Technical Data Sheet BRADY B-477 THERMAL TRANSFER PRINTABLE GLOSSY WHITE STATIC DISSIPATIVE POLYIMIDE LABEL STOCK TDS No. B-477 Effective Date: 07-Jul-2010 Description: GENERAL Print Technology: Thermal Transfer Material Type: White Polyimide (2 mil film) Finish: Glossy Adhesive: Static Dissipative Permanent Acrylic APPLICATIONS Printed circuit board and electronic component preprocess labeling RECOMMENDED RIBBONS Brady Series R6000 Brady Series R6000HF (low halogen) REGULATORY/AGENCY APPROVALS UL: B-477 is a UL Recognized Component to UL969 Labeling and Marking Standard when printed with Brady Series R6000 and Series R6000HF ribbons. See UL file MH17154 for specific details. UL information can be accessed online at UL.com. Search in Certifications area. SP Provning Forskning: ESD-approved for IEC 61340-5-1 and EN 100015-1 per SP Swedish National Testing and Research Institute (see ESD-approval DNo: 230-01-0169). Brady B-477 is RoHS compliant to 2005/618/EC MCV amendment to RoHS Directive 2002/95/EC. SPECIAL FEATURES B-477 has a static dissipative adhesive and is supplied on a static dissipative release liner. It has surface resistivity values in the recommended range for Dissipative ESD Packaging Materials as defined in Table 1 of ANSI/ESD S20.20 ( 1x10 5 to < 1x10 12 ohms). B-477 also meets the requirements of EIA- 541 "Packaging Material Standards for ESD Sensitive Items" in which a charged material must decay to 1% of its initial voltage in less than 2 seconds. B-477 in combination with the Series R6000 and Series R6000HF ribbons passes the requirements of MIL-STD-202G, Notice 12, Method 215K. Details: PHYSICAL PROPERTIES TEST METHODS AVERAGE RESULTS Thickness ASTM D 1000 -Substrate -Adhesive -Total Adhesion to: -Stainless Steel Tack ASTM D 1000 20 minute dwell 24 hour dwell ASTM D2979 Polyken Probe Tack 1 second dwell Drop Shear PSTC-7 (except use 1/2" x 1" sample) 0.0025 inch (0.063 mm) 0.0017 inch (0.043 mm) 0.0042 inch (0.106 mm) 40 oz/in (44 N/100 mm) 55 oz/in (61 N/100 mm) 29 oz (800 g) >100 hours Dielectric Strength ASTM D 1000 11,000 Volts Total
Adhesive Surface Resistivity EOS/ESD S11.11 1 x 10 8 ohms/sq Liner Surface Resistivity EOS/ESD S11.11 - Release side - Backside 1.7 x 10 10 ohms/sq 2.5 x 10 9 ohms/sq Static Decay - Adhesive EIA-541 to 1% of initial charge 0.01 seconds Static Decay - Liner Voltage (Label removed from liner, adhesive tested) Voltage (Label removed from liner, liner tested) EIA-541 to 1% of initial charge - Release side 0.3 seconds Value is obtained by removing a 1.5" x 0.25" label from liner and immediately holding label to a static sensing device calibrated in volts. Value is obtained by removing a label from liner and immediately holding label to a static sensing device calibrated in volts. 4 volts 2.7 volts Samples printed with Series R6000 and Series R6000HF thermal transfer ribbons. Labels printed with 3:1 ratio bar codes with 6 mil X dimension bars. Samples laminated to aluminum panels. All samples allowed to dwell 24 hours prior to testing. Samples exposed to the indicated environments. PERFORMANCE PROPERTIES TEST METHOD TYPICAL RESULTS Short Term High Service Temperature Long Term High Service Temperature 80 seconds at 572 F (300 C) to label at 572 F (300 C), label discolors slightly at 626 F (330 C), but still functional, at 662 F (350 C) label still functional but moderately discolored and adhesive discolored at label edge; print is still legible. 5 minutes at 500 F (250 C) to label at 500 F (260 C), label discolors slightly at 518 F (270 C), at 572 F (300 C) label moderately discolors and adhesive discolors at label edge. Label remains functional. 2 hours at 338 F (170 C) to label at 338 F (170 C), label discolors slightly at 374 F (190 C), moderately at 428 F (220 C) and severely at 500 F (260 C). Label remains functional. 1000 hours at 212 F (100 C) to label at 212 F (100 C), label discolors slightly at 248 F (120 C), moderately at 293 F (145 C). Label remains functional. Low Service Temperature 1000 hours at -94 F (-70 C) Humidity Resistance 1000 hours at 100 F (37 C)/95% RH UV Light Resistance 1000 hours in UV Sunlighter TM Topcoat turns light yellow, label 100 remains functional Weatherability ASTM G155, Cycle 1 1000 hours in Xenon Arc Slight discoloration Weatherometer Salt Fog Resistance ASTM B117 30 days in 5% salt fog solution chamber Abrasion Resistance Taber Abraser, CS-10 grinding wheels, 500 g/arm (Fed. Std. Print legible to 100 cycles 191A, Method 5306) Vapor Phase Resistance Label adhered to epoxy PC board R6000 - without and exposed to: rub, moderate to total print smear
2 minutes in Fluorinert TM FC- with rub. R6000HF - Not Tested 5312 vapor phase at 420 F (216 C) *B-477 is not recommended for outdoor use. PERFORMANCE PROPERTY CHEMICAL RESISTANCE Samples printed with Series R6000 and Series R6000HF thermal transfer ribbon. Labels printed with 3:1 ratio barcodes with 6 mil X dimension bars. Samples exposed to indicated environments. TEST ENVIRONMENT CHEMICAL RESISTANCE LABEL EFFECT R6000 R6000HF Kyzen Corp. Aquanox 1 1 SSA 30% aqueous, 40-45 C - 10 minutes Isopropyl Alcohol 99%, 1-2 1-2 82 C 10 minutes BIOACT EC-7R 1-2 1-2 Terpene Cleaner, 40-45 C - 10 minutes Deionized Water, 100 C 1 1-10 minutes Alpha Metals Inc. 2110 2 2-3 Saponifier 6% aqueous, 65-70 C - 10 minutes Lenuim ES Vapor 4 4 phase 10 minutes Rating scale: 1 no visible effect 2 slight smear or print removal, detectable but minimal smear 3 moderate smear or print removal (print still legible) 4 severe smear or print removal (print illegible or just barely legible) 5 complete print removal PERFORMANCE PROPERTY Chemical Resistance TEST METHOD MIL-STD-202G, Notice 12, Method 215K Samples printed with Series R6000 and Series R6000HF thermal transfer ribbons. Labels printed with alphanumerics and 3:1 ratio barcodes with 6 mil X dimension bars. Samples subjected to 3 cycles of 3 minute immersions immediately followed by a toothbrush rub after each immersion. TEST FLUID TYPICAL RESULTS Solvent A 1 part IPA, 3 parts Mineral Spirits Solvent B 1,1,1-Trichloroethane Solvent deleted per Notice 12 Solvent C Terpene Defluxer Solvent D Saponifier at 70 C Product testing, customer feedback, and history of similar products, support a customer performance expectation of at least one year from the date of receipt for this product as long as this product is stored in its original packaging in an environment below 80 degrees F (27 C) and 60% RH. We are confident that our product will perform well beyond this time frame. However, it remains the responsibility of the user to assess the risk of using such product. We encourage customers to develop functional testing protocols that will qualify a product's fitness for use, in their actual applications.
Trademarks: Aquanox SSA is a trademark of Kyzen Corporation. BIOACT is a registered trademark of Petroferm, Inc. BradyPrinter is a trademark of Brady Worldwide, Inc. EC-7R is a trademark of Petroferm Inc. Intermec is a registered trademark of the Intermec Corporation. Polyken is a trademark of Testing Machines Inc. RE-ENTRY is a registered trademark of Environsolv Inc. AISI: American Iron and Steel Institute (U.S.A.) ASTM: American Society for Testing and Materials (U.S.A.) EIA: Electronic Industries Association (U.S.A.) EOS/ESD: Electrical Overstress/Electrostatic Discharge (U.S.A.) PSTC: Pressure Sensitive Tape Council (U.S.A.) UL: Underwriters Laboratories Inc. (U.S.A.) All S.I. Units (metric) are mathematically derived from the U.S. Conventional Units. Note: All values shown are averages and should not be used for specification purposes. Test data and test results contained in this document are for general information only and shall not be relied upon by Brady customers for designs and specifications, or be relied on as meeting specified performance criteria. Customers desiring to develop specifications or performance criteria for specific product applications should contact Brady for further information. Product compliance information is based upon information provided by suppliers of the raw materials used by Brady to manufacture this product or based on results of testing using recognized analytical methods performed by a third party, independent laboratory. As such, Brady makes no independent representations or warranties, express or implied, and assumes no liability in connection with the use of this information. WARRANTY Brady products are sold with the understanding that the buyers will test them in actual use and determine for themselves their adaptability to their intended uses. Brady warrants to the buyers that its products are free from defects in material and workmanship, but limits its obligation under this warranty to replacement of the product shown to Brady's satisfaction to have been defective at the time Brady sold it. This warranty does not extend to any persons obtaining the product from the buyers. This warranty is in lieu of any other warranty, express or implied, including, but not limited to, any implied warranty of merchantability or fitness for a particular purpose, and of any other obligations or liability on Brady's part. Under no circumstances will Brady be liable for any loss, damage, expense, or consequential damages of any kind arising in connection with the use, or inability to use, Brady's products.
Specification Of Thermal Transfer Printable Labels Application(s): Circuit Board & Component ID, SMT - Top/Bottom, Static Dissipative, Through Hole - Bottom, Through Hole - Top Agency Approval(s)/Compliance: EIA-541 "Packaging Material Standards for ESD Sensitive Items", MIL-STD- 202F, Notice 12, Method 215JESD-approved for IEC 61340-5-1 and EN 100015-1, UL Recognized Size: 0.500" W x 0.275" H (12.700 mm W x 6.990 mm H) Printable Area: 0.500" W x 0.275" H (12.700 mm W x 6.990 mm H) Web Width: 2.500" (63.50 mm) Label Type/Style: Label Vertical Repeat: 0.375" (9.53 mm) Horizontal Repeat: 0.600" (15.24 mm) Color: White Finish: Gloss Qty Per Row: 4 Material Type: Polyimide Material Description: Static Dissipative Polyimide Brady Material #: B-477 General ID Catalog: pg. 21 Recommended Ribbon Series: Suggested Ribbon Part#: 6002 R6002 After Process: Yes, this material will work with this application Printer Compatibility: BBP81, Brady 1244, Brady 1344, Brady 200MVP Plus, Brady 2461, Brady 300MVP Plus, Brady 300X-Plus II, Brady 3481, Brady 360X-Plus II, Brady 600X- Plus II, Brady 6441, Brady IP, Tagus T200, Tagus T300, Thermal Transfer Printers Surface Mount Technology: Through Hole Technology: Yes, this material will work with this application Top: Yes, Bottom: Yes Special Properties: Static dissipative adhesive & liner RoHS Compatibility: Compliant with RoHS Directive. NOTE: All statements concerning RoHS Directive compliance refer to 2005/618/EC MCV amendment to RoHS Directive 2002/95/EC. Product compliance is based upon information provided by suppliers of the raw materials used by Brady to manufacture these products, or by independent laboratory testing of these products. As such, Brady makes no independent representations or warranties, express or implied, and assumes no liability in connection with the use of this information. QTY/UOM: 10,000/Roll