Specifications for Rotating Anode X-ray Tube Ass y. Model : M125S20X. Maximum X-ray Tube Voltage kV. Focal Spot Size (Small/Large) /2.
|
|
- Neal Holmes
- 5 years ago
- Views:
Transcription
1 Specifications for Rotating Anode X-ray Tube Ass y Model : Maximum X-ray Tube Voltage kV Focal Spot Size (Small/Large) /2.0mm Anode Heat Content kJ(140kHU) X-ray Tube Ass y Heat Content kJ(1,250kHU) Min. Anode Rotation Speed(60Hz)... Min. 3,200rpm DOC no Date Rev RD
2 GENERAL SPECIFICATION 1. Product Information 1.1 Short Description Intended use: X-ray tube assembly with double-focus rotating anode X-ray tube is intended to be used for diagnostic X-ray equipment. 125kV, 140kHU rotating anode insert tube which is designed for general radiographic procedures. - Tungsten-rhenium alloy faced TZM target of 16º and 74mm diameter - Available in the 1.0mm / 2.0mm focal spot combinations - Stator of min. 3200rpm rotation speed 900kJ heat content of X-ray tube ass y Accommodated with IEC60526 type high voltage cable receptacles. 1.2 Designation of each part of tube assembly Page 2
3 2. General Data 2.1 Electrical Data Nominal X-ray Tube Voltage kv Operating X-ray Tube Voltage kV Nominal Focal Spot Size Large mm Small mm Anode Rotating Speed 50Hz... Min. 2,700 rpm 60Hz... Min. 3,200 rpm Stator Resistance Main Winding Ω Auxiliary Winding Ω Stator Capacitor μf Resistance Between Housing and Low Voltage Terminals... Min. 2 MΩ Nominal Anode Input Power Focus 50 Hz 60 Hz Large 43 kw 47 kw Small 21 kw 22.5 kw Normal Housing Operating Temperature Page 3
4 2.2 Mechanical Data Overall length mm Detail Dimensions... See page 8 Approximate Weight kg Target Diameter mm Anode Angle degree Material... Tungsten-Rhenium faced TZM Filtration Permanent Filtration mm Al / 75 kv Radiation Protection Leakage Technique Factor kv, 4 ma X-ray Coverage (at SID 750 mm ) mm High Voltage Receptacle... To meet requirements of IEC60526 Cooling Method... Natural air 2.3 Environmental Limits Operating Limits Temperature Humidity % Atmospheric Pressure kpa Shipping and Storage Limits Temperature Humidity % Atmospheric Pressure kpa Page 4
5 3. Max. and Min. Ratings (Maximum Design Value) Max. X-ray Tube Voltage kv Max. Voltage to Ground kv Min. X-ray Tube Voltage kv Max X-ray Tube Current Large ma Small ma Max. Filament Current A Filament Voltage (at max. filament current 5.1A) Large V Small V Filament Frequency Limits khz Thermal Characteristics Anode Heat Content kj (140 khu) Max. Anode Heat Dissipation W (667 HU/s) X-ray Tube Ass y Heat Content kj (1250 khu Max. Continuous Heat Dissipation Without Air-circulator W (15 khu/min) Page 5
6 4. Max. Rating Charts 4.1 Stator Frequency : 60 Hz [Focal Spot : 1.0mm ] [Focal Spot : 2.0mm ] Tube Current ( ma ) 70kV 60kV 50kV kV 90kV 40kV kV kV 125kV Tube Current ( ma ) 100kV kV 80kV 70kV 60kV 50kV 110kV kV 125kV Exposure Time (sec) Exposure Time (sec) 4.2 Stator Frequency : 50 Hz [Focal Spot : 1.0 mm ] [Focal Spot : 2.0 mm ] kV 60kV 50kV kV 80kV 70kV 60kV 50kV kV 90kV 40kV kV 110kV 40kV Tube Current ( ma ) kV 110kV 125kV Tube Current ( ma ) kV Exposure Time (sec) Exposure Time (sec) Page 6
7 5. Emission and Filament Characteristics 5.1 Focal Spot : 2.0 mm Tube Current ( ma ) Filament Voltage (V) Filament Current (A) 5.2 Focal Spot : 1.0 mm Tube Current ( ma ) Filament Voltage (V) Filament Current (A) Page 7
8 6. Thermal Characteristics 6.1 Anode Heating and Cooling Curves Heat Storage (kj) Time (minutes) 6.2 X-ray Tube Ass y Heating and Cooling Curve Heat Storage (kj) Time (minutes) Page 8
9 7. Detail Dimensions [Unit : mm ] Anode Central Ray and Reference Axis Large Small Cathode Common Central X-ray Terminal Connections E Focal Spot A A : ±1.5 mm, B : ±1.5 mm Center of Focal Spot B Non-connection Temperature Relay (Normally Closed) C M A C : Common M : Main Winding of the Stator A : Auxiliary Winding of the Stator Earth Terminal Non-connection [Note] Do not connect terminal No.1 and No.5 or 6 in series circuit. Page 9
10 8. Symbols 8.1 Symbols marked on Symbol Description CE Marking of Conformity Serial Number: This symbol means serial number of product. Manufacturer information: The manufacturer s information shows with this symbol. Made Date: The made date of the product shows with this symbol Protective earth symbol: This symbol means Protective earth terminal Representatives information: The manufacturer s EU representative information shows with this symbol.! Warning or Caution: This symbol indicates hazard. Electronics Disposal Information: This symbol means that the product should be recycled separately from household waste. When this product reaches its end of life, follow the local laws and regulations of disposal. The improper disposal of waste electronic equipment from the consumer may be subject to fines. Page 10
11 8.2 Symbols on the Packaging of Symbol Description KEEP DRY: This symbol means keep away from Rain Fragile : This symbol means do not drop of product. UP: This symbol means "This way up". Page 11
12 9. Label Location 9.1 Front Page 12
13 9. Label Location 9.2 Rear Page 13
14 10. Cautions 1) Caution for Installation, Adjustment and Maintenance Qualified Persons : Only qualified persons who have technical training and professional knowledge can handle X-ray tube assembly. Fragile Glass : X-ray tube is assembled with glass, therefore, it can be broken with the mechanical vibration or pulsed shock over 19.6m/(2G). Careful handling is required to treat or transport. Ground Terminal : X-ray tube assembly has ground terminal. Ground cable should be connected. High Voltage : All X-ray tubes operate at voltages high enough to kill through electric shock. Never touch the high voltage delivered plugs or terminals. When direct access to such parts is required, the primary circuit should be disabled and high voltage capacitors/cables discharged. High Voltage Plug : High voltage plug should be cleaned up and free from any physical damages. Silicon compound application is required for high voltage stability. Rotating Anode - Test rotation of the anode with the large focus filament at the preheat condition. At this time, do not supply the tube voltage. - When the hand switch READY button is pressed, the filament will become brighter and the anode target will start rotating. The anode for normal speed will reach the predetermined number of revolution in 0.4 to 1 sec., and it will continue rotation for some time after the stator drive input is cut off. The anode for high speed shall be automatically braked to reduce speed and continue coasting after the drive input to the stator is cut off. - Ensure that the anode target rotates in the proper direction. X-ray tube should always rotate counter-clockwise, viewing from the cathode side. Operation Atmosphere : X-ray tube assembly is not allowed to use in the atmosphere of flammable or corrosive gas. Protective Cover : X-ray tube assembly is not allowed to use without the protective cover Handling : Appropriate jigs or tools are required for tube installation to avoid physical damages. Returning Tube : X-ray tube assembly should be repacked with the original material when it is returned back for quality examination in our factory. Be careful to put the tube upside cathode. If the packaging is not proper, the tube may not be correctly examined. Page 14
15 2) Caution to interface with X-ray Generator Over Rating : X-ray tube assembly can be broken with applying just one over rated shot. Please read the specification sheets carefully and follow the instructions. Permanent Filtration : The total filtration and the distance between X-ray focal spot and human body are regulated legally. They should be complied with the regulation. Safety Thermal Switch : X-ray tube assembly has safety thermal switch to prohibit further input power when the tube housing reaches to the temperature of switch-open. The switch should be hooked up with the X-ray generator which control output power to X-ray tube assembly. The switch is not recommended connecting stator coil in series circuit. Even if the switch works, never turn the system power off. The cooling unit should be activated if used with the system. Safety Plate : The Safety Plate is mounted on anode housing wall. When external cover is removed, it is visibly recognized as labeled with label 8 in Caution Labels page. Followings are important notice of the Safety Plate: - Function : When housing inner pressure reaches to the working pressure of the Safety Plate, the Safety Plate collapses and vaporized oil and hot oil flow through the collapsed Safety Plate. The external cover can protect the initial impact of oil flow, however, it can not protect oil drop or oil leakage. - Caution : Never touch the Safety Plate or remove the label and the screws. Otherwise, it could cause collapse of Safety Plate. Please note the Safety Plate is not the device to protect X-ray tube from destruction when over-rated power input but just to reduce the impact of housing rupture. Unexpected Malfunction : X-ray tube assembly may have the risk to be unexpectedly malfunctioning due to life termination or failure. If the serious problems caused by the above risk are expected, you are requested to have a contingency plan to avoid such a case. New Application : If you use the product with new application not to be mentioned in this specification or with different type of X-ray generator, please contact to us for confirming its availability. Page 15
16 3) Periodical Inspection To maintain long-time stable operation and service life, perform the periodical inspection at every regular intervals (at least once a year) in accordance with the items described on the following page. For any inspection items, if necessary, instruct LUCEM Co.. Ltd. personnel to carry out the periodical always operation the silicone compound may become dry, the coated state changed or the withstand voltage performance degraded. Insulation oil leakage from tube housing Thermal switch operation of the tube assembly High voltage cable connection part - Looseness of cable plug camping part - Silicone compound leakage and state of coating Roughness and bulb spatter on the target surface of the X-ray tube. Extremely abnormal noise and or vibration due to X-ray tube anode rotation Abnormal rotation of the air circulator of the tube assembly. Grounding wire and grounding resistance. Indication of tube voltage meter, tube current meter, and other meters. Timing phase deviation and time accuracy of the exposure timer. Operation of the starter for the tube assembly. Brightness and image quality of X-ray image intensifier. 4) Others X-ray tube ass y should have the -ray X limiting equipment mounted on the X-ray port to protect unnecessary radiation. X-ray tube ass y is not allowed is not allowed to use in the atmosphere of flammable or corrosive gas. If the input power exceeds X-ray tube ass`y specification, it cause the over temperature of anode, insert tube glass shatter, housing sealing parts rupture, human injury including burns due to hot oil escape and fire accident due to flaming anode target. The X-ray generator should have a protective function which manages input power to be within X-ray tube ass y specification. X-ray tube ass y is covered with lead inside tube housing to protect unnecessary radiation. The lead is harmful for human health. Dispose the scrapped products according to the requirement of local regulation. Page 16
17 X-ray tube ass y has insulation oil contained for high voltage stability. The insulation oil is poisonous for human health. If it is exposed to the non-restricted area, it should be disposed as following to the local regulation. According to the operating conditions, the filament characteristics might be changed to lead to the over rate exposure to X-ray tube ass y. To prevent the X-ray tube ass y from being damaged, please adjust the tube current regularly. Please don t touch on X-ray tube ass y just after operation due to high temperature. X-ray tube assembly is not allowed to lift more than 1 meter during transportation. X-ray tube assembly is not allowed to stack more than 2 stories. If any malfunction of the X-ray tube ass y is noticed, please contact to us immediately. Avoid fire and explosion hazard. An explosion hazard may result from the use of flammable anesthetics, skin cleansing agents and disinfectants. When cleaning the device, pay special attention so that cleaning liquid or any liquid may not soak into the inside of device. If any liquid soak into the inside of device, do not connect power line, do not use device, and contact service center. This equipment produces ionizing radiation. Observe proper safety practices during operation. The requirement to wear personal protective equipment such as lead aprons, dosimetry badges etc is governed by individual states and may vary from state to state. Other safety information follows the product-mounting system information. The tube assembly contains a high-vacuum product that can implode on incorrect handling, such as by impact, striking, dropping down. Use of the X-ray tube assembly is forbidden if signs of mechanical, electrical or radiation-related defects are present. WARNING: To avoid the risk of electric shock, this equipment must only be connected to a supply mains with protective earth. Page 17
Voltage nominal maximum for test. Inverse voltage. nominal maximum for test. Focal spots (IEC 60336:2005) small large
TECHNICAL DATA GENERAL INFORMATIONS Voltage nominal maximum for test 1 135 kv When mounting tube inserts adopt proper caution, in order to avoid glass bulb breaking and fragments projection. Please use
More informationIn the previous presentation, we discussed how x-rays were discovered and how they are generated at the atomic level. Today we will begin the
In the previous presentation, we discussed how x-rays were discovered and how they are generated at the atomic level. Today we will begin the discussion on the major components of the x-ray machine. Today
More informationX-ray Imaging Systems
Principles of Imaging Science I (RAD 119) X-ray Tube & Equipment X-ray Imaging Systems Medical X-ray Equipment Classified by purpose or energy/current levels kvp, ma Radiographic Non-dynamic procedures
More informationFLUORESCENT UV- RING LIGHT OPERATING INSTRUCTION
FLUORESCENT UV- RING LIGHT OPERATING INSTRUCTION Caution! UV-radiation of this device is in the range of UV-A (320-400 nm). Direct exposure to eyes shall therefore be avoided. UV protection glasses shall
More informationX-ray Imaging Systems
Principles of Imaging Science I (RAD 119) X-ray Tube & Equipment X-ray Imaging Systems Medical X-ray Equipment Classified by purpose or energy/current levels kvp, ma Radiographic Non-dynamic procedures
More informationMICA HEATER INSTRUCTION MANUAL Model No: UHM-786 230V 50Hz 2200W
MICA HEATER INSTRUCTION MANUAL Model No: UHM-786 230V 50Hz 2200W Safety Precautions To reduce the risk of personal injury or damage to property, basic safety precautions must be observed including the
More informationUV100A Ultraviolet Air Treatment System
UV100A Ultraviolet Air Treatment System INSTALLATION INSTRUCTIONS APPLICATION When installed in forced air heating and cooling systems, the UV100A Ultraviolet Air Treatment System kills airborne microorganism
More informationCAUTION OPC-LM1-IL. Option Card for Encoder of Line Driver Output. Instruction Manual
Instruction Manual OPC-LM1-IL Option Card for Encoder of Line Driver Output CAUTION Deliver this instruction manual without fail to those who actually operate the equipment. Read this operation manual
More informationThank You... On behalf of the entire team at Thane Housewares, we appreciate your recent purchase
User s Guide Thank You... On behalf of the entire team at Thane Housewares, we appreciate your recent purchase of the FLAVORCHEF cooking system, which will provide you with healthy and tasty meals for
More informationUSER S MANUAL. MaxPower 400-600 UPS. Uninterruptible Power System 28-2MAXPO0018
USER S MANUAL MaxPower 400-600 UPS Uninterruptible Power System 28-2MAXPO0018 IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This manual contains important instructions for models MaxPower 400 and
More informationSpec. No. ICR18650-26C Version No. 0.0
1. Scope This product specification has been prepared to specify the rechargeable lithium-ion cell 2. Description and Model 2.1 Description Cell (lithium-ion rechargeable cell) 2.2 Model ICR18650-26C 3.
More informationINFRARED QUARTZ WALL HEATER
INFRARED QUARTZ WALL HEATER MODEL NO: IQ2000 PART NO: 6939004 MOUNTING & OPERATION INSTRUCTIONS GC0715 INTRODUCTION Thank you for purchasing this CLARKE Infrared Wall Heater. Before attempting to use this
More informationCAUTION OPC-LM1-ID. Option Card for Frequency Divider. Fuji Electric FA Components & Systems Co., Ltd. Instruction Manual
Instruction Manual Option Card for Frequency Divider Deliver this instruction manual without fail to those who actually operate the equipment. Read this operation manual and understand the description
More informationWSD130 SOLDERING STATION
NOTES S2032ACH 8/98 Rev. 11/01 WSD130 SOLDERING STATION 1. Power Switch 2. Digital Display 3. UP Button 4. DOWN Button 5. Optical Regulator, Right 6. Connection for Soldering Iron, Right 7. Selection Switch
More informationAIR-CONDITIONER SPLIT TYPE
FILE NO. A08-016 SERVICE MANUAL AIR-CONDITIONER SPLIT TYPE RAS-M10PKVP-E, RAS-M13PKVP-E, RAS-M16PKVP-E, RAS-M18PKVP-E / RAS-M10PKVP-ND, RAS-M13PKVP-ND, RAS-M16PKVP-ND, RAS-M18PKVP-ND / RAS-3M26GAV-E1,
More informationSECTION 1: REQUIREMENTS FOR CERTIFICATES OF COMPLIANCE FOR CLASSES OF RADIATION SOURCES
Department of Health and Human Services Population Health Radiation Protection Act 2005 Section 17 CERTIFICATE OF COMPLIANCE: STANDARD FOR RADIATION APPARATUS - X-RAY DIAGNOSTIC (VETERINARY) SECTION 1:
More informationUser s Manual Before using the inverter, you need to read and save the safety instructions.
User s Manual Before using the inverter, you need to read and save the safety instructions. STI SERIES (STI200, STI300, STI500, STI700, STI1000) Power Frequency Pure Sine Wave Inverter The information
More informationADM1TE 5/30A DIN rail single phase two wire energy meter
ADMTE 5/30A DIN rail single phase two wire energy meter. Safety instruction.2 Foreword.3 Performance criteria.4 Specifications.5 Basic errors.6 Description.7 Dimensions.8 Installation.9 Operating.0 Troubleshooting.
More informationThe table below lists the symbols used on the Clamp and/or in this manual. Important Information. See manual.
i800 AC Current Clamp Instruction Sheet Introduction The i800 AC Current Clamp, the Clamp, has been designed for use with multimeters, recorders, power analyzers, safety testers, etc., for accurate non-intrusive
More informationTIG INVERTER INSTRUCTION MANUAL
TIG INVERTER INSTRUCTION MANUAL Contents Warning General Description Block Diagram Main Parameters Circuit Diagram Installation and Operation Caution Maintenance Spare Parts List Troubleshooting 3 4 4
More information=============================== WARNING
=============================== WARNING EXPLANATION OF GRAPHICAL SYMBOLS This symbol is intended to alert the user to the presence of unprotected dangerous voltage" within the product's enclosure that
More informationIMPORTANT SAFETY INSTRUCTIONS WARNING READ AND SAVE THESE OPERATING AND SAFETY INSTRUCTIONS BEFORE USING THIS HEATER.
THERMAWAVE CERAMIC HEATER Model HZ-850 Series Model HZ-860 Series IMPORTANT SAFETY INSTRUCTIONS WARNING READ AND SAVE THESE OPERATING AND SAFETY INSTRUCTIONS BEFORE USING THIS HEATER. Warning Failure to
More informationMOUNTING AND OPERATING INSTRUCTIONS
MOUNTING AND OPERATING INSTRUCTIONS CF 51/55 1. Delivery CF 51/55-1 calculator with battery (optionally with mains power supply) - 1 wall mounting bracket - package with material for sealing, screws, wall
More information15GAL STEEL OIL DRAIN WITH 110V PUMP
15GAL STEEL OIL DRAIN WITH 110V PUMP OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety
More informationHow To Use A Power Supply Unit (Upu)
BRAVER UPS (Uninterruptible Power System) User s Manual Safety CAUTION! This UPS utilizes voltages that may be hazardous. Do not attempt to disassemble the unit. The unit contains no user replaceable parts.
More informationDaker DK 1, 2, 3 kva. Manuel d installation Installation manual. Part. LE05334AC-07/13-01 GF
Daker DK 1, 2, 3 kva Manuel d installation Installation manual Part. LE05334AC-07/13-01 GF Daker DK 1, 2, 3 kva Index 1 Introduction 24 2 Conditions of use 24 3 LCD Panel 25 4 Installation 28 5 UPS communicator
More informationDRM75A 230V 20/100A DIN rail single phase two wire energy meter
DRM75A 230V 20/100A DIN rail single phase two wire energy meter 1.1 Safety instruction 1.2 Foreword 1.3 Performance criteria 1.4 Specifications 1.5 Basic errors 1.6 Description 1.7 Dimensions 1.8 Installation
More informationOWNER S MANUAL BIG BEAR VORTEX FAN MODEL #BB-1 INTRODUCTION OPERATION SAFETY SERVICE WARRANTY CONTACT SPECIFICATIONS TROUBLESHOOTING
OWNER S MANUAL BIG BEAR VORTEX FAN MODEL #BB-1 INTRODUCTION OPERATION SAFETY SERVICE WARRANTY CONTACT SPECIFICATIONS TROUBLESHOOTING PLEASE READ AND SAVE THESE INSTRUCTIONS - 2 - INTRODUCTION TO THE BIG
More informationInfrarot-Bewegungsmelder IP44
Infrarot-Bewegungsmelder IP44 infrared motion sensors IP44 ODA (weiß) slim ODA (schwarz) slim 95174 96000 ODA (weiß) ODA (schwarz) 95175 96001 Betriebsanleitung User s Manual User s Manual infrared motion
More informationUltrasonic support removal tank
Ultrasonic support removal tank User guide and safety manual See inside for use and safety information. The Ultrasonic support removal tank automatically removes PLA support material from a printed ABS
More information3 WATT LED SPOTLIGHT Model No. SLM - 3801
3 WATT LED SPOTLIGHT Model No. SLM - 3801 OWNER'S MANUAL Customer Service Tel: 1-800-268-3319 Superex Canada Ltd, Toronto,M2H 3B8 Made in China Table of Contents A). Important Safety Instructions B). Charging
More informationModel 1756 Test Lead Kit
Keithley Instruments 28775 Aurora Road Cleveland, Ohio 44139 1-888-KEITHLEY http://www.keithley.com Model 1756 Test Lead Kit Gerneral Purpose Test Lead Information Description These test leads allow you
More informationSBC90. Abrasive Blast Cabinet Assembly & Operating Instructions
SBC90 Abrasive Blast Cabinet Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. This manual provides important
More informationSpecification Approval Sheet
GUANGZHOU MARKYN BATTERY CO., LTD. Specification Approval Sheet FOR LIPO BATTERY Product Name Model SPEC Company Name Document Number Li-ion Polymer Battery 062025/250mAh/3.7V GMB POWER GMB1102150615 Sample
More information12V Portable Diaphragm Compressor Operating and Maintenance Instructions
12V Portable Diaphragm Compressor Operating and Maintenance Instructions (Part No. DC2) Part No. Serial Number Date Purchased Table of Contents Page Safety Messages...2 Guidelines for Product Use...2 Operation
More informationTECHNICAL DATA & SERVICE MANUAL SPLIT SYSTEM AIR CONDITIONER INDOOR UNIT: AW52AL AW64AL AW52AL 387030095 AW64AL 0.8180.463.0 07/05
TECHNICAL DATA & SERVICE MANUAL INDOOR UNIT: AW52AL AW64AL SPLIT SYSTEM AIR CONDITIONER Model No. Product Code No. AW52AL 387030095 AW64AL 387030096 0.8180.463.0 07/05 IMPORTANT! Please read before installation
More informationInstallation and safety instructions for AC/DC built-in devices
The device type and date of manufacture (week/year) can be found on the device rating plate. In the event of any queries about the device, please quote all the details given on the rating plate. For further
More informationNational- Spencer Inc.
9-27-2010 National- Spencer Inc. 19.2V HEAVY DUTY GREASE GUN PRODUCT SPECIFICATION Charger Input Power 110 VAC Battery Output Power 19.2V Battery Capacity 1500 MAH Battery Pack Charge Time 1 Hour Maximum
More informationLITHIUM BATTERY CR123A SPECIFICATION
LITHIUM BATTERY CR123A SPECIFICATION Date: April 24, 2012 Approved by: Scotty Scott PANASONIC ENERGY CORPORATION OF AMERICA LITHIUM BATTERY DIVISION 1. Designation : CR123A 2. Nominal Voltage : 3 V 3.
More informationKolorlux. GE Lighting DATA SHEET
GE Lighting Kolorlux High pressure Mercury lamps Kolorlux Standard 50W, 80W, 125W, 250W and 400W Kolorlux Deluxe 50W, 80W, 125W, 250W and 400W DATA SHEET Product information Kolorlux Mercury vapor lamps
More informationBC-5000 OPERATIONS MANUAL BATTERY CAPACITY TESTER COFKO LLC.
BC-5000 BATTERY CAPACITY TESTER OPERATIONS MANUAL COFKO LLC. COPYRIGHT 2010 1 UNPACKING As you unpack your new BC-5000 battery capacity tester, inspect the tester for signs of shipping damage. If shipping
More informationINSTRUCTION MANUAL PLEASE READ ALL THE INSTRUCTIONS COMPLETELY BEFORE USE AND SAVE THIS MANUAL FOR FUTURE REFERENCE
INSTRUCTION MANUAL PLEASE READ ALL THE INSTRUCTIONS COMPLETELY BEFORE USE AND SAVE THIS MANUAL FOR FUTURE REFERENCE m Before Use Please read IMPORTANT SAFETY INSTRUCTIONS on page 10 before use. It is important
More informationAchat 115MA full-range speaker. user manual
Achat 115MA full-range speaker user manual Musikhaus Thomann Thomann GmbH Hans-Thomann-Straße 1 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 E-mail: info@thomann.de Internet: www.thomann.de
More informationREVIEWED BY CAPITAL PROJECTS MANAGER (DAN REDDY) GENERAL MANAGER EQUIPMENT ENGINEERING & ASSET MANAGEMENT (HAMILTON NXUMALO)
SA Port Operations DOCUMENT TYPE: REFERENCE EEAM-Q-014 (ORIGINAL SPECIFICATION HE8.2.3 Ver5) REVISION 0 SPECIFICATION TITLE: SPECIFICATION FOR ELECTRICAL MOTORS AND GENERATORS PAGE 0 of 07 COMPILED BY
More informationWARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY CAUTION: INSTALLATION LOCATION:
Revision Level: 01 Revision Date: 07/07/2011 Please read all instructions carefully to help ensure a correct and SAFE installation of your Second Wind Ultraviolet Germicidal Air Purifier. Failure to do
More informationOperating Instructions Bedienungsanleitung Mode d emploi
Operating Instructions Bedienungsanleitung Mode d emploi DW 400 www.bron-kobold.com Operating instructions DW 400 Before use Please read all the information contained in these operating instructions carefully.
More informationUser s Manual AURORA 1.2K/2.2K
User s Manual AURORA 1.2K/2.2K Uninterruptible Power System Safety CAUTION This UPS utilizes voltages that may be hazardous. Do not attempt to disassemble the unit. The unit contains no user serviceable
More informationNo. : EX##-OMF0004 OPERATION MANUAL. SI unit EX12#-SMB1
No. : EX##-OMF0004 OPERATION MANUAL EX12#-SMB1 Contents 1. Safety instructions ------------------------------------------------------ P3 2. Notes ------------------------------------------------------
More informationOperating Instructions Split System Air Conditioner
Operating Instructions Split System Air Conditioner Model No. Indoor Unit Type Indoor Unit Type Nominal Capacity 26 36 F2 Low Silhouette Ducted S-26PF2U6 S-36PF2U6 Connectable outdoor unit lineup This
More informationVACUUM CLEANER INSTRUCTION MANUAL
VACUUM CLEANER INSTRUCTION MANUAL MODEL: SVC9702 PLEASE READ THIS MANUAL CAREFULLY BEFORE USING AND KEEP IT PROPERLY FOR FUTURE USE 1 Safety Cautions: WARNING: To reduce the risk of fire, electrical shock,
More information1. Scope This specification is applied to ICR18650. 2. Product Specification Table 1 No. Item Rated Performance Remark
1. Scope This specification is applied to ICR18650. 2. Product Specification Table 1 No. Item Rated Performance Remark 1 Rated Capacity Typical Minimum 2 Nominal Voltage 3.7V 3 Voltage at end of Discharge
More informationCELO5. User & Installation Manual. www.audac.eu
CELO5 User & Installation Manual www.audac.eu 2 Introduction 5 High-end Slim Ceiling Speaker The CELO5 is the 5 version of AUDAC s CELO High-end Slim ceiling speaker series with an RMS power of 50 Watt
More informationPet hair clipper. Model 96822. Diagrams within this manual may not be drawn proportionally.
Pet hair clipper Model 96822 Cleaning And Operation Instructions Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the
More informationEPM3. Phase Sequence and Motor Rotation Tester. Users Manual
EPM3 Phase Sequence and Motor Rotation Tester Users Manual 1 L1 L2 L3 2 3 A B C CAT 600V 3-PHASE TESTER 5 TEST M1 M2 BATT M3 EPM3 MOTOR ROTATION TESTER EPM3 MOTOR ROTATION DETERMINED WHILE FACING MOTOR
More informationIMPORTANT INSTRUCTIONS & OPERATING MANUAL. Houston 50 Inch Electric Wall Mounted Fireplace Black / White
IMPORTANT INSTRUCTIONS & OPERATING MANUAL Houston 50 Inch Electric Wall Mounted Fireplace Black / White Model Number:MFE5050BK Model Number:MFE5050WH Read these instructions carefully before attempting
More informationSECTION 1: REQUIREMENTS FOR CERTIFICATES OF COMPLIANCE FOR CLASSES OF RADIATION APPARATUS
Department of Health and Human Services Population Health Radiation Protection Act 2005 Section 17 CERTIFICATE OF COMPLIANCE: STANDARD FOR RADIATION APPARATUS - X-RAY MEDICAL DIAGNOSTIC (MOBILE RADIOGRAPHY)
More informationCurrent valve. for AC 24 V pulse/pause control of electrical loads up to 30 kw
4 937 DESIO Current valve for AC 24 V pulse/pause control of electrical loads up to 30 kw SEA45.1 Use The current valve is used for the control of electric heating elements in heating, ventilation and
More informationSMD Rework Station TABLE OF CONTENTS
SMD Rework Station Thank you for purchasing the Hakko 50B SMD Rework Station. The Hakko 50B is designed to solder and desolder surface mounted devices with hot air. Please read this manual before operating
More informationDear Neuton Owner, This is a helpful hint to guide you in getting the most out of your NEUTON Battery and Charger.
Battery-Powered Mower NEUTON 24-Volt Charger Instructions Booklet Dear Neuton Owner, In order for you to get the most out of your Neuton Mower, we recently reviewed and revised our battery-charging instructions.
More informationEVERGREEN (C.P.) USA INC. TEL: (650) 952-8091 FAX: (650) 952-3629 E-MAIL: sales@evergreencpusa.com. SPECIFICATIONS Lithium Battery CR123A- 1700mAh
Voltage (V) Voltage (V) Voltage (V) EVERGREEN (C.P.) USA INC. SPECIFICATIONS Lithium Battery CR123A- 1700mAh Temperature characteristics(20ma) (mah) Pulse discharge characteristics Model CR123A Nominal
More informationPANCAKE CAPACITOR GENERATOR Installation, Operation and Maintenance Manual
PANCAKE CAPACITOR GENERATOR Installation, Operation and Maintenance Manual A Regal Brand TABLE OF CONTENTS INTRODUCTION 2 General Data 2 Initial Inspection 2 SAFETY 2 INSTALLATION 3 Location / Environment
More informationOPERATOR S MANUAL 18 VOLT, 1 HOUR CHARGER
OPERATOR S MANUAL 18 VOLT, 1 HOUR CHARGER P110 Your battery charger has been engineered and manufactured to Ryobi s high standard for dependability, ease of operation, and operator safety. When properly
More informationaseries A13B Mini Bullet Camera User Manual
aseries A13B Mini Bullet Camera User Manual Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the dealer. This manual applies to the MicroView
More informationPower supply unit Model: PAC-SC50KUA
Building Air Conditioning Control System Power supply unit Model: PAC-SC50KUA Installation Manual Contents 1. Safety precautions... 1 2. Product feature... 2 1. Specification... 2 2. Appearance... 2 3.
More informationSingle Phase Soft Starter
Single Phase Soft Starter Installation & Operating Manual 6/02 Table of Contents Section 1 General Information................................................... 1 1 General Description................................................
More informationSECTION 1: REQUIREMENTS FOR CERTIFICATES OF COMPLIANCE FOR CLASSES OF RADIATION APPARATUS
Department of Health and Human Services Population Health Radiation Protection Act 2005 Section 17 CERTIFICATE OF COMPLIANCE: STANDARD FOR RADIATION APPARATUS - X-RAY MEDICAL DIAGNOSTIC (BIOPSY) SECTION
More informationLi Battery Pack & Charger Safety & Operating Instructions
Li Battery Pack & Charger Safety & Operating Instructions NEUTON Power Equipment 75 Meigs Road Vergennes, VT 05491 Toll-Free phone: 1-866-NEUTON1 (638-8661) Fax: 1-802-877-1213 Website: www.neutonpower.com
More information804 Ti Stand. Manual 8.804.8001EN
804 Ti Stand Manual 8.804.8001EN Metrohm AG CH-9101 Herisau Switzerland Phone +41 71 353 85 85 Fax +41 71 353 89 01 info@metrohm.com www.metrohm.com 804 Ti Stand Manual 8.804.8001EN 06.2010 ek Teachware
More informationLithium Ion Battery Specifications
Lithium Ion Battery Specifications Type: Cylindrical Lithium Iron Phosphate Battery Mode: LFP-26650-3300 AA Portable Power Corp. Prepared by Checked by Approved by 1 . Product Specifications Type ------------
More informationV94 BULK TAPE DEGAUSSER
TECHNICAL MANUAL Operating and Maintenance Instructions for V94 BULK TAPE DEGAUSSER V94 BULK TAPE DEGAUSSER TECHNICAL MANUAL Document No. M000208 Production Standard ZZ 009 415 WARNING To help minimise
More informationNOTE: Additional user information for your printer may be available in the "Manuals" section at support.dell.com.
CAUTION: General Safety Instructions Use the following safety guidelines to help ensure your own personal safety and to help protect your equipment and working environment from potential damage. NOTE:
More informationli-ion Polymer Battery Specification
Customer: li-ion Polymer Battery Specification MODEL: GMB042035 Prepared By/Date Checked By/Date Approved By/Date Note:1.Kindly please sign on the above and send it back to us if the sample is approved.
More informationRexroth Hydraulic Pump A10VO Series User Manual
Rexroth Hydraulic Pump A10VO Series User Manual Rexroth Hydraulic pump A10VO Series User Manual Revised 5/1/2009 Page 1 of 12 Functional Purpose This pump is preferred over a fixed displacement (gear)
More informationSECTION 1: REQUIREMENTS FOR CERTIFICATES OF COMPLIANCE FOR CLASSES OF RADIATION APPARATUS
Department of Health and Human Services Population Health Radiation Protection Act 2005 Section 17 CERTIFICATE OF COMPLIANCE: STANDARD FOR RADIATION APPARATUS - X-RAY MEDICAL DIAGNOSTIC (MOBILE RADIOSCOPY)
More informationErgo-Pro Single Line Solar Station Installation and Operating Instructions
Rp 3/4 Ergo-Pro Single Line Solar Station Installation and Operating Instructions Item No Pump type 677.21.70 WILO ST 15/6 13 2 4 11 Technical Specifications Max. operating pressure: 6 bar Max. operating
More informationAntenna Splitter ASA 1. Instruction manual
Antenna Splitter ASA 1 Instruction manual Contents Important safety instructions... 2 The ASA 1 active antenna splitter... 4 Delivery includes... 4 Operating elements... 5 Putting the ASA 1 into operation...
More informationCAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN
BeoLab 7-6 Guide CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: To reduce the risk of electric shock, do not remove cover (or back). No User-serviceable parts inside. Refer servicing to qualified
More informationWine Cooler with Thermo-Electric Cooling & Heating Technology
Wine Cooler with Thermo-Electric Cooling & Heating Technology Model number: WC-0888H (8-bottles capacity) Instruction Manual Please read carefully and follow all safety rules and operating instructions.
More informationAchat 208 HL / 208 HR passive mid-range speaker. user manual
Achat 208 HL / 208 HR passive mid-range speaker user manual Musikhaus Thomann Thomann GmbH Hans-Thomann-Straße 1 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 E-mail: info@thomann.de Internet:
More informationMACBlower Model Number: MAC40R MAC60R MAC80R MAC100R. MAC120R MAC150R MAC 200R Serial # www.macblowers.com
MACBlower Model Number: MAC40R MAC60R MAC80R MAC100R MAC120R MAC150R MAC 200R Serial # Fuji Clean USA 41-2 Greenwood Road Brunswick, Maine 04011 207-406-2729 www.macblowers.com MACBlowers The Intelligent
More informationSeven function digital multimeter
Seven function digital multimeter 98025 Set up And Operating Instructions Distributed exclusively by Harbor Freight Tools. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com
More informationInstruction manual of pumps WQ, WQF, SN, Furiatka, Furia, KRAKEN, BIG, IP, IPE, SWQ, CTR
CAUTION! Instruction manual of pumps WQ, WQF, SN, Furiatka, Furia, KRAKEN, BIG, IP, IPE, SWQ, CTR NOTE: read the manual prior to commencement of use. For safety reasons, the pump can only be operated by
More informationARCO Electric Products Installation and Maintenance Manual Low Voltage Automatic Power Factor Correction Capacitor Systems 2013
ARCO Electric Products Installation and Maintenance Manual Low Voltage Automatic Power Factor Correction Capacitor Systems 2013 READ CAREFULLY These instructions are intended to cover good practices in
More informationAC-DC Converter Application Guidelines
AC-DC Converter Application Guidelines 1. Foreword The following guidelines should be carefully read prior to converter use. Improper use may result in the risk of electric shock, damaging the converter,
More informationPressure monitoring equipment for oil-sf 6. bushings, type GOEK
Pressure monitoring equipment for oil-sf 6 bushings, type GOEK Installation and maintenance guide 5693 827-6 en, Rev. 3, 2002-01-30 This document must not be copied without our written permission, and
More informationGF SERIES 1-TANK/2-TANK ELECTRIC FRYER USER S MANUAL
GF SERIES 1-TANK/2-TANK ELECTRIC FRYER USER S MANUAL Thank you for purchasing and using GF series Electric Fryer. In order to make full use of functions of this product and minimize unnecessary loss and
More informationSingle-Phase AC Synchronous Generator
ST Series Single-Phase AC Synchronous Generator Instructions for Operation and Maintenance English to English translation by R.G. Keen, May 2004. ST Series of Single-Phase AC Synchronous Generators Description
More informationUSER INSTRUCTIONS FOR 10 LITRE PORTABLE DEHUMIDIFIER MODEL NO. DHMD102
USER INSTRUCTIONS FOR 10 LITRE PORTABLE DEHUMIDIFIER MODEL NO. DHMD102 THANK YOU FOR CHOOSING YOUR NEW DEHUMIDIFIER. BEFORE USING THE UNIT READ THESE INSTRUCTIONS FULLY AND RETAIN THEM FOR FUTURE REFERENCE
More informationMounting Instructions. Torque Transducer. A0329 3.2 en
Mounting Instructions Torque Transducer T5 T5 Contents 3 Page Safety instructions.............................................. 4 1 Measuring characteristics..................................... 7 2 Mounting.....................................................
More informationCisco TelePresence MCU 4500 Series safety and compliance information
Cisco TelePresence MCU 4500 Series safety and compliance information On this page: Safety information symbols Operating guidelines Safety warnings Technical specifications Compliance information WEEE information
More informationPump Specifications 250 Series Submersible Sump / Effluent Pump 2 Solids handling
Pump Specifications 250 Series Submersible Sump / Effluent Pump 2 Solids handling 250_P1 R10/7/2015 Copyright 2015 Liberty Pumps Inc. All rights reserved. Specifications subject to change without notice.
More informationWood pellet and biomass system ceramic igniter
Wood pellet and biomass system ceramic igniter Specification Data Product name: Ceramic Igniter PSx-2-120-W Drawing number: IBA-HH020A Revised on: 2015.12.20 1. Application This engineering specification
More informationType: EASY719 DC RC Article No.: 274119. Ordering information Relay outputs Quantity 6 Power supply V DC 24 V DC. Description
Type: EASY719 DC RC Article.: 274119 Ordering information Relay outputs Quantity 6 Power supply V DC 24 V DC Description 12 digital inputs (4 inputs available as analog inputs) 6 relay outputs LCD display
More informationUT202A Operating Manual. Contents
Title Contents Page Overview Unpacking Inspection Safety Information Rules for Safe Operation International Electrical Symbols The Meter Structure Functional Buttons and auto power off Display Symbols
More informationSERVICE MANUAL OUTDOOR UNIT. No. OBH590 REVISED EDITION-B. Models HFC
SPLIT-TYPE AIR CONDITIONERS Revision B: MUZ-EF25/35/42/50VE - E2 and MUZ-EF25/35VEH - E2 have been added. Please void OBH590 REVISED EDITION-A. OUTDOOR UNIT SERVICE MANUAL HFC utilized R410A. OBH590 REVISED
More informationINSTALLATION INSTRUCTIONS Fan Coil Replacement Coil Kit EBX & EBXX
Fan Coil Replacement Coil Kit EBX & EBXX These instructions must be read and understood completely before attempting installation. These instructions covers the installation of replacement coil kit into
More information19 LED Tube Controller ORDERCODE 41003
19 LED Tube Controller ORDERCODE 41003 Congratulations! You have bought a great, innovative product from Showtec. The Showtec 19 LED Tube Controller brings excitement to any venue. Whether you want simple
More informationSpecification of 5 Wire Analog Touch Panel
Specification of 5 Wire Analog Touch Panel 5 WIRE ANALOG RESISTIVE TOUCH PANEL A. Application This specification applies to the 5 Wire Analog Resistive Touch Panel. B. Environmental Conditions 1. Operating
More informationLS1024B / LS2024B/ LS3024B. Solar Charge Controller USER MANUAL
EPSOLAR LS1024B / LS2024B/ LS3024B Solar Charge Controller USER MANUAL Thank you very much for selecting our product! This manual offers important information and suggestions with respect to installation,
More informationOPERATING MANUAL. Table of contents. 2 Phase Stepping Motor Driver 2M542. Rev. A. Introduction page 2. Specifications page 2 Timing chart page 3
2 Phase Stepping Motor Driver 2M542 OPEATING MANUAL Table of contents Introduction page 2 Specifications page 2 Timing chart page 3 Setting page 4 Current set page 4 educe current function page 4 Micro
More information