European Aviation Safety Agency EASA TYPE-CERTIFICATE DATA SHEET Number: E.070 Issue: 05 Date: 16 November Type: GE Aviation Czech M601/H80 series turboprop engines Models: M601D M601D-1 M601D-2 M601D-11 M601D-11NZ M601E M601E-11 M601E-11A M601E-11AS M601E-11S M601E-21 M601F M601FS M601F-11 M601F-22 M601F-32 M601T M601Z H80 H80-100 H80-200 H75-100 H75-200 H85-100 H85-200 List of effective Pages: Page 1 2 3 4 5 6 7 8 9 10 - - - - - - - Issue 5 5 5 5 5 5 5 5 5 5 - - - - - - -
TCDS E. 070 GE AVIATION CZECH M601/H80 SERIES ENGINES Page 2 Issue 05, 16 November Intentionally left blank
TCDS E.070 GE Aviation Czech M601/H80 Series Engines Page 3 Issue: 05, 16 November I. General 1. Type/ Models: M601D, M601D-1, M601D-2, M601D-11, M601D-11NZ, M601Z, M601E, M601E-21, M601E-11, M601E-11S, M601E-11A, M601E-11AS, M601T, M601F, M601F-11, M601FS, M601F-32, M601F-22, H80, H80-100, H80-200, H75-100, H75-200, H85-100, H85-200. 2. Type Certificate Holder: GE Aviation Czech s.r.o. Beranových 65, 199 02 Praha 9 Letňany Czech Republic (formerly WALTER ENGINES a.s.) EASA Design Organisation 21J.300 3. Manufacturer: GE Aviation Czech s.r.o. 4. Application Date: M601D M601D-1 M601D-2 M601D-11 M601D-11NZ M601Z M601E M601E-21 M601E-11 JUNE 29, 1990 NOV 3, 1998 NOV 3, 1998 MAY 13, 1997 MAY 13, 1997 FEB 25. FEB 29, 1988 JULY 21, MARCH 3, 1995 M601E-11S M601E-11A M601E-11AS M601T M601F M601F-11 M601FS M601F-32 M601F-22 MARCH 16, 2001 MARCH 15, 1999 MARCH 16, 2001 APR 13, 1992 APR 7, 2000 APR 14, 2004 MAY 27, 2002 JULY 20, 1995 JULY 20, Note: WALTER as holder of the Czech TC applied on 10 Dec 2004 for issue of EASA Type Certificate on basis of the Type Certificates issued by the Czech Republic. H80 H80-100 H80-200 H75-100 H75-200 H85-100 H85-200 NOV 25, 2008 OCT 26, 2011 OCT 26, 2011 JUNE 04, JUNE 04, JUNE 04, JUNE 04, 5. Reference Date for Determination of the Applicable Requirements: 25 November 2008 6. Certification Date: M601D M601D-1 M601D-2 M601D-11 M601D-11NZ M601Z M601E M601E-21 M601E-11 NOV 12, 1990 DEC 15, 1999 DEC 15, 1999 JUNE 10, 1999 JUNE 10, 1999 AUG 18, MAR 22, 1988 AUG 18, AUG 15, 1995 M601E-11S M601E-11A M601E-11A S M601T M601F M601F-11 M601FS M601F-32 M601F-22 APR 11, 2001 JAN 10, 2001 APR 11, 2001 MAY 31, 1993 JULY 14, 2000 JUNE 14, 2004 JUNE 14, 2002 DEC 18, 1996 OCT 18, H80 H80-100 H80-200 H75-100 H75-200 H85-100 H85-200 DEC 13, 2011 DEC 13, 2011 DEC 13, 2011 NOV 16, NOV 16, NOV 16, NOV 16,
TCDS E.070 GE Aviation Czech M601/H80 Series Engines Page 4 Issue: 05, 16 November EASA Type Certificate of these models had previously been covered by the Czech Republic Type Certificates: TC No.: 99-02 M601D 1, M601D 2 TC No.: 88 02 & 88 02 Supp. 1 M601E & M601E 21 TC No.: 00 03 M601F, M601F 11 TC No.: 99 04/1 M601D, M601D 1, M601D 11, M601D 11NZ, M601Z TC No.: 89 03 M601E, M601E-21, M601E-11, M601E-11S, M601E-11A, M601E 11AS, M601T, M601F, M601FS, M601F 32, M601F 22 Transfer date to EASA Type Certificate: 26 January 2005 II. Certification Basis 1. Airworthiness Standards: CS-E, Amendment 1, dated 10 December 2007 (except E515) JAR-E515 of JAR-E, Change 9 JAR-E Change 9 dated October 21, JAR-E Change 9 + OP/E/96/1 + OP/E/97/1 JAR-E Change 7 dated January 24, 1986, FAR 33 Amdt. 12 effective Sept 2, 1988 H80, H80-100, H80-200, H75-100, H75-200, H85-100, H85-200 M601D-1, M601F, M601F-11 M601D-2 M601E, M601E-21 M601D, M601D-1, M601D-11, M601D-11NZ, M601Z, M601E, M601E-21, M601E-11, M601E-11S, M601E-11A, M601E-11AS, M601T, M601F, M601FS, M601F-32, M601F-22 Note: For some models compliance was shown with JAR-E and FAR 33 2. Special Conditions: none 3. Equivalent Safety Findings: JAR-E 570(a) and FAR 31.71 (b)(6) - Oil filter warning means indicating to the pilot impending its blockage. JAR-E 560(d) and FAR 33.67 (b) - Fuel filter. JAR-E 530(e) - Fire Precautions None for H80, H80-100, H80-200, H75-100, H75-200, H85-100, H85-200 4. Deviations: None 5. Environmental Standards: Fuel Venting: CS-34.1
TCDS E.070 GE Aviation Czech M601/H80 Series Engines Page 5 Issue: 05, 16 November III. Technical Characteristics 1. Type Design Definitions: M601D: S M601D, M601D 1: S M601D 1, M601D 2: S M601 D 2, M601D 11: S M601D 11, M601E: S M601E, M601E 21: S M601E 21, M601E 11: S M601E 11, M601E 11S: S M601E 11S, M601F: S M601F, M601F 11: S M601F 11, M601F 22: S M601F 22, M601F 32: S M601F 32, M601FS: S M601FS, M601T: S M601T, M601Z: S M601Z, M601E 11A: S M601E 11A, M601E 11AS: S M601E 11AS, M601D 11NZ: S M601D 11NZ, H80: T 524/2011, H80 100: T 524/2011, H80 200: T 524/2011 H75 100: T 524/2011, H75 200: T 524/2011, H85 100: T 524/2011, H85 200: T 524/2011 2. Description: The M601 series engines are 2 spool turboprop engines with reverse flow of air and gas, two stage axial compressor, one stage centrifugal compressor, annular combustor, one stage high-pressure turbine and one stage free turbine. 3. Equipment: Approved Equipment is defined in the applicable Engine Installation Manual. 4. Dimensions (mm): Overall Length 1675 Overall Width 590 Overall Height 650 5. Weight (kg) H80-100, H75-100, H85-100 200 H80, H80-200, H75-200, H85-200 202 M601D, M601D-1, M601D-2 197 M601E, M601E-21, M601E-11, M601E-11A, M601F, M601F-11, 207 M601F-22, M601F-32, M601T M601D-11, M601D-11NZ 204 M601Z 201 M601E-11S M601E-11AS, M601FS 212
TCDS E.070 GE Aviation Czech M601/H80 Series Engines Page 6 Issue: 05, 16 November 6. Ratings (kw) Maximum Continuous at sea level Take-off (5 min) at sea level Take-off with water injection (5 min) at sea level Max. Contingency (10 min) at sea level Intermediate Contingency at sea level M601D-1 490 540 - - - M601D-2 400 450 - - - M601E 490 560 560 595 560 M601E-21 490 560 560 595 560 M601F 500 580 580 595 580 M601F-11 500 580 580 595 580 M601D 490 540 540 M601D-11 450 450 - M610D-11NZ 320 410 - M601Z 245 382 - M601E-11 490 560 M601E-11S 490 560 M601E-11A 485 526 - M601E-11AS 485 526 - M601T 490 560 - M601FS 500 580 580 M601F-32 490 560 - M601F-22 490 560 - H80 597 597 - H80-100 597 597 - H80-200 522 597 - H75-100 560 560 - H75-200 560 560 - H85-100 634 634 - H85-200 634 634 - M601E and M601E-21 models according to FAR also are certified for: Max. Take-off (5 min at sea level): 595 kw Max. Continuous at sea level: 560 kw M601F and M601FS models according to FAR also are certified for: Max. Take-off (5 min at sea level) and Max. Continuous: 580 kw H80 and H80-200 models are certified for a Continuous OEI Rating of 597kW H85-200 model is certified for a Continuous OEI Rating of 634 kw H75-200 model is certified for a Continuous OEI Rating of 595 kw See Note 1 7. Control System: Hydro mechanical fuel control system. 8. Fluids (Fuel/Oil/Additives): See applicable Operation Manual. 9. Aircraft Accessory Drives: For accessory drives specifications, including direction of rotation, drive speed ratio to engine speed, torque continuous pad rating and maximum overhung moment, refer to the applicable Engine Installation Manual. 10. Maximum Permissible Air Bleed Extraction: For all engine models, the air bleed extraction limits are specified in the applicable Engine Installation Manual. M601E-11, M601E-11A, M601E-11S, M601E-11AS, M601F, M601FS and M601F-11 can have both a highpressure air bleed system and a low-pressure air bleed system. The high-pressure air bleed system is the standard bleed system. Low-pressure bleed system can be installed as an option and this engine build configuration is indicated on the engine identification plate by the additional designation BC01.
TCDS E.070 GE Aviation Czech M601/H80 Series Engines Page 7 Issue: 05, 16 November 11. Engines with 4000 flight cycles: Number of equivalent flight cycles within TBO is extended up 4000 while hourly TBO limit is observed for the following engine models with the additional designation BC02 on the engine plate: M601D, M601E, M601E-11. IV. Operational Limits 1. Temperature Limits: 1.1 Maximum Interturbine Temperature [ C]: Maximum Continuous Take-off (5 min) Max. Contingency (10 min) Intermediate Contingency M601D-1 690 735 - - M601D-2 660 710 - - M601E 690 735 780 760 M601E-21 690 735 780 760 M601F 690 735 780 760 M601F-11 690 735 780 760 M601D 690 735 - - M601D-11 690 735 - - M601D-11NZ 650 700 - - M601Z 650 710 - - M601E-11 690 735 - - M601E-11S 690 735 - - M601E-11A 710 710 - - M601E-11AS 710 710 - - M601T 690 735 - - M601FS 690 735 - - M601F-32 710 735 - - M601F-22 710 735 - - H80 750 780 - - H80-100 750 780 - - H80-200 720 780 - - H75-100 770 780 - - H75-200 770 780 - - H85-100 770 780 - - H85-200 770 780 - - Models M601E, M601E-21, M601F and M601FS have according to FAR also been certified for Maximum Interstage Turbine Temperature of: 780 C at Max. Continuous 1.2 Oil Inlet Temperature Range [ C]: Maximum: 85 Minimum: -20 1.3 Fuel Inlet Temperature Range [ C]: Maximum : 60 Minimum: -50
TCDS E.070 GE Aviation Czech M601/H80 Series Engines Page 8 Issue: 05, 16 November 2. Maximum Permissible Rotor Speeds: Rating Engine Model Gas Generator Rotor [%] Propeller Shaft [min -1 ] Take-off M601D, M601D-1 101,5 2080 M601D-2, M601D-11NZ 99 1950 M601D-11 100 1950 M601E, M601E-11, M601E-21, M601E-11S, M601F, M601FS, M601F-11, M601F-22, M601F-32, M601T 100 2080 M601Z 99 1900 M601E-11A, M601E-11AS 98,5 2080 H80, H80-100, H80-200 101,5 2080 H75-100, H75-200, H85-100, H85-200 101,5 2080 Max. Continuous M601D, M601D-1 99 2080 Max. Contingency (10 min) Intermediate Contingency Max. Take-off (5 min) acc. to FAR Max. Continuous acc. to FAR M601D-2 96 1950 M601D-11 98,5 1950 M601E, M601E-11, M601E-11S, M601E-21, M601F, M601FS, M601F-11, M601F-22, M601F-32, M601T 97 2080 M601E-11A, M601E-11AS 98,5 2080 M601D-11NZ 95 1950 M601Z 94 1800 H80, H80-100 100,1 2080 H80-200 98,4 2080 H75-100, H75-200 101,1 2080 H85-100, H85-200 101,2 2080 M601E, M601E-21, M601F, M601F-11, M601FS M601E, M601E-21, M601F, M601F-11, M601FS 102 2080 100.5 2080 M601E, M601E-21, M601F, M601FS 102 2080 M601E, M601E-21, M601F, M601FS 100,5 2080 H80, H80-200 101,5 2080 H80-100 100,1 2080 H75-100 101,1 2080 H75-200 101,5 2080 H85-100, H85-200 101,2 2080 100% propeller shaft speed equals to 2080 rpm. Propeller shaft speed of 2080 rpm corresponds to free turbine speed of 31023 rpm. 100% gas generator rotor speed equals to 36660 rpm. For engines with installed propellers having diameter smaller than 2185 mm the propeller speed limit is 1950 rpm.
TCDS E.070 GE Aviation Czech M601/H80 Series Engines Page 9 Issue: 05, 16 November 3. Pressure Limits: 3.1 Fuel Pump Inlet Pressure (kpa): Minimum absolute pressure: 80 Maximum gauge pressure: 300 3.2 Oil Pressure Limits (kpa): Normal operating gauge pressure: 180 to 270 Minimum gauge pressure at Idle: 120 4. Installation Assumptions: The installation assumptions are quoted in the respective Engine Installation Manuals. V. Operating and Service Instructions Engine Model Installation Manual Operation Manual Maintenance Manual Service Bulletins M601D 0982051 0982424 0982051 M601D-1 0982511 0982402 0982309 M601D-2 0982511 0982415 0982309 M601D-11 0982511 0982415 0982309 M601D-11NZ 0982511 0982415 0982309 M601Z 0982511 0982521 0982309 M601E 0982502 0982404 0982055 M601E-21 0982502 0982404 0982055 M601E-11 0982504 0982406 0982302 M601E-11S 0982504 0982406 0982302 M601E-11A 0982504 0982406 0982302 M601E-11AS 0982504 0982406 0982302 M601T 0982506 0982410 0982304 M601F 0982509 0982413 0982302 M601FS 0982509 0982413 0982302 M601F-11 0982509 0982413 0982302 M601F-32 0982062 *) 0982108 *) 0982062 *) M601F-22 0982062 *) 0982108 *) 0982062 *) H80, H80-100, H80-200 0983202 0983302 0983402 H75-100, H75-200 0983202 0983302 0983402 H85-100, H85-200 0983202 0983302 0983402 Published as required *) Manuals are issued only in the Russian language version - Manual N 0982211 Technical Servicing Prescription is issued in the Russian language.
TCDS E.070 GE Aviation Czech M601/H80 Series Engines Page 10 Issue: 05, 16 November VI. Notes Note 1: Note 2: Note 3: Note 4: Note 5: Note 6: The engine ratings are based on ICAO International Standard Atmosphere sea level, static conditions: No loading of accessory drives No compressor air bleed No installation losses Certain engine parts are life-limited. These limits are published in the Maintenance Manual, Airworthiness Limitations Section. The M601 series engines meet the requirements of JAR-E 780 (CS-E780 for H80, H80-100, H80-200, H75-100, H75-200, H85-100 and H85-200) for operation in icing conditions as defined in FAR 25, Appendix C, when the intake system conforms to the approved design (Part number (P/N) B 062350). The M601 series engines meet the requirements of JAR-E 500 (CS-E500 for H80, H80-100, H80-200, H75-100, H75-200, H85-100 and H85-200) for surge free operation, when the intake system conforms to the approved design (Part number (P/N) B 062350). The M601 series engines meet the requirements of JAR-E 800 (CS-E800 for H80, H80-100, H80-200, H75-100, H75-200, H85-100 and H85-200) for bird ingestion when the intake system conforms to the approved design (Part number (P/N) B 062350). Power may be restored in hot day conditions by means of water injection when accomplished in accordance with requirements of the applicable Installation Manual and Operation Manual. This applies to M601D, M601E, M601E-21, M601E-11, M601E-11S, M601F, M601FS and M601F-11 engine models only. ----------------------------------------