ANGLES Data and Specifications 01 Aluminum Angles (Typically Rounded Corners) This is the most versatile of the heat treatable aluminum alloys. This alloy offers a wide range of mechanical properties and corrosion resistance. It is easily fabricated and has good formability. Applications: Screw machine parts, structural components, truck bodies and frames. Alclad 01 is used where appearance and better corrosion resistance with good strength are required. Analysis: Cu -.1/.0 Si -.0/.80 Fe -.70 Max. Mn -.1 Max. Mg -.80/1. Zn -. Max. Cr -.0/. Ti -.1 Max. Mechanical Properties: (T-T1 bare) Tensile Strength (psi),000 Yield Point (psi) 0,000 Elongation (in for 1 dia.) 17 Brinell Hardness 9 Machinability: Rated between 70% and 80% of 011 in the T and T conditions, and 0% in the T and T conditions. Weldability: All methods including furnace brazing. Forming: In T condition, fairly severe forming operations may be accomplished. Heat Treating: Treatable. 0 T Aluminum Angles (Typically Square Corners) This grade is commonly referred to as the architectural alloy. Developed as an extrusion alloy with relatively high tensile properties, excellent finish characteristics and high corrosion resistance. Applications: Moldings and extruded trim for stores and homes both interior and exterior. Used extensively for anodized parts. Analysis: Cu -.10 Max. Si -.0/.0 Fe -. Max. Mn -.10 Max. Mg -./.90 Zn -.10 Max. Cr -.10 Max. Ti -.10 Max. Mechanical Properties: (T) Tensile Strength (psi) 7,000 Yield Point (psi) 1,000 Elongation (in for 1 dia.) 1 Brinell Hardness 0 Machinability: For automatic screw machine operations rated between 7% and 8% of 011 in the T condition. It is 0% of 011 in the O condition, and 0% in the T condition. One stop shopping for any metal, cut and ready, fast! 1 8 87 9 metalsupermarkets.com 1
BEAM/CHANNELS Data and Specifications 01 Aluminum Beams This is the most versatile of the heat treatable aluminum alloys. This alloy offers a wide range of mechanical properties and corrosion resistance. It is easily fabricated and has good formability. Applications: Screw machine parts, structural components, truck bodies and frames. Alclad 01 is used where appearance and better corrosion resistance with good strength are required. Analysis: Cu -.1/.0 Si -.0/.80 Fe -.70 Max. Mn -.1 Max. Mg -.80/1. Zn -. Max. Cr -.0/. Ti -.1 Max. Mechanical Properties: (T-T1 bare) Tensile Strength (psi),000 Yield Point (psi) 0,000 Elongation (in for 1 dia.) 17 Brinell Hardness 9 Machinability: Rated between 70% and 80% of 011 in the T and T conditions, and 0% in the T and T conditions. Weldability: All methods including furnace brazing. Forming: In T condition, fairly severe forming operations may be accomplished. Heat Treating: Treatable. 01 Aluminum Channels This is the most versatile of the heat treatable aluminum alloys. This alloy offers a wide range of mechanical properties and corrosion resistance. It is easily fabricated and has good formability. Applications: Screw machine parts, structural components, truck bodies and frames. Alclad 01 is used where appearance and better corrosion resistance with good strength are required. Analysis: Cu -.1/.0 Si -.0/.80 Fe -.70 Max. Mn -.1 Max. Mg -.80/1. Zn -. Max. Cr -.0/. Ti -.1 Max. Mechanical Properties: (T-T1 bare) Tensile Strength (psi),000 Yield Point (psi) 0,000 Elongation (in for 1 dia.) 17 Brinell Hardness 9 Machinability: Rated between 70% and 80% of 011 in the T and T conditions, and 0% in the T and T conditions. Weldability: All methods including furnace brazing. Forming: In T condition, fairly severe forming operations may be accomplished. Heat Treating: Treatable. Order only what you need. 1 8 87 9 metalsupermarkets.com
PLATE Data and Specifications 0 T Aluminum Channels This grade is commonly referred to as the architectural alloy. Developed as an extrusion alloy with relatively high tensile properties, excellent finish characteristics and high corrosion resistance. Applications: Moldings and extruded trim for stores and homes both interior and exterior. Used extensively for anodized parts. Analysis: Cu -.10 Max. Si -.0/.0 Fe -. Max. Mn -.10 Max. Mg -./.90 Zn -.10 Max. Cr -.10 Max. Ti -.10 Max. Mechanical Properties: (T) Tensile Strength (psi) 7,000 Yield Point (psi) 1,000 Elongation (in for 1 dia.) 1 Brinell Hardness 0 Machinability: For automatic screw machine operations rated between 7% and 8% of 011 in the T condition. It is 0% of 011 in the O condition, and 0% in the T condition. 0-T1 Aluminum Plate This is one of the best known of high strength aluminum alloys. With excellent strength and fatigue resistance it is used to advantage on structures and parts where a good strength-to-weight ratio is desired. It can be subsequently hardened by artificial aging. Applications: Aircraft structural components and parts for the transportation industry. Analysis: Cu -.80/.90 Si -.0 Max. Fe -.0 Max. Mn -.0/.90 Max. Mg - 1.0/1.80 Max Zn -. Cr -.10 Max. Ti -.1 Max. Other-.1 Max. A1-remainder Mechanical Properties: (typical): Tensile Strength (psi) 8,000 Yield Point (psi) 7,000 Elongation (% in ) 0 Brinell Hardness 10 Machinability: Good. Weldability: May be spot, seam, or flash welded. Arc or Gas is not recommended. Annealing: Can be softened to O temper by thermal treatment. Forming: It is recommended that any forming be performed after being fully annealed. Corrosion Resistance: Relatively poor but to improve corrosion resistance parts should be anodized or clad. We source hard to find metals. If you don t see what you re looking for, Call! 1 8 87 9 metalsupermarkets.com
PLATE Data and Specifications 01-T1 Wrought Aluminum Plate This is the most versatile of the heat treatable aluminum alloys. It offers good mechanical properties and excellent corrosion resistance and can be fabricated by many of the commonly used techniques. Applications: Wide variety of applications from tooling to truck frames and bodies and various structural components. Analysis: Cu -.1/.0 Max. Si -.0/.80 Max. Fe -.70 Max. Mn -.1 Max. Mg -.80/1.0 Max. Zn -. Max. Cr -.0/. Ti -.1 Max. Other -.1 Max. A1 - Remainder Mechanical Properties: (typical) Tensile Strength (psi),000 Yield Point (psi) 0,000 Elongation (% in ) 1 Brinell Hardness 9 Machinability: Fair. Weldability: Excellent. Annealing: Can be softened to O temper by thermal treatment. Hardening: Can be hardened by artificial aging thermal treatment processes. Forming: Good by most forming methods. 707-T1 Wrought Aluminum Plate This is one of the highest strength aluminum alloys available. Its strength-to-weight ratio is excellent. It is ideally suited for highly stressed aircraft parts. Applications: Used mostly in aircraft and transportation industries where strength is critical. Has been used as mold material in the plastics industry. Analysis: Cu - 1.0/.0 Max. Si -.0 Max. Fe -.0 Max. Mn -.0 Max. Mg -.10/.90 Max Zn -.10/.10 Max. Cr -.18/.8 Ti -.0 Max. Other -.1 Max. A1 - Remainder Mechanical Properties: (typical): Tensile Strength (psi) 8,000 Yield Point (psi) 7,000 Elongation (% in ) 11 Brinell Hardness 10 Machinability: Good. Weldability: Spot and seam welding can be used. Arc and gas not recommended. Annealing: Can be softened to O temper by thermal treatment. Hardening: Can be hardened by artificial aging thermal treatment processes. Forming: May be formed in the annealed condition and subsequently hardened by artificial aging. Corrosion Resistance: Average but may be improved by cladding parts. We ll load your order or deliver your order to you. 1 8 87 9 metalsupermarkets.com
TREAD PLATE Data and Specifications 01 - T Aluminum Tread Plate Used in aluminum structural applications where strength and skid resistance is critical. Produced at the mill with a raised diamond pattern on the surface for skid resistance. Applications: Running boards, steps, floors, walkways, platforms, cover plates, trench covers, truck runways. Analysis: Cu -.1/.0 Max. Si -.0/.80 Max. Fe -.70 Max. Mn -.1 Max. Mg -.80/1.0 Max Zn -. Max. Cr -.0/. Ti -.1 Max. Other -.1 Max. A1 - Remainder Mechanical Properties: (typical) Tensile Strength (psi),000 Yield Point (psi) 0,000 Elongation (% in ) 1 Brinell Hardness 9 Machinability: Fair. Weldability: Excellent. Forming: Good by most forming methods. 00 Bright Tread Aluminum Plate This is the highest strength alloy of the more common non-heat-treatable grades. Fatigue strength is higher than most aluminum alloys. Particularly good resistance to marine atmosphere and salt water corrosion. Excellent workability. It may be drawn or formed into intricate shapes and its slightly greater strength in the annealed condition minimizes tearing that occurs in 1100 or 00. Excellent finishing characteristics with bright, clear anodic coatings. Applications: Wide variety from aircraft components to home appliances, marine and transportation industry parts, heavy duty cooking utensils, and equipment for bulk processing food. Analysis: Cu -.10 Max. Si -. Max. Fe -.0 Max. Mn -.10 Max. Mg -.0/.80 Max. Zn -.10 Cr -.1/. Mechanical Properties: (typical): Tensile Strength (psi),000 Yield Point (psi) 8,000 Elongation (in for.0 sheet) 1 Weldability: Yes. Forming: Yes. 08 - H Mill Finish Tread Plate Sister alloy to 08 with comparable characteristics (excellent corrosion resistance, weldability, and high strength) but slightly less strength. Applications: Primarily for marine applications. Weldability: Weldable with high strength. Corrosion Resistance: High. Forming: Yes. 1 8 87 9 metalsupermarkets.com
ROD & BAR Data and Specifications 011 T Aluminum (Rod & Bar) (Free Machining Screw Stock) The most free machining of the common aluminum alloys with excellent mechanical properties. It is widely used for automatic screw machine products in parts requiring extensive machining. It may be machined at high speeds with relatively heavy feeds. Its corrosion resistance is good with excellent hardness and strength. Applications: High speed automatic screw machine parts. Analysis: and under: Cu -.0/.0 Si - 0. Max. Fe - 0.7 Max. Zn - 0. Max. Bi - 0./0. Pb - 0./0. Mechanical Properties: Tensile Strength (psi),000 Yield Point (psi),000 Elongation (in 1 Round) 1 Brinell Hardness 9 Machineability: 100%. Weldability: Resistance. Surface Cutting Speed: 10 ft/min. 0 T/T1 Aluminum (Rod & Bar) One of the best known of high strength aluminum alloys. With its high strength and excellent fatigue resistance it is used to advantage on structures and parts where a good strength-to-weight ratio is desired. 0 in the annealed condition is easily formed and may be subsequently heat treated. Since corrosion resistance is relatively low, 0 is commonly used with an anodized finish or in clad form (Alclad) with a thin surface layer of high purity aluminum. Applications: Aircraft fittings, structural components, hardware, truck wheels and parts for the transportation industry. Analysis: Cu -.80/.90 Si -.0 Max. Fe -.0 Max. Mn -.0/.90 Mg - 1.0/1.80 Zn -. Max. Cr -.10 Max. Ti -.1 Max. Mechanical Properties: (T-T1 bare) Tensile Strength (psi) 8,000 Yield Point (psi) 7,000 Elongation (in for 1 dia.) 19 Brinell Hardness 10 Machinability: 90% for T condition. Machines to high finish. Weldability: Spot, seam or flash welded. Arc and gas welding not recommended. Forming: Easily formed in the annealed condition. Heat Treating: Treatable. what you want, when you want the way you want. At Metal Supermarkets, we stock a wide variety of ferrous, non-ferrous, and specialty products in a wide variety of shapes (bar, tube, channel, angle, sheet and plate, perforated sheet). If you don t see what you re looking for, Call! 1 8 87 9 metalsupermarkets.com
ROD & BAR Data and Specifications 01 T/T1 Aluminum (Rod & Bar) This is the most versatile of the heat treatable aluminum alloys. This alloy offers a wide range of mechanical properties and corrosion resistance. It is easily fabricated and has good formability. Applications: Screw machine parts, structural components, truck bodies and frames. Alclad 01 is used where appearance and better corrosion resistance with good strength are required. Analysis: Cu -.1/.0 Si -.0/.80 Fe -.70 Max. Mn -.1 Max. Mg -.80/1. Zn -. Max. Cr -.0/. Ti -.1 Max. Mechanical Properties: (T-T1 bare) Tensile Strength (psi),000 Yield Point (psi) 0,000 Elongation (in for 1 dia.) 17 Brinell Hardness 9 Machinability: Rated between 70% and 80% of 011 in the T and T conditions, and 0% in the ) condition. Weldability: All methods including furnace brazing. Forming: In T condition, fairly severe forming operations may be accomplished. Heat Treating: Treatable. 707 T1 Aluminum (Rod & Bar) This is one of the highest strength aluminum alloys available. This material has high strength-to-weight ratio and is used for highly stressed parts. Applications: Used where highest strength is needed. Analysis: Cu - 1.0/.00 Si -.0 Max. Fe -.0 Max. Mn -.0 Max. Mg -.10/.90 Zn -.10/.10 Cr -.18/.8 Ti -.0 Max. Mechanical Properties: (T-T1 bare) Tensile Strength (psi) 8,000 Yield Point (psi) 7,000 Elongation (in for 1 dia.) 11 Brinell Hardness 10 Machinability: For automatic screw machine operations rated between 7% and 8% of 011 in the T condition, and % in the O condition. Weldability: Spot or flash welded, arc and gas welding not recommended. Forming: Easily formed in the annealed condition. Heat Treating: Treatable. One stop shopping for any metal, cut and ready, fast! 1 8 87 9 metalsupermarkets.com 7
SHEET Data and Specifications 1100-H1 Aluminum Sheet This grade is commercially pure aluminum. It is soft and ductile with excellent workability. Ideal for applications involving intricate forming because it work-hardens more slowly than other alloys. It has the highest thermal conductivity of any aluminum alloy and its electrical conductivity is second only to the electrical conductor grade. Applications: Kitchenware, giftware, decorative trim, intricate formed parts, chemical and food processing industries. Analysis: Cu -.0/.0 Si + Fe -.9 Max. Mn -.0 Max. Zn -.10 Max. Mechanical Properties: (typical) Tensile Strength (psi) 18,000 Yield Point (psi) 17,000 Elongation (in for.0 sheet) 9 Weldability: Yes. Forming: Yes. Heat Treatable: No. Corrosion Resistance: Excellent. 00-H1 Aluminum Sheet This is the most widely used of all aluminum alloys. It is essentially commercially pure aluminum with the addition of Manganese which increases strength some 0% over 1100. With excellent corrosion resistance and workability it can be deep drawn or spun, welded or brazed. Applications: Cooking utensils, kitchen equipment, decorative trim, awnings, siding, storage tanks, chemical equipment. Analysis: Cu -.0 Max. Si -.0 Max. Fe -.70 Zn -.10 Mechanical Properties: (typical): Tensile Strength (psi),000 Yield Point (psi) 1,000 Elongation (in for.0 sheet) 8 Weldability: Yes. Forming: Yes. Heat Treatable: No. I needed one hundred pieces of aluminum cut in pieces by the end of the day. Metal Supermarkets delivered the entire order by :00. 8 1 8 87 9 metalsupermarkets.com
SHEET Data and Specifications 0-H Aluminum Sheet This is the highest strength alloy of the more common non-heat-treatable grades. Fatigue strength is higher than most aluminum alloys. Particularly good resistance to marine atmosphere and salt water corrosion. Excellent workability. It may be drawn or formed into intricate shapes and its slightly greater strength in the annealed condition minimizes tearing that occurs in 1100 or 00. Excellent finishing characteristics with bright, clear anodic coatings. Applications: Wide variety from aircraft components to home appliances, marine and transportation industry parts, heavy duty cooking utensils, and equipment for bulk processing food. Analysis: Cu -.10 Max. Si -. Max. Fe -.0 Max. Mn -.10 Max. Mg -.0/.80 Max. Zn -.10 Cr -.1/. Mechanical Properties: (typical) Tensile Strength (psi),000 Yield Point (psi) 8,000 Elongation (in for.0 sheet) 1 Weldability: Yes. Forming: Yes. 01 Aluminum Sheet This is the most versatile of the heat treatable aluminum alloys. It has most of the good qualities of aluminum and offers a wide range of mechanical properties and corrosion resistance. It can be fabricated by many of the commonly used techniques. In the annealed condition it has good formability. In the T condition, fairly severe forming operations may be accomplished. The T properties may be obtained by artificial aging. Applications: Used for a wide variety of products and applications from truck bodies and frames to screw machine parts and structural components. Alclad 01 is used where appearance and better corrosion resistance with good strength are required. Analysis: Cu -.1/.0 Si -.0/.80 Fe -.70 Max. Mn -.1 Max. Mg -.80/1. Zn -. Max. Cr -.0/. Ti -.1 Max. Mechanical Properties: T Bare T Bare Alclad T Alclad T Tensile Strength (psi),000,000,000,000 Yield Point (psi) 1,000 0,000 19,000 7,000 Machinability: Rated between 70% and 80% of 011 in the T and T conditions, and 0% in the T and T conditions. Weldability: All methods including furnace brazing. Heat Treating: Treatable. We source hard to find metals. If you don t see what you re looking for, Call! 1 8 87 9 metalsupermarkets.com 9
TUBES Data and Specifications 0 Drawn and Extruded Aluminum Tubes This grade is similar to 01 except that it has slightly lesser strength. Commonly referred to as an architectural alloy, it is the best suited alloy for anodizing applications including hard coat anodizing for air cylinder tube. Applications: Construction tube, lawn furniture, luggage racks, air cylinders. Analysis: Cu -.10 Max. Si -.0/.0 Fe -. Max. Mn -.10 Max. Mg -./.90 Zn -.10 Max. Cr -.10 Max. Ti -.10 Max. Mechanical Properties: (typical) Tensile Strength (psi),000 Yield Point (psi) 1,000 Elongation (% in ) 1 Machinability: Fair. Weldability: Excellent. Any metal, Cut and Ready, Fast! With locations across the United States and Canada, fast turnaround time for delivery and orders processed while you wait, you know you can have your order when you want it. With production cutting, shearing on-site and aluminum plate cutting in the quantity and size you need, your order is always the way you want it. If you don t see what you re looking for, Call! 0 1 8 87 9 metalsupermarkets.com
ANGLES 01 - T EXTRUDED ALUMINUM ANGLES EQUAL LEG / X / X 1/8 1 X 1 X 1/8 1 X 1 X /1 1 X 1 X 1/ 1-1/ X 1-1/ X 1/8 1-1/ X 1-1/ X /1 1-1/ X 1-1/ X 1/ 1-1/ X 1-1/ X 1/8 1-1/ X 1-1/ X /1 1-1/ X 1-1/ X 1/ 1-/ X 1-/ X 1/8 1-/ X 1-/ X /1 1-/ X 1-/ X 1/ X X 1/8 X X /1 X X 1/ X X /1 X X /8-1/ X -1/ X /1-1/ X -1/ X 1/ -1/ X -1/ X /1-1/ X -1/ X /8.01.7.00.1..10...19.809.97.71.9.77.80 1.110 1. 1.0 1.070 1.0 1.79.07 X X /1 X X 1/ X X /1 X X /8 X X 1/ -1/ X -1/ X 1/ -1/ X -1/ X /8-1/ X -1/ X 1/ X X 1/ X X /8 X X 1/ X X /8 X X 1/ X X /8 X X 1/ X X /8 X X / 8 X 8 X 1/ 8 X 8 X /8 8 X 8 X / 8 X 8 X 1 1.7 1.8.08.7.7 1.989.9.8.8..1.7.78.119.7 8. 9.91 9.11 11.8 1.78 17.7 01 - T EXTRUDED ALUMINUM ANGLES UNEQUAL LEG 1 X / X 1/8 1-1/ X 1 X 1/ 1-1/ X 1-1/ X /1 1-1/ X 1-1/ X 1/ X 1 X /1 X 1-1/ X 1/8 X 1-1/ X /1 X 1-1/ X 1/ X 1-1/ X /8-1/ X 1-1/ X 1/8-1/ X 1-1/ X /1-1/ X 1-1/ X 1/ -1/ X X /1-1/ X X 1/ X X /1 X X 1/.8..8.71.1.9.79.9 1.79..80 1.10.9 1.8 1.08 1.99 X X /8 X X 1/ X -1/ X 1/ X -1/ X /8-1/ X -1/ X /1-1/ X -1/ X 1/ -1/ X -1/ X /8 X X 1/ X X /8 X X /8 X X 1/ X X /8 X X /8 X X 1/ 8 X X /8 8 X X /.0. 1.7.8 1.8 1.8.7 1.988.9.9.9.78.7.78 9.8 11.79 1 8 87 9 metalsupermarkets.com 1
ANGLES 0 - T ALUMINUM ANGLES EQUAL LEG 1/ X 1/ X 1/1 1/ X 1/ X 1/8 /8 X /8 X 1/8 / X / X 1/1 / X / X 1/8 1 X 1 X 1/1 1 X 1 X 1/8 1 X 1 X /1 1-1/ X 1-1/ X 1/8 1-1/ X 1-1/ X /1.09.18.1.10.0.11.7.01.9.11 1-1/ X 1-1/ X 1/8 1-1/ X 1-1/ X /1 1-1/ X 1-1/ X 1/ X X 1/8 X X /1 X X 1/ -1/ X -1/ X 1/8 X X /1 X X 1/...808.9.8 1.10.7 1.7 1.8 0 - T ALUMINUM ANGLES UNEQUAL LEG 1 X 1/ X 1/8 1 X / X 1/8 1-1/ X 1/ X 1/8 1-1/ X / X 1/8 1-1/ X 1 X 1/8 X 1 X 1/8 X 1-1/ X 1/8-1/ X 1 X 1/8-1/ X 1-1/ X 1/8-1/ X X 1/8.0.9.9.9..9.9.9. X 1 X 1/8 X X 1/8 X X 1/ X X /8 X X 1/8 X X 1/ X X 1/8 X X 1/8 X X 1/8.9.71 1.97.09.8 1.91 1.010 1.17 1.0 There is no upside to down time Wide variety of metals in rod, bar, sheet, plate, structural, tube & pipe. Stores coast-to-coast No minimums Same day delivery or pickup One stop shopping for any metal, cut and ready, fast! 1 8 87 9 metalsupermarkets.com
I-BEAMS 01 - T EXTRUDED I-BEAM AMERICAN STANDARD T A T1 B A B T1 T Lbs/Ft..000.0.170.170 1.9.000.09.9.170.99.000.00.190.190..000.79..190.81.000.000.10.10..000.17.7.10..000.8.9.10.10.000.0.0.0.0.000...0.10.000...0.9 7.000.7..0.0 8.000.000.70.70.0 8.000...70 8.808 9.000.0.90.90 7.0 10.000.0.10.10 8.71 10.000.797.7.10 10.7 1.000.000.0.0 10.99 1.000.078.8.0 1.089 1.000.0.0.0 1.077 1.000...0 1.8 1.000.77.87.0 17.87 01 - T EXTRUDED I-BEAM ALUMINUM ASSOCIATION T A T1 B A B T1 T Lbs/Ft..000.00.10.00 1.7.000.00.10.0.00.000.000.10.0.11.000.000.170.90.79.000.00.190.0.700.000.000.190.90.00.000.000.10.0.9 7.000.00.0.80.799 8.000.000.0.0.181 8.000.000.0.10 7.0 9.000.00.70.0 8.1 10.000.000.0.10 8.7 10.000.000.90.00 10.8 1.000 7.000.90.70 11.71 1.000 7.000.10.0 1.9 1 8 87 9 metalsupermarkets.com
CHANNELS 01 - T EXTRUDED CHANNELS AMERICAN STANDARD A B T1 T Lbs/Ft..00 1.10.170.170 1.17.00 1.98.8.170 1.79.00 1.9..170.07.00 1.80.180.180 1.8.00 1.7.7.180.11.00 1.70.0.180.0.00 1.70.190.190.1.00 1.88..190.108.00 1.90.00.00.8.00 1.9..00.00.00.0.1.00.1.00.17.7.00.98 7.00.110.0.10.1 8.00.90.0.0. 8.00.7.88.0.8 9.00.8.8.0.911 10.00.00.0.0.78 10.00.88..0 8.1 1.00.90.00.80 7.11 1.00.07.87.80 8.9 1.00.170.10.80 10.7 01 - T EXTRUDED CHANNELS ALUMINUM ASSOCIATION t AA A B T1 T Lbs/Ft..00 1.000.10.10.7.00 1.0.170.0 1.071.00 1.00.10.00 1.1.00 1.70.170.0 1.97.00.000.10.0 1.78.00.0.190.90.1.00.0.10.0.1.00.00.170.90.8.00.0.10.0.00 8.00.000.190.0.17 9.00.0.0.0.98 9.00.000.90.0.970 10.00.00.0.10.1 10.00.0.10.00 8.0 1.00.000.90.70 8.7 1.00.000.0.0 11.8 B B T- T- A T-1 T-1 A 1 8 87 9 metalsupermarkets.com
CHANNELS A B C 1/ X /8 X 1/8 1/ X 1/ X / 1/ X / X 1/8 /8 X /8 X 1/8 / X /8 X 1/8 / X / X 1/8 1 X 1/ X 1/8 1 X 1 X 1/8 1-1/8 X 1/ X 1/8 1-1/ X 1-1/ X 1/8 1-1/ X 1/ X 1/8 1-1/ X 1 X 1/8 0 - T EXTRUDED ALUMINUM CHANNELS C (Typically Sharp Corners) QQA 00/9 and ASTM B1 A.17.1.8.9.18.9.8.0.9.1.0.7 A B C 1-/ X / X 1/8 1-/ X 1 X 1/8 X 1/ X 1/8 X 1 X 1/8 X X 1/8 X X 1/8-1/ X 7/8 X 1/8-1/ X 1-1/ X 1/8 X 1/ X 1/8 X 1 X 1/8 X 1-1/ X /1 X X /1.1.1.0..8 1...771..99 1. 1.90 B The art of metal work We ll go to great lengths to help you find the perfect metal for your masterpiece. Wide variety of metals in bar, sheet, plate, structural, tube & pipe Stores coast-to-coast No minimums Same day delivery or pickup 1 8 87 9 metalsupermarkets.com
HEXAGONS /1 1/ 1/ /1 /8 / 7/1 1/ 9/1 /8 11/1 / 011 - T ALUMINUM HEXAGONS.07.08.0.10.18.1.0...1.81.9 1/1 7/8 1/1 1 1-1/8 1-/1 1-1/ 1-/8 1-1/ 1-/.71.810.89 1.07 1.8 1.90 1.1 1.998.78.11. /8 11/1 / 1/1 7/8 1/1 1 1-1/8 0 - T1 ALUMINUM HEXAGONS.0.90.8.8.79.910 1.07 1.1 1-1/ 1-/8 1-1/ 1-/8 1-/ 1-7/8-1/ 1.19 1.90..70.178.8.11.8 1/ /8 1/ /8 / 1 01 - T ALUMINUM HEXAGONS.0.1..97.7 1.018 1-1/8 1-1/ 1-/8 1-1/ 1-/ 1.89 1.91 1.9.91.119.07 what you want, when you want the way you want. 1 8 87 9 metalsupermarkets.com
SEAMLESS PIPE 01 - T and 0-T SEAMLESS PIPE EXTRUDED Nom. Sched. O.D./In. Wall/In. I.D./In. Wt./Ft Alloy Alloy 01 0 1/8 0.0.08.9.08 X 1/ 0.0.088..17 X /8 0.7.091.9.19 X 1/ 0.80.109..9 X 1/ 80.80.17..7 X / 0 1.00.11.8.91 X / 80 1.00.1.7.10 X 1 0 1.1.1 1.09.81 X X 1 80 1.1.179.97.71 X 1-1/ 10 1.0.109 1.. X 1-1/ 0 1.0.10 1.80.78 X X 1-1/ 80 1.0.191 1.78 1.07 X 1-1/ 10 1.900.109 1.8.71 X 1-1/ 0 1.900.1 1.10.90 X X 1-1/ 80 1.900.00 1.00 1. X.7.0.. X 10.7.109.17.91 X 0.7.1.07 1. X X 80.7.18 1.99 1.77 X X -1/ 10.87.10. 1.1 X -1/ 0.87.0.9.00 X X -1/ 80.87.7..0 X.00.08. 1.07 X 10.00.10.0 1.98 X 0.00.1.08.1 X X 80.00.00.900.7 X -1/ 0.000..8.11 X -1/ 80.000.18.. X.00.08. 1. X 10.00.10.0 1.9 X X 0.00.7.0.7 X X 80.00.7.8.18 X 10..1.9.88 X 0..8.07.07 X X 80..7.81 7.188 X 10..1.7.1 X 0..80.0. X X 80...71 9.88 X 8 10 8..18 8.9. X 8 0 8.. 7.981 9.878 X X 8 80 8..00 7. 1.010 X 10 0 10.70. 10.00 1.00 X X 1 STD 1.70.7 1.000 17.1 X 1 80 1.70.88 11.7 0.0 X 1 8 87 9 metalsupermarkets.com 7
PLATE 0 - T1 ALUMINUM PLATE MILL FINISH - HEAT TREATABLE Thickness Width Length Lbs/ Lbs/ (Inches) (In) (In) Sq/Ft Plate.0 X 9.00 88.00.0 8 X 1.00 17.10.1 8 X 1.10 19.90.7 8 X 1.00.810.00 X 1 7.00.800.00 8 X 1 7.00 0.10. 8 X 1 9.000 8.00.70 8 X 1 10.800.0.87 X 9 1.00 08.00 1.000 8 X 1 1.00 700.80 1.0 8 X 1 18.000 87.00 1.00 8 X 1 1.00 101.0 1.70 8 X 1.00 1.0.000 8 X 1 8.800 101.0.00 8 X 1.000 17.00.000 8 X 1.00 10.70.00 8 X 1 0.00.890.000 8 X 1 7.00 80.00.00 8 X 1.800 1.710.000 8 X 1 7.000 0.10.000 8 X 1 8.00 0.90 01 - T1 ALUMINUM PLATE MILL FINISH - HEAT TREATABLE Thickness Width Length Lbs/ Lbs/ (Inches) (In) (In) Sq/Ft Plate 1/ X 9.0 89.0 8 X 9.0 118.90 8 X 1.0 178.90 0 X 10.0 18.90 0 X 1.0.00 7 X 1.0.70 9 X 0.0 8.00 /1 X 9.0 110.0 8 X 1.0 19.980 9 X 0.0 7.00 /8 X 9.0 1.00 8 X 1.0.70 0 X 1.0 0.0 7 X 1.0 9.770 9 X 0.0 870.00 1/ X 9 7.0 177.0 8 X 1 7.0.80 0 X 1 7.0 0.10 8 1 8 87 9 metalsupermarkets.com
PLATE 01 - T1 ALUMINUM PLATE MILL FINISH - HEAT TREATABLE Thickness Width Length Lbs/ Lbs/ (Inches) (In) (In) Sq/Ft Plate 1/ 7 X 1 7.0.000 /8 X 9 9.00 1.80 8 X 1 9.00 8.990 0 X 10 9.00.0 / X 9 10.80.0 8 X 1 10.80 7.70 0 X 1 10.80 8.100 7 X 0 10.80 19.00 7 X 1 10.80 79.710 7/8 8 X 1 1.0 10.790 1 X 9 1.0.00 8 X 1 1.0 70.770 0 X 1 1.0 87.0 1-1/ 8 X 1 17.90 87.080 1-1/ X 9 1.90.0 8 X 1 1.90 10.880 0 X 1 1.90 10.0 1-/ X 9.070 1.10 8 X 1.070 10.10 8 X 1 8.0 19.80 0 X 1 8.0 178.70 7 X 1 8.0 08.10 8 X 1 8.0 17.0 0 X 1 8.0 171.0-1/ 8 X 1.10 1.70-1/ 8 X 1.800 17.0 8 X 1.80 08.0 0 X 1.80 01.0-1/ 8 X 1 0.090 7.800 8 X 1 7.0 791.0 0 X 1 7.0 8.0-1/ 8 X 1.10 1.0 8 X 1 71.70 78.0-1/ 8 X 1 77.0 777.0 8 X 1 8.80 1.00 7 8 X 1 98.70 80.99 8 8 X 1 11.900 9.18 9 8 X 1 19.00 08.0 10 8 X 1 11.100 87.7 1 8 X 1 19.00 80. Also available in 1100, 00, 0, 08, 08, etc. 1 8 87 9 metalsupermarkets.com 9
PLATE/TREAD 707 - T1 ALUMINUM PLATE MILL FINISH - HEAT TREATABLE Thickness Width Length Lbs/ Lbs/ (Inches) (In) (In) Sq/Ft Plate 0.0 8 X 1. 17.9 0.7 8 X 1.. 0.00 8 X 1 7.9.9 0. 8 X 1 9.090.0 0.70 8 X 1 10.91 0.97 1.000 8 X 1 1. 707. 1.0 8 X 1 18.18 88.79 1.00 8 X 1 1.8 101.9 1.70 8 X 1. 18.1.000 8 X 1 9.09 11.7.0 8 X 1.7 19.9.00 8 X 1. 179.8.000 8 X 1. 1.0.000 8 X 1 8.18 81..000 8 X 1 7.7 9.17.000 8 X 1 87..80 8.000 8 X 1 11.0 1.1 08 - H ALUMINUM MILL FINISH TREAD PLATE Thickness Width Length Lbs/ Lbs/ (Inches) (In) (In) Sq/Ft Plate 8 X 19 1.8 117.1 0 X 19 1.8 1.0.188 8 X 19.0 1..188 0 X 19.0 08.1.0 8 X 19...0 0 X 19. 9.80.0 9 X 19. 8.8 01 - T ALUMINUM MILL FINISH TREAD PLATE Thickness Width Length Lbs/ Lbs/ (Inches) (In) (In) Sq/Ft Plate.100 8 X 19 1.7 100.8 8 X 10 1.90 7.00 8 X 1 1.90 91.0 8 X 19 1.90 11.0 0 X 1 1.90 11.00 0 X 19 1.90 1.00.188 8 X 1.8 1..188 8 X 19.8 180.8.188 0 X 19.8.0.0 X 1.70 1.0.0 8 X 10.70 18.00.0 8 X 1.70 177.0.0 8 X 19.70.80.0 0 X 19.70 9.00 0 1 8 87 9 metalsupermarkets.com
TREAD PLATE 01 - T ALUMINUM MILL FINISH TREAD PLATE Thickness Width Length Lbs/ Lbs/ (Inches) (In) (In) Sq/Ft Plate.7 8 X 1.9..7 8 X 19.9 1..7 0 X 19.9 9.0.7 7 X 19.9 7.0.00 8 X 19 7.7.8.00 0 X 19 7.7 81.0.00 7 X 19 7.7 97.9 00 BRIGHT TREAD ALUMINUM PLATE Thickness Width Length Lbs/ Lbs/ (Inches) (In) (In) Sq/Ft Plate.0 8 X 19.9 1..0 0 X 19.9 7.80.100 8 X 9 1.7 0..100 8 X 10 1.7.80.100 8 X 1 1.7 7..100 8 X 19 1.7 100.8.100 0 X 9 1.7.80.100 0 X 10 1.7 78.0.100 0 X 1 1.7 9.0.100 0 X 19 1.7 1.0 8 X 9 1.9 1. 8 X 10 1.9 7.80 8 X 1 1.9 9.1 8 X 180 1.9 11.0 8 X 19 1.9 1.88 0 X 10 1.9 9.00 0 X 1 1.9 11.0 0 X 19 1.9 1.0 7 X 1 1.9 18..188 8 X 10.8 11.80.188 8 X 1.8 1..188 8 X 19.8 180.8.188 0 X 1.8 19.0.0 8 X 1. 17.9.7 8 X 1...00 8 X 1 7.7.9 1 8 87 9 metalsupermarkets.com 1
RECTANGLES 1/8 X 1/ / 1 1-1/ 1-1/ 1-/ -1/ -1/ /1 X 1/ / 1 1-1/ 1-1/ 1-/ -1/ -1/ -1/ 1/ X 1/ / 1 1-1/ 1-1/ 1-/ -1/ -1/ -1/ -1/ 7 8 01 - T EXTRUDED ALUMINUM RECTANGLES.07.110.17.18.0.7.9.8.1.1.88.7.880.111.1.1.7..87..97...77.88 1.10 1.7.17.0.9.8.1.1.88..7.88 1.09 1.17 1. 1.70 1.7.08. 1/ X 9 10 11 1 /1 X 1/ / 1 1-1/ 1-1/ -1/ /8 X 1/ / 1 1-1/ 1-1/ 1-/ -1/ -1/ -/ -1/ -1/ -1/ 7 8 10 11 1 1/ X / 1 1-1/ 1-1/ 1-/ -1/..90.00.8.18.7.7.9.0.7.917 1.101 1.8 1.8.01.0.1.1.1..77.88.99 1.10 1.1 1. 1. 1.7 1.98.0...087.8.10.81.9.1.88.7.88 1.09 1.17 1. 1 8 87 9 metalsupermarkets.com
RECTANGLES 1/ X -1/ -/ -1/ -1/ -1/ -1/ 7 8 8-1/ 9 10 1 /8 X 1 1-1/ 1-1/ -1/ 8 9 10 1 / X 1 1-1/ 1-1/ -1/ -1/ -/ -1/ 7 8 9 01 - T EXTRUDED ALUMINUM RECTANGLES 1.70 1.17 1.7 1.911.08...90.8.8.11.70.998.9.880 7.0.7.919 1.10 1.70 1.88.0.90.7.10.880.1 7.0 8.80.88 1.10 1. 1.7 1.98.0...087.78.10.9.17 7.0 7.98 / X 10 1 1 X 1-1/ 1-1/ -1/ -1/ -/ 7 8 9 10 1 1-1/ X 1-1/ 1-/8 1-/ -1/ -1/ -1/ -/ -1/ 7 8 9 10 1 1-1/ X -1/ -1/ -/ -1/ -1/ 8.80 10.8 1.70 1.7...90..8.70.880 7.0 8. 9.08 10.8 11.70 1.11.0.89.7.90.07.7.10.1.1.880.1 7.0 8.80 10.90 11.70 1.0 1.700 17.0.8.99.10.81.9.7.17 7.0 8.80 1 8 87 9 metalsupermarkets.com
RECTANGLES 1-1/ X 7 8 9 10 1 1-/ X -1/ -1/ X -1/ -1/ -1/ 7 8 9 10 1-1/ X -/ -1/ 01 - T EXTRUDED ALUMINUM RECTANGLES 10.8 1.8 1.11 1.87 17.0 1.18.11.1.17 8. 9.1 10.90 1.8.880 7.0 8. 9.08 10.8 11.70 1.11 1. 18.81 1.18.0 8. 7.77 7.98 9.1-1/ X -1/ -1/ X -/ -1/ -1/ -/ X -1/ X -1/ -1/ -1/ X -1/ 8 10 X -1/ -1/ X 10.8 11.907 1.0 8.08 8.80 9. 10.90 11.70 1.700 17.0 9.70 11.19 1.9 1.8 1.11 1.87 17.0 1.18 1. 18..9.98 1.10 1.18.0 8..0.00 We reduced our in-house metal inventory by shopping at Metal Supermarkets. They are our one stop shopping source for any metal we need. 1 8 87 9 metalsupermarkets.com
ROUNDS 011 - T ALUMINUM ROUNDS 1/8.01 1-/1 1. /.0 1-/8 1.81 /1.0 1-7/1 1.98 7/.0 1-1/.19 1/.0 1-9/1. 1/.00 1-/8. 17/.07 1-/.99 9/.07 1-1/1.1 /1.09 1-7/8.7 11/.11 1-1/1.0 /8.1.88 /.11-1/1.08 7/1.18-1/8. 1/.10 -/1.9 1/.9-1/.88 17/.70 -/1.1 9/1.0 -/8.1 19/.8-1/.997 /8.7 -/8.1 1/.1 -/ 7.7 11/1. -7/8 7.9 /.9 8. /.8-1/8 9.71 1/1. -1/ 10.10 7/8.7-1/ 11.70 1/1.8 -/ 1.90 1.99 1.0 1-1/ 1.00-1/ 17.0 1-1/1 1.08-1/ 19.0 1-1/8 1.10 -/ 1.0 1-/1 1..990 1-1/ 1.99-1/8.00 1-9/ 1.7-1/.0 Order in person, by telephone, fax or email. 1 8 87 9 metalsupermarkets.com
ROUNDS 0 - T/T1 ALUMINUM ROUNDS 1/8.01 -/8.9 /1.0-1/.99 1/.09-9/1.1 /1.09 -/8.9 /8.1 -/ 7.199 7/1.18-7/8 7.88 1/.8 8.7 9/1.01-1/ 8.98 /8.71-1/8 9.9 11/1.9-1/ 10.00 /. -/8 10.80 1/1.8-1/ 11.0 7/8.78-9/1 1.080 1/1.8 -/ 1.90 1.91 1.0 1-1/1 1.07-1/1 1.710 1-1/8 1.0-1/ 17.190 1-/1 1.8-1/ 19.80 1-1/ 1.87 -/8 0.0 1-/1 1.0 -/ 1.80 1-/8 1.800.800 1-7/1 1.97-1/8.000 1-1/.1-1/.0 1-9/1. -1/ 8.800 1-/8.1.70 1-/.91-1/ 7.180 1-7/8.7-1/ 0.0 1-1/1.70 7.0.808 7-1/ 0.00-1/1.09 7-1/.0-1/8.98 8 0.90-1/.819 We have grinding, shearing, bending and other services. 1 8 87 9 metalsupermarkets.com
ROUNDS 1/8 /1 1/ /1 /8 1/ 9/1 /8 11/1 / 1/1 7/8 1/1 1 1-1/1 1-1/8 1-/1 1-1/ 1-/1 1-/8 1-7/1 1-1/ 1-/8 1-/ 1-7/8-1/8-1/ -/8-1/ 01 - T/T1 EXTRUDED ALUMINUM ROUNDS.01.0.07.090.19.0.9.0..19.09.707.811.9 1.0 1.19 1.0 1. 1.91 1.7 1.909.07.9.89.7.9.171.7.10.77 -/8 -/ -7/8-1/8-1/ -/8-1/ -/8 -/ -1/8-1/ -1/ -/ -1/ -1/ -/ -1/ -1/ -/ 7 7-1/ 8 8-1/ 9 11 1..98 7. 8.1 9.019 9.7 10.0 11.10 1.10 1.990 1.780 1.70 1.80 18.700 0.80.090.0 7.90 0.0.0.080 9.00.080.0 1.90 9.110.70 7.810 111.800 1.000 Wide variety of metals in rod, bar, sheet, plate, structural, tube & pipe. Stores coast-to-coast No minimums Same day delivery or pickup One stop shopping for any metal, cut and ready, fast! 1 8 87 9 metalsupermarkets.com 7
ROUNDS /8 7/1 1/ /8 / 7/8 1 1-1/8 1-1/ 1-/8 1-1/ 1-/8 1-/ 1-7/8-1/8 707 - T1 ALUMINUM ROUNDS.1.181.7.71..77.90 1.0 1.8 1.797.18.09.910.1.80.91-1/ -/8-1/ -/ -1/ -1/ -1/ -/ -1/ -1/ 7.811.1.90 7.187 8. 10.00 11.0 1.10 19.0 1.0.70.190.10 0.10.70 There is no upside to down time Wide variety of metals in rod, bar, sheet, plate, structural, tube & pipe. Stores coast-to-coast No minimums Same day delivery or pickup One stop shopping for any metal, cut and ready, fast! 8 1 8 87 9 metalsupermarkets.com
SHEET 1100 - H1 ALUMINUM SHEET MILL FINISH - NON HEAT-TREATABLE Thickness Size (Inches) Lbs/Sht.00(.8 Lbs./Sq. Ft.) X 9.77.0(. Lbs./Sq. Ft.) X 9 8.8.0(. Lbs./Sq.Ft.) X 9 10.8 8 X 9 1.7.00(. Lbs./Sq.Ft.) X 9 1. X 10 1.9 8 X 9 18.08 8 X 10.0 8 X 1 7.1.00(.70 Lbs./Sq.Ft.) X 9 1.9 X 10 1.18 8 X 9.9 8 X 10 8. 8 X 1.89.0(.889 Lbs./Sq.Ft.) x 9 1. X 10.7 8 x 9 8. 8 x 10. 8 x 1.8 Thickness Size (Inches) Lbs/Sht.080(1.17 Lbs./Sq.Ft.) 8 X 9.07 8 X 10.08 8 X 1.10.090(1.7 Lbs./Sq. Ft.) X 9 0.8 X 10 8. 8 X 9 0.77 8 X 10 0.9 8 X 1 1.1 (1.7 LBS./Sq. Ft.) X 9. X 10.9 8 X 9. 8 X 10 70. 8 X 1 8.8.10(. LBS./Sq. Ft.) 8 X 1 108.19.190(.8 Lbs./Sq.Ft.) X 9. X 10 80.0 8 X 9 8.7 8 X 10 107.0 8 X 1 18. what you want, when you want the way you want. At Metal Supermarkets, we stock a wide variety of ferrous, non-ferrous, and specialty products in a wide variety of shapes (bar, tube, channel, angle, sheet and plate, perforated sheet). If you don t see what you re looking for, Call! 1 8 87 9 metalsupermarkets.com 9
SHEET 00 - H1 ALUMINUM SHEET MILL FINISH - NON HEAT-TREATABLE Thickness Size (Inches).01.00.0.0.00.00.0 Lbs/Sht X 9.7 X 10.8 X 9.8 X 10 8. X 9 8. 8 X 9 11.0 8 X 10 1. 8 X 1 17.11 X 9 10.9 X 10 1.9 8 X 9 1.0 8 X 10 18. 8 X 1 1.90 X 9 1.8 X 10 17.11 8 X 9 18. 8 X 10.81 8 X 1 7.7 0 X 1.1 X 9 17.11 X 10 1.8 8 X 9.81 8 X 10 8.1 8 X 1.1 0 X 10. 0 X 1.77 X 9 1. X 10.9 8 X 9 8.7 Thickness Size (Inches) Lbs/Sht.0 8 X 10.9 8 X 1.11 0 X 10.91 0 X 1.89.080 X 9 7.8 8 X 10. 8 X 1.77 0 X 10 7.0 0 X 1 8..090 X 9 0.79 8 X 10 1. 8 X 1 1.8 0 X 1 7.98.100 X 9. 8 X 10 7.0 8 X 1 8. 0 X 1 8. X 9.77 X 10. 8 X 9 7.0 8 X 10 71.8 8 X 1 8. 0 X 1 10.90 7 X 1 18.0.10 8 X 1 108.19.190 X 9.0 8 X 10 108.0 8 X 1 10.00 0 X 1 1.0 7 X 1 19.00 Call /7 through our after hours program. 0 1 8 87 9 metalsupermarkets.com
SHEET 0 - H ALUMINUM SHEET MILL FINISH - NON HEAT-TREATABLE Thickness Size (Inches).00.0.0.00.00.0.080 Lbs/Sht X 9.70 X 9 8.81 8 X 9 11.170 X 9 10.70 8 X 10 17.880 8 X 1 1.0 X 9 1.10 8 X 9 17.880 8 X 10.0 8 X 1.80 X 9 1.70 8 X 9.0 8 X 10 7.90 8 X 1.0 0 X 1 1.900 X 9 1.10 8 X 9 8.10 8 X 10.00 8 X 1.0 0 X 1.800 X 9.810 8 X 9.70 8 X 10.80 8 X 1.0 Thickness Size (Inches).090.100.10.190 Lbs/Sht X 9 0.170 8 X 9 0.0 8 X 10 0.80 8 X 1 0.0 0 X 1 7.0 X 10 1.910 8 X 10.880 8 X 1 7.00 X 9 1.900 X 10.80 8 X 9.870 8 X 10 9.80 8 X 1 8.810 0 X 10 87.00 0 X 1 10.800 7 X 9 8.810 7 X 10 10.800 7 X 1 1.700 8 X 1 107.00 X 9.700 8 X 9 8.90 8 X 10 10.00 8 X 1 17.00 0 X 10 1.700 7 X 9 17.00 7 X 1 191.100 what you want, when you want the way you want. We ll load your order or deliver your order to you. 1 8 87 9 metalsupermarkets.com 1
SHEET 01 - T ALUMINUM SHEET MILL FINISH - HEAT TREATABLE Thickness Size (In.).0.00.00.0.080.090.100 Lbs./ Lbs/Sht Sq.Ft 8 X 1. 1.70 8 X 1. 7.1 8 X 10.70 8. 8 X 1.70.89 0 X 1.70. 8 X 9.88 8. 8 X 10.88. 8 X 1.88.7 0 X 1.88. 8 X 10 1.1.08 8 X 1 1.1.10 0 X 1 1.1 7. 8 X 1 1.7 1.1 0 X 1 1.7 7. 8 X 10 1.1. Thickness Size (In.).100.10.190 Lbs./ Lbs/Sht Sq.Ft 8 X 1 1.1 7.7 X 9 1.7. 8 X 9 1.7. 8 X 10 1.7 70. 8 X 1 1.7 8.7 0 X 1 1.7 10.8 7 X 1 1.7 17.01 8 X 1. 108.19 X 9.8. 8 X 9.8 8.9 8 X 10.8 107.0 8 X 1.8 18.88 0 X 10.8 1. 0 X 1.8 11.10 7 X 9.8 0.9 7 X 10.8 11.10 7 X 1.8 19. When our assembly line went down, we needed a piece of cold rolled steel cut to size. Within minutes, Metal Supermarkets delivered it to our back door. 1 8 87 9 metalsupermarkets.com
SQUARES /8 1/ /8 / 7/8 1 1-1/8 1-1/ 1-1/ 0 - T1/T ALUMINUM SQUARES.18.99.8.7.917 1.198 1.17 1.87.9 1-/ -1/ -1/ -/ -1/ -1/.70.79.07 7.00 9.0 10.800 1.0 1.700 19.170 1/ /8 / 7/8 1 1-1/ 1-1/ 1-/8 1-/ 01 - T EXTRUDED ALUMINUM SQUARES.9.9.1.901 1.17 1.88..108.00.70-1/ -1/ -/ -1/ -1/ -1/.9 7.0 8.89 10.80 1.10 18.80.810 9.00.70.0 / 1 1-1/ 707 - T1 EXTRUDED ALUMINUM SQUARES.81 1.1.77 1-/.71.88 what you want, when you want the way you want. At Metal Supermarkets, we stock a wide variety of ferrous, non-ferrous, and specialty products in a wide variety of shapes (bar, tube, channel, angle, sheet and plate, perforated sheet). If you don t see what you re looking for, Call! 1 8 87 9 metalsupermarkets.com
TUBING 01 - T DRAWN SEAMLESS TUBING O.D. Wall I.D. Lbs/Ft. /1.0.118.019.09.090.0 1/.0.180.07.09.1.0.08.1.01 /1.0..0.09.1.07.08.197.0 /8.0.0.0.09.77.09.08.9.07.0..07 7/1.0.8.0.09.0.070.0.08.089 1/.08..08.0.0.00.09.0.081.08.8.09 1/.0.70.10.10.0.18 /8.08.9.01.0..07.09.7.10.08.09.11.0.9.1 /.0.80.09.09..1.08..18.0.0.1.08.8.0 7/8.0.80.108.09.777.19.08.79.17.0.7.19 1.0.90.1.09.90.17 O.D. Wall I.D. Lbs/Ft. 1.08.88.01.0.870..08.8.81.70.0 1-1/8.0 1.0.10.08 1.009.8 1-1/.0 1.180.17.09 1.1.17.08 1.1..0 1.10.8.08 1.08.7 1-/8.0 1.0.17.09 1.77.0.08 1.9.8 1-1/.0 1.0.189.09 1.0..08 1.8.09.0 1.70..08 1.. 1-/8.0 1..0.08 1.09. 1-/.08 1...08 1.8.11 1-7/8.08 1.79.89.09 1.90..08 1.88.1.0 1.870..08 1.8.87-1/.09.1.98.0.10..08.08. -1/.0.70.8.08..71.0.870.70.08.8.89.0.870.9 We source hard to find metals. 1 8 87 9 metalsupermarkets.com
TUBING 01-11 EXTRUDED SEAMLESS ROUND TUBING O.D. Wall I.D. Lbs/Ft. (Inch) (Inch) 1-1/ X 1/8 1.0. 1/ 1.000 1.1 X 1/8 1.70.8 1/ 1.00 1.1-1/ X 1/8.0 1.097 1/.000.078 1/ 1.00.9 -/ X 1/ 1.70.1 /8 1.00.907 X 1/8.70 1.8 1/.00.0 1/.000.18 / 1.00. -1/ X /8.00.98 1/.0.080-1/ X 1/.00. /.000 7.0 -/ X 1/.70.00 X 1/8.70 1.788 O.D. Wall I.D. Lbs/Ft. (Inch) (Inch) X 1/.00. 1/.000. /.00 9.00-1/ X 1/.00 7.89 /.000 10.90 X 1/.000 8.1 /.00 11.780 1.000 1.780-1/ X 1/.00 9. /.000 1.10 1.00 1.0 X 1/.000 10.10 /.00 1.0-1/ X 1.00 0.0 7 X 1/.000 1.010 /.00 17.0 1.000.170 8 X 1/ 7.00 7.18 1/ 7.000 1.80 1.000.80 The art of metal work We ll go to great lengths to help you find the perfect metal for your masterpiece. Wide variety of metals in bar, sheet, plate, structural, tube & pipe Stores coast-to-coast No minimums Same day delivery or pickup 1 8 87 9 metalsupermarkets.com
TUBING 0 - T EXTRUDED RECTANGULAR TUBING (Typically Sharp Corners) Size (inches) 1/ X 1 1/ X 1-1/ / X 1-1/ / X -1/ 1 X 1-1/ 1 X 1 X -1/ 1 X 1-1/ X 1-1/ X -1/ 1-1/ X 1-1/ X 1-1/ X 1-1/ X 1-1/ X 1-/ X 1-/ X 1-/ X Nominal Wall Lbs/Ft. Thickness.0.8.1.88.88..808.9 1.10.88 1.09 1.17.9 1.7 1.0 1.7 1.09 1. 1.17 Size (inches) 1-/ X X X X X X X X X X X X X X X X 8 X 8 Nominal Wall Lbs/Ft. Thickness.0.188.188.188.188.0.188.0.00.0.7 1.911 1.9 1. 1.90.87 1.98.78.8 1.98.989.71.10.81.8 10.8.7 10.80 0 - T EXTRUDED SQUARE TUBING (Typically Sharp Corners) Size O.D. Nominal Wall Lbs/Ft. (inches) Thickness / / 1 1 1-1/ 1-1/ 1-1/ -1/ -1/ -/.0.0.188.188.0.0.18.8.7.1..808 1.10 1.10 1.0.08 1.9. 1. Size O.D. Nominal Wall Lbs/Ft. (inches) Thickness -/ -1/.188.188.0.188.0.00.188.0.0.00. 1.90.87. 1.98.78.71.10 8...88.7 1.9 Order only what you need. 1 8 87 9 metalsupermarkets.com