ree XLamp MT-G EasyWhite LEDs PRODUT FAMILY DATA SHEET/ BINNING AND LABELING DOUMENT LD-DS36 REV 0 WWW.REE.OM/XLAMP PRODUT DESRIPTION The XLamp MT-G EasyWhite LED maximizes lumen density, eliminates chromaticity binning, and enables luminaire and bulb manufacturers to deliver consistent color and high efficacy light output in a new, compact, multi-die package. XLamp MT-G EasyWhite LEDs can reduce LED-to-LED color variation to within a 2-step MacAdam ellipse, 94% smaller than the total area of the corresponding ANSI 78.377 color region. The XLamp MT-G EasyWhite LED is the perfect choice for lighting applications where high luminous flux output is required from a single, small point source. Example applications include: LED retrofit bulbs, commercial/retail display spotlights, and other indoor general illumination applications. FEATURES TABLE OF ONTENTS ree EasyWhite color Label Product with haracteristics... ree Bin ode, 2 Qty, temperatures Flux Lot haracteristics... #... 2 10 Wide Range of operating Label Relative with ustomer Spectral Power Order ode,... 10 Distribution... 3 current - up to 4 A Qty, Reel ID, PO#... Electrical haracteristics... 4 10 85 binning and Relative Luminous Flux vs Soldercharacterization Point Temperature... 4 Low effective thermal resistance 1.5 /W Relative Luminous Flux vs urrent... 5 High lumen density Typical Spatial Distribution... 5 Performance Groups Wide viewing angle: 120 Brightness... 6 Minimum 80 RI at 2700 K and 3000 K T Performance Groups hromaticity... 6 Electrically neutral thermal path ree EasyWhite olor Temperatures... 7 Bin And Order ode Format... 8 Standard Order odes and Bins... 8 APPLIATIONS Notes... 9 Reflow Soldering haracteristics... 9 MR, PAR and other directional retrofit bulbs Mechanical Dimensions...11 Tape and Reel...12 ommercial/residential directional lighting Packaging...13 General indoor/outdoor illumination opyright 2011 ree, Inc. All rights reserved. The information in this document is subject to change without notice. ree, ree, Inc. opyright 2010 ree, Inc. All rights reserved. The information in this document is subject to change without notice. the ree logo and XLamp are registered trademarks and EasyWhite is a trademark of ree, Inc. 4600 Silicon Drive ree, the ree logo and XLamp are registered trademarks of ree, Inc. Durham, N 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp
PRODUT HARATERISTIS haracteristics Unit Minimum Typical Maximum Viewing Angle (FWHM) degrees 120 ESD lassification (HBM per Mil-Std-883D) lass 2 Effective Thermal Resistance, Junction to Solder-point /W 1.5 LED Junction Temperatures 150 D Forward urrent ma 4000 Forward Voltage (at 1100 ma, 85 ) V 5.6 Temperature oefficient of Voltage mv/ -4.5 Reverse Voltage V -5 Moisture Sensitivity Level Rating (MSL) MSL 1 FLUX HARATERISTIS @ 1100 MA (Tj =85 ) The following table provides several base order codes for XLamp MT-G EasyWhite LEDs. For additional order codes, as well as a complete description of the order-code nomenclature, please reference pages 6 through 8 of this document. olor T Range Base Order odes Min Luminous Flux (lm) (Tj =85 ) Order ode Group Flux (lm) F0 480 MTGEZW-00-0000-0B00F040F 4,000 K G0 520 MTGEZW-00-0000-0B00G040F H0 560 MTGEZW-00-0000-0B00H040F E0 440 MTGEZW-00-0000-0B00E035F 3,500 K F0 480 MTGEZW-00-0000-0B00F035F EasyWhite 4-Step 3,000 K G0 520 MTGEZW-00-0000-0B00G035F E0 440 MTGEZW-00-0000-0B00E030F F0 480 MTGEZW-00-0000-0B00F030F G0 520 MTGEZW-00-0000-0B00G030F Notes: ree maintains a tolerance of ±7% on flux and power measurements Minimum RI for EasyWhite color temperatures D0 400 MTGEZW-00-0000-0B00D027F 27F, 27H, 30F, 30H is 80 2,700 K E0 440 MTGEZW-00-0000-0B00E027F Minimum RI for EasyWhite color temperatures F0 480 MTGEZW-00-0000-0B00F027F 35F, 35H, 40F, 40H is 77 Typical RI for EasyWhite color temperatures 35F, 35H, 40F, 40H is 80 ree maintains a tolerance of ±2 on RI measurements 2
olor T Range Base Order odes Min Luminous Flux (lm) (Tj =85 ) Order ode Group Flux (lm) F0 480 MTGEZW-00-0000-0B00F040H 4,000 K G0 520 MTGEZW-00-0000-0B00G040H H0 560 MTGEZW-00-0000-0B00H040H E0 440 MTGEZW-00-0000-0B00E035H 3,500 K F0 480 MTGEZW-00-0000-0B00F035H EasyWhite 2-Step G0 520 MTGEZW-00-0000-0B00G035H E0 440 MTGEZW-00-0000-0B00E030H 3,000 K F0 480 MTGEZW-00-0000-0B00F030H G0 520 MTGEZW-00-0000-0B00G030H D0 400 MTGEZW-00-0000-0B00D027H 2,700 K E0 440 MTGEZW-00-0000-0B00E027H F0 480 MTGEZW-00-0000-0B00F027H Relative Spectral Power Distribution White RELATIVE The following SPETRAL graph represents POWER typical spectral DISTRIBUTION output of each die of (Ithe F = MT-G 1100 MA, T J = 85, 3000K T) This is XR-E data, and M-E Data The following graph represents typical spectral output of the XLamp MT-G EasyWhite LED. 100 Relative Spectral Power (%) 80 60 40 20 0 400 450 500 550 600 650 700 750 Wavelength (nm) 3
ELETRIAL HARATERISTIS (T J = 85 ) Electrical haracteristics (Tsp = 85º) The following graph represents typical electrical characteristics of the XLamp MT-G EasyWhite LED. 4000 3500 3000 urrent (ma) 2500 2000 1500 1000 500 0 5 5.5 6 Forward Voltage V Relative RELATIVE Flux LUMINOUS Output FLUX vs. VS JUNTION Junction TEMPERATURE Temperature (I F = 1100 (If = MA) 1100 ma) The following graph represents typical performance of each LED die in the XLamp MT-G The following graph represents typical performance of the XLamp MT-G EasyWhite LED. 120% Relative Luminous Flux 100% 80% 60% 40% 20% 0% 20 40 60 80 100 120 140 Junction Temperature (º) 4
Relative Intensity vs. urrent (Tsp = 85º) RELATIVE LUMINOUS FLUX VS URRENT (T J = 85 ) The following graph represents typical performance of the XLamp MT-G EasyWhite LED. 300% Relative Luminous Flux (%) 250% 200% 150% 100% 50% 0% 0 500 1000 1500 2000 2500 3000 3500 4000 Forward urrent, Pulsed (ma) TYPIAL SPATIAL DISTRIBUTION Spatial Distribution The following graph represents typical performance of the XLamp MT-G EasyWhite LED. 100 Relative Luminous Intensity (%) 80 60 40 20 0-90 -60-30 0 30 60 90 Angle (º) 5
PERFORMANE GROUPS BRIGHTNESS (I F = 1100 MA, T J = 85 ) XLamp MT-G EasyWhite LEDs are tested for luminosity and placed into one the following bins. Group ode Min. Luminous Flux @ 1100 ma, Tj=85 Max. Luminous Flux @ 1100 ma, Tj=85 D0 400 440 E0 440 480 F0 480 520 G0 520 560 H0 560 600 PERFORMANE GROUPS HROMATIITY (T J = 85 ) XLamp MT-G EasyWhite LEDs are tested for chromaticity and placed into one of the regions defined by the following bounding coordinates. EasyWhite olor Temperatures 4-Step ode T x y 0.3744 0.3685 0.3782 0.3837 40F 4000 K 0.3912 0.3917 0.3863 0.3758 0.3981 0.3800 0.4040 0.3966 35F 3500 K 0.4186 0.4037 0.4116 0.3865 0.4242 0.3919 0.4322 0.4096 30F 3000 K 0.4449 0.4141 0.4359 0.3960 0.4475 0.3994 0.4573 0.4178 27F 2700 K 0.4695 0.4207 0.4589 0.4021 EasyWhite olor Temperatures 2-Step ode T x y 0.3784 0.3741 0.3804 0.3818 40H 4000 K 0.3867 0.3857 0.3844 0.3778 0.4030 0.3857 0.4061 0.3941 35H 3500 K 0.4132 0.3976 0.4099 0.3890 0.4291 0.3973 0.4333 0.4062 30H 3000 K 0.4395 0.4084 0.4351 0.3994 0.4528 0.4046 0.4578 0.4138 27H 2700 K 0.4638 0.4152 0.4586 0.4060 6
REE EASYWHITE OLOR TEMPERATURES PLOTTED ON THE 1931 IE URVE (T J = 85 ) 0.45 0.44 ANSI 78.377 Quadrangle EasyWhite "F" (4-Step) hromaticity Regions 3000K 2700K 0.43 3500K 0.42 4000K 0.41 4500K y 0.40 0.39 35F 30F 27F 0.38 0.37 40F 0.36 0.35 0.36 0.37 0.38 0.39 0.40 0.41 0.42 x 0.43 0.44 0.45 0.46 0.47 0.48 0.49 0.45 0.44 ANSI 78.377 Quadrangle EasyWhite "H" (2-Step) hromaticity Regions 3000K 2700K 0.43 3500K 0.42 4000K 0.41 4500K 27H y 0.40 0.39 35H 30H 0.38 40H 0.37 0.36 0.35 0.36 0.37 0.38 0.39 0.40 0.41 0.42 x 0.43 0.44 0.45 0.46 0.47 0.48 0.49 7
BIN AND ORDER ODE FORMAT Bin codes and order codes are configured as follows: Order ode Series MTG = MT-G Internal code Internal code Kit code SSS-BB-HHHH-NNNNNNNNN Vf class: B = 6-V class Reel size 0 = 500 (standard) 1 = 100 (nonstandard) olor EZW = EasyWhite Bin ode SSS-BB-WWW-FF-GAAAAAA Series MTG = MT-G Internal code Flux bin Internal code Vf class: B = 6-V class hromaticity bin olor EZW = EasyWhite STANDARD ORDER ODES AND BINS (XLAMP MT-G EASYWHITE) XLamp MT-G EasyWhite LED Standard Order odes Min. Luminous Flux (lm) @ 1100 ma, Tj=85 Group Flux (lm) D0 400 E0 440 F0 480 G0 520 H0 560 hromaticity Regions 27F 27H 27F 27H 30F 30H 35F 35H 27F 27H 30F 30H 35F 35H 40F 40H 30F 30H 35F 35H 40F 40H 40F 40H EasyWhite Order ode MTGEZW-00-0000-0B00D027F MTGEZW-00-0000-0B00D027H MTGEZW-00-0000-0B00E027F MTGEZW-00-0000-0B00E027H MTGEZW-00-0000-0B00E030F MTGEZW-00-0000-0B00E030H MTGEZW-00-0000-0B00E035F MTGEZW-00-0000-0B00E035H MTGEZW-00-0000-0B00F027F MTGEZW-00-0000-0B00F027H MTGEZW-00-0000-0B00F030F MTGEZW-00-0000-0B00F030H MTGEZW-00-0000-0B00F035F MTGEZW-00-0000-0B00F035H MTGEZW-00-0000-0B00F040F MTGEZW-00-0000-0B00F040H MTGEZW-00-0000-0B00G030F MTGEZW-00-0000-0B00G030H MTGEZW-00-0000-0B00G035F MTGEZW-00-0000-0B00G035H MTGEZW-00-0000-0B00G040F MTGEZW-00-0000-0B00G040H MTGEZW-00-0000-0B00H040F MTGEZW-00-0000-0B00H040H 8
NOTES Moisture Sensitivity In testing, ree has found XLamp MT-G EasyWhite LEDs to have unlimited floor life in conditions 30º / 85% relative humidity (RH). Moisture testing included a 168 hour soak at 85º / 85% RH followed by 3 reflow cycles, with visual and electrical inspections at each stage. RoHS ompliance The levels of environmentally sensitive, persistent biologically toxic (PBT), persistent organic pollutants (POP), or otherwise restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2002/95/ E on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS), as amended through April 21, 2006. Vision Advisory laim WARNING. Do not look at exposed lamp in operation. Eye injury can result. For more information about LEDs and eye safety, please refer to the ree LED Eye Safety application note. REFLOW SOLDERING HARATERISTIS In testing, ree has found XLamp MT-G EasyWhite LEDs to be compatible with JEDE J-STD-020, using the parameters listed below. As a general guideline, ree recommends that users follow the recommended soldering profile provided by the manufacturer of solder paste used. Note that this general guideline may not apply to all PB designs and configurations of reflow soldering equipment. 9
Profile Feature Lead-Based Solder Lead-Free Solder Average Ramp-Up Rate (Ts max to Tp) 3 /second max. 3 /second max. Preheat: Temperature Min (Ts min ) 100 150 Preheat: Temperature Max (Ts max ) 150 200 Preheat: Time (ts min to ts max ) 60-120 seconds 60-180 seconds Time Maintained Above: Temperature (T L ) 183 217 Time Maintained Above: Time (t L ) 60-150 seconds 60-150 seconds Peak/lassification Temperature (Tp) 215 260 Time Within 5 of Actual Peak Temperature (tp) 10-30 seconds 20-40 seconds Ramp-Down Rate 6 /second max. 6 /second max Time 25 to Peak Temperature 6 minutes max. 8 minutes max. Note: All temperatures refer to the topside of the package, measured on the package body surface. 10
6 5 NOTIE EONFIDENTIAL. THIS PLOT AND THE INFORMATION INED PLOT WITHIN AND THE ARE INFORMATION THE PROPRIETARY AND ENTIAL E PROPRIETARY INFORMATION ANDOF REE, IN. THIS PLOT ON T BE OF OPIED, REE, IN. REPRODUED THIS PLOT OR DISLOSED TO ANY HORIZED ODUED PERSON OR DISLOSED WITHOUT TO THE ANY WRITTEN ONSENT WITHOUT E IN. THE WRITTEN ONSENT 5 4 4 3 3 2 1 2 REVISONS 1 REVISONS REV DESRIPTION BY DATE APP'D REV DESRIPTION BY DATE APP'D A INITIAL RELEASE D 10/8/10 A INITIAL RELEASE D 10/8/10 B HANGED SOLDER PAD VIEW D 1/11/11 BXLAMP HANGED MT-G SOLDER EASYWHITE PAD VIEW D LEDS 1/11/11 ADDED STENIL VIEW D 2/18/11 ADDED STENIL VIEW D 2/18/11 D HANGED OVERALL DIM TO MATH UT LENGTH AND WIDTH D 3/25/11 MEHANIAL DIMENSIONS 6 NOTIE REE ONFIDENTIAL. THIS PLOT AND THE INFORMATION ONTAINED WITHIN ARE THE PROPRIETARY AND ONFIDENTIAL INFORMATION OF REE, IN. THIS PLOT MAY NOT BE OPIED, REPRODUED OR DISLOSED TO ANY UNAUTHORIZED PERSON WITHOUT THE WRITTEN ONSENT OF REE IN. 5 4 3 2 D D REV DESRIPT A INITIAL REL All measurements are ±.13 mm unless otherwise indicated. B HANGED SOLDE ADDED STEN D 9.113 4.85 ±.25 4.85 ±.25.650.650 9.113 9.113 4.85 ±.25.650 R4.100 R4.100 0 6.000 0 6.000.500.500.889 1.090.889 1.090 9.113 8.839 8.839.889.889 1.090 1.090.500.500 6.000 6.000 B B.937.937 3.175 3.175 0 8.072 06.198 8.072 6.198 1.722 1.722 R4.100 0.500 1.072 B 6.000 D REOMMENDED P BOARD SOLDER P BOARD PADSOLDER PAD.500 1.072 1.905 1.905 1.905 1.905.937.937.889 1.090 REOMMENDED REOMMENDED STENIL STENIL PATTERN PATTERN 3.175 3.175.500 DRAWN BY DATE DATE DRAWN BY UNLESS UNLESS OTHERWISE OTHERWISE SPEIFIED SPEIFIED DIMENSIONS DIMENSIONS ARE IN ARE IN D. RONIN D. RONIN 10/8/10 10/8/10 HEK MILLIMETERS MILLIMETERS AND AFTER AND AFTER FINISH. FINISH. HEK DATE DATE TOLERANE TOLERANE UNLESS UNLESS SPEIFIED: SPEIFIED: 1.090 APPROVED APPROVED.XX ±.XX.25 ±.25 DATE DATE.XXX.XXX ±.125 ±.125 TITLE TITLE X ± X.5 ±.5 THIRD ANGLE THIRD PROJETION ANGLE PROJETION MATERIAL MATERIAL FOR SHEET FOR SHEET METAL METAL PARTS PARTS ONLY ONLY.X ±.X ± 1.5 1.5.937.XX ±.XX.75 ±.75 SIZE SIZE.XXX.XXX ±.25 ±.25 FINAL PROTETIVE FINAL PROTETIVE FINISH FINISH X ± X.5 ±.5 DRAWING NO. 2610-00011 4600 4600 Silicon Silicon Drive Drive Durham, Durham, N. N. 27703 27703 Phone Phone (919) (919) 313-5300 313-5300 Fax Fax (919) (919) 313-5558 313-5558 TIGER 9191 OUTLINE SALE SHEET OF SURFAE FINISH: 1.6 SHEET OF SURFAE FINISH: 1.6 9.000 1 /11 /1 6 5 5 4 4 3 3 2 2 1 1 8.839.889 3.175 6.000 REV. REV. D A A 0 8.072 6.198 1.722 3.175.937 A REOMMENDED P BOARD SOLDER PAD 1.072 1.905 1.905 REOMMENDED STENIL PATTERN THIRD ANGLE PROJETION UNLESS OTHERWISE SPEIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANE UNLESS SPEIFIED:.XX ±.25.XXX ±.125 X ±.5 DRAWN BY HEK APPROVED FOR SHEET METAL PARTS ONLY MATERIAL.X ± 1.5.XX ±.75.XXX ±.25 FINAL PROTETIVE FINISH X ±.5 SURFAE FINISH: 1.6 D. RONIN DATE 10/8/10 DATE DATE T SI S 6 5 4 3 2 11
6 5 4 3 2 1 NOTIE REE ONFIDENTIAL. THIS PLOT AND THE INFORMATION ONTAINED WITHIN ARE THE PROPRIETARY AND ONFIDENTIAL INFORMATION OF REE, IN. THIS PLOT MAY NOT BE OPIED, REPRODUED OR DISLOSED TO ANY UNAUTHORIZED PERSON WITHOUT THE WRITTEN ONSENT OF REE IN. REVISONS REV DESRIPTION BY DATE APP'D XLAMP MT-G EASYWHITE LEDS D TAPE AND REEL D END 1.5±.1 12±.1 User Feed Direction 4±.10 ATHODE SIDE START 1.75 ±.10 5.25 16 +.3 -.0 9.4 Trailer 160mm (min) of empty pockets sealed with tape (15 pockets min.) Loaded Pockets (500 Lamps) ANODE SIDE Leader 400mm (min) of empty pockets sealed with tape (35 pockets min.) B B A DRAWN BY DATE UNLESS OTHERWISE SPEIFIED DIMENSIONS ARE IN D. RONIN 1/28/11 MILLIMETERS AND AFTER FINISH. HEK DATE TOLERANE UNLESS SPEIFIED: -- --.XX ±.25 APPROVED DATE.XXX ±.125 TITLE X ±.5 -- -- THIRD ANGLE PROJETION MATERIAL FOR SHEET METAL PARTS ONLY.X ± 1.5 SIZE.XX ±.75 --.XXX ±.25 FINAL PROTETIVE FINISH X ±.5 SURFAE FINISH: 1.6 MTG LOADING SPE DRAWING NO. 2402-00016 REV. SALE SHEET OF 3.000 1 /1 6 5 4 3 2 1 -- 4600 Silicon Drive Durham, N. 27703 Phone (919) 313-5300 Fax (919) 313-5558 A A 12
PAKAGING Humidity Humidity Indicator Indicator ard (inside (inside bag) bag) Dessicant Desiccant (inside bag) bag) Vacuum-Sealed Moisture Vacuum-Sealed Barrier Bag Moisture Moisture Vacuum-Sealed Barrier Barrier Bag Bag Moisture Barrier Bag REE Label Bin with oderee Bin & ode, Barcode REE Label Qty, Bin Label with ode Lot ree # Bin & ode, Barcode Qty, Label Lot # Label with with ustomer ree Bin ode, P/N, Label Qty, Qty, Lot with with #, ustomer Lot PO ree ## Bin ode, P/N, Qty, Qty, Lot #, Lot PO # Patent Label Patent Label Label with ustomer Order ode, Label Qty, with Reel ustomer ID, PO # Order ode, Qty, Reel ID, PO # Label with ustomer Order ode, Qty, Reel ID, PO# Label with ree Bin ode, Qty, Lot # 13