ITX-i290D. Soldered onboard Intel Atom D GHz CPU. 2 x Realtek 8111DL Gigabit Ethernet controller

Transcription

1 Form Factor Mini-ITX ITX-i0D Mini-ITX Industrial Motherboard CPU Soldered onboard Intel Atom D0.GHz CPU Quick Installation Guide Version.0 Chipset Intel ICH8M Video 8bit LVDS/ Analog RGB LAN x Realtek 8DL Gigabit Ethernet controller Audio Realtek ALC Audio CODEC, Mic-in/Line-in/ Line-out I/O PCI/ SATA/ USB.0/ COM/ DIO/ Mini-card Technical Support If you have any technical difficulties, please consult the user s manual first at: ftp://ftp.arbor.com.tw/pub/manual Please do not hesitate to call or our customer service when you still can not find out the answer. [email protected] Copyright 0 All Rights Reserved. Tested To Comply With FCC Standards FOR HOME OR OFFICE USE P - -

2 Packing List Before you begin to install your single board, please make sure that the following materials have been shipped: x ITX-i0D Mini-ITX industrial motherboard x Driver CD x Quick Installation Guide x I/O bracket x SATA cable If any of the above items is damaged or missing, contact your vendor immediately. Ordering Information ITX-i0D CBK-08-0D-00 Intel Atom D0 Embedded Mini-ITX Motherboard Cable Kit x USB Cable x Parallel x SATA Cable x LPT Cable x IDE Cable x COM Cable - -

3 The Installation Paths of CD Driver Windows 000 & XP Driver Path CHIPSET \Driver\Chipset\Intel\Infinst VGA \Driver\Chipset\Intel\Graphics\\KXP LAN \Driver\LAN\Realtek\PCIE_LAN\KXP AUDIO \Driver\Audio\Realtek\Azalia\KXP Windows 7 Driver CHIPSET VGA LAN AUDIO Path \Driver\Chipset\Intel\Infinst \Driver\Chipset\Intel\Graphics\\Win7 Bit \Driver\Chipset\Intel\Graphics\\Win7 Bit \Driver\Lan\Realtek\PCIE_LAN\Win7 \Driver\Audio\Realtek\Azalia\KXP - -

4 Specifications Form Factor CPU Chipset System Memory VGA/ LCD Controller Ethernet I/O Chips BIOS Audio IDE Interface Serial ATA Serial Port Parallel Port KBMS Universal Serial Bus DIO Expansion Interface Power Requirement Operation Temp. Operating Humidity Watchdog Timer Mini-ITX industrial motherboard Soldered onboard Intel Atom D0.GHz CPU Southbridge : Intel ICH8M x 00-pin DDR SO-DIMM vertical type Socket up to GB at 7/800 MHz Intel Graphics Media Accelerator 0 graphics core w/ Analog RGB and 8bit LVDS (Dual independent display) x Realtek 8DL Gigabit Ethernet controller ITE IT878F AMI 8Mb Flash BIOS Realtek ALC Audio CODEC, Mic-in/Line-in/Line-out x Ultra ATA 00 port, support IDE devices (pin) x Serial ATA ports with 00MB/s HDD transfer rate x RS- ports, x RS-//8 selectable port SPP/EPP/ECP mode x Standard PS/ Keyboard and Mouse 8 x USB.0 ports (on board USB ports) 8-bit programmable Digital Input/Output, in/ out x PCI slot x Mini-card slot -pin ATX V connector 0 ~ 0 C ( ~ 0 F) w/ cooling fan 0 ~ 0 C (non-condensing) -level Reset Dimension (L xw) 70 x 70 mm (.7 x.7 ) - -

5 Rear Panel PS/ Mouse PS/ Keyboard COM VGA COM LAN LAN Line In (Rear) Line Out (Front) COM USB.0 x Mic in (Center/SUB) MainBoard Layout JKBMS JATXPWR DIMMA JSFAN JCOM JVGA JCOM JCOM JCOM JP JCOM JLV JSEL JSEL JCOM JLV JP JUSBLAN LVDS-COMN JC JBL JBL Intel Atom D0 CPU ICH8M JHDD SATA SATA IDE JUSBLAN JAUDIO JPRNT PE BAT JDIO USB BIOS PCI PCI JCMOS USB JAT JPANEL Note: represents the st pin. - -

6 Jumpers/Connectors Quick Reference Jumpers Label JCMOS JAT JLV JLV JBL JBL Function Clear CMOS Setting AT/ATX Power Switch Selection LCD Power Voltage Select LCD Backlight Inverter Voltage Select Backlight Power ON/OFF Select LCD Backlight Brightness Adjust Connectors Label JSFAN JATXPWR JHDD PCI PE IDE SATA ~ JPANEL USB ~ JCOM ~ JSEL ~ JP JP JCOM ~ JDIO JPRNT LVDS- COMN JC Function Fan Power Connector Power Connector SATA Power Connector -bit PCI Slot Mini PCI-E Slot Primary IDE Connector Serial ATA Connectors Switches and Indicators USB Port Connectors Serial Port Connectors JCOM RS-//8 Select (Optional) Voltage Switch Header for JCOM Voltage Switch Header for JCOM RS- Connectors Digital I/O Connector Parallel Port Connector LVDS LCD Connector LCD Backlight Inverter - -

7 - 7 - Jumpers & Connectors Locations JUSBLAN JUSBLAN JAUDIO PCI JPANEL USB USB IDE SATA SATA JHDD JSFAN JATXPWR JP LVDS-COMN JCOM BIOS PCI PE 7 8 JCOM JSEL JSEL JP 7 8 JCOM JCOM 0 JDIO JPRNT JC JCMOS JAT 7 JLV 8 JLV JBL 0 JBL JCOM JCOM 0

8 Jumpers Jumper Settings The jumper is short (closed) when the jumper cap is placed on pins. If not, that means the jumper is open. Mode Short Backlight Power OFF Open Backlight Power ON open short (closed) - short (closed) - short (closed) JCMOS: Clear CMOS Setting () Connector type:.mm pitch x-pin headers. Mode - Keep CMOS (Default) - Clear CMOS JAT: AT/ATX Power Mode Selection (7) Connector type:.mm pitch x-pin headers. - AT Mode - ATX (Default) JLV: LCD Panel Voltage Select (8) The voltage PVDD of LCD panel could be selected by JLV in +V or +.V. Connector type:.mm pitch x-pin headers. Voltage - +.V (Default) - +V JLV: LCD Backlight Inverter Voltage Select () The Backlight Inverter voltage of LCD panel could be selected by JLV in +V or +V. Connector type:.mm pitch x-pin headers. Voltage JBL: LCD Backlight Brightness Adjust () Connector type:.mm pitch x-pin headers. Based Address - - Increase Brightness (Default) Open Short Decrease Brightness Short Open Connectors JSFAN: Fan Power Connector () JSFAN is a -pin headers for the fan. The fan must be a +V fan. GND +V Description FAN_Detect JATXPWR: Power Connector () JATXPWR supplies the CPU operation ATX +V (Vcore). +V +V GND GND Description JHDD: SATA Power Connector () Connector type:.mm pitch x-pin wafer one wall connector. - +V Description - +V (Default) JBL: Backlight Power On/Off Select (0) Connector type:.mm pitch x-pin headers. +V +.V GND +V Note: Be careful not to plug wrong cable in this connector by mistake for its pin definition is different from ordinary power connector

9 PCI: -bit PCI Slot () The board is equipped with one standard PCI slot. PCI stands for Peripheral Component Interconnect, and it is a bus standard for expansion cards. This PCI slot is designated as -bit. PE: Mini PCI-E Slot () This mainboard is equipped with Mini PCI-E Slot. USB~: USB Port Connectors (0, ) Connector type:.mm pitch x-pin headers. Desc. Desc. +V +V USB- USB7- USB+ USB7+ 7 GND 8 GND N/C (Key) 0 N/C 0 JCOM~: Serial Port Connectors (,, ) Connector type: Double stacks D-Sub -pin male. JCOM supports RS-//8 (Optional); JCOM and JCOM only support RS-. IDE: Primary IDE Connector () Connector type:.00mm pitch x box headers. The board has an integrated IDE controller that provides PIO Mode 0~, Bus Master, and Ultra DMA//00 functionally. It has on IDE connector which can connect a master and a slave drive, you can connect up to two ATA devices. JCOM JCOM JCOM RS- RS- RS-8 SATA~: Serial ATA Connectors (7, 8 ) High speed transfer rates (.0 Gbit/s). GND TX+ TX- GND RX- RX+ 7 GND Description JPANEL: Switches and Indicators () It provides connectors for system indicators that provides light indication of the computer activities and switches to change the computer status. Connector type:.mm pitch x-pin headers. 7 Carrier detect (DCD) TX- TX- Received data (RXD) TX TX Transmitted data (TXD) RX NC Data terminal ready (DTR) RX- NC Signal ground (GND) GND GND Data set ready (DSR) NC NC 7 Request to send (RTS) NC NC 8 Clear to send (CTS) NC NC Ring NC NC Description Description N/C (Key) Power_LED+ HD_LED+ Power_LED+ HD_LED- Power_LED- 7 RESET GND 8 Power RESET 0 Power GND 0 - -

10 JSEL~: JCOM RS-//8 Select (, ) (Optional) JSEL Connector type:.mm pitch x-pin headers. Mode RS- (Default) RS JSEL Connector type:.mm pitch x-pin headers. Mode RS- (Default) RS JP: Voltage Switch Header for JCOM (7) This header is for controlling the of JCOM to switch between Ring or V RS RS-8 - Short Open Open - Open Short Open - Open Open Short JCOM~: RS- Connectors (, 0, ) Connector type:.mm pitch x-pin headers. Desc. Desc. -PDCD PSIN PSOUT -PDTR data GND -PDSR 7 -PRTS 8 -PCTS -PRI 0 V (JCOM/) V (JCOM) 0 JDIO: Digital I/O Connector () This connector offers pairs of digital I/O whose functions and addresses are set in BIOS. The default address is AH: Output bit-0~, AHL Input bit-0~. Connector type:. mm pitch x-pin headers Description Description V DI-0 DO-0 DI- DO- DI- 7 DO- 8 DI- DO- 0 GND JPRNT: Parallel Port Connector () Connector type:.mm pitch x-pin headers. Description Description STB# AFD# 0 - Closed - Closed - Closed - Closed =V =Ring (Default) JP: Voltage Switch Header for JCOM (8) This header is for controlling the of JCOM to switch between Ring or V. =V =Ring (Default) PTD0 ERROR# PTD INIT# 7 PTD 8 SLIN# PTD 0 GND PTD GND PTD GND PTD GND 7 PTD7 8 GND ACK# 0 GND BUSY GND PE GND SELECT N/C (Key) - 0 -

11 LVDS-COMN: LVDS LCD Connector () This connector supports only 8-bit single-channel panels up to WXGA ( x 78). Desc. Desc. PVDD (+.V or +V) NC PVDD (+.V or +V) NC GND GND 8 GND 7 NC 0 LVDS_TX0- (Differential LVDS_TX0+ (Differential NC GND GND NC 8 LVDS_TX- ( (Differential LVDS_TX+ (Differential NC 7 GND 0 GND NC LVDS_TX- (Differential LVDS_TX+(Differential NC GND GND NC 8 0 LVDS_CLK- (Differential LVDS_CLK+(Differential 7 NC +V GND IC_CLK SMDATA +.V SMCLK NC 8 NC 7 0 IC_DATA 0 PVDD (+.V or +V) PVDD (+.V or +V) JC: LCD Backlight Inverter () This connector is for connecting to LCD for providing backlight control function. Description +V/ +V +V/ +V N/C N/C Backlight On Brightness Adjust 7 GND 8 GND - -