A NOV.27, 08 1 / 25 Thin-Film-Transistor LCD With Touch Panel Acceptance Solomon Goldentek Display Corp. 168,Fu Xiang Blvd,Di Yong Industrial Zone, Gao Bu,Dong Guan,Guang Dong 523273,China FAX: +86-769-8873-7947 Approved and Checked by Approved by Checked by Made by
A NOV.27, 08 2 / 25 Date Contents Written Approved A 2008/11/27 Preliminary Specification Yan Heping Special Notes Note1. Note2. Note3. Note4. Note5.
A NOV.27, 08 3 / 25 Contents 1 General Description and Features... 4 1.1 Features... 4 1.2 LCD Module... 4 2 Mechanical Information... 5 3 Electrical Specifications... 6 3.1 Absolute Ratings of Environment... 6 3.2 Electrical Absolute Maximum Ratings... 6 3.3 Display On/Off Sequence :... 7 4 Electrical Characteristics... 8 4.1 DC Electrical Characteristics of the TFT LCD... 8 4.2 Timing Condition (DE only mode)... 9 4.3 Back-Light Unit...11 5 Optical Characteristics... 12 5.1 Optical characteristic of the LCD... 12 6 Input Terminal Pin Assignment... 15 6.1 Pin Assignment CN1... 15 6.2 Touch Panel Unit... 16 6.3 Back-light Unit (BLU)... 16 6.4 Block Diagram... 17 7 Touch Screen Panel Specifications... 18 7.1 electrical Characteristics... 18 7.2 Mechanical & Reliability Characteristics... 18 8 Reliability Test... 19 9 Precautions... 21 9.1 Operation... 21 9.2 Safety... 21 9.3 Handling... 21 9.4 Static Electricity... 23 9.5 Storage... 23 9.6 Cleaning... 23 9.7 Waste... 23 10 Warranty... 24 11 Dimensional Outlines... 25
A NOV.27, 08 4 / 25 1 General Description and Features GATW80SP8K1R0 is a transmissive type color active matrix TFT (Thin Film Transistor) liquid crystal display (LCD) that uses amorphous silicon TFT as a switching device. This model is composed of a TFT-LCD module, a driver circuit and back-light unit. Graphics and texts can be displayed on a WVGA 800 (W) x 3 x 480 (H) dots (16:9 aspect ratio). The following table described the features of GATW80SP8K1R0. 1.1 Features Transmissive and back-light with 18 LEDs are available. TN (Twisted Nematic) mode. 6 bits RGB interface 4-wires analog resistive type touch panel. 1.2 LCD Module Item Specification Unit Screen Size 8.0 inches Diagonal Display Resolution 800 (H) x 480 (V) Pixel Active Area (TFT) 176.64(H) x 99.36(V) mm Outline Dimension 192.8 x 116.9 x 10.96 (Typ.) mm Display Mode Normally white mode/ Transmissive -- Pixel Arrangement R,G,B Vertical Stripe -- Pixel Size 0.2208(H)x0.2070(V) mm Display Color Full Colors -- Viewing Direction 6 o clock -- Surface treatment Anti-glare Input Interface 6 bits RGB interface --
A NOV.27, 08 5 / 25 2 Mechanical Information Item Min. Typ. Max. Unit Horizontal(H) 192.5 192.8 193.1 mm Module Vertical(V) 116.6 116.9 117.2 mm Size Depth(D) 10.66 10.96 11.26 mm Weight --- --- --- g
A NOV.27, 08 6 / 25 3 Electrical Specifications 3.1 Absolute Ratings of Environment If the operating condition exceeds the following absolute maximum ratings, the TFT LCD module may be damaged permanently. (Ta=25±2 C, V SS =GND=0) Item Symbol Min. Max. Unit Note Storage temperature T STG -30 80 C - Operating temperature T OPR -20 70 C - 3.2 Electrical Absolute Maximum Ratings (V SS =GND=0) Parameter Symbol Min. Max. Unit Remark Power supply voltage V CC -0.3 5.0 V Signal input voltage R0-R5,G0-G5 B0-B5,DCLK,DE -0.3 Vcc+0.3 V --
A NOV.27, 08 7 / 25 3.3 Display On/Off Sequence :
A NOV.27, 08 8 / 25 4 Electrical Characteristics 4.1 DC Electrical Characteristics of the TFT LCD (Ta=25±2 C, V SS =GND=0) Item Symbol Min. Typ. Max. Unit Remark Supply Voltage VCC 2.7 3.0 3.5 V Input Voltage for logic VIH 0.7VCC - VCC V Note 1 VIL 0-0.3VCC V Current of Power Supply Icc - TBD - ma VCC=3.0V Note: Be sure to apply the power voltage as the power sequence spec.
A NOV.27, 08 9 / 25 4.2 Timing Condition (DE only mode)
A NOV.27, 08 10 / 25 4.2.1 Timing Characteristic
A NOV.27, 08 11 / 25 4.3 Back-Light Unit The Back-light system is an edge-lighting type with 18 white LED (Light Emitting Diode)s. The characteristics of 18 white LEDs are shown in the following tables. (Ta= Room Temp) Characteristics Symbol Min. Typ. Max. Unit Note LED Current IL - 120 - ma (1) LED Voltage VL 9.9 12 V Power Consumption P BL - 1188 mw (2) Note (1) LEDS in 3 series x 6 parallel type. (2) Where IL = 120mA, VL = 9.9, P BL = VL IL
A NOV.27, 08 12 / 25 5 Optical Characteristics 5.1 Optical characteristic of the LCD The following items are measured under stable conditions. The optical characteristics should be measured in a dark room or equivalent state Measuring quipment: BM-7A Item Symbol Condition Min Type Max Unit Note Brightness 128 160 -- cd/m 2 Response time Contrast ratio T r - 5 7 ms θ=0 -- 20 28 ms T f CR At optimized viewing angle 400 500 -- --. Color Chromaticity (CIE 1931) White Wx 0.260 0.310 0.360 θ=0 Normal Viewing Angle Wy 0.280 0.330 0.380 Viewing Angle (6H) Hor. Ver. θ R 60 70 -- θ L 60 70 -- CR 10 φ H 40 50 -- φ L 50 60 -- Degree a. Test equipment setup After stabilizing and leaving the panel alone shall be warmed up for the stable operation of LCM, the measurement should be executed. Measurement should be executed in a stable, windless, and dark room. Optical specifications are measured by Topcon BM-7A(fast) with a viewing angle of 2 at a distance of 50cm and normal direction. b. Definition of response time: Tr and Tf The response time is defined as the following figure and shall be measured by switching the input signal for black and white.
A NOV.27, 08 13 / 25 c. Definition of contrast ratio: Contrast Ratio (CR) = Brightness measured when LCD is at white state Brightness measured when LCD is at black state d. Measured at the center area of the panel when all the input terminals of LCD panel are electrically opened. e. View Angle
A NOV.27, 08 14 / 25 f. Definition of Luminance of White: Luminance of white at the center points Light Source of Back-Light Unit LED Type g. Definition of White Uniformity Min. luminance of white among 9-points White Uniformity = X100% Max. luminance of white among 9-points h. The definition of Color Gamut -Color Chromaticity CIE 1931 Color coordinate of white & red, green, blue at center point. Color Gamut : NTSC(%) = ( RGB Triangle Area / NTSC Triangle Area ) x 100
A NOV.27, 08 15 / 25 6 Input Terminal Pin Assignment 6.1 Pin Assignment CN1 Terminal no. Symbol I/O Function 1 GND P 2 GND P Ground 3 NC -- No connection 4 VCC P 5 VCC P 6 VCC P Power supply 3V 7 VCC P 8 VCC P 9 DE I Data Enable signal 10 GND P 11 GND P Ground 12 GND P 13 B5 I Data Input 14 B4 I Data Input 15 B3 I Data Input 16 GND P Ground 17 B2 I Data Input 18 B1 I Data Input 19 B0 I Data Input 20 GND P Ground 21 G5 I Data Input 22 G4 I Data Input 23 G3 I Data Input 24 GND P Ground 25 G2 I Data Input 26 G1 I Data Input 27 G0 I Data Input 28 GND P Ground 29 R5 I Data Input 30 R4 I Data Input 31 R3 I Data Input 32 GND P Ground 33 R2 I Data Input 34 R1 I Data Input 35 R0 I Data Input 36 GND P Ground
A NOV.27, 08 16 / 25 37 GND P Ground 38 DCLK I Dot Clock input 39 GND P Ground 40 GND P Ground I: Input, O: Output, P: Power Remarks: 1) NC Pin must be retained; this pin can t contact GND or other signal. GND Pin must ground contact, can not be floating. 6.2 Touch Panel Unit Pin Symbol Function Remark 1 Y2 Touch Panel Up 2 X2 Touch Panel Right 3 Y1 Touch Panel Down 4 X1 Touch Panel Left 6.3 Back-light Unit (BLU) Pin Symbol Function Remark 1 LEDA Power Supply for LED backlight BLACK 2 LEDK GND for LED backlight WHITE
A NOV.27, 08 17 / 25 6.4 Block Diagram 6
A NOV.27, 08 18 / 25 7 Touch Screen Panel Specifications 7.1 electrical Characteristics Item Min. Typ. Max. Unit Note Linearity -1.5-1.5 % Analog X and Y directions Terminal resistance 300-1400 Ω X(Glass side) 150-800 Ω Y(Film side) Insulation resistance 20 - - MΩ DC 25V Voltage - - 7.0 V DC Response time - 15 - ms Transparency - 80 - % Non-glare Caution (1) : Do not operate it with a thing except a polyacetal pen (tip R0.8mm or less) or a finger, especially those with hard or sharp tips such as a ball point pen or a mechanical pencil. 7.2 Mechanical & Reliability Characteristics Item Min. Typ. Max. Unit Note Activation force - 80 g (1) Hitting Durability 1,000,000 - - times (2) Sliding Durability 100,000 times Surface hardness 3 - - H JIS K5400 Note (1) Input : Finger or polyacetal pen 0.8R Note (2) Pit 1,000,000 times on the Film with a R8.0 (Hardness 60 ) silicon rubber. - Force : Force : 200g - Frequency : 3 times/sec
A NOV.27, 08 19 / 25 8 Reliability Test No change on display and in operation under the following test condition. Condition: Unless otherwise specified, tests will be conducted under the following condition. Temperature: 20±5 C. Humidity: 65±5%RH. Tests will be not conducted under functioning state. Parameter Condition Notes 1 High Temperature Operating 2 Low Temperature Operating 3 High Temperature Storage 4 Low Temperature Storage 70 C±2 C, 240hrs (Operation state). -20 C±2 C, 240hrs (Operation state). 80 C±2 C, 240hrs. -30 C±2 C, 240hrs. 5 Electrostatic Discharge ±200V,200pF(0Ω) 1 time/each terminal 6 Damp Proof Test 60 C±2 C, 90%, 240hrs. 7 Vibration Test 1.Random: 1.04Grms, 5~500Hz, X/Y/Z,30min/each direction 2. Sine: Freq. Range: 8~33.3Hz Stoke: 1.3mm Sweep: 2.9G, 33.3~400Hz X/Z: 2hr, Y: 4hr, cyc: 15min 8 Drop Test To be measured after dropping from 60cm high on the concrete surface in packing state.
A NOV.27, 08 20 / 25 Dropping method corner dropping: A corner: Once edge dropping. B, C, D edge: Once face dropping. E, F, G face: Once. Notes: 1. No dew condensation to be observed. 2. The function test shall be conducted after 4 hours storage at the normal temperature and humidity after removed from the test chamber. 3. Vibration test will be conducted to the product itself without putting I in a container.
A NOV.27, 08 21 / 25 9 Precautions 9.1 Operation Burn-in sometimes happens when the same character was displayed at along time. Therefore, to prevent Burn-in, it is recommended to set up a Screen-saver function. 9.2 Safety The liquid crystal in the LCD is poisonous, DO NOT put it in your mouth. If the liquid crystal touches your skin or clothes, wash it off immediately using soap and water. 9.3 Handling a. The LCD module shall be installed flat, without twisting or bending. b. COF or FPC has narrow pattern width, so easily become open circuit by external force. DO NOT apply pressure to COF or FPC especially in bending area. c. To avoid damage in appearance or malfunction, DO NOT subject the module to mechanical shock or to excessive force on its surface. d. The polarizer attached to the display is very easy to damage, handle it with care to avoid scratching. e. To avoid contamination on the display surface, DO NOT touch the display surface with bare hands. f. Provide a space so that the LCD module does not come into contact with other components.
A NOV.27, 08 22 / 25 g. To protect the LCD panel from external pressure, put covering glass (acrylic board or similar board) to keep appropriate space between them. h. Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer or electrical contacted parts. And after fading condensation, smear or spot will occur. i. Property of semiconductor devices may be affected when they are exposed to light possibly resulting in malfunctioning of the ICs. To prevent such malfunctioning of the ICs, your design and mounting layout done are so that the IC is not exposed to light in actual use. j. Strong light exposure causes degradation of color filter. It may not recover k. DO NOT contact with water to avoid Metal corrosion. l. When it is not in use, the screen must be turned off or the pattern must be frequently changed by a screen saver. If it displays the same pattern for a long period of time, brightness down/image sticking may develop due to the LCD structure. m. Never disassemble LCD product under any circumstances. If unqualified operators or users assemble the product after disassembling it, it may not function or its operation may be seriously affected.
A NOV.27, 08 23 / 25 9.4 Static Electricity Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. 9.5 Storage a. The LCD module shall be installed flat, without twisting or bending. Ground soldering iron tips, tools and testers when they operate. b. Ground your body when handling the products. c. DO NOT apply voltage to the input terminal without applying power supply. d. DO NOT apply voltage that exceeds the absolute maximum rating. e. Store the products in an anti-electrostatic container. f. Peel off protect tape, attached to polarizer, slowly to minimize ESD damage. Store the products in a dark place at +5 ~ +25 degree C, low humidity (50%RH or less). DO NOT store the products in an atmosphere containing organic solvents or corrosive gases. 9.6 Cleaning a. DO NOT wipe the polarizer with dry cloth, as it might cause scratch. b. Wipe the polarizer with a soft cloth soaked with petroleum IPA, other chemical might damage. 9.7 Waste When dispose of LCD module, manage it at the production waste according to the relevant laws and regulations.
A NOV.27, 08 24 / 25 10 Warranty This product has been manufactured to your company s specifications as a part for use in your company s general electronic products. It is guaranteed to perform according to delivery specifications. For any other use apart from general electronic equipment, we cannot take responsibility if the product is used in medical devices, nuclear power control equipment, aerospace equipment, fire and security systems, or any other applications in which there is a direct risk to human life and where extremely high levels of reliability are required. If the product is to be used in any of the above applications, we will need to enter into a separate product liability agreement. 1 We cannot accept responsibility for any defect, which may arise from additional manufacturing of the product (including disassembly and reassembly), after product delivery. 2 We cannot accept responsibility for any defect, which may arise after the application of strong external force to the product. 3 We cannot accept responsibility for any defect, which may arise due to the application of static electricity after the product has passed your company s acceptance inspection procedures. 4 We cannot accept responsibility for industrial property, which may arise through the use of your product, with exception to those issues relating directly to the structure or method of manufacturing of our product. SGD-origin longer than one year from SGD production.
A NOV.27, 08 25 / 25 11 Dimensional Outlines VERSION A DATE 2008.11.26 TOLERANCE MATERIAL FINISH MODEL NAME ±0.3 SCALE APPROVED NO. CHECKED UNIT mm DRAWN Ivan TITLE FILE NAME GATW80SP8K1R0 OUTLINE