DF-100 DF-165 & DF-200 w/adjustable Regulator INSTALLATION MANUAL CUMMINS POWERED DODGE TRUCKS Model Year 1994 THROUGH 1998 High Performance Demand Flow Fuel System With New Quick Connect Components PLEASE READ THIS MANUAL THOROUGHLY BEFORE BEGINNING INSTALLATION! PureFlow AirDog 705 MAUSOLEUM ROAD SHELBYVILLE, IN 46176 1-877-421-3187 www.pureflowairdog.com PROTECTED BY CANADIAN PATENT US PATENTS AUSTRALIAN PATENT 2,108,391 5,355,860; 5,746,184; 6,729,310 2005101054 NEW ZEALAND PATENT 532356 Additional Foreign Patents Pending in Europe, South America, Mexico, Japan, and China!
Approved for Sale and Use in California by CARB! (Limited Edition Model Pictured) SMALL RETURN LINE FOR AIR, VAPOR AND FOAM PRESET OR ADJUSTABLE PRESSURE REGULATOR PROTECTIVE WIRE SCREEN IN NIPPLE DEMAND FLOW SERIES FLOWS ONLY THE AMOUNT OF FUEL THE ENGINE REQUIRES SMALL and COMPACT 7 Long X 3.2 Wide X 10 Tall 2
OVERVIEW Welcome to PureFlow AirDog s AirDog II Fuel Air Separation, Filtration and Delivery System for the Diesel Engine The AirDog II Fuel Air Separation system is a Premium replacement lift pump and filtration system for the Dodge Cummins 5.9L 12 Valve diesel engine. A complete installation kit is included. The AirDog II delivers clean fuel to the engine free of virtually all air/vapor and at a positive flow. Thus, allowing the engine test cell performance and efficiency, while in real world use. The AirDog DF-100 is for stock engines. The DF-165 is recommended for highly modified 5.9L 12 Valve Cummins Diesels. The DF-200 is recommended for EXTREMELY MODIFIED Dodge Cummins 12 Valve Diesels. The AirDog II system includes a complete installation kit! PureFlow products are manufactured with a personal touch, unsurpassed attention to detail and the most stringent Quality Assurance! TYPICAL INSTALLATION LAYOUT The AirDog II draws fuel from the fuel tank at constant flow, removing water, particulates, and air/vapor. A regulated pressurized flow is maintained to meet the engine s varying fuel demands. The AirDog II returns the separated air/vapor to the fuel tank. NOTE: The pictures used in this manual are for example only and may not be exactly the same as your truck. 3
QUICK CONNECT COMPONENT OVERVIEW Provided in this kit are two different OE style quick connection systems. These systems work together to allow for a quick, clean, and professional install. Jiffy Tite Quick Connect System Jiffy Tite s patented quick connect system is used for the connections at the AirDog. The images below show the flared formation of the Jiffy Tite System. Simply insert the male end form into the fitting and push firmly until you hear it click into place. To disconnect the system, use a Jiffy Tite tool similar to the image below. This tool can be purchased at your local auto parts store. Insert the tool into the connection and turn it ¼ turn to open the retaining spring. While the retaining spring is open, firmly pull the connection apart. SAE J2044 Quick Connect System The SAE J2044 quick connect system is the most commonly used system in the automotive industry. The images below show the formation of SAE J2044 connection. To connect the assemblies, simply insert the male end form into the mating female connector. Push firmly until you hear it click into place. To disconnect the fittings, press down and hold the blue tabs on the female connector while you firmly pull the assembly apart. 4
Section 1 Table of Contents TABLE OF CONTENTS Section 1.....Table of Contents Section 2......Installation & Safety Guidelines Section 3......Parts List INSTALLATION PROCEDURES Section 4... AirDog II & Mounting Brackets Fuel Lines Section 5 A.. Fuel To Engine Section 5 B......P-7100 Fuel Return to Tank.... & Injector Fuel Bleed Return to Tank Section 5 C...DF-100 Air/Vapor Return Line Section 5 D...DF-100 Fuel Supply Line Section 5 E... DF-165 & DF-200 Fuel Supply Line Section 5 F DF-165 &DF-200 Fuel Return to Tank Electrical Harness Section 6...Electrical Harness Section 7.......Final Check List Maintenance Section 8. Filter Service Recommendations Section 9...Cleaning the Gerotor Assembly Section 10.. Adjusting the Pressure Regulator 5
Section 2 Installation & Safety Guidelines AirDog II INSTALLATION GUIDELINES! The installation of your AirDog II can be made relatively easy by following the steps outlined in this manual, and: 1. Inventory the package components completely. Notify PUREFLOW AIRDOG immediately of any parts missing or damaged. 2. Read the installation manual completely. Understand how the system operates and installation recommendations before beginning installation. 3. The installation recommendations contained herein are suggested installation guidelines only. Individual installations may vary. 4. When installing the fuel module up-grade, be sure to drill the two additional ½ fuel ports as shown! 5. When installing the AirDog II fuel lines, be sure to connect the ORIGINAL ENGINE RETURN LINE to the fuel tank as it was from the factory when the installation is complete! If any installation procedure is uncertain, contact PUREFLOW AIRDOG for technical assistance. SAFETY GUIDELINES! CAUTION! Please be sure to chock the vehicle s tires to prevent rolling. CAUTION! CAUTION! CAUTION! CAUTION! CAUTION! Please use proper supports when working beneath an elevated vehicle. Most diesel pickups have two (2) 12volt batteries. Disconnect the battery cables to both batteries before proceeding with the AirDog II installation. Vehicle frame rails should not be drilled into or welded on. Wear safety glasses when operating power tools such as drills and grinders or when using a punch or chisel. Use common sense when routing fuel lines and electrical harnesses. Keep them away from hot exhaust components and/or moving parts. Properly secure lines to prevent chaffing. NOTE: The pictures used in this manual are for example only and may not be exactly the same as your truck. 6
Section 3 Parts List AirDog II Parts List Rev. 5-1-09 QTY DESCRIPTION Part Number IMAGE 1 Installation Manual 201-1-0121 DF-100 1 AirDog II DF-165 DF-200 1 AirDog II Bracket 001-3C-0004 1 Mounting Hardware Kit, 901-61-0102-PM 1 Frame Bracket Set 010-3C-0002PC 010-3C-0001PC 1 Wiring Harness 5E-2-010 1 Bundle of Plastic Ties 5H-2-1-06/12 1 Return Fuel Filler Tube Assembly (1-3/4 OD w/2 Clamps) ( DF-100 ONLY) 001-4A-1-0175 1 Fuel Module Up Grade Kit (DF-165 & DF-200 Only) 901-01-0510 1 Spacer 010-3C-0003-A-P 1 Suction Hose Assembly ( DF-100 ONLY) WAP110-8-6 1 Suction Hose Assembly WAP110-8-8 1 Return Hose Assembly ( DF-100 ONLY) WAP112-8-8 1 Return Hose Assembly WAP112-8-6 1 Pressure Hose Assembly WAP110-8-8-90 1 14mm X ½ male SAE J2044 Fitting WAP103 1 Sealing Washer (installs on WAP103 fitting) 1P-5-ES 1 Customer Service Oring Replacement Kit 901-05-0100 3 Push Lock Hose Splice 001-4A-1-0026 2 ½ Female Jiffy Tite Quick Connect x 3/8 NPT 95182 7
1 3/8 Female Jiffy Tite Quick Connect x 1/8 NPT 85035 2 5/16 Push Lock X ¼ Male NPT 4A-1-18-05-04 1 Injection Pump Return Tee 001-4A-1-0008 1 P Pump Flexible Return Line 4C-1-02-05-001 ILLUSTRATION OF QUICK CONNECT COMPONENTS 8
Section 4 AirDog II & Mounting Brackets Installing the AirDog II & Mounting Brackets on the Truck s Frame! Figure 2 Figure 3 4-1. Assemble the AirDog mounting bracket to the frame bracket. Figure 4 Figure 5 4-2. Use the spacer block to clear lines and wiring harnesses on the frame. Adjust the assembly up or down on the frame bracket as necessary for clearance. 4-3. Install a 3/8 NPT x ½ Jiffy Tite female FUEL IN ENGINE quick connect (95182) into the ENGINE and FUEL IN ports in the AirDogII. Figure 6 4-4. Install the 1/8 NPT X 3/8 Jiffy Tite Female quick connect (85035) into the TANK port of the AirDogII. Figure 7 4-4. Attach the AirDog to the frame bracket assembly. 9 Figure 8
AirDog II Dodge 1994-1998 Section 4 AirDogII & Mounting Brackets Installing the AirDog & Mounting Brackets on the Truck s Frame, cont d! NOTE: The AirDog can be mounted on either the inside or the outside of the frame, as space or personal choice dictates. Mount The AirDog Outside The Frame Figure 9 Or Figure 10 Inside The Frame Figure 11 Figure 12 For this installation, the AirDogII is mounted inside the frame! 4-5. Clamp the frame between the AirDogII bracket assembly and the backing plate using the bolts, lock washers, and nuts included in the kit. Figure 13 4-6. Position the AirDogII on the frame as necessary for clearance. NOTE: Be sure to mount the AirDogII so the FUEL IN port is directed toward the rear of the vehicle. Figure 13A Figure 13B NOTE: Some pickup model frame rails have a bracket that is used to support the frame during the manufacturing process If this bracket is on your frame rail and obstructs the proper positioning of the AirDogII mounting bracket, you may remove part or all of it, as needed. Be very careful not to damage the frame flange! 10
Section 5-A Fuel to Engine Installing the Fuel Supply Line from the AirDog II to the P-7100! The AirDog II fuel filter is 2 micron media. When installing the AirDog II fuel system it is recommended to bypass the factory filter canister. 5A-1. Remove the 14mm banjo bolt and original factory fuel supply line at the fuel inlet port of the P-7100 injector pump and from the original fuel filter head outlet port. P-7100 Fuel Inlet Port Figure 14 Figure 15 Figure 16 5A-2. Install the 14mm x ½ male SAE J2044 (WAP 103) fitting with the seal washer supplied into the inlet port of the P-7100 (Ref. Figure 17) vacated by the original banjo fitting. Do not over tighten the fitting. It may break. Figure 17 5A-3 Insert the Jiffy Tite male quick connect end (see figure 18) of the Pressure Hose Assembly into the female quick connect fitting previously installed in the port marked ENGINE. You will hear a click when it connects. Figure 18 5A-4. Connect the other end of the Pressure Hose Assembly to the inlet fitting installed in step 5A-2. It too will click when properly connected. 5A-5 Any excess fuel hose can be addressed by routing the house in a fashion to take up the extra length, or a section of the hose can be removed. Push lock splices have been included if you choose to remove the excess hose. NOTE: It is not necessary to keep the factory filter canister in the system 11
Section 5-B P-7100 Injector Pump and Injector Fuel Bleed Return Line to Tank! NOTE: Fuel is returned from the P-7100 fuel pump and also from the injector bleed line(s). The original 12 Valve Cummins configuration returns the fuel from the P-7100 injector pump (Ref. Fig 19) directly to the fuel tank while the injector bleed line is routed to the inlet port of the fuel filter head (Ref. Fig. 21) to be recycled back to the engine. When installing the AirDog II, it is best to route the fuel from the injector bleed line back to the fuel tank as well. Figure 19 Figure 20 Figure 21 Return line from the End of steel line from P-7100 Injector Bleed Line P Pump that connects to the tank return line 5B-1. Disconnect the injector bleed line (Ref. Fig. 21) by removing the 8 mm banjo bolt. Be careful to not misplace the O ring washer that seals the banjo fitting. 5B-2. Disconnect and remove the banjo fitting and metal fuel line connecting the fuel pump to the filter head. Figure 22 5B-3. Remove the fuel filter head. 5B-4. Connect the injector bleed line banjo fitting (Ref. Fig. 24) with 8mm banjo bolt to the Return T Push Lock Coupler. Figure 23 Figure 25 Figure 24 12
Section 5-B Engine Fuel Return to Tank P-7100 Injector Pump and Injector Bleed Line Return to Tank, cont d! 5B-5. Connect the P pump metal return line (Ref. Fig. 20) to the return T push lock fitting with the flex fuel line (Ref. Fig. 25). Figure 26 Figure 27 5B-6. Connect the original fuel return line to the other end of the Return T Push Lock Coupler fitting. Figure 28 NOTE: The mechanical fuel pump must be disabled by removing the plunger. 5B-7. Remove the mechanical lift pump by removing the two bolts on each side of the pump. Remove the plunger. Be very careful, DO NOT drop the plunger into the oil pan. Block Off Plate Figure 29 Figure 30 5B-8. Either re-install the pump on the engine or cover the mechanical pump port on the engine with a Big Block Chevy pump block off plate, available from your local auto parts store. 13
AirDog II DF-100 Dodge Cummins 1994-1998 Section 5-C Fuel Lines Fuel Return Line from the AirDog to the Tank Installing the fuel 'Return to Tank' assembly in Filler Tube Hose Clamp Filler Tube Fuel Fuel Tank Figure 31 5C-1. Cut filler tube as illustrated, removing 1½ inches. Loose assemble clamps on each end of filler tube. Figure 32 Figure 33 5C-2. Insert Return Fuel Filler Tube assembly in filler tube. INSTALL THE FILLER TUBE WITH ARROWS POINTING TOWARD THE TANK!! SEE FIG 32 Properly tighten clamps. 5C-3. Insert the Jiffy Tite male quick connect end( see Figure 33) of the Return Hose Assembly into the pre installed female Jiffy Tite fitting in the port marked Tank. The fitting will click when properly installed. 5C-4 Attach the other end of the Return Hose Assembly onto the male end form of the Return Fuel Filler Tube installed in step 5C-2. A click will be heard when the fitting is properly connected. 5C-5 Any excess fuel hose can be addressed by routing the house in a fashion to take up the extra length, or a section of the hose can be removed. Push lock splices have been included if you choose to remove the excess hose. 14
AirDog II DF-100 Dodge Cummins 1994 1998 Section 5-D Fuel Lines Fuel Supply Line for AirDog II DF-100 Only! NOTE: The AirDog II DF-165 and DF-200 require a Fuel Module Up- Grade Kit. If you are installing an AirDog II DF-165, skip Section 5-D and go directly to Section 5-F for installation instructions! Connecting the Fuel Supply Line from the Tank to AirDog DF-100 Figure 34 Figure 35 5D-1. Insert the male Jiffy Tite quick connect end (see figure 36) of the Suction Hose Assembly to the female Jiffy Tite fitting previously installed in the Fuel In port. A click will be heard when the fitting is properly connected. Figure 36 5D-2. Remove the original fuel suction line Quick Connect fitting from fuel tank by squeezing the tabs on the end of the connector together. Consult factory manual if unsure. Suction Tube Quick Connect Fitting Fuel Return Tube View From Beneath Bed Figure 37 Figure 38 Figure 39 In More Detail To release the quick-connect fitting from the fuel tank suction tube, push the fitting toward the suction tube while firmly holding the plastic retainer ring into the fitting. With the plastic ring firmly depressed, pull the fitting assembly from the suction tube. Use care to hold the retainer ring square to the Quick Connect Fitting body. It may be difficult to disconnect the fitting if the retainer is cocked or becomes cocked during removal. 15
AirDogII Dodge Cummins 1994-1998 Section 5-D Fuel Lines Fuel Suction Line for AirDog DF-100, cont d 5D-2 Very Important: After removing the factory line check to make sure that the blue plastic retainer was removed with the line. If the blue retainer remained attached to the tank tube, it MUST be removed before the new fuel line Quick Connect will connect and seat to the tank suction tube. 5D-3. Attach the other end of the Suction Hose Assembly to the male quick connect on the top of the fuel module where the factory suction line was once located. A click will be heard when the assembly is properly connected. Figure 40 5D-4. Any excess fuel hose can be addressed by routing the house in a fashion to take up the extra length, or a section of the hose can be removed. Push lock splices have been included if you choose to remove the excess hose. 16
AirDog II Dodge 1994-1998 Section 5 E Fuel Lines Fuel Suction Line for AirDog II DF-165, DF-200 5E-1. Insert the male Jiffy Tite quick connect end (see figure 41) of the Suction Hose Assembly to the female Jiffy Tite fitting previously installed in the Fuel In port. A click will be heard when the fitting is properly connected. Figure 41 5E-2. 5E-3. Refer to the installation instructions within the fuel module upgrade kit. Install the fuel module up grade kit. Attach the female quick connect end of the Suction Hose Assembly to the bulk head male quick connect installed during the fuel module upgrade. (see Fig 42). A click will be heard when the fitting is properly connected. Figure 42 Note: Figure 42 is for visual reference only. The fuel module in your vehicle may appear different. 5E-4 Any excess fuel hose can be addressed by routing the house in a fashion to take up the extra length, or a section of the hose can be removed. Push lock splices have been included if you choose to remove the excess hose.. 17
AirDog II Dodge 1998 ½ - 2004 Section 5 F Fuel Return Fuel Return to Tank for AirDog II DF-165 & DF-200 5F-1 Insert the Jiffy Tite male quick connect end ( see Figure 43) of the Return Hose Assembly into the previously installed female Jiffy Tite fitting in the port marked Tank. The fitting will click when properly installed. Figure 43 5F-2. Attach the other end of the Return Hose Assembly onto the male 3/8 quick connect on the top of the fuel module that was previously vacated by the factory suction line. A click will be heard when the fitting is properly connected. Figure 44 5F-3. Any excess fuel hose can be addressed by routing the house in a fashion to take up the extra length, or a section of the hose can be removed. Push lock splices have been included if you choose to remove the excess hose. 18
Section 6 Electrical Harness The AirDog II is equipped with a relay controlled wiring harness. WIRING DIAGRAM (In Red) Figure 45 The AirDog II relay controlled wiring harness connects directly to the fuse panel. AirDog II Pump Motor Lead Pressure Sensor/Switch Lead Indicator Light Lead Battery Positive Lead Battery Negative Lead Mini Fuse Tap Relay Lead Figure 46 CAUTION: If the OPTIONAL Low Pressure Indicator Light is not used, be sure to insulate the two (2) #10 Indicator Light connectors to prevent accidental contact. Securing the Relay and Fuse Holder to the Vehicle 6-1. Secure the relay and fuse holder to the vehicle. Figure 47 Figure 48 19
Section 6 Electrical Harness Connecting the AirDog II Relay Control to the Fuse Panel 6-2. Route the red, Relay Trigger, wire with the mini fuse tap attached to the fuse panel located under the hood on the driver s side. Insert the mini fuse tap into a spare fuse holder on the panel that is hot when the starter key is turned to the on position. Figure 49 6-3. Route the pump motor lead to the AirDog II Connect the 2 pin Deutsch connector on the end of the wiring harness into the corresponding pump motor lead connector on the AirDog II. Figure 50 NOTE: The power supply leads can be connected to the battery or the alternator. Connecting the power supply leads to the alternator instead of the battery will create a corrosion free connection. Black (-) Red (+) Replace the Protective Cover Figure 51 Figure 52 6-4A. Route the Red & Black power supply leads to the alternator Connect the Black (-) lead to the alternator Chassis Ground connection. Connect the Red (+) lead to the alternator Hot Lead going to the battery. 20
Section 6 Electrical Harness Connecting the power supply leads, cont d! 6-4B. Should you choose to connect the power supply leads directly to the battery, connect the RED (+) lead to the POSITIVE (+) post of the driver's side battery. Connect the BLACK (-) lead to the NEGATIVE (-) post of the same battery. Black (-) Red (+) Figure 53 6-5. Route the wiring harness to the AirDog II and connect the 2 pin Deutsch connector to the corresponding connector on the AirDog II. Figure 54 NOTE: If the Optional Indicator Light is not used, secure the pressure switch lead to the wiring harness with a plastic tie. Also, cover the pressure sensor lead to protect it you may want to use it later. 21
Section 7 Initial Startup Procedures INITIAL START PROCEDURE The AirDog II is a self priming system, however, to prevent potential damage and reduce the life expectancy of the system, it is recommended to pre-fill the pre-filter and fuel filter with diesel fuel before initial startup. 7-1. Turn the starter key to the on/run position. Note: It may be necessary to momentarily engage the starter in order for the ECM to energize the AirDog II. 7-2. While the AirDog II is operating, bleed the fuel line to the engine of air by loosening the fuel line connection at the engine fitting. As soon as the line is purged of air and pure fuel is observed, properly tighten the fuel fitting. NOTE: put a rag or shop towel over and around fitting to prevent splatter. Catch all spilled fuel and dispose of properly. 7-3. Start engine! RECHECK ALL FUEL FITTINGS FOR LEAKAGE AND PROPER TORQUE. BE SURE ALL FUEL LINES ARE PROPERLY ROUTED TO PROTECT FROM EXCESSIVE HEAT AND SECURED TO PROTECT FROM CHAFFING AND ABRASION. RECHECK ALL ELECTRICAL LINES, SECURE AS NECESSARY. Checking Pump Noise! Note: Each AirDog II has been manufactured in a Quality Controlled process and wet tested for operation and performance before shipment. This is a very quiet and smooth running system. With fuel or air alone, the AirDog II fuel pump will run very quietly. However, if any fuel fitting on the vacuum side, between the fuel tank and the AirDog II or the pre-filter, has been left loose during the installation process, the system may suck air at an excessive rate and will be very noisy. Additionally, should the suction line be pinched or restricted, cavitation can cause vapor to form. Vapor passing through the gerotor will also cause loud noise. To check for this problem, unscrew the pre-filter 3 or 4 full turns and activate the AirDog II by turning the ignition switch to on. If the AirDog II runs quietly, then excessive air from a loose fitting, leaking pre-filter seal or vapor caused by restriction and a high vacuum is most likely the reason for the excessive noise. Correct as necessary. A. Check all fittings, especially the quick connect at the tank. B. For the AirDog II gerotor pump to operate quietly, the maximum vacuum level allowable at the fuel inlet port should be no greater than 12 hg. 22
Section 8 Fuel Filter & Pre-filter Filter Service Recommendations Plugging of either the fuel filter, the screen in the water separator nipple or the water separator itself will cause low fuel pressure and low flow to the engine. Should you experience low fuel pressure, first check the screen in the water separator nipple. If it is blocked by a film or debris, unscrew the nipple from the base, clean the screen, then reinstall the nipple. If the screen is not restricted, check the water separator for plugging and restriction, then replace as necessary! If the low fuel pressure issue continues, replace the fuel filter. AirDog 2 Micron Fuel Filter PROTECTIVE WIRE SCREEN IN THE WATER SEPERATOR NIPPLE AirDog WATER SEPARATOR The Water Separator Drain Valve Replace the water separator every other time you change the Fuel Filter or if it becomes damaged or plugged. It is suggested to check/drain the water separator every three months or as needed should you experience excessive water in fuel conditions. When installing the water separator, be sure to clean the underside of the AirDog base. Follow the instructions printed on the pre-filter for proper tightening procedures. Caution: Be extremely careful to prevent any contaminates or debris from entering the pre-filter when removing it for cleaning! Large debris will jam the Gerotor and cause the fuse to blow. This is not a warranty item. Should this happen, you can easily put the system back into working order. See the instructions on How to clean the Gerotor for proper procedures. The Fuel Filter Remove the fuel filter by turning it counter clockwise. Do Not pre-fill the fuel filter with fuel. The AirDog will fill the filter and prime the system automatically. Follow the instructions on the filter for proper tightening procedures. CAUTION: Dispose of waste fuel and used filters properly to protect OUR environment! 23
Section 9 AirDog Fuel Pump Cleaning Debris from the Gerotor Assembly Step 1 Step 2 Step 3 Remove the four (4) socket Carefully remove the O-rings, Remove and clean the gerotor. head cap crews that secure you will need to re-use it. Be very careful not to damage the gerotor cap. the gerotor. Step 4 Step 5 Step 6 Remove the O-rings and clean Replace the center gear. Align and install the outer the inside of the gerotor pocket gear and O-rings. Step 7 Step 8 1 4 3 2 Install the gerotor cap. Be very careful not to dislodge or pinch the O-rings. Loose assemble the cap screws. Torque the cap screws in an opposing pattern. 24
Section 10 Pressure Regulator AirDog II with Adjustable Pressure Regulator! The AirDog II rises to a new level of excellence with an Adjustable Regulator machined from stainless steel with a double O-ring seal system and a soft seat piston. Pressure Adjustment PRESSURE ADJUSTMENT Loosen the Jam Nut Re-Torque After Adjusting Use a Screwdriver to Adjust the Pressure Regulator To set the DF-165 Regulator at 30-35 PSI w/out using a pressure gauge, turn the regulator counter clockwise until it stops, then turn the regulator clockwise 7 full turns. ALWAYS USE A PRESSURE GAUGE WHEN ADJUSTING THE DF-100 & DF-200! Turn the adjustor screw counter clockwise to reduce the output pressure or clock wise to increase the pressure. Be sure to re-torque the Jam Nut after adjusting the regulator. Changing the Regulator Spring Step 1. Remove the regulator by turning the Base Nut/Adjustor Body counter clockwise. Step 2. After removing the regulator assembly, slide the piston from the regulator assembly and remove the spring. Step 3. Slide the new spring into position, replace the piston. Step 4. Replace the assembly in the base. Tighten the Base Nut to proper torque. Stainless Steel components with a Double O-ring Seal System and Soft Seat Piston. 25
PUREFLOW AIRDOG LIFETIME LIMITED EXPRESS WARRANTY FOR PureFlow AirDog systems FP-100, FP-150, and Raptor Fuel Pump RP-100 or RP-150 IMPORTANT NOTICE TO ACTIVATE YOUR PURFLOW AIRDOG WARRANTY, YOU MUST COMPLETE AND MAIL YOUR WARRANTY CARD TO PUREFLOW AIRDOG WITH A COPY OF YOUR ORIGINAL SALES RECEIPT WITHIN 30 DAYS OF PURCHASE. FAILURE TO COMPLETE AND SUBMIT YOUR WARRANTY CARD WILL RESULT IN A WARRANTY PERIOD OF THE COVERED PRODUCE TO ONE (1) YEAR FROM THE DATE OF PURCHASE. PureFlow AirDog (hereafter collectively, SELLER ) warrants and guarantees only to the Original Purchaser (hereafter collectively, BUYER) that the PureFlow AirDog systems FP-100, FP-150, Raptor Fuel Pump RP-100 or RP-150 (hereafter collectively, PRODUCT) shall be free from defects of materials and workmanship in the manufacturing process for as long as the BUYER owns the PRODUCT. The Lifetime Limited Express Warranty is limited to the PRODUCT purchased by the original BUYER of the PRODUCT and limited solely to the parts contained within the PRODUCT and EXCLUDES ALL ELSE INCLUDING FILTERS AND WATER SEPARATORS. Any PRODUCT that is in question of Warranty must be returned, shipped prepaid, to PureFlow AirDog. All Warranty claims are subject to the approval of PureFlow AirDog. If it is determined that a Warranty claim exists, PureFlow AirDog will, at its sole discretion, replace the defective PRODUCT with a comparable PRODUCT, repair the defective PRODUCT, or refund the BUYER S purchase price in exchange for the PRODUCT. Repairs or replacements are warranted for only the remainder of the original warranty period and only to the original BUYER. Under no circumstances shall the SELLER be liable for any labor charged or travel time incurred in the diagnosis for defects, removal, or reinstallation of the PRODUCT, or any contingent expense. Under no circumstances will the SELLER be liable for any damage or expense incurred by reason of the use or sale of the PRODUCT. Other than expressly set forth herein, the SELLER shall in no way be responsible for the proper or improper use and service of the PRODUCT. In no event shall the SELLER be liable for any special, incidental, indirect or consequential damages of any kind or nature, whether or not the BUYER of the PRODUCT was advised of the possibility of damage or harm, arising or resulting from the use or performance of the PRODUCT and BUYER hereby waives the right to any and all such claims. BUYER, acknowledges that he/she is not relying on SELLER S skill or judgment to select or furnish goods suitable for any particular purpose and that SELLER has no liability that will extend beyond the scope of the LIMITED EXPRESS WARRANTY contained herein, and BUYER hereby waives all remedies or liabilities, expressed or implied, arising by operation of law or otherwise.(including, without limitation, any obligation of SELLER with respect to fitness for any particular purpose; merchantability; and special, incidental, indirect or consequential damages) or whether or not occasioned by SELLER S negligence. SELLER disclaims any warranty and expressly disclaims any liability for personal inquiry or damages related to BUYER S use of the PRODUCT. BUYER acknowledges and agrees that the disclaimer of any liability for personal injury is a material term for this agreement and BUYER agrees to indemnify SELLER and hold SELLER harmless from any claim related to the PRODUCT and its use or performance. Under no circumstances will SELLER be liable for any damages, liabilities, costs or expenses incurred as a result of or by reason of use, performance or sale of the PRODUCT, including without limitation, any damages, liabilities, costs or expenses incurred by reason of BUYER S negligence related to those uses of the PRODUCT. The proper installation of the PRODUCT is the sole responsibility of the BUYER. The SELLER assumes no liability regarding improper installation or misapplication of the PRODUCT. 26
SELLER hereby provides the following limited warranty as to description, quality, merchantability, fitness for the PRODUCT S purpose, productiveness, or any other matter of SELLER S PRODUCT sold herewith. The SELLER shall be in no way responsible for the open use and service of the PRODUCT and the BUYER hereby waives all rights other than those expressly written herein. This Warranty shall not be extended or varied except by a written instrument signed by SELLER and BUYER. IN THE EVENT THAT THE BUYER DOES NOT AGREE WITH THIS AGREEMENT, THE BUYER MAY PROMPTLY RETURN THE PRODUCT, IN A NEW AND UNUSED CONDITION, WITH A DATED PROOF OF PURCHASE, TO THE PLACE OF PURCHASE WITHIN THIRTY (30) DAYS FROM THE DATE OF PURCHASE FOR A FULL REFUND. THE BUYER AGREES THAT THE INSTALLATION OF THIS PRODUCT CONFIRMS THE BUYER HAS READ AND UNDERSTANDS THIS AGREEMENT AND ACCEPTS THE TERMS AND CONDITIONS OF THIS AGREEMENT. Warranty Procedure In the unlikely event a warranty appears as if it may be warranted, the following steps are taken: 1 The customer discussed the symptoms of the problem with a PureFlow AirDog Technician. The customer is to have the system Serial Number and Model Number available for the Technician when the call is made. This will expedite all steps of the process. 2 The customer performs any and all tests requested by the PureFlow AirDog Technician. This is done to isolate the potential problem while eliminating potential installation or maintenance related issues, 3 If the PureFlow AirDog Technician determines based on the customer feedback concerning the requested testing that system may be at fault, the customer is advised that all returned pumps are tested upon arrival and should this returned pump perform at design criteria upon arrival, the customer will be charged a $50.00 fee. 4 The PureFlow AirDog Technician will first request the customer s phone number in the event the phone call is accidentally disconnected and then transfer the customer to a PureFlow AirDog Customer Service Representative. Should a Customer Service Representative not be available, the Technician will offer the Customer the option to hold, call back, or receive a return call. 5 The PureFlow AirDog Customer Service Representative will check to determine if the customer s Warranty Registration Card is on file. a. If no Warranty Registration is found, the customer will be required to supply the original purchase receipt showing the purchase date. b. If no Warranty Registration is found, the customer will be advised of the options should the system in question is out of the default warranty period (1 year). 6 The PureFlow AirDog Customer Service Representative will request the customer information, including: Name, Address, Phone Number, Model Number, Serial Number, Year / Make / Model of vehicle, Name of Dealer purchased from, Purchase Date, Description of Problem, Customers understanding of the resolution, and customer credit card information. 7 PureFlow AirDog will cover Ground Shipping charges to ship the replacement unit and will include a prepaid shipping label for the return of the defective unit. Any additional items ordered at the time of the replacement shipment will include their portion of the shipping cost. 8 A period of 15 Calendar Days from the time of shipment is provided for the receipt of the defective unit at the PureFlow AirDog facility. Failure to return ship the defective unit to arrive within the defined time period will result in a charge of $250.00 against the customer s credit card as the purchase cost of the defective unit. PFT Bulletin No. 201-1-0121 Revised 8-12-10 27