D2000 PRO MULTI-INTERFACE TESTER & ANALYZER PRI & BRI ISDN Euro-ISDN standard WAN & DATACOM V.35 & X.21 Tester Flexible Management Full local and remote controlling OVERVIEW FEATURES AT A GLANCE The already affirmed analyzer for ISDN lines made by Aethra, enriches its power with new features in order to answer concretely to all the installation, maintenance and troubleshooting problems. Clear user interface, compact and ergonomic design, quick access mode to the main features. Onboard multi protocol analysis including full frames decoding Internet applications with specific tests for PPP/IP and Frame Relay The integration of new features, gives to D2000 PRO the possibility to expand its working capability allowing to carry out tests over a wide range of applications including Datacom and WAN networks in order to verify SHDSL, HDSL and the Internet cloud. All these points make the D2000 PRO a complete multi-interface tester and analyzer. Includes PC108 for Windows software for powerful analysis and remote management Memory expansion through standard MultiMediaCard The D2000 PRO offers a graphic interface with common characteristics to the whole new generation test equipments family made by Aethra so, it is possible to use the entire equipments range as the navigation procedures through the various menu remain unchanged. All the information necessary to verify the line status and the possible presence of troubles on the line, is within a button s reach, thanks to the immediate access to Smart Status feature. The access to such a feature is always available also during the carrying out of a test, allowing so to have always under control monitoring over layer 1, 2 and 3, alarms, errors, channels configurations and the test in progress modes, as well as the device status itself. Onboard multi language GUI, including special fonts In field upgradable firmware
INTERFACES Thanks to D2000 PRO s capability of working on a wide series of interfaces with the same simplicity, immediacy and processing capability, it can be considered as one of the most versatile device existing on the market. Besides the most commonly used accesses such as Basic Rate, Primary Rate and POTS, the measures may be carried out also over leased circuits WAN/datacom 3 thanks to VX2000 adapter. Basic Access ISDN S0/T0 Basic Access ISDN Uk0 2B1Q and 4B3T Primary Access ISDN IDSL (64Kbps 128 Kbps) G.703 (2Mbps) G.704 (Nx64Kbps) V.35 3, V.36 3 and V.11-X.21 3 POTS 5 MONITOR The device captures the main communication protocols over D and B channel. The onboard decoding allows to analyze traces directly at the user s site. The advanced analysis through the PC software 1 issued with the device, helps to solve also more complex problems regarding ISDN connections or user s Internet settings. The feature is available both as high impedance monitor and simulator. If necessary, data may be saved into a normal MultiMediaCard, expanding the internal memory. D & B channel monitor U-Bus monitor Capturing filters Statistics information E-DSS1, 1TR6, X.25, VN4, Q.SIG, DASS2, DPNSS, CorNet V.5.1/V.5.2 decoding 1 PPP/IP and FRAME RELAY decoding 1 MultiMediaCard memory support 2 BER D2000 PRO can be used everytime quality line checking is needed. Bit Error Rate includes results valuation according to G.821 and G.826 regulations. Measures may be carried out both over Basic Rate Access and Primary Access as well as over WAN G.703, G.704 interfaces. With the new VX2000 adapter tests are extended also to datacom circuits V.35 3, V.36 3 and V.11-X.21 3. G.821 G.826 Different test patterns Test modes End-to-End and Selfcall N*64k mode Bearing physical layer quality test Multiple measurement cycles MAKE A CALL
MAKE A CALL Using the multi-functional Make a Call test, it is possible to verify the correct operation of the several supplementary services supplied by provider, such as AOC, CF, CLI, 3PTY and all the other common ones. People working with PABX will find very useful the possibility to generate more calls simultaneously with several numbers and profiles; making the PABXs setting up faster and very functional. In order to solve the problems concerning data connection such as video-conferencing, the test makes available the round trip delay of B channel in milliseconds. Integrated microphone and loudspeaker, allow to use the device also as a normal ISDN or POTS 5 telephone. ETSI supplementary services check and support B channel round trip delay Multiple profiles (Speech, Data, Fax,..) Up to 30 active calls 4 B channel connected to incorporated micro phone and loudspeaker o external handset or V.11 interface ISDN and POTS 5 simulation X.25/X.31 D2000 PRO is able to perform an X.25/X.31 connection over D channel and verify the quality of the line. Now the test allows to simulate an X.25 traffic generation also over B channel, using programmable data packets with variable length. Statistic Data help to check out the real band of the connection and possible net congestion problems. Through the software provided 1, it is possible to send pre-configured packets directly from the personal computer. D and B channel X.25/X.31 support DTE and DCE simulation Programmable transmission throughput Variable data packet length Working over Vc and PVc circuits Vc and PVc automatic recognition in incoming mode Traffic statistics IP D2000 PRO expands its own applications field to the Internet world, thanks to two tests implemented into the standard version of the device. The first, IP PING, allows to check the connection to the Internet Provider, the reachability of a remote host and the relative response times. Moreover, all the information coming from the server are provided such as messages and local, remote and server IP addresses. This allows to check out the correct connection settings of the user. The second test, IP GENERATE TRAFFIC, allows to simulate a data transfer between hosts. This test, more exhaustive than IP PING, is able to measure the throughput of the connection in progress. PPP, IP, UDP, ICMP, TFTP support Authentication PAP and CHAP (MD5) IPaddress static and dynamic Programmable packet length Testing file length up to 16Mbytes Multiple measurement cycles IPstatistics and times Calculation of the throughput in transmission and reception path IPaddress book, password and UserID in order to login immediately to Internet To perform the test, it is not required a second device 6 Simulation Monitor
FRAME RELAY Through a specific option, D2000 PRO may be used for commissioning and maintaining Frame Relay services. The test can be carried out over E1, G.703 and V/X interfaces. Turn-up test for verification of link connectivity and configuration IPPing test QoS statistics GENERATE TRAFFIC This traffic simulation permits to verify the call management capabilities on behalf of the user system (PABX) or of the net. The load simulated, may be programmed by quantity of calls to perform and duration time. Up to 999 failure cycles are stored reporting causes and times. Up to 30 simultaneous calls 4 Programmable time between calls Maximum 65000 test cycles Settable minimum call duration Test cycles on connection or B channel notification UTOMATIC TESTS AUTOMATIC TEST This test allows an automatic and immediate verification of the line under measurement both for ISDN and X.25 service. If not otherwise specified, the device generates automatically a series of calls toward a remote user or in autocall mode and verifies the complete status of the line both for BRI and PRI. With the possibility to set up and save a personalized test sequence, the control of several line typologies is easier and more immediate. It is possible to set a complete automatic test or individual layers or services to verify Physical layer settings control Layer 2 configuration Availability status of the several bearer services, teleservices and supplementary services Availability checking of single B channels TEI and LCI detection for X.25 (X.31) service MISCELLANEOUS The device owns a powerful automatic answering feature to incoming calls. The technician can set such feature in order to filter acceptable incoming calls, performing a loop over data or a call back toward the calling user. The forward capability and the possibility to answer manually the incoming calls, enlarge the using potentialities of such feature in verification and stressing tests of the user s systems. Loopbox Call back and Call Forward Features for Single End Tests Programmable U-Bus load S/T-Bus wiring test 7 Protected Monitor Point 1 Pc108 for Windows 2 MMC2000 3 VX2000 4 PRI 5 AB2000 6 Requires TFTP server on remote host 7 WT2000
TECHNICAL SPECIFICATIONS TELECOM INTERFACES Basic Rate Access S/T ITU-T (CCITT) Rec.I.430, ETS 300 012 U 2B1Q and 4B3T,TS 102 080 Primary Rate Access E1 ITU-T (CCITT) Rec.I.431, ETS 300 011 Primary WAN / datacom 2Mbit CCITT G.703 / G.704 V.11, X.21 ITU-T (CCITT) Rec.V.11 V.35 ITU-T (CCITT) Rec.V.35 V.36 ITU-T (CCITT) Rec.V.36 PROTOCOLS SUPPORTED Simulation mode Monitor mode Other protocols available by PC EDSS-1, Q.SIG, 1TR6, TN1R6, VN4, X.25, X.31, DASS-2, DPNSS, CorNet -N, -NX, -NQ, -T, PPP, IP, UDP, DHCP, ICPM, TFTP, Frame Relay EDSS-1, Q.SIG, 1TR6, TN1R6, VN4, X.25, X.31, DASS-2, DPNSS, CorNet -N, - NX, -NQ, -T V.5.1, V.5.2, NI1, DMS100, 5ESS OPERATING MODES AVAILABLE BRI TE-S BRI MON-S BRI NT-S BRI NT-U BRI MON-U D2022 option BRI LT-U LTU-2K option BRI S /T-Bus wiring test WT2000 option PRI TE-E1 PRI MON-E1 PRI MON-E1 PMP D2021 option PRI NT-E1 POTS TE AB2000 option POTS MON AB2000 option V/X DTE VX2000 option V/X DCE VX2000 option SMART STATUS Physical layer G.826 / M.2100 (Only PRI) All physical Layer relevant information ES, SES, BBER, UAS, both in simulation and monitor ISDN line ISDN Layer 1, 2 and 3 status clearly shown. B channels All B channel s relevant information V/X interface [VX2000] Control leads, test running, loop, clock frequency, clock phasing Frame Relay [FR2K] DLCI, LMI, and quality test BACKGROUND MONITOR Modes Protocol analysis on-board Programmable filters Statistics information Analysis of the results stored on PC ADVANCED LOOP-BOX FEATURES AUTOMATIC ACCESS TEST Fully automated Access test Supplementary services automatic test Programmable test sequence BIT ERROR RATE TEST G.821 statistics High impedance and during simulation Independent filters capturing and displaying PC108 for Windows ES, SES, US, DM, PASS/FAIL, S-LOSS Pseudo-Random bit sequences User definable 2 11-1,2 15-1,2 23-1, octet 16 bit Error Injection Round trip delay User selectable, manual, automatic, single GENERATE TRAFFIC Number of cycles Up to 65535 Number of parallel calls Up to 30 (PRI) Delay between calls User selectable X.25/X.31 Modes Logical Types Tests IP Modes IP address supported Authentication protocol PPP Protocols FRAME RELAY [FR2K] Frame Relay Forum Type of traffic LMI Physical Logical Types QoS statistics SVC, PVC DTE, DCE Traffic generator, Echo port IP routed, IP over PPP (Client and Server) Static, Dynamic PAP, CHAP (MD5) IPv4, UDP, DNS, DHCP CMP, TFTP FRF.1.1, FRF.3.1, FRF.12.1, FRF.14 IP, IP over PPP ITU-T Q.933, ANSI T1.617, original LMI CISCO G.703,G.704,V.35,V.36,V.11-X.21 UNI, CPE, NNI FECN, BECN, DE, NLPID, DLCI, FRF.12 U-BUS LOOP QUALIFICATION U-Bus voltage measurement Loop resistance measurement (Ω) Programmable simulation NT-load over U-Bus Activation/Deactivation time measurement (msec.)
HISTORY AND PREDEFINED TESTS FEATURES Saving and recalling of 10 different setup and results for each kind of test CONNECTORS S/T Basic Access interface RJ45 (ISO 8877) U Basic Access interface RJ45 (ISO 8877) Primary Access interface RJ45 120 Ohm, BNC 75 Ohm RS232 DB-9 (V.28 CCITT ISO4902) Handset 4 wires RJ9. Balanced, 600Ω Power in External AC/DC adapter Power out Mini-DIN 4 wires connector ENVIRONMENTAL CHARACTERISTICS Dimension Weight, with battery 1 kg Dimensions, with holster (mm) 130 (w) x 260 (l) x 65 (d) Power Battery Type Rechargeable, Ni-MH Battery life 3 hours @ 25 C,LCD back-lit off External AC/DC adapter 115/230Vac ±10% @ 50/60 Hz MISCELLANEOUS LCD display 240x200 Graphic display wide bright an back-lit Internal microphone & loudspeaker Upgradable firmware MultiMediaCard memory extension MMC2000 Option OPTIONS WT2000 AB2000 LT-U2K D2022-Q D2022-T MMC2000 VX2000 DTE CABLE KIT for VX2000 DCE CABLE KIT for VX2000 FR2K BCH108 S0/T0 wiring test POTS line adapter BRI LT-U simulation BRI U (2B1Q) interface monitor BRI U (4B3T) interface monitor Memory extention DTE/DCE Datacom tester DTE simulation DCE simulation Frame Relay test suite Multi protocol decoding for PC108 for Windows TM TEMPERATURE Storage/Transport - 40 o C to +70 o C Operating,nominal - 5 o C to +45 o C Operating, limits -10 o C to +55 o C Humidity, non-condensing 93% RH @ 40 o C 70% RH @ 55 o C User's Safety Aspects EN 61010-1,EN 60950, EN 41003 EMC Aspects EN 55022, EN55024, EN 61000-3-2 / -3-3 CE Marking Class B (residential devices) Aethra SpA Telecommunications via Matteo Ricci 10 60020 Ancona - Italy Telephone +39.071.218981 Fax +39.071.887077 Video 1 +39.071.2189160 Video 2 +39.071.2189701 Email: info.aethra@aethra.com www.aethra.com Aethra, Inc. 701 Brickell Avenue Suite 1390 Miami, FL 33131 USA Telephone +1.305.375.0010 Toll Free (US only) 1.888.4.AETHRA Fax +1.305.375.0655 Video +1.305.577.3524 Email: info.na@aethra.com Aethra, the Aethra logo, the D2000 PRO and Smart Status TM are trademarks, registered trademarks, or service marks of Aethra SpA Telecommunications in Italy, the United States, and/or other countries. All other company and product names may be registered trademarks or trademarks of their respective owners. Information furnished by Aethra SpA Telecommunications and Aethra, Inc. in this datasheet is believed to be accurate. Products sold and licensed by Aethra SpA Telecommunications and Aethra, Inc. are covered by warranty and patent indemnification provisions appearing in its purchase and license agreements. Aethra SpA Telecommunications and Aethra, Inc. reserve the right to discontinue production and change specifications and prices at any time without notice. Copyright 2003 Aethra SpA Telecommunications - All rights reserved. Additional regional offices are located on our website: www.aethrausa.com. For further details about technical specifications please see Products on www.aethra.com Code 071102000GB Rev.0 (06/03)