Int Dip Unit IC - Element IC1 - August 2012 NEBOSH Diploma in Occupational Health and Safety Licence details RMS Publishing Victoria House, Lower High Street, Stourbridge DY8 1TA RMS Publishing. Second Edition August 2012. All rights reserved. No part of this presentation may be stored in a retrieval system, reproduced, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise without either the prior written permission of the Publishers. This presentation may not be lent, resold, hired out or otherwise disposed of by way of trade in any form other than that in which it is published, without the prior consent of the Publishers. This presentation may not be reproduced in any form without prior consent of the Publishers other than a single copy thumbnail handout for immediate use by the tutor. Whilst every effort is made to ensure the completeness and accuracy of the information contained herein, ACT can bear no liability for any omission or error. Issued to: Single Licence Licence No: INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 1 INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 2 NEBOSH Diploma in Occupational Health and Safety Unit IC Workplace and Work Equipment Safety INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 3 INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 4 Learning outcomes Element IC1 General workplace issues Explain the need for, and factors involved in, the provision and maintenance of a safe working environment, with specific reference to access and egress, pedestrians, and slips, trips and falls Explain how safety signs are used in the workplace Explain the assessment of risk and safe working practices associated with work in confined spaces Outline the main issues associated with maintaining structural safety of workplaces Explain the hazards, risks and controls when working at heights Explain the hazards, risks and controls for lone working INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 5 INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 6 Sample of PowerPoint presentation for NEBOSH Diploma in Occupational Health and Safety 1
Int Dip Unit IC - Element IC1 - August 2012 Contents Contents Safety signs Confined spaces Structural safety of workplaces Working at height Lone working Safety signs Confined spaces Structural safety of workplaces Working at height Lone working INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 7 INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 8 Safe means of access and egress Wet coefficient of friction (CoF), slip resistant testing of footwear and surfaces Safe places of work and safe means of access and egress It is the duty of the employer to ensure a safe place of work When meeting this duty of care it is necessary to consider where the worker is located For example, standing in a warehouse conducting a stock take, in a sewer or on a scaffold, each has features that may present a hazard and would require control For example, the stocktaking area may have to be cordoned off to ensure fork lift trucks do not collide with the worker and the scaffold platform must be capable of taking the worker s weight and be wide enough for the work being done INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 9 INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 10 Practical considerations When determining practical considerations, it is necessary to take regard to where the worker is located They may be standing in a warehouse determining the quantity of stock, in a sewer or on a scaffold, and each has features that may present a hazard and would require control Practical considerations Other practical considerations in the provision and maintenance of a safe place of work include: - Provision of good ventilation - Reasonable temperatures - Suitable and sufficient lighting - Cleanliness and dealing with waste - Adequate space - Suitable workstations and seating - Condition of floors - Establishing traffic routes INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 11 INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 12 Sample of PowerPoint presentation for NEBOSH Diploma in Occupational Health and Safety 2
Int Dip Unit IC - Element IC1 - August 2012 Safe means of access and egress Important to take regard of such matters as: - Clearly marked gangways - Walk routes that are free from obstruction - The maintenance of floors and staircases and the organisation of traffic routes (including pedestrian traffic) A critical consideration when establishing traffic systems is the safety interface between pedestrians and traffic The routes that people use should be clearly defined and marked Safe means of access and egress When determining access and egress, account should be made of those with a disability and care should be taken to ensure that the workplace, including doors, passageways, stairs and access to showers, washbasins, lavatories and workstations are suitable for disabled persons As with the provision of a safe place of work, it is essential to make arrangements to ensure means of access and egress are maintained INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 13 INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 14 Slip resistant surfaces should be provided: At the entrance of buildings On designated walkways On changes of level On ramps or slopes Where walkways intersect with internal transport routes In work areas where spills of liquids or dry contaminants are likely Where liquids are decanted or containers filled or stored On access areas used for inspection or maintenance Locations where workers need to go that are exposed to the weather INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 15 When designing and selecting a slip resistant surface consider: The consequences of slipping The type of contamination likely Ability to control contamination Level of use of the surface The range of people using the surface What people might be doing on the surface Environmental issues Level of control over footwear used The surface option The slip resistance rating INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 16 Slip resistance surface on steps Anti-slip flooring INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 17 Source: RMS. INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 18 Source: RMS. Sample of PowerPoint presentation for NEBOSH Diploma in Occupational Health and Safety 3
Int Dip Unit IC - Element IC1 - August 2012 Coefficient of friction (COF) A number which represents the friction between two surfaces The symbol usually used is μ μ = R where μ is the coefficient of friction and R is the F normal reaction force and F is the friction force The frictional force, F, will act parallel to the surfaces in contact and in a direction to oppose the motion that is taking/ trying to take place The coefficient of friction is dependent on both the surface of the material and that of the material sliding over it Slip resistant testing of surfaces and footwear The method of testing the slip resistance of surfaces and footwear is based on the use of two instruments - A pendulum coefficient of friction test - A surface micro roughness meter INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 19 INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 20 Pendulum coefficient of friction tester Roughness measuring instrument INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 21 Source: HSE/HSL. INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 22 Source: Taylor Hobson. Slip resistant testing of surfaces and footwear In the UK, the HSE has developed a web based slip assessment tool to assist with the evaluation of slipperiness of floor surfaces This can be used to guide the measurement and analysis of resistance measurements The roughness factor can be used to guide the selection of materials for the surface of work and walk surfaces select a material with a high roughness for situations where contaminants are likely to reduce the coefficient of friction The roughness of the surface must be balanced with the need for and ability to clean the surface INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 23 Slip assessment tool INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 24 Source: HSE. Sample of PowerPoint presentation for NEBOSH Diploma in Occupational Health and Safety 4
Int Dip Unit IC - Element IC1 - August 2012 Different coefficient of friction between one surface and another Varies depending on the two materials involved, due to the two characteristic components of friction (see table) The higher the coefficient of friction the more resistance to slip there is between the two surfaces Material 1 Material 2 Asphalt (Dry) Asphalt (Wet) Concrete (Dry) Concrete (Wet) µ 0.5-0.8 0.25-0.75 0.6-0.85 0.45-0.75 Source: Roy Beardmore. Effects of contamination on surfaces in terms of COF The presence of a contaminant on a surface can greatly influence the coefficient of friction The manner in which it affects it is very dependent upon factors such as the contact pressure, the size and shape of the contact area, the velocity of movement and the viscosity of the liquid Makes the measurement of μ in wet conditions much more complex Dry contaminants, such as dust and powders can also affect the coefficient of friction INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 25 INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 26 Hydrodynamic effect INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 27 Source: CIRIA. Methods for cleaning floors and the appropriate footwear to wear whilst cleaning Cleaning of floors allows the: - Removal of surface dirt and contaminant - Original slip resistance of the surface to be restored - Removal of microbial soiling Methods for cleaning floors include vacuum dust removal, washing, drying, sealing and polishing. Cleaning arrangements should be in place to deal with the routine removal of low level natural contamination and higher level process derived contamination INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 28 Methods for cleaning floors and the appropriate footwear to wear whilst cleaning Wet cleaning The cleaner should wear suitable footwear Sweep the floor and ensure equipment is clean Prevent people from walking on wet smooth floors until they are totally dry Close area, use barriers, clean in sections, as last resort use cones Warn those affected wet cleaning in progress Use the right balance of cleaning solution to water INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 29 Part only of the complete Element IC1 - General workplace issues INT DIP Unit IC 2nd Edition - Element IC1 - v.1.0 - Slide 30 Sample of PowerPoint presentation for NEBOSH Diploma in Occupational Health and Safety 5