assess the indirect costs (upper block) you will need both experience and industrial door expertise. Direct costs Capital costs Passage costs Heat loss costs Indirect costs Operating costs Maintenance costs Service costs Repair costs Spare part costs Inspection costs Surface costs Downtime costs Surface costs Downtime costs Maintenance costs Repair costs Operating costs Heat loss costs closed door Heat loss costs open door Capital costs Passage costs
TORVERK Industrial Doors Production: Lina.S, www.linas.se On our webb site, www.torverk.se you will find lots of useful information. Both about industrial doors and utilization costs. If you have any questions, you are always welcome to contact us. TORVERK Industrial Doors AB, Box 184, S-685 24 Torsby, Sweden Tel. 0560-68 98 00 Fax. 0560-122 65 info@torverk.se www.torverk.se