Keysight Basic Instruments

Keysight Keysight Basic Instruments Our Distributor Network RIGHT Instrument. RIGHT Expertise. Delivered RIGHT Now. May July 2015 New DMMs with lower current ranges make pa measurements easier than ever before SEE PAGE 2

SPOTLIGHT Measuring Dynamic Current Consumption with a Digital Multimeter One of the most challenging measurements is characterizing the power consumption of a battery powered device such as a portable radio transceiver. This application requires complete measurements of the current from sleep mode to full operating load. Dynamic current measurements with a digital multimeter (DMM) can be quite complex due to the range change based on the level of current being measured. There can be a very large difference between the two modes of operation. You can effectively monitor the power drain from your battery powered device using one DMM to monitor the voltage and another DMM to monitor the current. The typical current profile of a portable radio transceiver is complicated with a wide range of sleep, standby and active modes. As shown in Figure 1, the dynamic range of the current is large because the operating currents are drawing approximately 30 to 40 ma, while the standby currents are only 1 to 10 μa. In order to get accurate readings for both ranges with a DMM, you need to take multiple reading sweeps with different ranges. One method for capturing the current profile would be to run the Device-Under-Test (DUT) multiple times to capture the sleep and standby modes separately and then the operating mode currents. In the first capture, set the DMM to the 100-mA range and 0.001 PLC (20 μs per sample). This will capture the complete current signal, including the active mode values between 30 to 40 ma, but provides less resolution on the lower current measurements. Figure 2 shows a trend chart view of the currents read using a 3445A DMM. Notice that the lower current measurements seem to be very uniform, which is due to a loss of resolution. To measure the low current values, you need to take another measurement at a lower current range. Once you have captured the readings, the data can be saved to memory and analyzed on a PC. Next, you can set the DMM to a lower current range for the standby and/or sleep currents. Figure 3 shows a graphical data capture, using BenchVue software, of the standby currents measured by the top graph. The bottom graph shows the DCV readings. The currents captured vary from approximately 2 to 10 μa. They were captured with the DUT in standby mode, thus allowing for a single range current capture. Anything above 120 percent of the range will result in an overload condition. You can also use BenchVue software to control and trigger both DMMs simultaneously. Use the digitizing mode of the DMM to ensure 20 μs per sample. Summary While a N78x precision SMU (page 7) is designed to capture the current in a single pass, the 3445A and 34470A Truevolt DMMs can provide a lower cost solution when used for multiple pass measurements. BenchVue software is especially useful for viewing and analyzing the measurements recorded in this type of application. For more information visit www.keysight.com/find/truevolt www.keysight.com/find/benchvue Figure 2. This operating current was captured with the 3445A DMM. Shown here is the DMM front panel. Figure 1. Dynamic current profile from a portable radio Figure 3. These two graphs illustrate the digitized DCI (top image) and DCV (bottom image) consumption. Keysight Our Distributor Network RIGHT Instrument. RIGHT Expertise. Delivered RIGHT Now. Keysight and our network of Keysight Authorized Distributors have teamed up to provide fast, easy access to the world s largest selection of off-the-shelf T M instruments. It s the best of both worlds: Keysight s measurement expertise and product breadth combined with speed, convenience and same-day shipping from our distribution partners. It s never been easier to get the right instrument in the right hands, right away. 002 02 Basic Instruments / May August October July 2015 2014

Benchtop Digital Multimeters Exceptional performance and ease of use Features DCV, DCI Digits of True RMS resolution ACV/ACI Description U3401A Dual display. Elegantly simple and affordable DMMs with basic capabilities. U3402A 4½ 5½ U30B DMM with built-in 30 W power supply. Halves bench/rack space needed for two instruments. 5½ 34450A Faster measurement speed, ultra-bright OLED with dual display, and basic statistical tools. 5½ New industry standard. Display DMM results in ways you never have before and measure with unquestioned Truevolt confidence. ½ 3440A 3441A 34401A 34410A 34411A 3445A 34470A Industry standard for accuracy, speed, measurement ease and versatility. New 3441A is a 100% drop-in replacement for the 34401A. Dual display. Highest throughput of benchtop DMMs, best choice for system use. More measurements, higher speed, better accuracy, more memory than 3441A. 2 and 4 Freq/ Diode/ wire Ω period cont 2 wire Ω only ½ ½ Built-in PC interfaces N/A None 2 GPIB 190 1,000 1,000 10,000 serial (RS-232), optional GPIB optional LAN, GPIB LAN, optional GPIB serial (RS-232), GPIB GPIB, LAN 7½ 50,000 LAN, optional GPIB 250 serial (RS-232), GPIB 100,000 GPIB 20,000 GPIB, LAN 20,000 GPIB, LAN ½ Nano volt/µω meter. Very accurate, low-level measurements. 7½ DCV only 3458A The fastest, most flexible and most accurate multimeter, ideal multimeter for demanding applications. 8½ The world's only graphical picoammeter. B2983A* 0.01 fa minimum measurement resolution. ½ (0.01 fa) DCI only 2-wire only The world's only graphical electrometer. Measure down to 0.01 fa and up to B2987A* 10 PΩ (10 x1015 Ω) ½ (0.01 fa) DCI, DCV 2-wire only B2985A 300 34420A B2981A Cap. Max reading rate at 4½ digits (rdgs/s) Temp. 50,000 *Battery operated NEW 3445A, 34470A ½ and 7½ digit Truevolt digital multimeters New lower DC current ranges provide enhanced measurements on very low power devices. 1 µa range with pa resolution Measure sleep and standby current Capture dynamic current on active loads Find a Keysight distributor today at Indicates BenchVue-enabled products www.keysight.com/find/distributor Basic Instruments May July 2015 03

Handheld Instruments Optimized to make precise and dependable measurements in the demanding conditions you face on the job Keysight s family of handheld and portable test tools is constantly growing. From digital multimeters (DMMs) and basic capacitance meters, to oscilloscopes and clamp meters, our handheld and portable test tools will address the test and measurement capabilities you need to complete your tasks on the bench or in the field. www.keysight.com/find/hh U1253B U1230A Series U1240A Series U1250A Series U1270A Series Counts AC bandwidth Voltage AC/DC 000 1 khz 00 mv to 00 V 10,000 2 khz 1 V to 1000 V 50,000 Up to 100 khz 30,000 Up to 100 khz 50 mv to 1000 V 30 mv to 1000 Current AC/DC 0 μa to 10 A 1 ma to 10 A 500 μa to 10 A 300 μa to 10 A Battery life Additional features 500 hours Built-in LED flashlight, continuity alert with flashing backlight, Z Low, on-contact voltage detector with V sense 300 hours Switch counter, harmonic ratio, dual and differential temperature measurements Up to 72 hours Up to 300 hours Accessories U1117A IR-to-Bluetooth adapter: view measurements on your ios or Android smart device wirelessly and remotely U1115A Remote logging display: connect up to 4 handheld meters to read devices 100 meters away 20 MHz frequency counter, programmable square wave generator, organic LED display AC and/or DC voltage check, low impedance mode, offset compensation, organic LED display U5855A TrueIR thermal imager Get the clarity of 320 x 240 pixels at the cost of a 10 x 120 pixels detector with fine resolution capability Sensitivity (noise equivalent temperature difference): 0.07 ºC U1450A/U140A Series insulation resistance testers Measure insulation resistance up to 20 GΩ, earth bond resistance, AC and DC volts Certified to IP 7 rating, drop proof up to 3 m (10 ft), CAT III 1000 V and CAT IV 00 V Waveform Generators General-purpose and precision models with exclusive Trueform technology Trueform technology generates signals with the lowest jitter and distortion Generate Trueform arbitrary waveforms with less jitter, more fidelity and greater resolution Description Channels Frequency range Pulse Std/Opt arb # bits Arbitrary waveforms Sample rate Standard memory/ch Modulation Optional memory/ch AM/FM FSK PWM 33210A 33220A General-purpose function and arbitrary waveform generators. 1 20 MHz 5 MHz Std 14 50 MSa/s 4 K 10 MHz 5 MHz Opt 14 50 MSa/s 8 K 33250A 80 MHz 50 MHz Std 12 200 MSa/s 4 K 33509B/ 1 20 MHz 20 MHz Opt 1 10 MSa/s 1 M 1 M 33510B 2 33511B/ 33512B 33519B/ 35520B 33521B/ 33522B Exclusive Trueform waveform technology with <40 ps jitter and <0.04% THD. 1 2 1 2 1 2 20 MHz 20 MHz Std 1 10 MSa/s 1 M 1 M 30 MHz 30 MHz Opt 1 250 MSa/s 1 M 1 M 30 MHz 30 MHz Std 1 250 MSa/s 1 M 1 M 3311A 1 80 MHz 80 MHz Std 14 0 MSa/s 4 M 4 M Exclusive Trueform waveform 3312A technology at higher frequency 2 80 MHz 80 MHz Std 14 0 MSa/s 4 M 4 M 3321A ranges with <1 ps jitter <0.03% 1 120 MHz 100 MHz Std 14 1 GSa/s 4 M 4 M THD. 3322A 2 120 MHz 100 MHz Std 14 1 GSa/s 4 M 4 M 04 Basic Instruments May July 2015

Oscilloscopes, Adapters, and Software Big scope performance with a small scope price 1000 Series oscilloscopes 50 to 200 MHz, 2- and 4-channel DSO models with up to 20 kpts memory 5.7-inch color display offers powerful signal capture and display Up to 2 GSa/s sample rate Accelerate your productivity with 23 automatic measurements, an 11-language user interface, USB connectivity, and a standard educator s kit Oscilloscopes Breakthrough scope technology lets you see more, do more and get more for your money InfiniiVision oscilloscopes Up to 1,000,000 waveforms/sec update rate MegaZoom IV responsive, uncompromised smart memory 5 or in one instrument integration Fully upgradable bandwidth, MSO, serial analysis, built-in WaveGen function generator, or digital voltmeter and counter Accurately measure small noise on top of large DC N7020A power rail probe For a complete list of available probes: www.keysight.com/find/probes BenchVue software Look for this icon throughout the catalog to identify compatible products. 2 GHz single-ended active probe designed for power rail noise measurement Extremely low noise the probe increases the baseline noise of the scope by ~10% +/-24 V of large offset range enables users to center the signal on screen and utilize the max vertical sensitivity of a scope 50 kω DC impedance ensures low probe loading Compatible with Infiniium S/9000 Series and InfiniiVision 3000X/T, 4000 X-Series Visualize multiple measurements simultaneously Easily capture data, screen shots & system state Recall past state of your bench to replicate results Measurement data export to Excel, Word and MATLAB with three clicks Monitor and control your bench from mobile devices Measurement Hint Ripple, noise and transients riding on DC supplies are a major source of clock and data jitter in digital systems. Use a highbandwidth tool to evaluate and understand high-speed noise and transients on DC power rails. The N7020A power rail probe is a low noise, large offset range oscilloscope probe that enables users to measure these small signals. www.keysight.com/find/n7020a Keysight software is downloadable expertise Learn more at www.keysight.com/find/software 2000 X-Series 70 to 200 MHz bandwidth, up to 1 Mpts memory, DSO and MSO models 8.5-inch WVGA display Standard 5-year warranty, 2-year calibration cycle 3000T X-Series NEW 4000 X-Series 200 MHz to 1.5 GHz bandwidth, 4 Mpts memory (standard segmented memory), DSO and MSO models 12.1-inch capacitive touch display Zone touch triggering Standard 3-year warranty, 2-year calibration cycle Gain greater insight with powerful applications See the complete list at www.keysight.com/find/scope-apps Description 2000 X-Series 3000T X-Series 4000 X-Series 20 MHz WaveGen DSOX2WAVEGEN DSOX3WAVEGEN DSOX4WAVEGEN2 3-digit voltmeter and 5-digit counter DSOXDVM DSOXDVM 3-digit voltmeter and 8-digit counter DSOXT3DVMCTR DSO to MSO upgrade DSOX2MSO DSOX3MSO DSOXPERFMSO CAN/LIN trigger/decode DSOX2AUTO CAN/CAN-FD/CAN-dbc/LIN trigger/decode DSOXT3AUTO DSOX4AUTO SENT trigger/decode DSOXT3SENSOR DSOX4SENSOR I 2 C/SPI trigger/decode DSOX2EMBD DSOX3EMBD DSOX4EMBD RS232/UART trigger/decode DSOX2COMP DSOX3COMP DSOX4COMP USB full/low trigger/decode USB high trigger/decode USB signal quality test 100 MHz to 1 GHz bandwidth, 4 Mpts memory (standard segmented memory), DSO and MSO models 8.5-inch capacitive touch display Zone touch triggering Wide range of serial decodes and analysis Gated FFTs allow time-correlated views of the frequency domain Standard 3-year warranty and calibration cycle DSOX4USBFL DSOX4USBH DSOX4USBSQ Software application bundle DSOX2APPBNDL DSOXT3APPBNDL DSOX4APPBNDL Find a Keysight distributor today at www.keysight.com/find/distributor Basic Instruments May July 2015 05

Data Acquisition Units and Modules Modular flexibility and universal channels for a wide range of measurements with no external signal conditioning 34980A multifunction switch/ measure unit 34980A modules 34921A 34925A multiplexer switch modules 34937A 34939A GP switch modules 34931A 34934A matrix switch modules 34941A 34947A RF and µwave switch modules 34950A 34952A system control modules 34959A breadboard module 34970A/72A data acquisition switch units 34970A/72A modules 34901A/02A/08A multiplexers 34903A GP switch 34904A matrix 34905A/0A RF switches 34907A multi-function High performance, 8-slot mainframe with ½ digit DMM and built-in signal conditioning Choose from 21 plug-in modules, up to 1024 1-wire (50 2-wire) channels or 409 cross pts. Key specifications Up to 300 V, 40, 70 or 80 channels Up to 4 channels, and up to 300 V 4x8, 4x1, up to Quad 4x32 matrix Up to 2.5 GHz DIO, DAC, totalizer For custom designs with +12 V and + 5 V supplies Low-cost, 3-slot unit with ½ digit DMM and built-in signal conditioning Choose from 8 plug-in modules, up to 120 1-wire (0 2-wire) channels or 9 cross points 34972A has built-in Web interface Key specifications Up to 300 V, 1, 20, or 40 channels 300 V, 20 actuator channels 4x8 matrix 2 GHz dual, 50 and 75 Ω DIO, DAC, totalizer Measurement Hint Writing custom software to connect, record and convert data into results across multiple instruments can be tedious and time-consuming. Keysight s BenchVue software and DAQ app for the PC achieves results faster by easily viewing, logging and exporting measurement data and screen shots with a few clicks. www.keysight.com/find/benchvue Signal Analyzers, Signal Generators, Counters, and LCR Meter Achieve more on a tight budget: Solid performance with robust measurement features N9320B basic spectrum analyzer (BSA) N9322C basic spectrum analyzer (BSA) More resolution and speed with graphical display offers more insights 53200 Series RF and universal frequency counters 53210A 53220A 53230A Key specifications E4980AL precision LCR meter Frequency range: 9 khz to 3 GHz DANL: -148 dbm with pre-amp on 3 GHz tracking generator PowerSuite: channel power, occupied bandwidth, and more AM/FM and ASK/FSK demodulation analysis Free remote control PC software Frequency range: 9 khz to 7 GHz DANL: -152 dbm typical, with preamp on 7 GHz tracking generator, built-in VSWR bridge AM/FM, ASK/FSK demodulation Free remote control PC software 5-in-1 RF analyzer: Spectrum analyzer, stimulus and response tester, spur and interference analyzer, ASK/FSK modulation analyzer, peak and average power meter Professional performance and compact size for general-purpose testing needs N9310A RF signal generator 9 khz to 3 GHz CW output, 20 Hz to 80 khz low frequency (LF) output -127 to +13 dbm output level range (max +20 dbm settable) - 95 dbc/hz SSB phase noise Extensive analog modulation: AM, FM, phase, and pulse modulation Optional IQ modulator, 40 MHz bandwidth Frequency, frequency ratio, time interval, rise/fall time, phase, and much more Histograms, trend charts, data logging, and built-in math and statistical functions 53230A offers: 20 ps single-shot, burst microwave, and continuous gap-free measurements Optional or 15 GHz RF channel 350 MHz RF frequency counter, 10 digits/s 350 MHz universal frequency counter/timer, 12 digits/s, 100 ps 350 MHz universal frequency counter/timer, 12 digits/s, 20 ps Speed, accuracy, and measurement versatility 20 Hz to 300 khz / 500 khz / 1 MHz Exceptionally low noise at both low and high impedance to improve test quality; 0.05% basic impedance accuracy High speed at an affordable price: 12 ms (SHORT), 118 ms (MED), 343 ms (LONG) @ 1 MHz 201-point programmable list sweep 0 Basic Instruments May July 2015

DC Power Supplies, DC Power Analyzers, and Precision Sources HIGH VALUE BASIC DC POWER: Solid performance and robust features help you achieve more on lower budgets AC Source/Analyzers, DC Power Supplies, and DC Load STABLE, RELIABLE AC POWER: Make sure your designs can handle unpredictable real-world power E300 Series DC power supplies Output noise as low as 1mVp-p/0.2mVrms Fast load transient response time (<50 μs) 30 to 200 W outputs AC800 Series basic AC sources Four models, 500 to 4000 VA (dual range 135 / 270 Vrms, up to 120 A) Intuitive user interface Access and control the source remotely using a standard Web browser N5700 and N8700 Series system DC power supplies N8900 Series autoranging high-power system supplies 45 affordable models in compact 1U (750 and 1500 W) and 2U (3.3 and 5 kw) packages Up to 00 V or up to 400 A Programmability and built-in V I measure ments simplify test set ups 5 kw and 10 kw basic, single-output, autoranging programmable DC power for ATE applications 18 models that offer up to 1000 V or 340 A Easily parallel units to create one power supply with up to 100 kw of power HIGH PERFORMANCE DC POWER: Anticipate new demands with high speed, versatility, and accuracy 800B Series performance AC sources/analyzers Complete AC power test solution 3 models, up to 1750 VA (300 Vrms, up to 80 A) Extensive power measurement capabilities (i.e., DC capability) Built-in arbitrary waveform generator to simulate many types of power waveforms Versatile power solutions for demanding applications 00 Series high-performance DC supplies Fast, low-noise outputs improve measurement accuracy and test throughout 40 to 00 W, single output, up to 120 V, and up to 875 A Programmability and built-in V I measurements simplify test setups N700 modular power system family N700: Ideal DC power supply solution for automated test systems Small 1U mainframe (400, 00, 1200 W); up to 4 modules per mainframe More than 30 programmable DC power modules: basic to precision, and SMU; available in 20 to 500 W B290A Series low noise power sources 10 μvrms ultra-low noise precision current/voltage source Unmatched current and voltage sourcing resolution (.5-digit, 100 nv/10 fa) Innovative and precision ARB capability; built-in waveforms with speeds up to 10 khz NEW B2900A Series precision source/ measure units Indicates BenchVue-enabled products N705B: Deep insight into DUT power consumption without assembling a complex test system Integrated benchtop unit holds up to 4 N700 Series modules (00 W total) DMM, scope, arb, and data logger features New source/measure units and applicationspecific modules N78xA: Precision source/measure units to accurately emulate a battery to deliver exceptional battery life Outputs now up to 80 W, 20 V, ± 8 A Characterize a device's off-, sleep-, and transmit-mode current in one pass (na to A) Perform accurate battery rundown tests with the unique zero-burden current shunt Display I-V curves and other types of graphs on the front panel Best-in-class.5-digit sourcing and measurement resolution Wide application coverage from 100 nv / 10 fa to 210 V / 3 A DC and 10.5 A pulsed Fast operation and accurate programming for high-volume DC power supply test systems N3300 DC electronic load mainframe Stable and accurate Automated command list execution reduces workload on system controller 1800 W mainframe accepts up to six 150 to 00 W modules for simultaneous testing Maximum inputs up to 240 V and 120 A Measurement Hint Conventional digitizing data acquisition equipment with fixed ranging does not have enough dynamic range to capture dynamic current draw of battery-powered devices. However, by using the Keysight N780 Series SMU's seamless measurement ranging, you can accurately measure both the peak pulse and baseline sleep currents in a single pass over a long period of time. www.keysight.com/find/n780smu Find a Keysight distributor today at www.keysight.com/find/distributor Basic Instruments May July 2015 07

P.O. Box 402, Englewood, CO 80155-402 www.keysight.com/find/contactus Measuring standby currents with pico-amp resolution for battery-powered devices is now available. See page 2 NEW ½ and 7½ digit Truevolt Digital Multimeters (3445A, 34470A) Promotions Save 90% on oscilloscope applications Enable all the software applications on the 4000 X-Series oscilloscopes for one low price with the DSOX4APPBNDL application bundle and save more than 90% off the cost of buying each application individually. No promo code required Valid through September 30, 2015 worldwide. See our complete list of current promotions. www.keysight.com/find/promotions Get Greater Reliability Standard You ve come to expect the highest quality from Keysight. We stand behind our products with a three-year warranty that s standard on all instruments, worldwide. www.keysight.com/find/threeyearwarranty Bluetooth and the Bluetooth logos are trademarks owned by Bluetooth SIG, Inc., U.S.A. and licensed to Keysight Technologies, Inc. Technical data and pricing subject to change without notice. Keysight Technologies 2015 Published in USA, May 1, 2015 5992-0112ENDI www.keysight.com