PlenaForm Systems MSDS PlenaForm Systems PlenaForm, PlenaFill, PlenaVertical COMPUSPACE LC TileFlow Japan 4-13-2 03-6805-7750 Fax 03-6805-7760 PlenaForm Systems ITW Formex GK-40 PlenaForm Systems Formex GK MSDS PlenaForm Systems PlenaForm Systems PlenaForm Systems FORMEX GK MSDS FORMEX GK - XX XX - PlenaForm Systems Formex GK-40 t=1.02 OSHA PEL OSHA ACGIH TLV ACGIH AMERICAN CONFERENCE INDUSTRIAL HYGIENISTS TFJ-CSL-20130524 PlenaForm, PlenaFill CompuSpace LC
PlenaForm Systems MSDS NA NA H2O =1 1.035 =1 NA H2O. NIOSH( ) UL 94V-0 VTM-0 UL94-V0 VTM-0 UL TFJ-CSL-20130524 PlenaForm, PlenaFill CompuSpace LC
PlenaForm Systems MSDS D.O.T. D.O.T. D.O.T. Section 313 of the Emergency Planning and Community Right-to-Know Act of 1986 and of 40 CFR Part 372 CAS# 1309-64-4 6.1% - ITW/Formex ITW/Formex ITW/Formex May 30, 2001 Rev4/23/03 ITW Formex 1701West Armitage Court Addison, IL 60101 USA Tel: 630.889.8655 Fax: 630.889.8713 Website: www.itwformex.com TFJ-CSL-20130524 PlenaForm, PlenaFill CompuSpace LC
ITW Formex 1701 West Armitage Court Addison, IL 60101 Telephone: 630.889.8655 Fax: 630.889.8713 Website: www.itwformex.com FORMEX GK MATERIAL SAFETY DATA Flame Retardant Materials IDENTIFICATION PRODUCT: CHEMICAL NAME: CHEMICAL FAMILY: FORMEX GK-XX (XX denotes nominal thickness in mils) Proprietary Blend Flame Retardant Polyolefin Compound HEALTH INFORMATION EYE CONTACT: SKIN CONTACT: INHALATION: INGESTION: Mechanical irritation due to small pieces. Unlikely to cause irritation. Mechanical irritation due to small pieces. Not a probable route of exposure. OCCUPATIONAL EXPOSURE LIMITS No OSHA PEL or ACGIH TLV has been established. EMERGENCY FIRST AID PROCEDURES EYE CONTACT: SKIN CONTACT: INHALATION: INGESTION: Flush eyes with water; do not rub eyes. If contact with molten material occurs, cool rapidly with cold water. Do not attempt to peel polymer from skin. Obtain medical advice for thermal burn. Breathe clean air. Not a probable route of exposure. If irritation of eyes or skin persists, obtain medical advice. PHYSICAL DATA BOILING POINT ( o F): NA VAPOR PRESSURE (mm Hg): NA SPECIFIC GRAVITY (H2O=1): 1.035 VAPOR DENSITY (air=1): NA SOLUBILITY IN H2O: Insoluble APPEARANCE AND ODOR: Solid sheet, essentially odorless. FIRE AND EXPLOSION HAZARDS EXTINGUISHING MEDIA: Water, foam, dry chemicals, or carbon dioxide. SPECIAL FIRE FIGHTING PROCEDURES: Material will not burn unless preheated. Do not enter confined fire space without a positive pressure NIOSH approved self-contained breathing apparatus with a full facepiece. Cool fire exposed containers with water. UNUSUAL FIRE AND EXPLOSION HAZARDS: Material is a UL recognized 94V-O or VTM-O product. Continued
FORMEX GK.MSDS (Continued) REACTIVITY STABILITY: Stable CONDITIONS AND MATERIALS TO AVOID: Strong oxidizing agents. EMPLOYEE PROTECTION RESPIRATORY PROTECTION: Not ordinarily required. PROTECTIVE CLOTHING: Not ordinarily required. ADDITIONAL PROTECTIVE MEASURES: Avoid prolonged exposure to vapors from molten or near molten product. Provide adequate ventilation when processing under these conditions. ENVIRONMENTAL PROTECTION SPILL OR LEAK PROCEDURES: Shovel, sweep, or vacuum to prevent slipping hazards. Contain material for reclamation or disposal. WASTE DISPOSAL: Incineration or landfill in compliance with Federal, State and Local regulations. REGULATORY CONTROLS D.O.T. CLASSIFICATION: Not hazardous by D.O.T. regulations. This product contains the following toxic chemicals subject to the reporting requirements of Section 313 of the Emergency Planning and Community Right-to-Know Act of 1986 and of 40 CFR Part 372. CAS# Chemical Name Percent by Weight 1309-64-4 Antimony Oxide 6.1% The information contained herein is based on the data available to us and is believed to be correct. However, Formex makes no warranty express or implied regarding the accuracy of these data or the results to be obtained from the use thereof. Formex assumes no responsibility for injury from the use of the product described herein. May 30, 2001 Rev4/23/03 MSDSforFormex GK.pdf