Installation Instructions

Size: px

Start display at page:

Download "Installation Instructions"

Emma Haynes
7 years ago
Views:

1 Installation Instructions E (Plastic showerhead) E19-120A (Stainless steel showerhead) E19-120SS (All Stainless Steel) Drench Shower - Horizontal Supply Table of Contents Pre-Installation Information Assembly of Components - Plastic Showerhead Parts List - Plastic Showerhead Assembly of Components - Stainless Steel Showerhead...5 Parts List - Stainless Steel Showerhead Assembly of Components - All Stainless Steel Unit Parts List - All Stainless Steel Unit IMPORTANT This equipment should be inspected, tested, and recorded weekly to maintain proper operation. Main water supply to the eye wash should be ON at all times. This installation manual and parts list should be filed by the owner s maintenance department E Rev. N; EN Bradley Corporation Page 1 of 6 5/20/03 P.O. Box 309, Menomonee Falls, WI TEL BRADLEY FAX

......................4 Assembly of Components - Stainless Steel Showerhead...5 Parts List - Stainless Steel Showerhead.................5 Assembly of Components - All Stainless Steel Unit.

2 Drench Shower - Horizontal Supply Pre-Installation Information Operation The drench shower is easily activated by pulling the triangular pull rod downward, and deactivated by pushing the triangular pull rod upward. Components Showerhead: The showerhead has a 254mm (10") diameter. Shower Valve: The 1" NPT stay-open, chrome-plated brass (stainless steel on S19-120SS) ball valve is operated by a stainless steel pull rod with triangle handle. Water Supply: Water supply connection is 1" BSP horizontal. Pipe and Fittings: Pipe and fittings are galvanized steel, coated with Bradtect safety yellow (stainless steel on S19-120SS). Check Contents Separate all parts from packaging and check each part with Figure 2a and the Parts List on page 4 (for shower with plastic showerhead) or Figure 2b and the parts list on page 5 (for shower with stainless steel showerhead) or Figure 2c and parts list on page 6 (for shower with all stainless steel). Make sure all parts are accounted for before discarding any packaging material. If any parts are missing, do not attempt to install your Bradley Drench Shower until you obtain the missing parts. Bradley Drench Shower Warranty Bradley Corporation warrants to commercial and institutional purchasers only each fixture free from defects in material and workmanship under normal use and service upon the following terms and conditions: 1. We will replace, without charge, any part which proves to be defective within one year from the date of our invoice at our option, F.O.B. Menomonee Falls, Wisconsin. 2. This warranty does not cover installation or any other labor charge and does not apply to fixtures which have been damaged by accident, abuse or improper maintenance. 3. The repair or replacement of the defective fixtures as stated in this warranty shall constitute the sole remedy of the purchaser, and the sole liability of the Bradley Corporation under this warranty. Bradley Corporation shall not otherwise be liable under any circumstances for incidental, consequential or indirect charges caused by defects in fixtures or any delay in the repair or replacement thereof. 4. This warranty extends only to commercial and institutional purchases and does not extend to any others, including consumer, customers of commercial and institutional purchasers. 5. This warranty is in lieu of all other warranties expressed or implied, including any implied warranty of merchants ability or fitness for a particular purpose, or otherwise. 6. Bradley emergency fixtures are to be used as a supplement to first aid treatment. Bradley Corporation cannot guarantee that when used this emergency equipment will prevent serious injury or the aggravation of existing or prior injuries. No other warranties, expressed or implied are authorized, provided or guaranteed by Bradley Corporation. 2 5/20/03 Bradley Corporation E Rev. N; EN

Shower Valve: The 1" NPT stay-open, chrome-plated brass (stainless steel on S19-120SS) ball valve is operated by a stainless steel pull rod with triangle handle.

3 Drench Shower - Horizontal Supply Supplies Required: Teflon tape Pipe sealant Piping to 1" BSP water supply inlet on unit Adequate supply pipe supports Minimum 102mm (4") drain to accommodate 115 liters per minute discharge for drench shower waste. NOTE: Flush the water supply line before beginning installation. Step 1: Assemble drench shower 1. Assemble drench shower components as shown in Figure 2a on page 4 (for shower with plastic showerhead) or Figure 2b on page 5 (for showerhead with stainless steel showerhead) or Figure 2c on page 6 (for shower with all stainless steel). NOTE: The bottom edge of the showerhead should be 2134mm (7'-0") from the floor. 2. Apply pipe sealant or tape (supplied by installer) to all male-threaded pipe joints. The plastic showerhead should be assembled to the street elbow with teflon tape. IMPORTANT: Some teflon sealants may cause stress cracks in the plastic showerhead leading to failure. Use teflon tape for sealing the showerhead. Step 2: Connect water supply Figure 1 IMPORTANT: Do not rely on Bradley s Drench Shower to support supply piping. 1. Connect water supply piping to 1" BSP inlet on unit (piping supplied by installer). Provide adequate supports (supplied by installer) for supply pipe using pipe hangers or other means. 2. Mount safety sign to wall or pipe using sign mounting hardware supplied. 3. Open water supply lines. Test for leaks and adequate water flow. Bradley Corporation E Rev. N; EN /20/03 3

Assemble drench shower components as shown in Figure 2a on page 4 (for shower with plastic showerhead) or Figure 2b on page 5 (for showerhead with stainless steel showerhead) or Figure 2c on page 6

4 Drench Shower - Horizontal Supply Assembly of Components (E19-120) 1" BSP SUPPLY INLET (BSP THREADS ARE NOTED WITH BLACK LINE ON THREADS) NOTE: Items 1A-1B come preassembled as Item 1. Items 4A-4E come preassembled as Item 4. Figure 2a Service Parts List Item Part No. Qty Description Item Part No. Qty Description 1 S PLASTIC SHOWERHEAD ASSY. 1A SHOWERHEAD SHELL 1B BAFFLE 1C SCREW STREET ELBOW 1" NPT LK 1 PIPE 1" NPT X 293mm LG. 4 S30-059B 1 STAY-OPEN BALL VALVE 1" NPT 4A S27-278B 1 1" BALL VALVE 4C HANDLE 4D DC 1 LOCKWASHER 4E WASHER, FLAT FRICTION A 1 PULL ROD - 24" LONG JAM NUT (SERVICE PART) 7* EMERGENCY TAG 8* CURTAIN HOOK 9* E 1 SAFETY SIGN 4B STOP BRACKET * Not Shown 4 5/20/03 Bradley Corporation E Rev. N; EN

1A 154-057 1 SHOWERHEAD SHELL 1B 155-005 1 BAFFLE 1C 160-245 3 SCREW 2 169-723 1 90 STREET ELBOW 1" NPT 3 113-006LK 1 PIPE 1" NPT X 293mm LG.

5 Drench Shower - Horizontal Supply Assembly of Components (E19-120A) NOTE: Items 1A-1F come preassembled as Item 1. Items 4A-4E come preassembled as Item 4. 1" BSP SUPPLY INLET (BSP THREADS ARE NOTED WITH BLACK LINE ON THREADS) Figure 2b Service Parts List Item Part No. Qty Description Item Part No. Qty Description 1 S STN. STL. SHOWERHEAD ASSY. 1A SHOWERHEAD SHELL 1B DIFFUSER 1C ADAPTOR 1D DP 1 WASHER 1E SCREW STREET ELBOW 1" NPT LK 1 PIPE 1" NPT X 293mm LG. 4 S30-059B 1 STAY-OPEN BALL VALVE 1" NPT 4B STOP BRACKET 4C HANDLE 4D DC 1 LOCKWASHER 4E WASHER, FLAT FRICTION A 1 PULL ROD - 24" LONG JAM NUT (SERVICE PART) 7* EMERGENCY TAG 8* CURTAIN HOOK 9* E 1 SAFETY SIGN 4A S27-278B 1 1" BALL VALVE * Not Shown Bradley Corporation E Rev. N; EN /20/03 5

1A 187-053 1 SHOWERHEAD SHELL 1B 155-008 1 DIFFUSER 1C 153-312 1 ADAPTOR 1D 125-001DP 1 WASHER 1E 160-138 2 SCREW 2 169-723 1 90 STREET ELBOW 1" NPT 3 113-006LK 1 PIPE 1" NPT X 293mm LG.

6 Drench Shower - Horizontal Supply Assembly of Components (E19-120SS) NOTE: Items 1A-1F come preassembled as Item 1. Items 4A-4B come preassembled as Item 4. 1" BSP SUPPLY INLET Figure 2c Service Parts List Item Part No. Qty Description Item Part No. Qty Description 1 S STN. STL. SHOWERHEAD ASSY. 1A SHOWERHEAD SHELL 1B DIFFUSER 1C ADAPTER 1D DP 1 WASHER 1E SCREW STREET ELBOW 1" NPT MN 1 PIPE 1" NPT X 305mm LG. 4A S " BALL VALVE 4B HANDLE A 1 PULL ROD - 24" LONG ADAPTER JAM NUT (SERVICE PART) 8* CURTAIN HOOK 9* E 1 SAFETY SIGN 10* EMERGENCY TAG 4 S STAY-OPEN BALL VALVE 1" NPT * Not Shown 6 5/20/03 Bradley Corporation E Rev. N; EN

1A 187-053 1 SHOWERHEAD SHELL 1B 155-008 1 DIFFUSER 1C 153-235 1 ADAPTER 1D 125-001DP 1 WASHER 1E 160-410 2 SCREW 2 169-854 1 90 STREET ELBOW 1" NPT 3 113-006MN 1 PIPE 1" NPT X 305mm LG.

Installation E19-310. Combination Drench Shower/Eyewash. Table of Contents

Installation E19-310. Combination Drench Shower/Eyewash. Table of Contents Installation E19-310 Combination Drench Shower/Eyewash Table of Contents Pre-Installation Information...................... Installation Instructions.........................3 Assembly of Components.......................