Saber 1000 Series Enterprise SSD 2.5 Solid-State Drive SB1CSK31MT5XX-xxxx The OCZ 2.5 of Solid State Drives are designed specifically to address Enterprise storage and computing applications where demanding performance, reliability, and the total cost of ownership (TCO) are major factors. SSD Datasheet
SATA Solid State Drive Part Number Bulk Packaging Description UPC SB1CSK31MT560-0120.B, SATA III 2.5 MLC, 120GB 842024037514 SB1CSK31MT560-0240.B, SATA III 2.5 MLC, 240GB 842024037507 SB1CSK31MT570-0480.B, SATA III 2.5 MLC, 480GB 842024037491 SB1CSK31MT5D0-0960.B, SATA III 2.5 MLC, 960GB 842024037484 A Bulk Packaging order contains 10 drives in a box without individual packaging Part Number Single Packaging Description UPC SB1CSK31MT560-0120, SATA III 2.5 MLC, 120GB 842024037224 SB1CSK31MT560-0240, SATA III 2.5 MLC, 240GB 842024036876 SB1CSK31MT570-0480, SATA III 2.5 MLC, 480GB 842024036883 SB1CSK31MT5D0-0960, SATA III 2.5 MLC, 960GB 842024036890 2
Form Factor 2.5 7mm Form Factor SATA III / 6Gb/s Interface Capacity: 120GB, 240GB, 480GB and 960GB Components: A19nm MLC NAND Flash Memory Security: AES 256-bit Encryption Bandwidth Performance Specifications 1,3,4 Sustained Sequential Read: 550 MB/s Sustained Sequential Write: 475 MB/s Read and Write IOPS specifications (Full LBA Range, IOmeter*Queue Depth 32) 1,2,4 Sustained Random 4KB Reads: up to 91K IOPS Sustained Random 4KB Writes: up to 22K IOPS Compatibility SATA Revision 3.0, compatible with 3Gb/s and 6Gb/s interface rates ATA/ATAPI-8 Compliant SMART ATA feature set Native Command Queuing (NCQ) command set Data set management TRIM Command Power Management 5 V SATA Supply Rail Supports ATA Power Management Specification OS-Aware Hot Plug/Removal Power Specifications 5 Active: 4.1W (Typical) Idle: 0.6 W (Typical) Temperature Operating 6 : 0 C to 70 C Non-Operating: -45 C to 85 C Temperature monitoring Reliability Mean Time Between Failures (MTBF): 2 Million Hours Endurance Rating 0.4 DWPD Uncorrectable Bit Error Rate (UBER): 1 sector per 10 15 bits read Power Failure Management Plus (PFM+) partial PFAIL Shock (Operating and non-operating) 1000G/0.5 msec. Vibration Operating Range: 2.17 GRMS (7-800 Hz) Non-operating: 16.3 GRMS (20-2000 Hz) Altitude Operating Range: -1000 ft. to 10,000 ft. Non-operating: -1000 ft. to 40,000 ft. Product Ecological Compliance RoHS Certifications and Declarations: CE, FCC, KCC, BSMI, C-TICK, VCCI, RoHS, cul, WEEE Service and Support: 5 years 1. Performance values vary by capacity 2. Based on Random 4KB QD32 workload, measurement taken once the workload has reached steady state 3. Based on 128KB sequential transfer, measurement taken once the workload has reached steady state 4. Sustained performance measured using IOmeter* with Queue Depth 32. Measurements are performed using SNIA based metrics. 5. Using IOmeter ruining 1MB Sequential Writes QD32 the typical active power consumption is 4.1W with 1TB Saber drive, as measured by temperature sensor. 3
1. Introduction... 6 1.1 Product Overview... 6 2. Product Regulatory Certification and Compliance... 7 3. Product Specifications...... 8 3.1 Capacity... 8 3.2 Performance... 9 4. Reliability... 10 4.1 Endurance Rating... 10 4.2 Reliability Specifications... 10 5. Electrical Characteristics... 11 5.1 Supply Voltage... 11 5.2 Power Consumption: (5V Supply)... 11 6. Environmental Specifications... 12 6.1 Temperature, Shock, Vibration, Altitude... 12 6.2 Acoustics... 13 6.3 Emissions... 14 7. Additional Features... 14 7.1 Encryption... 14 7.2 Power Failure Management... 14 7.3 Temperature Monitor and Logging... 14 7.4 Device Activity Signal (DAS) indication... 14 7.5 Secure Erase... 14 7.6 Force Unit Access (FUA)... 14 7.7 Spread Spectrum Clocking (SSC)... 14 8. Pin and Signal Descriptions... 15 8.1 Pin Locations... 15 8.2 Hot Plug Support... 15 8.3 Signal Description Table... 15 9. ATA Support... 17 4
9.1 ATA Command Support... 17 9.2 IDENTIFY Device Data... 19 9.3 Power Management Support... 22 9.3.1 ATA Power Modes...... 22 9.3.2 SATA Link Power States... 22 10. S.M.A.R.T. Attribute Support... 22 11. Mechanical Specifications... 24 12. Glossary... 25 13. Revision History... 26 5
1. Introduction This document describes the specification and capabilities of OCZ Solid State Drives. The OCZ SSDs are optimized to deliver high read performance and reliability that is required for entry-level enterprise applications. 1.1 Product Overview The SSDs deliver excellent steady state performance, with highly developed flash management capabilities that extends NAND flash life and enhance drive reliability. Built with the OCZ Barefoot 3 controller combined with OCZ's optimized firmware architecture, Saber 1000 Series SSDs deliver data at a high-level of application performance. The drive also comes with built in Power Failure Management Plus (PFM+) protection that safeguards Saber 1000 against bricking during unexpected power loss. This 2.5 form factor SSD product has a Serial ATA-6Gb/s interface and it is designed using Toshiba A19nm MLC NAND flash memory available in 120GB, 240GB, 480GB, 960GB capacities. OCZ SSDs offers these key features: Comprehensive S.M.A.R.T. attributes Power Failure Management Plus (PFM+) to avoid brick drive syndrome UBER: 10 15 bits read Temperature Sensor for monitoring and logging Inrush current management AES 256-bit Encryption 0.4 DWPD Backed by a 5 year warranty 6
2. Product Regulatory Certification and Compliance Table 1. Certification/Compliance CE Compliant FCC Compliant B KC mark (Korea Certification) BSMI C-TICK VCCI RoHS Compliant UL WEEE Description Low Voltage Directive 2006/95/EC of the European Parliament and of the council of 12 December 2006, electromagnetic compatibility Directive 2004/108/EC of the European Parliament and of the Council of 15 December 2004 FCC Class B devices are those that are for use in a commercial. Industrial or business environment. Class B devices are those that are marketed for use in the home Compliance with paragraph 1 of Article 11 of the Electromagnetic Compatibility Control Regulation and meets the Electromagnetic Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Ministry of Information and Communication Republic of Korea. Bureau of Standards, Metrology, and Inspection (BSMI) is required for electrical, mechanical, and chemical products. Compliance with the Australia/New Zealand Standard AS/NZS3548 and Electromagnetic Compatibility (EMC) Framework requirements of the Australian Communication Authority (ACA). Voluntary Control Council for Interface to cope with disturbance problems caused by personal computers or facsimile. Restriction of Hazardous Substance Directive. UL 60950-1, 2nd Edition,2007-03-27 (Information Technology Equipment - Safety - Part 1: General Requirements) CSA C22.2 No. 60950-1-07, 2nd Edition, 2007-03 (Information Technology Equipment - Safety Part 1: General Requirements) The Waste Electrical and Electronic Equipment Directive (WEEE Directive) is the European Community directive 2002/96/EC on waste electrical and electronic equipment.
3. Product Specifications 3.1 Capacity Table 2. RAW Capacity Usable Capacity Total User Addressable Sectors in LBA Mode 128GB 120GB 234,441,648 256GB 240GB 468,862,128 512GB 480GB 937,703,088 1024GB 960GB 1,875,385,008 Notes: 1GB = 1billion bytes, actual formatted capacity less LBA count shown represents total user storage capacity and will remain the same throughout the life of the drive. The total usable capacity of the SSD may be less than the total physical capacity because a small portion of the capacity is used for NAND flash management and maintenance purposes. 8
3.2 Performance Table 3. Maximum Sequential Read and Write Bandwidth OCZ Saber 1000 Metric Units 120GB 240GB 480GB 960GB Max Read MB/s 550 550 550 550 Max Write MB/s 300 500 475 445 Notes: Maximum performance measured using SNIA IOmeter* 2010 Benchmarks, 1M block, Queue Depth 32 Table 4. Maximum Random Read/Write Input/Output per Second (IOPS) (FOB) OCZ Saber 1000 Metric Units 120GB 240GB 480GB 960GB 4KB Random Read 90,000 90,000 96,000 95,000 IOPS 4KB Random Write 81,000 80,000 87,000 83,000 Notes: Performance measured using SNIA IOmeter*, with Queue Depth 32, 1 minute. Measurements are performed on a full Logical Block Address (LBA) using 4KB Random Writes/Reads Table 5. Sustained Performance Metric Units OCZ Saber 1000 120GB 240GB 480GB 960GB 128K Sequential Read 1 MB/s 550 550 550 550 128K Sequential Write 1 MB/s 300 500 475 445 4K Random Read 1 IOPS 90,000 90,000 90,000 91,000 4K Random Write 1 IOPS 12,000 21,000 22,000 16,000 Notes: 1 Sustained performance measured using IOmeter* with Queue Depth 32. Measurements are performed using SNIA based metrics. 9
4. Reliability OCZ SSDs meets or exceeds SSD endurance and data retention requirements as specified in the JESD218 standard. Reliability specifications are listed in the tables below: 4.1 Endurance Rating The Endurance Rating of the SSD is represented in DWPD, Drive Writes Per Day, complete drive writes by a host to the SSD over 5 years. TBW, terabyte written by a host to the SSD over 5 years. Table 6. Description I/O Workload Condition 120GB 240GB 480GB 960GB DWPD over product lifetime 4K Random Write 0.4 0.4 0.4 0.4 TBW over product lifetime 4K Random Write 1 84 161 343 692 Notes: 1 TBW is the total amount of data written for entire product lifetime. 1 Terabyte = 1,000,000,000 Byte. 4.2 Reliability Specifications Table 7. Parameter Value Data Retention The time period for retaining data in the NAND at maximum rated endurance 1 year power-off retention once SSD reaches rated write endurance at 40 o C MTBF Mean Time Between Failures is estimated based on Telcordia* methodology and demonstrated through Reliability Demonstration Test (RDT). Error Correction Code (ECC) Error-Correcting Code defines the number of correctable symbols for a given size of data. 2,000,000 hours 40 bits correctable per 1K/data path parity protection 10
Uncorrectable Bit Error Rate (UBER) Uncorrectable bit error rate will not exceed one sector in the specified number of bits read. In the unlikely event of a non-recoverable read error, the SSD will report it as a read failure to the host; the sector in error is considered corrupt and is not returned to the host. 1 sector per 10 15 bits read with 1 year data retention at the end of life 5. Electrical Characteristics 5.1 Supply Voltage Table 8. Description Min Max Unit Operating Voltage for 5 V (+/- 5%) 4.75 5.25 V 5.2 Power Consumption: (5V Supply) Table 9. Mode Typical Unit Active 1 4.1 W Idle 2 0.6 W Notes: 1 Based on 5V supply using IOmeter 1MB Sequential Writes at QD32 with 960GB density. 2 Idle modes are measured off power supply using Bench Supply Software for maximum, average and minimum values. 11
6. Environmental Specifications 6.1 Temperature, Shock, Vibration, Altitude Table 10. Case Temperature Operating 1 Non-operating Temperature Range 0 70 C -45 85 C Shock, Vibration, Altitude Range Shock 2 Operating Non-operating Vibration 3 Operating Non-operating 1000G/0.5ms 1500G/0.5ms 2.17 GRMS (7-800 Hz) 16.3 GRMS (20-2000 Hz) Altitude 4 Operating Non-operating -1000 ft. to 10,000 ft. -1000 ft. to 40,000 ft. Notes: 1 As measured by temperature sensor 2 Shock specifications assume the SSD is mounted securely with the input vibration applied to the drivemounting screws. Stimulus may be applied in the X, Y or Z axis. Shock specification is measured using Root Mean Squared (RMS) value. 3 Vibration specifications assume the SSD is mounted securely with the input vibration applied to the drive-mounting screws. Stimulus may be applied in the X, Y or Z axis. Vibration specification is measured using RMS value. 4 Applies to atmospheric pressure only 12
6.2 Acoustics The drive has no moving or noise-emitting parts. Therefore, it produces no audible sound (0 db) in all modes of operation. 6.3 Emissions The OCZ SSDs are compliant to the FCC and CE Emission regulations. Table 11. Standards Description Results FCC 15.107 Conducted Emissions Compliant FCC 15.109 Radiated Emissions Compliant EN 55024 4.2.1 Electrostatic Discharge EN Compliant 61000-4-2 EN 55024 4.2.2 Electrical Fast Transients EN Compliant 61000-4-4 EN 55024 4.2.3.1 Continuous Radiated Compliant Disturbances EN 61000-4-3 EN 55024 4.2.3.2 Continuous Conducted Compliant Disturbances EN 61000-4-6 EN 55024 4.2.4 Power-frequency Magnetic N/A Fields EN 61000-4-8 EN 55024 4.2.5 Surges EN 61000-4-5 Compliant EN 55024 4.2.6 Voltage Dips and Interruptions Compliant EN 61000-4-11 EN 55022 5 Conducted Emissions Compliant EN 55022 6 Radiated Emissions Compliant EN 61000-3-2 Harmonic Current Emissions Compliant EN 61000-3-3 Voltage Fluctuations and Flicker Compliant 13
7. Additional Features 7.1 Encryption The OCZ SSDs features AES-256-bit encryption with automatic hardware encryption to provide protection of all metadata and user s data at all times. 7.2 Power Failure Management The OCZ SSD supports Power Failure Management Plus (PFM+), or partial PFAIL, which prevents brick drive syndrome so the SSD remains operational post outage. In flight data is not protected for unexpected system power loss. 7.3 Temperature Monitor and Logging The SSDs has an internal temperature sensor for monitoring temperature. The feature can be monitored using SMART attributes. 7.4 Device Activity Signal (DAS) indication The SSD DAS LED polarity is set automatically to the default state during manufacturing. The polarity can be inverted in the field using Clout or SSD ProTools. 7.5 Secure Erase OCZ recommends the use of the Secure Erase feature prior to reformatting a used SSD. 7.6 Force Unit Access (FUA) The does not support FUA. 7.7 Spread Spectrum Clocking (SSC) The does not support SSC. 14
8. Pin and Signal Descriptions 8.1 Pin Locations This section identifies the pin locations and signal descriptions of the OCZ High Performance SSD s. 8.2 Hot Plug Support Hot Plug insertion and removal are supported in the presence of a proper connector and appropriate operating system (OS) support as described in the SATA 2.6 specification. This product supports Asynchronous Signal Recovery and will issue an unsolicited COMINIT when first mated with a powered connector to guarantee reliable detection by a host system without hardware device detection. 8.3 Signal Description Table Table 12. No. S1 GND 2 nd mate Plug Connector pin definition Signal S2 A+ S3 A- Differential signal A from PHY 15
No. Plug Connector pin definition S4 GND 2 nd mate S5 B- S6 B+ Differential signal B from PHY S7 GND 2 nd mate Key and spacing separate signal and power segments P1 V33 3.3V power (Unused) P2 V33 3.3V power (Unused) P3 V33 3.3V power, pre-charge, 2 nd mate (Unused) P4 GND 1 st mate P5 GND 2 nd mate P6 GND 2 nd mate P7 V5 5V power, pre-charge, 2 nd mate Power P8 V5 5V power P9 V5 5V power P10 GND 2 nd mate P11 DAS/DSS Device Activity Signal P12 GND 1 st mate P13 V12 12V power, pre-charge, 2 nd mate (Unused) P14 V12 12V power (Unused) P15 V12 12V power (Unused) 16
9. ATA Support The OCZ SSD supports ATA-8 features listed in the table below: Table 13. Feature ATA-8 Reference General 4.2 48-bit address 4.4 General purpose logging (GPL) 4.10 Host protected area (HPA) 4.11 Native command queuing (NCQ) 4.15 Power management 4.18 Security 4.20 S.M.A.R.T. 4.21 TRIM ATA/ATAPI Command Set (ACS-2) 9.1 ATA Command Support The OCZ SSD supports all the commands described in the table below and complies with ATA-8/ACS-2 specification. Table 14. OpCode Command Opcode Command C4h READ MULTIPLE E0h STANDBY IMMEDIATE CAh WRITE DMA EFh SET FEATURES C8h READ DMA 70h SEEK E1h IDLE IMMEDIATE C6h SET MULTIPLE MODE E3h IDLE F6h SECURITY DISABLE PASSWORD E4h READ BUFFER F1h SECURITY SET PASSWORD E5h CHECK POWER MODE F2h SECURITY UNLOCK E7h FLUSH CACHE 39h WRITE MULTIPLE EXT 17
OpCode Command Opcode Command ECh IDENTIFY DEVICE 37h SET MAX ADDRESS EXT F8h READ NATIVE MAX ADDRESS E2h STANDBY FEh VENDOR SPECIFIC COMMAND F3h SECURITY ERASE PREPARE 00h NOP 35h Write DMA EXT 2Fh READ LOG EXT 34h WRITE SECTOR(S) EXT 06h DATA SET MANAGEMENT E6h SLEEP 10h RECALIBRATE 3Dh WRITE DMA FUA EXT 20h READ SECTOR(S) C5h WRITE MULTIPLE 24h READ SECTOR(S) EXT 61h Write FPDMA Queued 25h READ DMA EXT CEh WRITE MULTIPLE FUA EXT 27h READ NATIVE MAX ADDRESS EXT D0h SANITARY ERASE (VENDOR SPECIFIC COMMAND) 29h READ MULTIPLE EXT B0h SMART 30h WRITE SECTOR(S) F5h SECURITY FREEZE LOCK 40h READ VERIFY SECTOR(S) F9h SET MAX ADDRESS 42h READ VERIFY SECTOR(S) EXT F4h SECURITY ERASE UNIT 60h READ FPDMA QUEUED 90h EXECUTE DEVICE DIAGNOSTIC 91h INITIALIZE DEVICE PAREMETERS 92h DOWNLOAD MICROCODE 18
9.2 IDENTIFY Device Data The table below shows 256 words (512 bytes) of sector data returned after the host issues an IDENTIFY DEVICE command. All references comply with ACS-2 specification. Table 15. Word Setting Default Value Description 0 M 0000h 0 = ATA device 1 X 3FFFh Obsolete 2 O C837h Obsolete 3 X 0010h Obsolete 4-5 X 0h Retired 6 X 003Fh Obsolete 7-8 V 0h Reserved for assignment by the CFA association 9 X 0h Retired 10-19 M Varies Serial number (20 ASCII characters) 20-21 X 0000h FFFFh Retired 22 X 3000h Obsolete 23-26 M Varies Firmware revision (8 ASCII characters) 27-46 M Varies Model number (40 ASCII characters) 47 M 8010h Max. number of sectors transferred per interrupt on MULTIPLE commands 48 O 4000h Trusted Computing feature set options 49 M 2F00h Reserved for IDENTIFY packet device command 50 F 4000h Capabilities 51-52 X 0h Obsolete 53 M 0006h Word 88 and 70:64 valid 54 X 3FFFh Obsolete 55 X 0010h Obsolete 56 X 003Fh Obsolete 57-58 X FC10h Obsolete 59 M 0110h Number of sectors transferred per DRQ interrupt on MULTIPLE commands 60-61 M FFFFh 0FFFh Total number of user addressable sectors 62 X 0h Obsolete 63 M 0007h Reserved 64 M 0003h PIO modes supported (ATA only) 19
Word Setting Default Value Description 65 M 0078h Minimum Multiword DMA transfer cycle time per word 66 M 0078h Manufacturer s recommended Multiword DMA transfer cycle time 67 M 0078h Minimum PIO transfer cycle time without flow control 68 M 0078h Minimum PIO transfer cycle time without IORDY flow control 69 O 0D00h Additional supported 70 X 0h Reserved 71-74 F 0h Reserved for the IDENTIFY PACKET DEVICE command 75 O 001Fh Queue depth support 76 O 010Eh Serial ATA capabilities 77 F 0006h Reserved for Serial ATA future definition 78 O 0016h Serial ATA features supported 79 O 0014h Serial ATA features enabled 80 M 03C0h Major Version number 81 M 0000h Minor Version number 82 M 742Bh Command and feature sets supported 83 M 5401h Command and feature sets supported 84 M 4160h Command and feature sets supported 85 M 7469h Command and feature sets supported 86 M 9401h Command and feature sets supported 87 M 4160h Command and feature sets supported 88 O 407Fh Ultra DMA Modes 89 O 000Ah Time required for security erase unit completion 90 O 00C8h Time required for enhanced security erase completion 91 O 0h Current advanced power management 92 O FFFEh Master password revision code 93 M 0h Hardware reset result. The contents of bits (12:0) of this word shall change only during the execution of a hardware reset (see 7.18.7.47) 94 O 0h Vendor s recommended and actual acoustic management value (see 7.18.7.48) 95 O 0h Stream minimum request size 96 O 0h Stream transfer time - DMA 97 O 0h Streaming access latency DMA and PIO 20
Word Setting Default Value Description 98-99 O 0h Streaming performance granularity 100-103 O Varies Maximum user LBA for 48-bit address feature set 104 O 0h Streaming transfer time PIO 105 O 0010h Reserved 106 O 4000h Physical sector size/logical sector size 107 O 0h Inter-seek delay for ISO-7779 acoustic testing in microseconds 108-111 M Varies World Wide Name 112-115 O 0h Reserved for World Wide Name extension to 128 bits 116 O 0h Reserved for INCITS TR-37-2004 117-118 F 0h Logical sector size (see 7.18.7.61) 119 M 4006h Commands and feature sets supported 120 M 400Eh Commands and feature sets supported 121-126 F 0h Reserved for expanded supported and enable settings 127 X 0h Obsolete 128 O 0001h Security status 129-159 O 0h Vendor specific 160 O 0h CFA power mode (see 7.18.7.68) 161-175 O 0h Reserved for the CompactFlash association 176-205 O 0h Current media serial number (60 ASCII characters) 206 O 0021h SCT command transport 207-208 O 0h Reserved for CE-ATA 209 O 4000h Alignment of logical blocks within a larger physical block 210-211 O 0h Write-Read-Verify sector count mode 3 only 212-213 O 0000h 0000h Write-Read-Verify sector count mode 2 only 214 O 0h NV cache capabilities 215 O 0h NV cache size in logical blocks 217 M 0001h Nominal media rotation rate 218-221 F 0h Reserved 222 M 107Fh Transport major revision number 223 M 0h Transport minor revision number 224-233 F 0h Reserved for CE-ATA 234 O 0h Minimum number of 512 byte units per DOWNLOAD 235 O 0h Maximum number of 512 byte units per DOWNLOAD 256-254 F 0h Reserved 21
2.5 Inch Solid-State Drive Word Setting Default Value Description 255 M Varies Integrity word Setting: F/V/X: Fixed/Variable/Undefined Content O/M: Optional/Mandatory Requirement 9.3 Power Management Support The OCZ SDDs supports ATA and SATA power management modes as described below: 9.3.1 ATA Power Modes The ATA power modes supported by OCZ SSDs are: ACTIVE IDLE 9.3.2 SATA Link Power States The SATA power states supported by the OCZ SSDs are: ACTIVE: PHY Ready, full power, Tx & Rx operational 10. S.M.A.R.T. Attribute Support This section describes the S.M.A.R.T. (Self-Monitoring Analysis and Reporting Technology) attributes supported by the OCZ SSDs and the corresponding threshold settings. Table 16. ID 05h 09h 0Ch ABh AEh Description SMART_RELLOCATED_SECTORS_COUNT SMART_POWER_ON_HOURS SMART_POWER_CYCLE_COUNT SMART_OP_AVAIL_COUNT SMART_POWER_CYCLE_UNMANAGED 22
2.5 Inch Solid-State Drive BEh C3h C4h C5h D0h D2h E0h E1h E2h E9h F1h F2h F9h SMART_TEMPERATURE SMART_PROGRAM_FAILURE_BLK_CNT_ID SMART_ERASE_FAILURE_BLK_CNT_ID SMART_READ_FAILURE_BLK_CNT_ID SMART_ERASE_COUNT_AVERAGE SMART_SATA_ERR_CRC SMART_IN_WARRANTY_FLAG SMART_READ_LED_POLARITY SMART_SUPERCAP_FAILURE SMART_REMAINING_LIFE SMART_TCNT_OF_WRITESECTORS_ID SMART_TCNT_OF_READSECTORS_ID SMART_TCNT_NAND_PROGRAM 23
11. Mechanical Specifications Notes: All dimensions are in millimeters. 24
12. Glossary Term ATA ATAPI DMA ECC EXT KB MB Gb GB TB PB GC HDD Hot Plug IOPS LBA TYP MTBF NCQ NOP OS Port P/E UBER SAS SATA SFF Definition Advanced Technology Attachment Advanced Technology Attachment Packet Interface Direct Memory Access Error-Correcting Code Extended KiloByte Mega-byte defined as 1x10 6 bytes Gigabit Giga-byte defined as 1x10 9 bytes Terabyte Petabyte Garbage Collection, can be real time or idle time (background) Hard Disk Drive A term used to describe the removal or insertion of a SATA hard drive when the system is powered on. Input output operations per second Logical Block Address Typical Mean time between failures Native Command Queuing. The ability of the SATA hard drive to queue and re-order commands to maximize execution efficiency. No Operation Operating System The point at which a SATA drive physically connects to the SATA controller. Program / Erase cycles, defines NAND lifecycle Uncorrectable Bit Error Rate Serial Attached SCSI Serial ATA Small Form Factor 25
SMART SSD MLC TRIM Self-Monitoring, Analysis and Reporting Technology: an open standard for developing hard drives and software systems that automatically monitors a hard drive s health and reports potential problems. Solid State Drive Multi-level Cell ATA8 Command informing the drive when sectors no longer contain valid data 13. Revision History Rev. Date By Reason For Change 1.0 October 1, 2014 Product Management Preliminary Release 1.1 March 3, 2015 Product Management Updated Release 1.2 April 14, 2015 Product Management Firmware revision 1.0 release 1.3 June 16, 2015 Product Management Firmware revision 1.01 release 26