REBAR SPLICING SYSTEM systèmes constructifs
FROM BAR TO SITE ONE PROCESS - ONE PRODUCTION WAY - ONE INSTALLATION Certify : A CONNECTION ALWAYS STRONGER THAN THE REBAR Bar break with visible necking during tensile tests Conception Thread coss section > rebar cross section, Thread length > standards for nuts and bolts, Cold upsetting + ISO profile thread with big pitch Final control of dimensions is indépendent from machinery : guaranty of conformity A CONNECTION TOLERANT TO MISTAKES The full efforts are transfered even with defects of the rebar geometry and / or the installation Advantages and tolerated mistakes Complete transfer of the effort even with a 20% unscrewed connection Profile difference, height of the ribs (depending on the rebar trade marks) : no influence on the result Possible loss of material on the thread : no influence on the strength Easy screwing, no danger of pollution of the thread Mechanical tools for control : normalised and calibrated, no way to have measurement trouble Optimization of the external dimensions of the coupler Impossible to connect a continuation bar of a different diameter Impossible to screw the continuation bar on the bias Self centering of the continuation bar inside the coupler Proper fitting is checked by a simple visual inspection No Torque Wrench needed Simple use even in projects with reinforcement congestion Security of the installation, Blind installation of the continuation bar in projects with reinforcement congestion Anyone can at any time check the connections with just one glance and with no tool No special tool, no calibrated tool No risk to damage the cnnection with a too high torque No risk that the torque is achieved but the efforts are not fully transfered A FINANCIALLY EFFICIENT CONNECTION through an industrial process, a manufacturing in large series, a proximity of construction sites, simple solutions for complex cases. Time saving Standardization Time saving Competitive prices even for complex connections Production ratio Industrial manufacturing of the couplers Easy installation on site
process COLD UPSETTING followed by an ISO profile threading STATIC RANGE DYNAMIC RANGE WE PROVIDE A CONNECTION AT LEAST 10% STRONGER THAN THE REBAR Tensile Test Elongation Measure Bar break THE COMPLIANCE WITH CURRENT STANDARDS AND RECOMMENDATIONS for following applications : Range C DYN Static X X Med. Earthquake X X Violent Earthquake X X Shocks X X Explosion X X Low Temperature X X Fatigue X Spannung in MPa (a) 600 400 200 0-200 2-0.5 f yk DD1-Lo 50 in % (b) Spannung in MPa 0,0 0,5 1,0 1,5 0,0 0,2 0,4 0,6 0,8 Dehnung in mm Fig. 1.4 - Essai de type "séisme violent" sur ø20mm : (a) diagramme effort - déformation du pilotage de l'essai : (b) allongement dans la zone du coupleur. 600 400 200 0-200 DEUTSCHES INSTITUT FÜR BAUTECHNIK Zulassungsnummer: Antragsteller: Anstalt des Öffentlichen Rechts Allgemeine bauaufsichtliche Zulassung Zulassungsgegenstand: Geltungsdauer bis: Der oben genannte Zulassung Diese allgemeine bauauf 28 rue de Liège 75008 PARIS Certificat DISPOSITIFS de RABOUTAGE ou d ANCRAGE d ARMATURES du BETON n M99/002 Rév. 13 attribué à BARTEC SYSTEMES CONSTRUCTIFS pour les Dispositifs de raboutage ou d'ancrage des armatures du béton Ce certificat comporte 4 pages - Le lecteur est invité à vérifier les conditions de validité de ce certificat (cf. fiche descriptive) Date de décision : 27/03/2012 Date de validité : 30/06/2015 LYON (69) COUPLEURS BARTEC Pour l AFCAB, B. CRETON, Président de l AFCAB Aucune mention ne peut être ajoutée ou retirée de ce certificat. Tout contrevenant s expose à des poursuites pour usage abusif de la marque.
production Rebar end treatment and Couplers CUTTING : The rebar end is cut with an automatic bandsaw. THREADING : The upset part is then threaded, by cutting for the range C, and by rolling for the range Dyn. All threads are in ISO-profile. Those operations are done with a specific BARTEC Technology machinery.rond à béton des modes COLD UPSETTING : For each diameter, a machinery and specific dies are used to define and control the volume of material to move and ensure the result. Contrôle : A final check on the thread is proceeded with a predefined frequency : With a calibrated ring for the profile and diameter, and with a depth gauge for the length. At this stage the product manufactured in certified workshops is able to ensure the total transmission of effort. No other additional test or check is needed. Couplers The coupler is manufactured industrially under strict quality control. The raw material has mechanical properties that are defined and permanently checked to ensure compliance of the connection to the most severe applications (earthquakes, shocks,...), the traceability of the material and manufacturing is ensured by a code stamped on each coupler. Cold upsetting Threading Tools Manufacturing of couplers Packaging of couplers Production check Independent of the machine Drawing of a workshop production
INSTALLATION The rebar is automatically centered by a chamfr at the end of the coupler. Impossible to connect a continuation rebar of a different Ø from that of the first rebar. Tightened with a spanner with no need to check the torque. Proper fitting by a simple visual inspection. Bad : visible thread Good : invisible thread Visual Inspection Four Types of connections using the same coupler. LS LSR Coupler unscrewing : the rebar does not move. Where the continuation bar can be easily rotated LCE Coupler unscrewing, the rebar does not move. Lock nut Release thread Standard thread Release thread Where rotating the continuation bar is difficult (due to weight, access, etc...) D LRD d Lock nut Where the continuation bar doesn t move Connection of two rebars of different diameters Miscellaneous solutions and accessories DDM RSB Standard sets Anchors LER Connection S couplers for welding V couplers for metal plates and 8.8 class bolt COL plastic flange COL metal flange RFI Insert for threading reservation
COUPLERS DIMENSIONS STATIC RANGE DYNAMIC RANGE COUPLER THREAD Reference O.D. Length ISO Stress Reference Area C12 ø20 33 M14x2,00 116 C14 ø22 37 M16x2,00 157 C16 ø25 46 M20x2,50 245 C18 ø30 50 M22x2,00 318 C20 ø30 55 M24x3,00 353 C22 ø36 57 M25x2,00 420 C24 ø36 61 M27x3,00 460 C26 ø38 68 M30x3,50 561 C26 ø38 68 M30x3,50 561 C28 ø45 74 M33x3,50 694 C32 ø47 81 M36x4,00 817 C32 ø47 81 M36x4,00 817 C34 ø50 87 M39x4,00 975 C36 ø54 91 M42x4,50 1121 C40 ø59 100 M45x4,50 1306 C50 80 124 M56x5,50 2030 C56 85 141 M64x6,00 2676 Dimensions in mm - Cross sections in mm 2 REBAR ø Stress nom. Area 12 113 14 154 16 201 18 254 20 314 22 380 24 452 25 491 26 531 28 616 30 707 32 804 34 908 36 1018 40 1257 50 1963 56 2463 THREAD COUPLER ISO Stress Reference O.D. Length Reference Area M16x1,75 162 DYN 14 ø25 37 M20x2,75 238 DYN 16 ø30 46 M24x2,75 360 DYN 20 ø37 55 M27x3,00 457 DYN 22 ø37 57 M30x3,00 580 DYN 26 ø42 68 M30x3,00 580 DYN 26 ø42 68 M36x3,00 865 DYN 32 ø52 81 M36x3,00 865 DYN 32 ø52 81 M39x3,50 1002 DYN 34 ø57 87 M45x4,00 1336 DYN 40 ø67 100 The raw material of couplers, the way the threads are formed and the tolerances are different from those in the static range. The sizing of the threaded sections avoids any danger of fixing the elements from one range onto the other. D16BARgb - 10/2012 systèmes constructifs BARTEC : Espace Européen - Bât. G 15 chemin du Saquin - F 69130 ECULLY Tél. : 33 (0) 4 72 34 95 15 - Fax : 33 (0) 4 72 34 95 35 www.bartec.eu - contact@bartec.eu