TECHNICAL. SLP-4 Single Line Paging Controller with CD Quality Westminster Chimes

Transcription

1 TECHNICAL Practice TELE SOLUTIS FOR THE 21ST CENTURY SLP-4 Single Line Paging Controller with CD Quality Westminster Chimes November 18, 2010 Features Phone Add Whole-House Paging, Loud Ringing, Phone-to- Phone Intercom and CD Quality Westminster Door Chimes to Your Multi-Room Audio System The SLP-4 Single Line Paging controller will allow you to page family members or co-workers from any phone in your home or small office. The pages can be heard over the same speakers that are installed for multi-zone music distribution. The SLP-4 provides inputs for 4 lighted doorbell switches. The inputs select 4 different CD quality sounds from a library of eight factory recordings including Westminster bells, chimes, alert tones, barking dogs, etc. Alternatively, users may record their own CD quality sounds into the SLP-4 from their PC s port. When the doorbell switch is pressed, background music is muted while the appropriate sound is heard over the system speakers. The SLP-4 connects in series with a single existing phone line. The unit has a built-in 2 watt amplifier, pre-amp output, music on hold input, intercom features, and selectable loud ringing. Factory loaded CD quality Westminster door chimes Stereo line level pre-amp inputs/outputs for whole house audio systems Built-in two-watt mono paging amplifier with gain control Phone to phone intercom Place callers on music-on-hold when paging Can provide background music from an external source Background music mute (automatic during paging or touch tone selectable while you are on a call) Selectable loud ringing (electronic warble over speakers) Four doorbell switch inputs (lighted or non-lighted) for activating door chimes Other door sounds: ding-dong, knocking, tones, barking port for loading custom WAV file chime tones/ sounds/music 6 minutes of recorded audio storage Switch selectable on-hold alarm tones Page trigger output (12V signal for enabling paging source input on multi-source amps) Individual Chime, Page, and Ringing volume controls Bypass code - ignores all touch tones on next off-hook allowing you to steer through auto attendants, etc. Page from multiple phone lines by connecting multiple units Comes complete with power supply Applications Whole house/small business paging from existing phones Add paging, intercom, and music on hold features for small businesses Loud ringing / night bell Compatible with C-200, C-250, C-1000B and C-2000B Museum or Info Center, 4 button audio server Specifications Power: 120V AC/13.8V AC 1.25A, UL listed adapter provided Dimensions: 210mm x 159mm x 45mm (8.25 x 6.25 x 1.75 ) Shipping Weight: 1.5 kg (3.2 lbs) Environmental: 0 C to 32 C (32 F to 90 F) with 5% to 95% non-condensing humidity Paging Amplifier Output: 2 watts - powers up to (3) 8 ohm (16) 45 ohm speakers Sound Pressure: meter (loud electronic warble from 25AE paging horn) REN: 0.5A Maximum Speaker Output Wire Run: 91m (300 ft), 18 AWG Maximum Doorbell Switch Wire Run: 305m (1000 ft), 24 AWG Maximum Load on Page Trigger Output: 1K Ohm Talk Battery: 36V DC WAV File Resolution: 16 bit or 8 bit WAV File Sampling Rate: 44.1K, 22K, or 11K Connections: 24 screw terminal block positions, (4) RCA jacks, (1) Type B jack, (1) 3.5mm (1/8 ) audio jack

2 IF YOU HAVE A PROBLEM WITH A PRODUCT, PLEASE CTACT: TECHNICAL SUPPORT AT (715) Our Technical Support Department is available for assistance Monday 8am - 4pm and Tuesday through Friday 8am - 5pm central time. So that we can give you better service, before you call please: 1. Know the model number, the serial number and what software version you have (see serial label). 2. Have your Technical Practice in front of you. 3. It is best if you are on site. RETURNING PRODUCT FOR REPAIR The following procedure is for equipment that needs repair: 1. Customer must contact Viking's Technical Support Department at to obtain a Return Authorization (RA) number. The customer MUST have a complete description of the problem, with all pertinent information regarding the defect, such as options set, conditions, symptoms, methods to duplicate problem, frequency of failure, etc. 2. Packing: Return equipment in original box or in proper packing so that damage will not occur while in transit. Static sensitive equipment such as a circuit board should be in an anti-static bag, sandwiched between foam and individually boxed. All equipment should be wrapped to avoid packing material lodging in or sticking to the equipment. Include ALL parts of the equipment. C.O.D. or freight collect shipments cannot be accepted. Ship cartons prepaid to: Viking Electronics, 1531 Industrial Street, Hudson, WI Return shipping address: Be sure to include your return shipping address inside the box. We cannot ship to a PO Box. 4. RA number on carton: In large printing, write the R.A. number on the outside of each carton being returned. Features Overview RETURNING PRODUCT FOR EXCHANGE The following procedure is for equipment that has failed out-of-box (within 10 days of purchase): 1. Customer must contact Viking s Technical Support at to determine possible causes for the problem. The customer MUST be able to step through recommended tests for diagnosis. 2. If the Technical Support Product Specialist determines that the equipment is defective based on the customer's input and troubleshooting, a Return Authorization (R.A.) number will be issued. This number is valid for fourteen (14) calendar days from the date of issue. 3. After obtaining the R.A. number, return the approved equipment to your distributor, referencing the R.A. number. Your distributor will then replace the product over the counter at no charge. The distributor will then return the product to Viking using the same R.A. number. 4. The distributor will NOT exchange this product without first obtaining the R.A. number from you. If you haven't followed the steps listed in 1, 2 and 3, be aware that you will have to pay a restocking charge. LIMITED WARRANTY Viking warrants its products to be free from defects in the workmanship or materials, under normal use and service, for a period of one year from the date of purchase from any authorized Viking distributor or 18 months from the date manufactured, which ever is greater. If at any time during the warranty period, the product is deemed defective or malfunctions, return the product to Viking Electronics, Inc., 1531 Industrial Street, Hudson, WI., Customer must contact Viking's Technical Support Department at to obtain a Return Authorization (R.A.) number. This warranty does not cover any damage to the product due to lightning, over voltage, under voltage, accident, misuse, abuse, negligence or any damage caused by use of the product by the purchaser or others. NO OTHER WARRANTIES. MAKES NO WARRANTIES RELATING TO ITS PRODUCTS OTHER THAN AS DESCRIBED ABOVE AND DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTIES OR MERCHANTABILITY OR FITNESS FOR ANY PAR- TICULAR PURPOSE. EXCLUSI OF CSEQUENTIAL DAMAGES. SHALL NOT, UNDER ANY CIRCUMSTANCES, BE LIABLE TO PURCHASER, OR ANY OTHER PARTY, FOR CSEQUENTIAL, INCIDENTAL, SPECIAL OR EXEMPLARY DAMAGES ARISING OUT OF OR RELATED TO THE SALE OR USE OF THE PRODUCT SOLD HEREUNDER. EXCLUSIVE REMEDY AND LIMITATI OF LIABILITY. WHETHER IN AN ACTI BASED CTRACT, TORT (INCLUDING NEGLIGENCE OR STRICT LIABILITY) OR ANY OTHER LEGAL THEORY, ANY LIABILITY OF SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE PRODUCT, OR AT 'S OPTI, REFUND OF THE PURCHASE PRICE AS THE EXCLUSIVE REMEDY AND ANY LIABILITY OF SHALL BE SO LIMITED. IT IS EXPRESSLY UNDERSTOOD AND AGREED THAT EACH AND EVERY PROVISI OF THIS AGREEMENT WHICH PROVIDES FOR DISCLAIMER OF WARRANTIES, EXCLUSI OF CSEQUENTIAL DAMAGES, AND EXCLUSIVE REMEDY AND LIMITATI OF LIABILITY, ARE SEVERABLE FROM ANY OTHER PROVISI AND EACH PROVISI IS A SEPARABLE AND INDEPENDENT ELEMENT OF RISK ALLOCATI AND IS INTENDED TO BE ENFORCED AS SUCH. FCC REQUIREMENTS This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the side of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company. The REN is used to determine the number of devices that may be connected to a telephone line. Excessive REN's on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of the REN's should not exceed five (5.0) To be certain of the number of devices that may be connected to a line, as determined by the total REN's, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label. The plug used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this SLP-4 does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. If the SLP-4 causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make the necessary modifications to maintain uninterrupted service. ELECTRICS HUDS, WI If trouble is experienced with the SLP-4, for repair or warranty information, please contact: Viking Electronics, Inc., 1531 Industrial Street, Hudson, WI (715) If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. Connection to Party Line Service is subject to State Tariffs. Contact the state public utility commission, public service commission or corporation commission for information. WHEN PROGRAMMING EMERGENCY NUMBERS AND (OR) MAKING TEST CALLS TO EMERGENCY NUMBERS: Remain on the line and briefly explain to the dispatcher the reason for the call. Perform such activities in the off-peak hours, such as early morning or late evenings. It is recommended that the customer install an AC surge arrester in the AC outlet to which this device is connected. This is to avoid damaging the equipment caused by local lightning strikes and other electrical surges. PART 15 LIMITATIS This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. PLAYBACK Status LEDs DIP Switches (see page 8) SINGLE LINE PAGING CTROLLER CHIMES / MESSAGES ING Volume Controls - For paging, amp gain, loud ringing, and triggered chime tones. - Type B jack for downloading custom wave files. Music on Hold Input (mono, 1/8" / 3.5mm) Line level input from radio, etc. MUSIC CHIME/MESSAGE SELECTIS HOLD ALARM FILE 4 MUTE AUDIO MUTE AUDIO TRIGGER Page Trigger Output - Connect to multizone amplifiers requiring a switched signal for enabling the paging source input. Dry Page Trigger - Secondary dry relay output contacts. Optional Earth Ground C.O. / Phone Line Input Line Out to Phones Doorbell Switch Inputs (lighted or non-lighted) - Provides door chime over speakers (not polarity sensitive). Input can also be connected to a Viking model C-1000B or C-2000A for unique front / back door chimes. GND PHES TRIG 1 TRIG 2 TRIG 3 TRIG 4 - IO SPK - Left and Right Audio Loop Output (stereo, RCA-type) Line level output to external amplifier. Left and Right Audio Loop Input (stereo, RCA-type) Line level pre-amp input for background music, etc. Speaker Output (2 watt maximum, connect up to three 8-ohm speakers in parallel) 2 Loud Ring Enable Input (shorted: enabled, open: disabled) Provides warble over speakers during phone line ringing. I.O. Communications - Connect to multiple units for multiline applications with one amplifier (polarity sensitive).

3 Installation A. Music On Hold A music source, such as a radio, can be connected to the SLP-4 s MOH input jack using the provided audio cord. This will provide any caller that has been put on hold with music, to reassure callers they have remained connected while waiting. Adjust the MOH level with the volume control on the music source. 13.8V AC Adapter 120V AC 1/8" (3.5mm) Double Ended Audio Cord MUSIC GND ELECTRICS HUDS, WI SINGLE LINE PAGING CTROLLER CHIMES / MESSAGES CHIME/MESSAGE SELECTIS HOLD ALARM FILE 4 MUTE AUDIO PHES TRIG 1 TRIG 2 TRIG 3 TRIG 4 - IO SPK - MUTE AUDIO PLAYBACK TRIGGER ING Music On Hold Source (Radio) B. Telecom Wiring Adjust Music On Hold Volume The SLP-4 should be wired ahead of all phones so that every phone can use the SLP-4 Telcom features (Page, Hold, Intercom, etc.). Connect the phones to the two screw terminals labeled PHES. The incoming analog phone service (C.O. line, VoIP analog port, etc.) is to be connected to the screw terminals labeled. To increase surge protection, wire the EARTH GND screw terminal to a water pipe, or grounding rod. To enable the SLP-4 to provide a loud ringing warble sound over the speakers when a call is ringing in, strap together screw terminals labeled ENABLE. Paging volume and Loud Ringing volume levels can be independently adjusted using a small screwdriver to adjust the trim POTs on the right side of the SLP V AC Adapter 120V AC ELECTRICS HUDS, WI SINGLE LINE PAGING CTROLLER CHIMES / MESSAGES PLAYBACK ING Adjust Page Volume Adjust Loud Ringing Volume *Earth Ground MUSIC GND CHIME/MESSAGE SELECTIS HOLD ALARM FILE 4 MUTE AUDIO PHES TRIG 1 TRIG 2 TRIG 3 TRIG 4 - IO SPK - MUTE AUDIO TRIGGER C.O. / Phone Line Optional Methods for Enabling Loud Ringing Shorted Time Controlled Relay "Night" Switch (SPST) To Additional Analog Phones Analog Phone - or - - or - 3

4 C. Doorbell / Triggered Audio Connections The SLP-4 will accommodate up to 4 doorbell inputs. A lighted or non-lighted doorbell button, or any other normally open switch that provides a momentary closure, can trigger the SLP-4 to play a door chime recording. The SLP-4 is factory loaded with 8 different non-compressed true CD quality chimes / sounds (see DIP Switch Programming, page 8). Each of the 4 triggered inputs can be selected to playback any one of the 8 recordings using the associated DIP Switches. Alternatively, users may load their own CD quality recordings into the SLP-4 from their PC via the connection (see Downloading WAV Files, page 9). The recorded Chimes / Sounds volume level can be adjusted using a small screwdriver to adjust the trim POT on the right side of the SLP-4. Since 6 minutes of high quality audio may be custom recorded, the SLP-4 can be used as a 4 button information on-demand announcer at a museum or information booth point of interest location. Because the SLP-4 includes a built in 2 watt amplifier, no other electronics besides the momentary push buttons, and speaker(s) are needed. 13.8V AC Adapter 120V AC Doorbell Switch 1 MUSIC GND ELECTRICS HUDS, WI SINGLE LINE PAGING CTROLLER CHIMES / MESSAGES CHIME/MESSAGE SELECTIS HOLD ALARM FILE 4 MUTE AUDIO PHES TRIG 1 TRIG 2 TRIG 3 TRIG 4 - IO SPK - MUTE AUDIO PLAYBACK TRIGGER Doorbell Switch 4 ING Adjust Chime Volume Doorbell Switch 2 Doorbell Switch 3 Driveway Detector can trigger "Alert Tone" -OR- -OR- Yard Motion Detector can trigger "Barking Dog" D. Amplified Speaker Output For convenience, the SLP-4 supplies a 2 watt amplified output that can be useful in a couple of different ways: 1. If the installation does not have an existing paging or audio system and only a few speakers are needed, the SLP-4 will also serve as the power amplifier to directly drive up to three 8 ohm speakers. 2. If the installation uses a whole house audio system in which all zones are turned off at night, the SLP-4 s speaker output can be used to drive a few speakers in central locations (i.e. front hallway), so the SLP-4 features such as the Doorbell Chimes can still be heard. 13.8V AC Adapter 120V AC MUSIC GND ELECTRICS HUDS, WI SINGLE LINE PAGING CTROLLER CHIMES / MESSAGES CHIME/MESSAGE SELECTIS HOLD ALARM FILE 4 MUTE AUDIO PHES TRIG 1 TRIG 2 TRIG 3 TRIG 4 - IO Up to (3) 8 Ohm Speakers SPK - MUTE AUDIO PLAYBACK TRIGGER ING Model 25AE Paging Horn shown (not included) Model 30AE Ceiling Speaker shown (not included) 4

5 E. Audio Connections How the SLP-4 audio connections are wired, is dependent on the system it is being installed into. Shown below are two possible examples. 1. Wiring to a Multi-Zone Whole House Audio System Typical of multi-zone whole house audio systems, a single RCA audio jack is used for its page input. Most multi-zone controllers/amplifiers require a 12 Volt DC trigger signal (or relay contact closure), to automatically switch the source to the page input. The SLP-4 will provide a switched signal (or dry relay contact closure), which is maintained while the unit is paging or for the duration of the door chime recording. It is crucial that correct polarity for the 12 volt DC trigger be observed. If the 12 Volt DC trigger is wired reverse polarity, it will not function properly, and the multi-zone audio system will instead trigger on audio detection. When this is the case, the first part of the page or door chime recording is not heard. 13.8V AC Adapter 120V AC Warning: Multi-zone controllers without a page trigger input (audio sensing only) are not recommended, as the 1st word during paging is usually omitted. MUSIC GND ELECTRICS HUDS, WI SINGLE LINE PAGING CTROLLER CHIMES / MESSAGES CHIME/MESSAGE SELECTIS HOLD ALARM FILE 4 MUTE AUDIO PHES TRIG 1 TRIG 2 TRIG 3 TRIG 4 12V DC Page Trigger (Control) Input Page Input Multi-Zone Audio System - - IO SPK - MUTE AUDIO PLAYBACK TRIGGER ING TIP: If the first part of a door chime recording is not heard, and it has been determined the 12V DC page trigger is wired with proper polarity, then the whole house audio system must need additional delay time before it is ready to pass audio. This can be corrected by programming a Trigger Delay time in the SLP-4. The Trigger Delay time is a selection in the SLP-4 Message Manager application, which is typically used to load custom WAV audio files from a PC via a cable (see page 9). The delay can be programmed from 1 to 9 seconds, and is from when the SLP- 4 provides the page trigger signal, until the recording starts to play. 2. Wiring to a Stereo Receiver Audio System The SLP-4 has two audio inputs (L & R) and two audio outputs (L & R) available on RCA jacks. When the SLP-4 is in its idle state, the audio is simply looped thru the unit. Because of this, the SLP-4 can be inserted between an audio system s pre-amp and power amplifier, or wired into a Tape Monitor loop of a stereo receiver (as shown). The Tape Monitor loop on the stereo receiver must be turned on. Background music coming into the SLP-4 s audio input jacks will be muted during page and doorbell chimes. 13.8V AC Adapter 120V AC MUSIC ELECTRICS HUDS, WI SINGLE LINE PAGING CTROLLER CHIMES / MESSAGES CHIME/MESSAGE SELECTIS HOLD ALARM FILE 4 MUTE AUDIO MUTE AUDIO PLAYBACK TRIGGER ING GND PHES TRIG 1 TRIG 2 TRIG 3 TRIG 4 - SPK - IO L R L R Pre-Out or Tape Out Main In or Tape In Stereo Receiver 5

6 TRIG. OUT GND PHES TRIG 1 TRIG 2 TRIG 3 TRIG 4 - IO SPK - on GND PHES TRIG 1 TRIG 2 TRIG 3 TRIG 4 - IO SPK - F. Multi-Line Paging (I.O. ) The SLP-4 is designed to operate on a single phone line. If paging is required on two or more phone lines, connect one SLP-4 or SLP-1 per line. Multiple SLP-4 s or SLP-1 s can be connected to the same Pre-Amp, Amp or Receiver. When using multiple units, it is important to follow these guidelines: 1. One SLP per line with a maximum of ten lines/units. 2. The I.O. connections must all be connected together and in proper polarity. 3. Cascade the audio connections from the first unit to the last unit. 4. Background music would need to come into the first unit. 5. Audio outputs from the last unit into the audio system. 6. If used, the trigger outputs ( or ) must all be connected together and in proper polarity. 7. Units wired closer to the amplifier will take higher priority when creating loud ringing, doorbell chimes, etc. 8. Paging will be allowed on a first come, first serve basis. Any person attempting to page on another SLP will hear a busy signal on their phone. ELECTRICS HUDS, WI PLAYBACK ELECTRICS HUDS, WI PLAYBACK PWR MODEL SLP-1 PREAMP ELECTRICS HUDS, WI MIN MAX MIN MAX SINGLE LINE PAGING CTROLLER SINGLE LINE PAGING CTROLLER CHIMES / MESSAGES ING SINGLE LINE PAGING CTROLLER CHIMES / MESSAGES ING MUSIC HOLD AUDIO L R AUDIO L R CHIME/MESSAGE SELECTIS HOLD ALARM MUSIC FILE 4 MUTE AUDIO TRIGGER CHIME/MESSAGE SELECTIS HOLD ALARM MUSIC FILE 4 MUTE AUDIO TRIGGER DOOR BELL - SW. ENABLE I.O.. - PWR MUTE MUTE AUDIO MUTE AUDIO C.O. LINE PHES - SPKR L R L Audio In R Cascade Audio I.O. Connections Application Wiring ELECTRICS HUDS, WI SINGLE LINE PAGING CTROLLER CHIMES / MESSAGES - - Cascade Audio PWR I.O. Connections ELECTRICS HUDS, WI MODEL C-2000B ADVANCED DOOR/GATE AND ENTRY PHE CTROLLER Audio Out To Additional SLP-4 units A. Provide Paging* with Unique Front and Back Door Chimes and Control of up to Four Entry Phones and Doorstrikes from a Single Phone Line with the Viking C-2000B The SLP-4 can be used with the Viking C-2000B entry phone controller. The phone line first runs through the SLP-4, then runs through the C-2000B before continuing on to the house phones. The C-2000B s normally open Aux Contact Output connections, when wired to the SLP-4 s Trig1 input, will play the SLP-4 s chimes whenever an entry phone calls in. Regardless of the Triggered Audio DIP switch settings; Entry Phone 1 will play Message 1 (factory loaded with Westminster 4 chime), Entry Phone 2 will play Message 2 (Ding Dong). Entry Phone 3 will play Message 3 (Triangle 2) and Entry Phone 4 will play Message 4 (Goblet Chime). To provide these unique front and back door chimes, the SLP-4 s Doorbell Mode dip switch must be turned, and the C-2000B must have the Auxiliary Contact Mode enabled (DIP switch 1 ) and have the auxiliary contact programmed for Entry Phone Triggered Ring Cadence Activation (3#60). Entry phone ringing can also be disabled (0#62). See the C-2000B Technical Practice for programming details (DOD# 156). * Note: The SLP-4 paging features are not compatible with the C-2000B in the Analog Station Dial Through mode. PLAYBACK ING MUSIC CHIME/MESSAGE SELECTIS HOLD ALARM FILE 4 MUTE AUDIO MUTE AUDIO TRIGGER EARTH GND PHE LINE LINE OUT TO PHES ANALOG STATI ENTRY PHE 1 DOOR STRIKE 1 J7- ENTRY PHE 2 DOOR STRIKE 2 J9- J8- ENTRY PHE 3 DOOR STRIKE 3 J10- ENTRY PHE 4 DOOR STRIKE 4 J11- DOORBELL SWITCH / AUX. AUX. CTACT 4 5 LED1 LED2 LED3 C LED4 C LED5 C LED6 C LED7 C C C C.O. / Phone Line GND PHES TRIG 1 TRIG 2 TRIG 3 TRIG 4 - SPK - IO *To Entry Phones To Additional Analog Phones 6 DIP Switch 1 must be 4 5 DIP Switch 1 & 5 must be Analog Phone * IMPORTANT: See the C-2000B Technical Practice for complete wiring instructions (DOD# 156).

7 B. Provide Paging, Music-On-Hold and Single Entry Phone Control with the Viking C-200 The SLP-4 can be used with the Viking C-200 single entry phone controller. The phone line first runs through the SLP-4, then runs through the C-200 before continuing on to the house phones. The C-200 normally open Aux Contact Output connections, when wired to the SLP-4 s Trig1 input, will play the SLP-4 s Message 1 (Westminster 4 chime) whenever the Entry Phone calls in. To enable this function, the SLP-4 s Doorbell Mode dip switch must be turned, and the C-200 must have the relay set to activate a doorbell (DIP switch 2 ). PLAYBACK ELECTRICS HUDS, WI * IMPORTANT: See the C-200 Technical Practice for complete wiring instructions (DOD# 169). SINGLE LINE PAGING CTROLLER CHIMES / MESSAGES ING MODEL C-200 ELECTRICS HUDS, WI MUSIC CHIME/MESSAGE SELECTIS HOLD ALARM FILE 4 MUTE AUDIO TRIGGER PWR COUNT RELAY MODE SINGLE ENTRY PHE CTROLLER EARTH GND PHE LINE LINE OUT TO PHES TO ENTRY PHE AUX RELAY CTACTS AUX MUTE AUDIO C.O. / Phone Line GND PHES TRIG 1 TRIG 2 TRIG 3 TRIG 4 - SPK - IO EARTH C.O. LINE ENTRY AUX GND PHES PHE AUX CTACTS *To Entry Phone To Additional Analog Phones DIP Switch 1 must be DIP Switch 2 must be Analog Phone C. Provide Paging, Doorbox and Doorstrike Control with Unique Front and Back Door Chimes with Viking Doorboxes and the C-1000B The SLP-4 can be used with the Viking C-1000B entry phone controller. The phone line first runs through the SLP-4, then runs through the C-1000B before continuing on to the house phones. The C-1000B s normally open Aux Contact Output connections, when wired to the SLP-4 s Trig1 input, will play the SLP-4 s chimes whenever a Doorbox calls in. Regardless of the Triggered Audio DIP switch settings; Doorbox 1 will play Message 1 (factory loaded with Westminster 4 chime), and Doorbox 2 will play Message 2 (factory loaded with Ding Dong chime). To provide these unique front and back door chimes from the SLP-4, the C-1000B must be programmed to enable the Auxiliary Contact Mode ( 7) and have the auxiliary contact programmed for custom ring cadence (12#03). Doorbox ringing can also be disabled by placing the C-1000B in the Doorbell Mode ( 1). See the C-1000B Technical Practice for programming details. The C-1000B CCTV Video Control Mode can NOT be used in conjunction with unique front and back door chimes. See Operation section I, page 7. The caller s music on hold is limited to 5 seconds while communicating with a doorbox. ELECTRICS HUDS, WI SINGLE LINE PAGING CTROLLER CHIMES / MESSAGES PLAYBACK ING * IMPORTANT: See the C-1000B Technical Practice for complete wiring instructions (DOD# 168). ELECTRICS HUDS, WI MODEL C-1000B MUSIC CHIME/MESSAGE SELECTIS HOLD ALARM FILE 4 MUTE AUDIO MUTE AUDIO TRIGGER PWR EARTH GND PHE LINE DOOR ENTRY / CCTV VIDEO / PAGING CTROLLER LINE OUT TO PHES KEYLESS CTACT CLOSURE DOORBOX 1 DOORBOX PWR DOORBOX 2 DOOR STRIKE 1 DOOR STRIKE 2 GND PHES TRIG 1 TRIG 2 TRIG 3 TRIG 4 - SPK - IO AUX. CTACT C.O. / Phone Line SIG GND SIG GND SIG GND VIDEO 1 IN VIDEO 2 IN VIDEO OUT C LED1 TALK BATTERY C LED2 C LED3 EARTH C.O. LINE KEYLESS DOOR DOORBOX DOOR GND PHES C.C. BOX 1 13VAC PWR BOX 2 DOOR STRIKE 1 DOOR STRIKE 2 To Additional Analog Phones * To Doorboxes DIP Switch 1 must be Analog Phone 7

8 D. Eliminating Paging Feedback Squeal Paging feedback squeal can occur when phones are used in close proximity to the paging speakers. To eliminated paging feedback, turn down the paging volume, move the phones away from the speakers or install a Viking model FBI-1A Digital Anti- Feedback Paging Interface. For more information on the FBI-1A, see DOD# 465. Programming A. DIP Switch Programming 1. Mode DIP Switches Switch Position Description Trigger 1 input connected to a typical doorbell switch (factory default) Trigger 1 input connected to a C-200, C-1000B or C-2000B auxiliary contact output On-hold alarm disabled On-hold alarm tone enabled, a double beep each minute a call is on hold (factory default) Instant outside line access (factory default) Dial 9 to access an outside line Mode DIP Switches PLAYBACK ELECTRICS HUDS, WI SINGLE LINE PAGING CTROLLER CHIMES / MESSAGES ING Note: DIP switches are shown in factory default settings. MUSIC CHIME/MESSAGE SELECTIS HOLD ALARM FILE 4 MUTE AUDIO MUTE AUDIO TRIGGER GND PHES TRIG 1 TRIG 2 TRIG 3 TRIG 4 - SPK - IO 2. Triggered Audio DIP Switches The SLP-4 will accommodate up to 4 doorbells wired to its 4 triggered audio inputs (see page 4). Each triggered audio input can play any one of 8 factory loaded CD quality chime/messages. Alternatively, users may download their own CD quality WAV file from a computer via the jack to customize their installation (see Downloaded WAV Files, page 9). A set of 3 DIP switches for each associated triggered input are used to independently select which of the 8 chime/messages are to be played for each trigger. Below are the factory loaded chime/messages DIP switch assignments. Note: DIP switches are shown in factory default settings. Triggered Audio DIP Switches TRIG 1 TRIG 2 TRIG 3 TRIG 4 Message Switch 1 Switch 2 Switch 3 Description Westminster 4 (TRIG 1 default) Ding Dong (TRIG 2 default) Triangle 2 (TRIG 3 default) Goblet Chime (TRIG 4 default) Wind Chime Notes Door Knock Alert Tone 2 Dogs Barking 8

9 B. Downloading WAV Files (optional) The SLP-4 comes factory loaded with 8 CD quality chime/messages. These chime/messages work well for differentiating between up to four different doors when wired to doorbell buttons. The default DIP switch settings have the SLP- 4 playing the Westminster 4, Ding Dong, Triangle 2, and Goblet Chimes, as shown on page 8. Users may choose to select any of the other factory loaded chime/messages (Wind Chime Notes, Door Knock, Alert Tone 2 or Dogs Barking), which best fits their household style. For a truly custom sounding doorbell chime/message, users may download their own WAV files into the SLP-4 from a computer via the connection. Recording up to 8 different theme or seasonal recordings such as team fight songs, jingle bells, Halloween sounds, Brahm s Lullaby, Harley rev, electric guitar riff, etc., all become possible. Go to select Software Downloads, and then choose SLP-4 Message Manager to proceed. WAV File Guidelines: 1. For best results, the WAV file should be 16 bit / 44.1K / mono. 2. Resolution down to 8 bits is acceptable but audio quality will not be optimal. 3. Sampling rates of 22k and 11k are also acceptable. 4. The WAV file may be stereo or multi-channel, but only the Left Channel will be loaded. 5. Each of the 8 Memory Locations can hold up to 44 seconds of recorded audio (at 11k sample rate). 6. Total recording time of 5 minutes 52 seconds available (at 11k sample rate). 7. Longer recordings are allowed to spill over into additional memory locations. Note: Audio CDs use Red Book audio. The commonality is that both audio CDs and WAV files have the audio data encoded in PCM. The Audio Red Book standard is essentially a WAV file along with additional coded information such as title, track, and time information. Applications such as Sound Forge, Audacity, and Windows Sound Recorder can be used to generate WAV files out of Audio CD and/or MP3 audio recordings. When using the SLP-4 Message Manager software, there is the option to select either the Stack or Interrupt Chime/Message Mode. The SLP-4 is factory set in the Stack mode which means if the front doorbell button and the back doorbell button are pressed at about the same time, the SLP-4 will fully play the first chime/message, and then fully play the second chime/message. The Interrupt mode works well if the SLP-4 is being used as a museum or information display 4 button audio server (see page 4). This works well for this application because each new push of the button will instantly start playing the recording the user requested. A delay time can be programmed from when the SLP-4 provides the page trigger signal, until the door chime recording starts to play. This is useful if the whole house audio system needs additional delay time before it is ready to pass audio. In the SLP-4 Message Manager software Options box, a Trigger Delay time from 0 to 9 seconds may be selected. Note: For proper operation, unplug the cord from the SLP-4 when finished loaded the WAV files. Operation A. Paging To page throughout the house/small business, simply press #, then 7 (the letter P key on your keypad). Speak into the phone receiver and your voice will be heard throughout the house or small business over the speakers. If background music is present over the speakers, it will automatically mute allowing your page to be heard. If you have a caller on the phone, they will automatically be put on hold. You can get the caller back by simply pressing #8 or by momentarily hanging up. Note: The LED will light during paging, and the AUDIO LED will flash with paging audio. B. Placing a Call On Hold To place a call on hold, simply press # then 6 (the letter O key on your keypad), two beeps should be heard confirming the call is on hold, then hang up. The call can then be taken on another phone elsewhere in your home or small business. Optional Music-On- Hold can be provided. C. Releasing a Call On Hold If you hang up the phone after placing a call on hold, simply coming off-hook with any phone will return you to the caller on hold. If you have placed a caller on hold (#6) or have announced a page (#7) and have remained off-hook, enter #8 or momentarily hang up to return to the caller on hold. If the caller hangs up while on hold, the SLP-4 can sense a CPC disconnect signal and will automatically release the line. 9

10 D. On-Hold Alarm Tones The SLP-4 can provide on-hold alarm tones to alert you that a caller has been left on hold. After each minute the call has been left on hold, the SLP-4 will momentarily mute the background music and output a double beep tone over the speakers. This feature can be disabled by setting DIP switch 2 to (see DIP Switch Programming page 8). E. Phone to Phone Intercom This feature allows you to first page someone over the speakers, then speak with them over the phone without the conversation being heard over the speakers. To perform this function, simply press #, then 7 (the P key on your keypad), announce your page, then press the numeric 0 key. Another phone coming off-hook will be instantly connected. If a phone call comes in during paging or a phone to phone intercom, a ringing warble sound will be heard in the phones. To answer the call, dial #8, or hang up both intercom phones to let the call ring in. F. System Bypass The system bypass allows you to use outside phone services (automated attendants, etc.) that require the use of the # key. Come off hook with any phone and enter #9, two confirmation beeps should be heard, hang up the phone. The SLP-4 will now ignore all Touch Tone commands on the next off-hook. G. Music Mute To mute the background music any time you are on the phone, simply enter #5. The background music will return when you enter #5 again or hang-up the phone. The MUTE LED will light while the background music is muted. Note: The music mute command (#5) should not be used in multi-line applications. H. Outside Line Access Mode (Dial 9) With DIP switch 3 in the position (see DIP Switch Programming page 8), simply coming off-hook will instantly give you the outside line. With DIP switch 3 in the position, you must dial a 9 to get an outside line. The SLP-4 s features remain the same in either mode. Note: Instant outside line access mode is for use with private dial tone. I. Door Chime (Doorbell Switch Input) With DIP switch 1 in the position (see DIP Switch Programming, page 8), the doorbell input terminals on the SLP-4 can be connected to a normally open switch (lighted or non-lighted doorbell buttons, etc.). When the switch is activated, the unit will momentarily mute the background music and provide a door chime/message sound over the speakers. Note: This input is not polarity sensitive and is designed to light standard 6-16V lighted doorbell switches. With DIP switch 1 in the position, the first triggered chime input on the SLP-4 can be connected to the C-200, C-1000B or C- 2000B normally open auxiliary relay contacts. When doorbox 1 on the C-1000B, or a door phone on the C-200 or C-2000B is activated, the SLP-4 will momentarily mute the background music and play message 1 Westminster 4 over the speakers. When doorbox 2 on the C-1000B, or door phone 2 on the C-2000B is activated, message 2 Ding Dong will be heard over the speakers. Entry phone 3 and 4 on the C-2000B will play Message 3 (Triangle 2) and Message 4 (Goblet Chime). This is ideal for determining which door the visitor is located at without having to answer the telephone. Note: The C-200, C-1000B or C-2000B must have the auxiliary contact mode programmed for custom ring cadence. For more information, refer to the Technical Practice. J. Loud Ringing The SLP-4 can momentarily mute background music and provide loud ringing (warble sound) over the speakers each time the incoming phone line rings. To enable this feature, short terminals labeled ENABLE. This input can also be connected to a SPST switch or time controlled relay for night ring applications. Note: With loud ringing enabled, if the incoming phone line rings during a page or phone to phone intercom, a short loud ring burst will be heard over the speakers every 15 seconds or until the line stops ringing. K. I.O. Communications (for Multi-Line Applications) The SLP-4 is designed to operate on a single phone line. If paging is required on two or more phone lines, connect one SLP-4 per line. Multiple SLP-4 s can be connected to the same Pre-Amp, Amp or Receiver. In this application the terminals labeled IO should be connected in parallel to each SLP-4. Caution: This connection is polarity sensitive. With the I.O. communication connected between each SLP-4, paging will be allowed on a first come, first serve basis. If paging is active on one SLP-4, any person attempting to page on another SLP-4 will hear a busy signal on their phone. 10

11 Quick Reference Guides Note: Make a photocopy of the Quick Reference Guides (below) and place one near your phones for quick reference to all of the SLP-4 touch tone commands. Feature: Model SLP-4 Quick Reference Guide Touch Tone Command: Page # 7 Hold # 6 Release Hold Phone-To- Phone Intercom System Bypass Music Mute Outside Line Access (use only with DIP switch 3 ) # 8 or momentarily hang-up # 7 then 0 # 9, then momentarily hang up # 5 9 Description: P for Page. Speak into the phone receiver and your voice will be heard throughout the house or small business over the speakers. Pressing #7 automatically places a caller on hold; to return to the caller after the page press #8 or momentarily hang-up. O for On-Hold. Allows you to place a caller on hold (with music), hang up and take the call on another phone in the house or small business. This releases the caller on hold, allowing you to converse with the caller. This allows you to talk with someone at another phone in the house or small business after a page, without the conversation being heard over the speakers. Enter #9, hear two beeps, and hangup. The SLP-4 will now ignore all commands on the next off-hook. This allows you to use outside phone services (automated attendants, etc.) that require use of the # key. This command allows you to mute the background music coming through your speakers for the duration of an incoming or outgoing call. Enter 9 to gain access to outside dial tone. Note: With DIP switch 3 in the position, you will instantly have outside line dial tone from off-hook (for use with private dial tone). Features Door Chime: Background music will mute and a door chime/ message sound will be heard over the speakers. Loud Ringing: When enabled, background music will mute and incoming call ringing (warble) sound will be heard over the speakers for the duration of the ring. On-Hold Alarm Tones: Each minute the call has been placed on hold, the background music will mute and a double On-Hold alarm tone will be heard over the speakers. Note: This feature can be disabled by setting DIP switch 2 to. Feature: Model SLP-4 Quick Reference Guide Touch Tone Command: Page # 7 Hold # 6 Release Hold Phone-To- Phone Intercom System Bypass Music Mute Outside Line Access (use only with DIP switch 3 ) # 8 or momentarily hang-up # 7 then 0 # 9, then momentarily hang up # 5 9 Description: P for Page. Speak into the phone receiver and your voice will be heard throughout the house or small business over the speakers. Pressing #7 automatically places a caller on hold; to return to the caller after the page press #8 or momentarily hang-up. O for On-Hold. Allows you to place a caller on hold (with music), hang up and take the call on another phone in the house or small business. This releases the caller on hold, allowing you to converse with the caller. This allows you to talk with someone at another phone in the house or small business after a page, without the conversation being heard over the speakers. Enter #9, hear two beeps, and hangup. The SLP-4 will now ignore all commands on the next off-hook. This allows you to use outside phone services (automated attendants, etc.) that require use of the # key. This command allows you to mute the background music coming through your speakers for the duration of an incoming or outgoing call. Enter 9 to gain access to outside dial tone. Note: With DIP switch 3 in the position, you will instantly have outside line dial tone from off-hook (for use with private dial tone). Features Door Chime: Background music will mute and a door chime/ message sound will be heard over the speakers. Loud Ringing: When enabled, background music will mute and incoming call ringing (warble) sound will be heard over the speakers for the duration of the ring. On-Hold Alarm Tones: Each minute the call has been placed on hold, the background music will mute and a double On-Hold alarm tone will be heard over the speakers. Note: This feature can be disabled by setting DIP switch 2 to. 11

12 Compatible Products Add Paging to Your Existing Phone Line Without an Expensive Phone System The SLP-1 Single Line Paging controller will allow you to page family members or co-workers from any phone in your home or small office. The pages can be heard over the same speakers that are installed for multi-zone music distribution. The SLP-1 connects in series with a single existing phone line. The unit has a built-in 2 watt amplifier, pre-amp output, music on hold input, intercom features and selectable loud ringing. The SLP-1 provides an input for a lighted doorbell switch, allowing a door chime to be heard over existing speakers. Page from several different phone lines by connecting multiple units. For more information, see DOD# 478. Add a Viking Entry Phone to an Existing Phone Line The C-200 allows single line telephones or a telephone system to share a phone line with a single Viking entry phone. Tenants may answer an entry phone call and converse with the visitor. The C-200 provides a Call Waiting tone when the phone line is in use. Tenants may call out to the entry phone for monitoring purposes. Auxiliary contacts are provided to operate a doorbell, or activate a camera, lights, etc. For more information, see DOD# 169. Add One or Two Doorboxes to an Existing Phone Line The C-1000B allows single line phones or phone systems to share a phone line with one or two Viking doorboxes or paging amplifiers. The C-1000B provides two Touch Tone controlled relays to operate door strikes or gate openers and provides doorbox triggered CCTV camera switching. Viking doorboxes and paging amplifiers can be used on single line, residential or home office applications as well as on fully loaded systems, because they are no longer limited to installation on unused trunk ports. For more information, see DOD# 168. Add 1-4 Entry Phones and Doorstrike Control to an Existing Phone Line The C-2000B allows single line phones or phone systems to share a phone line with 1-4 entry phones. Tenants may answer an entry phone call, converse with the visitor and activate a contact closure to control electronic gates or door strikes. The C-2000B provides entry phone Caller ID and will also provide Call Waiting Caller ID and a Call Waiting tone when the phone line is in use. Tenants may gain entry at each gate by entering a touch tone keyless entry code. Tenants may call out to each entry phone for monitoring purposes. An auxiliary input is also available for connecting a lighted doorbell switch, a common garage door opener/receiver or an auxiliary keyless entry keypad. For more information, see DOD# 156. Product Support Line Fax Back Line Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes. 12 DOD# 479 Printed in the U.S.A. ZF Rev A