The Faculty of Engineering and Science Board of Studies for Industry and Global Business Development Curriculum for the Master s Program in Design of Mechanical Systems Aalborg University 2014 Campus Aalborg
Preface Pursuant to Act 367 of March 25, 2013 on Universities (the University Act) with subsequent changes, the following curriculum for the Master's program in Design of Mechanical Systems is stipulated. The program also follows the Framework Provisions and the Examination Policies and Procedures for the Faculty of Engineering and Science. 1
Table of contents 1: Legal Basis of the Curriculum, etc. 1.1 Basis in Ministerial Orders 1.2 Faculty Affiliation 1.3 Board of Studies affiliation 2: Admission, Degree Designation, Program Duration and Competence Profile 2.1 Admission 2.2 Degree designation in Danish and English 2.3 The program s specification in ECTS credits 2.4 Competence profile on the diploma 2.5 Competence profile of the program 3: Content and Organisation 3.1 Programme Overview 3.2. Design of Mechanical Systems, 1st semester 3.2.1 Stress and Deformation Analyses of Load Carrying Structural Elements 3.2.2 Solid Mechanics with Microstructure 3.2.3 Fracture Mechanics and Fatigue 3.2.4 Finite Element Methods 3.3. Design of Mechanical Systems, 2nd Semester 3.3.1 Engineering Design of Mechanical Systems 3.3.2 Engineering Optimization Concepts, Methods and Applications 3.3.3 Mechanics of Composite Materials and Structures 3.3.4 Energy and Variational Methods with Applications 3.4. Design of Mechanical Systems, 3rd Semester 3.4.1 Industrial development 3.5. Design of Mechanical Systems, 4th Semester 4: Entry into Force, Interim Provisions and Revision 5: Other Provisions 5.1 Rules concerning written work, including the Master s thesis 5.2 Rules concerning credit transfer (merit), including the possibility for choice of modules that are part of another program at a university in Denmark or abroad 5.3 Rules for examinations 5.4 Exemption 5.5 Additional information 2
Chapter 1: Legal Basis of the Curriculum, etc. 1.1 Basis in Ministerial Orders The Master s program in Design of Mechanical Systems is organized in accordance with the Ministry of Science, Technology and Innovation s Ministerial Order no. 814 of June 29, 2010 on Bachelor s and Master s Programs at Universities (the Ministerial Order of the Study Programs) and Ministerial Order no. 666 of June 24, 2012 on University Examinations (the Examination Order) with subsequent changes. Further reference is made to Ministerial Order no. 241 of March 11, 2013(the Admission Order) and Ministerial Order no. 250 of March 15, 2007 (the Grading Scale Order) with subsequent changes. 1.2 Faculty affiliation The Master s program falls under the Faculty of Engineering and Science, Aalborg University. 1.3 Board of Studies affiliation The Master s program falls under the Board of Studies for Industry and Global Business Development in the School of Engineering and Science. Chapter 2: Admission, Degree Designation, Program Duration and Competence Profile 2.1 Admission Admission to the Master s program in Design of Mechanical Systems requires a Bachelor s degree in Mechanical Engineering and Manufacturing, Innovation and product design or the like. Students with another Bachelor's degree, upon application to the Board of Studies, will be admitted after a specific academic assessment if the applicant is deemed to have comparable educational prerequisites. The University can stipulate requirements concerning conducting additional exams prior to the start of study. 2.2 Degree designation in Danish and English The Master s program entitles the graduate to the Danish designation civilingeniør, cand.polyt. (candidatus/candidata polytechnices) i design af mekaniske systemer. The English designation is: Master of Science (MSc.) in Engineering (Design of Mechanical Systems). 2.3 The program s specification in ECTS credits The Master s program is a 2-year, research-based, full-time study program. The program is set to 120 ECTS credits. 2.4 Competence profile on the diploma The following competence profile will appear on the diploma: A graduate of the Master s program has competencies acquired through an educational program that has taken place in a research environment. The graduate of the Master s program can perform highly qualified functions on the labour market on the basis of the educational program. Moreover, the graduate has prerequisites for research (a Ph.D. program). Compared to the Bachelor s degree, the graduate of the Master s program has developed her/his academic knowledge and independence, so that the graduate can independently apply scientific theory and method in both an academic and occupational/professional context. 3
2.5 Competence profile of the program The graduate of the Master s program: Knowledge Has attained thorough understanding of a broad range of theoretical, numerical and experimental techniques within the area of design of mechanical systems. Has knowledge in one or more subject areas that, in selected areas within mechanical engineering, is based on the highest international research in a subject area. Can understand and, on a scientific basis, reflect over subject area s related to mechanical engineering and identify scientific problems within that area. Demonstrate an understanding of research work and be able to become a part of a research environment. Demonstrate insight into the implications of research work, including research ethics. Skills Be able to apply scientific methodology to the solving of a wide variety of problems within the field of specialization. Be able to perform scientific work in relevant topics of the field of the specialization. Be able to apply a wide range of engineering methods in research and development projects in the field of specialization. Be able to participate or lead projects in mechanical system design, product development, modeling and analysis of mechanical systems, materials technology, production technology, structural mechanics and design of lightweight structures. Can communicate research-based knowledge and discuss professional and scientific problems with both peers and nonspecialists. Can use advanced laboratory test set ups and data collection methods. Competencies Be able to work independently with a project on a specific problem within their field of interest on the highest possible level within their specialization. Be able to take part in technical development and research. Can manage work and development situations that are complex, unpredictable and require new solutions within the area of mechanical engineering. Can independently initiate and implement discipline-specific and interdisciplinary cooperation and assume professional responsibility. Be able to direct the technical management of development projects within the industry. Be competent to solve new and complicated technical problems by the use of advanced mathematics, scientific and technological knowledge. Can independently take responsibility for own professional development and specialization. 4
Chapter 3: Content and Organization of the Program The M.Sc. program in Design of Mechanical Systems aims at educating graduates, who are qualified to take part in technical development and research and who are able to direct the technical management of development projects within the industry. The graduates are expected to have gained a broad knowledge within the areas of mechanical system design, product development, modeling and analysis of mechanical systems, materials technology, production technology, structural mechanics and design of lightweight structures. Also, the graduates are expected to be competent to solve new and complicated technical problems by the use of advanced mathematics, scientific and technological knowledge. The program is structured in modules and organized as a problem-based study. A module is a program element or a group of program elements, which aims to give students a set of professional skills within a fixed time frame specified in ECTS credits, and concluding with one or more examinations within specific exam periods that are defined in the curriculum. The program is based on a combination of academic, problem-oriented and interdisciplinary approaches and organized based on the following work and evaluation methods that combine skills and reflection: lectures classroom instruction project work workshops exercises (individually and in groups) teacher feedback reflection portfolio work The third semester offers different ways of organisation depending on the student s choice of content; project work at Aalborg University, study visit at an educational institution in Denmark or abroad, voluntary traineeship with project work at a company in Denmark or abroad, or a semester programme that comprises cross-disciplinary programme elements composed by the student. The total work load of the semester has to be equivalent to 30 ECTS, of which up to 15 ECTS can be elective courses. The project may be finalized with a project report or in the form of a scientific paper, or, if the project is continued at the 4th semester, with a midterm evaluation. For further information about the organisation of the module please see the Framework Provisions, chapter 9.4.1. At the 4th semester, the master thesis is completed. The master thesis can be combined with the 3rd semester in an extended master thesis. 5
Overview of the program All modules are assessed through individual grading according to the 7-point scale or Pass/Fail. All modules are assessed by external examination (external grading) or internal examination (internal grading or by assessment by the supervisor only). Semester Module ECTS Grading Exam Stress and Deformation Analyses 15 7-point scale Internal of Load Carrying Structural Element 1. Solid Mechanics with 5 7-point scale Internal Microstructure Fracture Mechanics and Fatigue 5 7-point scale Internal Finite Element Methods 5 7-point scale Internal 2. Engineering Design of 15 7-point scale External Mechanical Systems Engineering Optimization 5 7-point scale Internal Concepts, Methods and Applications Mechanics of Composite 5 7-point scale Internal Materials and Structures Energy and Variational Methods 5 7-point scale Internal with Applications 3.* Industrial Development 1 15-30 7-point scale Internal 4. Design of Mechanical Systems 30 7-point scale External * According to the framework provisions students are offered a choice of an individually planned semester comprising of a traineeship/scientific paper/overseas studies or a long dissertation. 1 The project must be equivalent to at least 15 ECTS. Course modules approved by the Study Board for Industry and Global Business Development for the specific study must supplement to a total of 30 ECTS. 6
3.2 Design of Mechanical Systems, 1st semester 3.2.1 Stress and Deformation Analyses of Load Carrying Structural Elements (15 ECTS) Title: Stress and Deformation Analyses of Load Carrying Structural Elements (Spændings- og deformationsanalyse af kraftoverførende konstruktion) Prerequisites: The student must meet the admission requirements described in chapter 2.1 Goal: Knowledge Skills Competences Students who complete the module are expected to: Have gained an in-depth understanding of theoretical and experimental determination of the stress and deformation states occurring in a structural element when carrying a mechanical load. Have attained an understanding for methods of analysis and experimental methods and the characteristics of their applications and limitations. Be able to set up the governing equations for the theory of elasticity. Be able to demonstrate the properties of the strain and stress tensors. Be able to account for the implementation and practical use of the analytical, numerical, and experimental methods applied in the project. Be able to give a critical evaluation of the methods applied for stress and deformation analyses and the results obtained. Be able to use correct terminology. Be able to compare theoretical and experimental results. Be able to critically evaluate applied methods and their results. Be able to analyze a load carrying element on the basis of model considerations, using continuum mechanics, and by applying numerical methods including the finite element method. Be able to investigate the behavior of a structural element under mechanical loading with experimental techniques such as strain gauges and digital image measurement techniques. Be able to compare theoretical and experimental results carefully, and critically evaluate the methods applied and the results obtained. Be able to apply the background and the insight obtained, on intuitive design optimization, and suggest geometrical changes or a redesign including change of material. Teaching Method: The module is carried out as group-based problem-oriented project work. The group work is carried out as an independent work process in which the students themselves organize and coordinate their workload in collaboration with a supervisor. The project is carried out in groups with normally no more than 6 members. Form of examination: Internal, oral group examination Evaluation criteria: As stated in the Framework Provisions 7
3.2.2 Solid Mechanics with Microstructure (5 ECTS) Title: Solid Mechanics with Microstructure (Materialemekanik) Prerequisites: The student must meet the admission requirements described in chapter 2.1 Goal: Students who complete the module are expected to: Knowledge Skills Have gained an understanding of basic mechanical properties of engineering materials and modeling procedures used to quantify these properties, as well as the ways in which these properties characterize material response. Be able to understand basic continuum mechanical theories and apply them to simple structural components. Be able to substantiate different observable deformation modes by underlying physical mechanisms. Be able to document knowledge related to the application of selected analytical/numerical methods for materials characterization. Competences Have gained an awareness of various responses exhibited by solid engineering materials when subjected to mechanical loadings and an explanation of the physical mechanisms associated with design-limiting behavior of engineering materials. Have gained an understanding of predictive analytical and computational frameworks that provide quantitative skills to deal with materials-limiting problems in engineering design. Teaching Method: The form(s) of teaching will be determined and described in connection with the planning of the semester. The description will account for the form(s) of teaching and may be accompanied by an elaboration of the roles of the participants (see chapter 3).The course/project theme is performed in either English or Danish dependent of the language skills of the participants. Form of examination: Internal, oral/written examination Evaluation criteria: As stated in the Framework Provisions 8
3.2.3 Fracture Mechanics and Fatigue (5 ECTS) Title: Fracture Mechanics and Fatigue (Brudmekanik og udmattelse) Prerequisites: The student must meet the admission requirements described in chapter 2.1 Goal: Students who complete the module are expected to: Knowledge Have gained a comprehensive understanding of fracture mechanics. Have gained knowledge in applying classical methods in designing against fatigue fracture by studying notches and their effect, by studying strainfatigue, and by analysing eigen-stress states. Have gained an understanding of how to apply fracture mechanics in the assessment of reliability of practical designs and machine elements. Skills Competences Be able to assess the stability of cracks using Griffith s and Irwin s fracture criteria, energy release rate, and toughness concepts Be able to apply linear elastic solutions for sharp cracks and obtain the stress intensity factor. Be able to assess mixed mode loading and apply crack growth direction hypotheses Be able to assess crack growth by fatigue, partial damage and load spectra. Be able to assess crack initiation, notches and their effect. Be able to determine life time and apply methods for improving the fatigue strength and life time of machine elements and welded details. Be able to understand and apply linear elastic concepts in assessing the stability of cracked structures under static and fatigue loading. Be able to distinguish between different fatigue regimes, i.e. elastic or plastic, and un-cracked or pre-cracked, and apply correct methodology to each case in relevant structures. Be able to determine the lifetime of welded components, and explain fatigue in welded components on the basis of fracture mechanical concepts. Teaching Method: The form(s) of teaching will be determined and described in connection with the planning of the semester. The description will account for the form(s) of teaching and may be accompanied by an elaboration of the roles of the participants (see chapter 3).The course/project theme is performed in either English or Danish dependent of the language skills of the participants. Form of examination: Internal, written/oral examination. Evaluation criteria: As stated in the Framework Provisions 9
3.2.4 Finite Elements Methods (5 ECTS) Title: Finite Element Methods (Elementmetoder) Prerequisites: The student must meet the admission requirements described in chapter 2.1 Goal: Students who complete the module are expected to: Knowledge Skills Competences Be able to use the finite element method in static stress analysis. Have knowledge of element technology, such as bar, beam, solid and shell elements. Be able to apply methods for error estimation and adaptive mesh generation. Be able to solve structural dynamics and vibrations problems using methods such as free vibrations, modal methods and direct time integration methods. Be able to apply nonlinear finite element methods including solution of systems of nonlinear equations, geometrically nonlinear problems, contact problems, and nonlinear material models. Be able to perform linearised buckling analysis. Be able to solve exercises using a commercial finite element program (e.g., ANSYS). Demonstrate a basic understanding of concepts, theory and applications of finite element analysis from a mechanical engineering view point. Be able to perform linear and nonlinear static and dynamic stress analysis including the use of commercial finite element software. Be able to apply the concepts, theories and techniques covered in the area of linear and nonlinear finite element analysis on practical problems. Be able to apply the concepts and theories to the solution of relevant problems using commercial software programs. Teaching Method: The form(s) of teaching will be determined and described in connection with the planning of the semester. The description will account for the form(s) of teaching and may be accompanied by an elaboration of the roles of the participants (see chapter 3).The course/project theme is performed in either English or Danish dependent of the language skills of the participants. Form of examination: Internal, oral/written examination Evaluation criteria: As stated in the Framework Provisions 10
3.3 Design of Mechanical Systems, 2nd semester 3.3.1 Engineering Design of Mechanical Systems (15 ECTS) Title: Prerequisites: Goal: Engineering Design of Mechanical Systems (Konstruktion af mekaniske systemer) 1st semester at the M. Sc. in Design of Mechanical Systems program or the like. Students who complete the module are expected to: Knowledge Have gained knowledge and understanding of advanced engineering design of mechanical systems and structures. Be able to understand and apply advanced analysis tools for evaluating the performance of advanced mechanical systems and structures. Skills Competences Be able to apply advanced engineering design on mechanical systems and structures. Be able to use advanced materials for structural design. Be able to understand and apply advanced analysis tools for evaluating the performance of advanced mechanical systems and structures. Be able to apply synthesis and analysis in the design process, and demonstrate their interdependence. Be able to apply systematic rational design methods. Be able to design solutions for a load carrying mechanical system or structure, with an industrial partner or with industrial relevance. Be able to consider a problem of sufficient complexity to encompass the use of advanced analytical, numerical or experimental analysis tools for predicting the performance of the mechanical system or structure during operation. Be able to analyse challenging designs from a structural point of view, where lightweight design, use of advanced materials like composite materials, design problems involving fatigue, and mechanical systems with complicated dynamic behaviour during operation may be considered. Be able to document a final design with respect to performance using virtual prototypes or analytical models, and include manufacturing considerations. Teaching Method: The module is carried out as group-based problem-oriented project work. The group work is carried out as an independent work process in which the students themselves organize and coordinate their workload in collaboration with a supervisor. The project is carried out in groups with normally no more than 6 members. Form of examination: Oral examination with participation of an external examiner. 11
Evaluation criteria: As stated in the Framework Provisions 12
3.3.2 Engineering Optimization Concepts, Methods and Applications (5 ECTS) Title: Prerequisites: Goal: Engineering Optimization Concepts, Methods and Applications (Ingeniørmæssig optimering begreber, metoder og anvendelser) 1st semester at the MSc. in Design of Mechanical Systems program or the like. Students who complete the module are expected to: Knowledge Skills Competences Have gained an in-depth understanding of important concepts and methods of optimization for efficient solution of optimization problems within different areas of engineering, including design optimization of mechanical systems. Be able to use optimization concepts and topics. Be able to use numerical methods of unconstrained optimization. Be able to use numerical (mathematical programming) methods for optimization of multi-dimensional functions with constraints. Be able to solve multicriterion optimization problems. Be able to apply other methods of optimization, such as integer problems, response surface methods, genetic algorithms, etc. Be able to perform general applications of optimization methods: parameter identification, optimization as an analysis tool for problems governed by an extremum principle, surrogate and metamodelling problems. Be able to apply the concepts, theories and methods for solution of engineering optimization problems. Be able to account for the considerations involved in the process of formulating and modeling an engineering optimization problem, choosing an advantageous method of solution, and implementing it in practice. Teaching Method: The form(s) of teaching will be determined and described in connection with the planning of the semester. The description will account for the form(s) of teaching and may be accompanied by an elaboration of the roles of the participants (see page 5).The course/project theme is performed in either English or Danish dependent of the language skills of the participants. Form of examination: Internal, written/oral examination. Evaluation criteria: As stated in the Framework Provisions 13
3.3.3 Mechanics of Composite Materials and Structures (5 ECTS) Title: Prerequisites: Goal: Mechanics of Composite Materials and Structures (Kompositmaterialers og -konstruktioners mekanik) 1st semester at the M. Sc. in Design of Mechanical Systems program or the like. Students who complete the module are expected to: Knowledge Skills Competences Have gained an in-depth understanding of the overall topical area of composite materials including their properties, manufacturing, analysis and design. Be able to document understanding of the following concepts and theories: o Applications of composites. o Fibers and polymer resin materials: Types and properties. o Manufacturing methods, their processing characteristics and influence on the mechanical properties of composites. o Laminae and laminates: Micro-mechanical models, modeling of the laminae, classical lamination theory (CLT). o Analysis of composite structures: Beam, plate and shell modeling. o Thermal effects. o Fracture and failure. o Sandwich structures. o Adhesive bonded and mechanical joints, load introduction aspects, 3D effects and general principles for design. o Finite element analysis of laminated composite structures. Be able to apply concepts, theories and methods for analysis and design of composite materials and complex structures made from composite materials to real-life problems. Be able to undertake development and product design using composite materials. Be able to develop procedures for production and verification of components made from composite materials. Teaching Method: The form(s) of teaching will be determined and described in connection with the planning of the semester. The description will account for the form(s) of teaching and may be accompanied by an elaboration of the roles of the participants (see page 5).The course/project theme is performed in either English or Danish dependent of the language skills of the participants. Form of examination: Internal, written/oral examination. Evaluation criteria: As stated in the Framework Provisions 14
3.3.4 Energy and Variational Methods with Applications (5 ECTS) Title: Prerequisites: Goal: Energy and Variational Methods with Applications (Energi- og variationsmetoder med anvendelser) 1st semester at the MSc. in Design of Mechanical Systems program or the like. Students who complete the module are expected to: Knowledge Have gained an in-depth understanding of the overall topical area of energy and variational methods and classical principles of stationarity, and their application for the formulation and solution of general problems in statics and dynamics of mechanical systems, including: o Energy methods and energy minimization principles o Variational methods (methods of Ritz, Galerkin, Rayleigh and Rayleigh-Ritz) o o Energy methods as the foundation of the finite element method Different applications such as analysis of statics, buckling and vibration of beams, plates and similar Skills Competences Be able to apply energy and variational methods for the solution of problems in statics and dynamics involving discrete and continuous mechanical systems. Be able to apply energy minimization / maximization principles to derive the relationships between stresses, strains, displacements, material properties, and external effects (e.g., temperature) in the form of balance of the kinetic and potential energies and the work done by internal and external forces. Be able to apply energy principles in mechanics to express the relationships between stresses, strains, displacements, material properties, and external effects in the form of energy or work done by internal and external forces. Be able to use the variational calculus as a convenient and robust tool for formulating the governing equations of statics and dynamics of rigid and solid bodies in applied mechanics. Be able to use energy as a scalar quantity, and use the variational relationships to provide a convenient and alternative means for formulating the governing equations of deformable and rigid bodies in solid mechanics Be able to apply the energy and variational methods to find approximate analytical and numerical (e.g. finite element) solutions of complex problems in statics and dynamics of mechanical systems Be able to apply the energy and variational principles in approximate analytical and numerical solutions (e.g. finite element methods) of complex mechanical systems, bypassing the difficult task of formulating and solving in exact form the set of governing partial differential equations. Teaching Method: The form(s) of teaching will be determined and described in connection with the planning of the semester. The description will account for the form(s) of 15
teaching and may be accompanied by an elaboration of the roles of the participants (see page 5).The course/project theme is performed in either English or Danish dependent of the language skills of the participants. Form of examination: Internal, oral/written examination Evaluation criteria: As stated in the Framework Provisions 16
3.4 Design of Mechanical Systems, 3rd semester 3.4.1 Industrial Development (15-30 ECTS) Title: Prerequisites: Goal: Industrial Development, Scientific paper or Internship (Industrielt udviklingsarbejde) 2nd semester at the MSc. in Design of Mechanical Systems program or the like. Students who complete the module are expected to: Knowledge Have gained knowledge and understanding of advanced engineering design of mechanical systems and structures. Be able to understand and apply advanced analysis tools for evaluating the performance of advanced mechanical systems and structures. Have knowledge and comprehension of the relation between synthesis and analysis in the design process. Skills Competences Be able to describe the problem solved and the criteria applied for its solution. Be able to evaluate the concepts, theories, and methodologies applied in the solution of the problem. Be able to account for the choices made during the solution of the problem, and substantiate that these are made on a high professional level. Be able to assess the limitations of the concepts, theories, and methodologies applied in the solution of the problem. Be able to analyze and solve an actual problem, of industrial relevance, through application of systematic research and development processes, including advanced analytical, experimental, and/or numerical methods and models. Organization: Dependent on student s choice of content and organization of the semester; the student may choose between project work at Aalborg University or a voluntary traineeship at a company in Denmark or abroad. The total work load of the semester has to be equivalent to 30 ECTS. If carried out at Aalborg University, the project may be finalized with a project report or in the form of a scientific paper. If continued at the 4th semester, the project is evaluated with a midterm evaluation. For further information about the organisation of the module please see the Framework Provisions, chapter 9.4.1. Teaching Method: Dependent on student s choice of content and organization of the semester; If the semester is carried out as an internship, the student is included in the company s daily work. Concurrent to the work in the company, the student makes a report, which is evaluated after the ending of the internship; 17
The project work is carried out as an independent work process in which the students themselves organize and coordinate their workload in collaboration with a supervisor. The project may be carried out individually or in groups. Form of examination: Internal, Oral examination (please see the program s study guide for further information) Evaluation criteria: As stated in the Framework Provisions 18
3.5 Design of Mechanical Systems, 4th semester 3.5.1 Design of Mechanical Systems (30 ECTS) Title: Prerequisites: Goal: Master s Thesis Kandidatspeciale Successful conclusion of the first three semesters at the Design of Mechanical Systems program. Exemptions to this rule can be given, but only by decision of the Study Board of Industry and Global Business Development in accordance with the rules given in the framework provisions. Students who complete the module are expected to: Knowledge Skills Have attained thorough understanding of a broad range of theoretical, numerical and experimental techniques within the area of design of mechanical systems. Be able to apply scientific methodology to solve a wide variety of problems within the field of specialization. Be able to perform scientific work in relevant topics within the field of specialization. Be able to apply a wide range of engineering methods in research and development projects in the field of specialization. Be able to participate or lead projects in mechanical system design, product development, modeling and analysis of mechanical systems, materials technology, production technology, structural mechanics and design of lightweight structures. Competences Be able to work independently with a project on a specific problem within their field of interest on the highest possible level within their specialization. Be able to take part in technical development and research Be able to direct the technical management of development projects within the industry. Be competent to solve new and complicated technical problems by the use of advanced mathematics, scientific and technological knowledge. Teaching Method: In this module, the Master s project is carried out. The module constitutes independent project work and concludes the program. Within the approved topic, the Master s project must document that the level for the program has been attained. Form of examination: Oral examination with participation of an external examiner. Evaluation criteria: As stated in the Framework Provisions 19
Chapter 4: Entry into Force, Interim Provisions and Revision The curriculum is approved by the Dean of the Faculty of Engineering and Science and enters into force as of September 2014. In accordance with the Framework Provisions for the Faculty of Engineering and Science at Aalborg University, the curriculum must be revised no later than 5 years after its entry into force. Chapter 5: Other Provisions 5.1 Rules concerning written work, including the Master s thesis In the assessment of all written work, regardless of the language it is written in, weight is also given to the student's spelling and formulation ability, in addition to the academic content. Orthographic and grammatical correctness as well as stylistic proficiency are taken as a basis for the evaluation of language performance. Language performance must always be included as an independent dimension of the total evaluation. However, no examination can be assessed as Pass on the basis of language performance alone; similarly, an examination normally cannot be assessed as Fail on the basis of poor language performance alone. The Board of Studies can grant exemption from this in special cases (e.g., dyslexia or a native language other than Danish). The Master s thesis must include an English summary. 2 If the project is written in English, the summary must be in Danish. 3 The summary must be at least 1 page and not more than 2 pages. The summary is included in the evaluation of the project as a whole. 5.2 Rules concerning credit transfer (merit), including the possibility for choice of modules that are part of another program at a university in Denmark or abroad In the individual case, the Board of Studies can approve successfully completed (passed) program elements from other Master s programs in lieu of program elements in this program (credit transfer). The Board of Studies can also approve successfully completed (passed) program elements from another Danish program or a program outside of Denmark at the same level in lieu of program elements within this curriculum. Decisions on credit transfer are made by the Board of Studies based on an academic assessment. See the Framework Provisions for the rules on credit transfer. 5.3 Rules for examinations The rules for examinations are stated in the Examination Policies and Procedures published by the Faculties of Engineering and Science on their website. 5.4 Exemption In exceptional circumstances, the Board of Studies study can grant exemption from those parts of the curriculum that are not stipulated by law or ministerial order. Exemption regarding an examination applies to the immediate examination. 5.5 Additional information The current version of the curriculum is published on the Board of Studies website, including more detailed information about the program, including exams. Completion of the Master s program The Master s program must be completed no later than four years after it was begun. 2 Or another foreign language (upon approval from the Board of Studies). 3 The Board of Studies can grant exemption from this. 20
Rules and requirements concerning the reading of texts in foreign languages and a statement of the foreign language knowledge this assumes It is assumed that the student can read academic texts in modern Danish, Norwegian, Swedish and English and use reference works, etc., in other European languages. 21