SSI-USB Brief English Version Seite 1/6 SSI-USB Flexible Embedded Platform Brief English Version Hardware v1.0 Dokument: 1401171103
SSI-USB Brief English Version Seite 2/6 1 Preface The SSI-USB-module offers flexibly programmable interfaces. The module connects to a host computer via USB or 3V3-RS232. The module implements an encoder-interface to the application complex via three RS485- transceivers. Using dedicated firmware-options, different interfaces can be represented, e.g. SSI, ABZ, RS485. Usually the module is powered via USB, alternatively via the 3V3-RS232 or the encoder-interface. 2 Applications 2.1.1 User specific funktions User specific functions become possible through a powerful embedded controller. We re looking forward to your inquiries. Standard applications are: 2.1.2 SSI Encoder-Simulator - USB-/3V3-RS232 to SSI converter - Hardware requirements o SSI-USB-v1.0 o 3V3-RS232: SSI-USB-v1.0-o1 - Communications protocol according to IB Kirchen SSI-Encoder-Simulator o Refer to Bedienungs- und Programmieranleitung für den SSI-Encoder-Simulator 4) Serielle Schnittstelle o Possible data rate is e.g.. 32bit 2MHz 2.1.3 ABZ Encoder-Simulator - USB-/3V3-RS232 to ABZ converter - Hardwarevoraussetzungen o SSI-USB-v1.0-o2 o 3V3-RS232: SSI-USB-v1.0-o1-o2 2.1.4 SSI to USB-Seriell-Converter - SSI to USB-/3V3-RS232 converter - Hardware requirements o USB: SSI-USB-v1.0 o 3V3-RS232: SSI-USB-v1.0-o1 2.1.5 USB-/3V3-RS232 to RS485 converter - USB-/3V3-RS232 nach RS485 converter - Hardware requirements o SSI-USB-v1.0-o2 o 3V3-RS232: SSI-USB-v1.0-o1-o2
SSI-USB Brief English Version Seite 3/6 3 Hardware specifications 3.1 Setup - measurements o plastic case (optional) measures ca. 87mm x 57mm x 39mm o PCB 68mm x 43,8mm o Components heights: bottom < 5mm / top < 15mm / LP < 2mm o Mounting holes Drill 3.5mm Outer copper diameter 8mm
SSI-USB Brief English Version Seite 4/6 3.2 Interfaces on PCB 3.2.1 Encoderinterface X101 - RJ45 8p8c, shielded, Typ CAT5, Amphenol RJHSE-5381 o 1: DATA+ / A+ o 2: DATA- / A- o 3: CLOCK+ / B+ o 4: Z+ o 5: Z- o 6: CLOCK- / B- o 7: Power Input 4.1V.. 5V.. 5.3V Polarity guard via diode o 8: GND o Shield : may be connected to GND on PCB via solder-jumpers Drawing 1 - http://en.wikipedia.org/wiki/modular_connector - LEDs at the Encoderinterface o LED Alive green Blinking during operation at 0,5Hz o LED Activity orange application specific behaviour - Transceivers o ADM3485(E)ARZ 3.3 V Versorgung 5 V logic compatible EIA RS-422 and RS-485 conform over full common mode range Data rate: 10 Mbps Half- and Full-Duplex options Reduced slew rate for reduced EM-emission available ADM3483, reduced data rate 250kbps Up to 32 transceivers on the bus CAVEAT: adhere to power and terminator limitations 7 V to +12 V bus common mode range 8 ns delay through ADM3485 3.2.2 3V3-RS232 X103 - Option o1 - RS232 Interface o RJ10 4p4c 1: VSUP_RJ11 2: TX 3V3-RS232 - Output 3: RX 3V3-RS232 - Input 4: GND - VSUP_RJ10 is connected to the internal power regulator via a choke. Application: o If powered over USB or Encoderinterface this voltage can supply an external level converter (e.g. IBK 01009-11) o The user may feed an external voltage of 5..9V into the module
SSI-USB Brief English Version Seite 5/6 3.2.3 USB X102 - USB-interface o Standard USB-B o This is the standard power supply for the module o Power requirements depend on application, between 30..200mA, diode for reverse feed protection o Communications interface to the host
SSI-USB Brief English Version Seite 6/6 3.2.4 Equipotential bonding - The four fixation holes are connected to GND - The encoder interface shield con be connected to GND - CAVEAT o To stay within the RS485-transceiver s common-mode-range, equipotential equalization between module and signal source is mandatory 3.2.5 JTAG X203 - The JTAG-interface connects the MCU to the programmer (production and advanced usage only). o 1: MCU-Reset o 2: JTAG-Reset o 3: TMS o 4: VTARGET o 5: TDO o 6: GND o 7: TDI o 8: GND o 9: TCK o 10: GND 3.2.6 BOOT0 - X202 - If pins 1&2 of X202 are shorted on power-up, the MCU enters bootloader-mode. The user may than initiate a Device Firmware Update. o 1: BOOT0 o 2: +3V3 3.2.7 DEBUG - X201 - The DEBUG-interface connects an adapter to the Debug-RS232-interface (production and advanced usage only). o 1: RX RS232-Pegel-Eingang o 2: GND o 3: TX RS232-Pegel-Ausgang 3.3 Hardware-Options - Standard o 2 RS485-Transceiver e.g. SSI DATA+ / A+ DATA- / A- I+ / CLOCK I- / CLOCK o USB-B-interface - Option o1 o 3V3-RS232 - Option o2 o third RS485-Transceiver e.g. for ABZ-Betrieb B+ B- - Option o3: o EEPROM for user data storage