Making Manufacturers More Competitive. Selection Guide. AIRMIX manual spray equipment.

Transcription

1 Making Manufacturers More Competitive Selection Guide AIRMIX manual spray equipment

2 EXEL North america EXEL North America, located in Plymouth, Michigan is the leader of high value added custom and standard solutions for controlled applications of powders and thick or thin fluids in the industrial and automotive markets. Our success is possible because of our strong commitment to the growth of our employees, who are carefully chosen for their integrity and mission-to-serve with a sense-of-urgency attitude. We are committed to complete customer satisfaction! We vow to develop the latest innovations, maintain close relationships with key influential's in the industry and deliver the best solutions for our customers. John Patry President EXEL North America EXEL history dates back to 1925 with the introduction of the first airspray gun from KREMLIN. SAMES was founded in 1947 and REXSON in EXEL expanded into North America in EXEL North America consists of nearly 100 employees with offices in Plymouth, Michigan; Scarborough, Ontario, Canada; and Monterrey, Mexico. We have two distinct sales and service teams for our Wood & General Industry markets and our Tier 1 & Automotive markets. EXEL North America is a wholly owned subsidiary of EXEL INDUSTRIES, a Global company with 21 manufacturing centers, two in the US, and 23 subsidiaries, three in North America. For more information go to People: Integrity Solution Service Products: Quality Innovation Performance Delivering Controlled Applications Liquid Finishing - Powder Coating - Sealants - Adhesives Lubricants - Mold Release Agents - Potting - Plural Component Materials 2 Making Manufacturers More Competitive

3 Making Manufacturers More Competitive CONTENTS TABLE OF CONTENTS AIRMIX world class finishing since Characteristics of spraying technologies 5 AIRMIX spraying 6-7 Hot spraying 8-9 Xcite AIRMIX guns MVX AIRMIX guns 12 AIRMIX aircaps 13 Accessories for AIRMIX guns Selection Table - AIRMIX Pumps 18 Intensive AIRMIX Pumps Selection Table - Flowmax Pumps Flowmax Pumps Recommendations - Advice 35 Heaters Accessories for hot spraying 38 EXEL Advanced Technology 40 Training 41 EXEL Industries... An International Presence 42 EXEL... A North American Presence

4 AIRMIX World Class Finishing since 1975 Creator of the Airmix technology 35 years ago, KREMLIN REXSON always proved its ability to stay innovative. Pioneer of environmental protection as early as 1975, KREMLIN REXSON has been developing technology capable of combining quality of spraying and productivity, altogether with a very high transfer efficiency, to achieve a minimal overspray. Moreover, the protection and comfort of the operator have always been major concerns of our teams. Very present at its inception on the wood market, AIRMIX progressively proved itself in markets as demanding as Railways, Aeronautics or Rolling equipment. Well ahead regarding respect for the environment, AIRMIX now imposes itself naturally on green markets like that of windmills, by considerably reducing their grey energy levels on application of paints, thanks to a very high transfer efficiency and a remarkable application quality. Others technologies AIRMIX Transfer Efficiency 0% 100% 86% Others technologies AIRMIX Particle speed 0 10m/s O.7m/s Others technologies AIRMIX Air consumption 0 30m³/h with AIRMIX 3m³/h The additional air is injected before the locus of atomization, it results in a very stable fan and a perfectly even build on all sorts of parts to be sprayed. without AIRMIX With the other medium pressure systems, the additional air is injected into or beyond the locus of atomization, which leads to turbulent air flows, more overspray and less finish quality. Various generations of the KREMLIN REXSON AIRMIX gun honor this philosophy. The MR, MRX, MX and the MVX each contributed to the development of this brand in its different global markets. AIRMIX R E G 1975 I S T E R E D Xcite TM AIRMIX GUN 4

5 characteristics of spraying technologies The Benefits Of AIRMIX Airmix has become a standard in the industry by providing better atomization, low paint particle velocities, low air consumption and extremely high transfer efficiencies. Airmix - Superior to conventional, low pressure, and airless spraying. Paint Velocity - Reduces booth maintenance The paint velocity has a direct impact on performance: the higher the velocity, the greater the amount of overspray and bounceback, which combine to quickly pollute the booth. As can be seen from the graph on the right, the particle speed with Airmix is much lower than with all other systems. AIRMIX Air-Assisted Airless Airless HVLP Conventional Slow Fast Transfer Efficiency - Saves on paint costs Users of Airmix achieve the highest transfer efficiency available. Efficiencies on different types of manual spray equipment are: Conventional Airless HVLP Air-Assisted Airless AIRMIX Electrostatic AIRMIX Low High Air Consumption - Lower energy costs Airmix uses less air for atomization air than any other high quality spray system. Airmix works well with smaller air compressors, lower production air pressure and lower compressed air volumes. This generates major savings in compressed air cost and reduces air compressor maintenance. AIRMIX Air-Assisted Airless Airless Conventional HVLP Low High Fine Atomization - Excellent finish Airmix uses a specially designed aircap to provide a smooth and even finish every time. The aircap helps to evenly atomize the paint as it leaves the fluid tip. This even atomization allows the paint to be broken down into smaller particles which provides the best coat with minimal defects or orange peel. HVLP Airless Air-Assisted Airless AIRMIX 5

6 AIRMIX spraying with fan adjustment Principle AIRMIX (1) was designed to create a new spraying technology which combines the advantages of the conventional and AIRLESS spraying technologies. In order to do this, AIRMIX associates middle pressure spraying and an indirect addition of atomization air (at a very low pressure), which leads to outstanding fan control. The outcome of this association is a supercharge of air at the locus of atomization, right after the outflow from the tip, which results in a perfectly controlled and adjustable fan. (1) AIRMIX is a registered trademark of KREMLIN. New AIRMIX spraying The new AIRMIX spraying technology optimizes even more the advantages of conventional and AIRLESS spraying. with AIRMIX The additional air is injected before the locus of atomization, it results in a very stable fan and a perfectly even build on all sorts of parts to be sprayed. without AIRMIX With the other medium pressure systems, the additional air is injected into or beyond the locus of atomization, which leads to turbulent air flows, more overspray and less finish quality. The equipment The AIRMIX range is designed for manual, automatic and electrostatic spraying. The use of AIRMIX systems is optimized in a pressure range between 30 and 200 bar, which implies the use of pumps with a pressure ratio between 8 and 40. A standard AIRMIX equipment consists of a pump, a gun and two hoses. The pump is equipped with a suction rod, that is suitable for any container The gun is connected up to the pump by two hoses: a small diameter, flexible, solventresistant fluid hose, an antistatic rubber air hose for the atomization air. Cold Airmix Hot Airmix 6

7 KREMLIN, creator of the AIRMIX technology launches its next generation AIRMIX guns, which eliminate more than 80 % of overspray, reduce coating consumption by up to 50 % and offer an outstanding spraying quality. The new AIRMIX concept was developed, bearing customers needs in mind, bringing many new benefits to the end-user. In addition to the exceptional adaptability offered by the fan adjustment system, KREMLIN has taken particular care over the ergonomics of the new MVX: a user-friendly grip on the handle, a light weight gun, a more flexible trigger, better visual control on your application. The MVX features a fan adjusting system to keep the same powerful and unsurpassed atomization quality whatever the shape of the part to be painted. 8 6 % TRANSFER EFFICIENCY! The advantages of AIRMIX Outstanding finish quality Paint savings by 35% and more Higher efficiency of application for higher productivity Reduced overspray and particles rebounds Reduced spray booth maintenance Reduced solvents emission Feeding pumps Outstanding working conditions A wide range of products adaptable to production needs Quick payback Products recommended Solvent or water-based products Varnishes Lacquers Polyurethanes Two-component products High solids Stains UV-curing The MVX gun can be fed by various pumps from the KREMLIN range 10.14/10.14S A2 FLOWMAX PU 2160F CYCLOMIX tm MULTI 7

8 Hot spraying The advantages of hot paint spraying Hot spraying Regularity of efficiency Solvent savings Reduction of the risk of runs Viscosity Better finish quality Reduction of the rejects due to dirt Faster preparation Principle By raising the temperature of a fluid, you reduce its viscosity: for instance, heating paint up to 60 or 80 C will have the same result as using solvent. Hot paint spraying is also a good solution to maintain paints at a regular temperature, preserving them from the variations of temperature in a workshop all and every day. Diagram 1 Temperature Apply more paint per pass As the discharged paint exits the gun, two factors raise the viscosity of the paints. The accelerated evaporation of the hot solvents and the cooling of the resin. The net effect is the ability to apply more paint per pass without runs. KREMLIN s advice The speed of circulation is usually adjusted to renew the content of each hose section every 30 seconds. Given a hose with a diameter of 10mm : Its internal volume is about 80 cm3 per metre. Now, if we use a pump having a capacity of 20 cm3, we will have to operate valve on 7 or 9 to obtain a rhythm of the pump of four strokes every 30 seconds, that is to say eight strokes per minute. 8

9 Process Cold paint is discharged into the heater (4) under the action of pressure. It is instantly warmed to the selected heat and reaches the spray gun (3) after passing through the filter (8) at a similar temperature. Under pressure, the heated paint goes back to the suction valve through the Y-fitting (5) and the fluid hose (6), which leads to the continuous circulation of the heated paint throughout the installation. This circulation process can be controlled by operating the circulation valve (7) or the back pressure regulator (9). However, using circulation too intensively is useless and might also damage the packings ensuring the pump tightness. Do not forget that their lifespan is based on the total volume of paint that has circulated throughout the pump. It is always the same volume of paint, inside the hoses, that is heated. The paint in the container (2) remains cold. Example 1 Configuration with One-Pass hot spraying Example 2 Configuration with HP, BD and AD hot spraying Hot spraying As soon as the operator presses the trigger of the gun, hot paint flows out from the tip, which increases the flow rate: the pump (1) automatically sucks an equivalent unit of cold paint to be heated. But the temperature on the level of the gun remains unchanged since this unit of paint is instantly heated while passing through the heater (4). Whether the operator uses the system or not, it will ensure the delivery of hot paint to the gun. Examples of hot paint application 1. Thick coating material - Hot spraying between 60 C (140 F) and 70 C (158 F) 2. Medium diluted paint Hot spraying between 60 C (140 F) and 70 C (158 F) 3. Medium diluted paint Hot spraying between 30 C (86 F) and 40 C (104 F) It makes it possible to spray paint without diluting it. It cools as soon as it leaves the gun and regain it original thicker consistency when deposited. Only one pass is necessary, even when you apply thicker materials, which implies: lesser risk of runs - a glossier film - a less porous covering - no dilution costs - less pollution due to the use of solvents - greater facility to keep the film dust free - the ideal system to use when the operator lacks experience. Paint becomes extremely fluid. Therefore it can be sprayed at very low pressure. Besides, a major part of the solvents evaporates as the paint leaves the gun: its viscosity increases when it is deposited on the part at ambient temperature. Less overspray - less loss of paint- lesser risk of runs - greater facility to keep the film dust-free - improved healthiness in the workshop - better temperature regulation - greater security of application. The viscosity of the paint is slightly reduced. A lesser quantity of the solvents evaporates. Paint begins to cool as it leaves the gun. There is more security with this sort of application, because the temperature of the heated paint remains unchanged whatever the time in the day or the season may be - Keeping the film dust-free is also highly facilitated. 9

10 Xcite TM STRENGTHES Choice of Fine or Xtra Fine Finish series tip New AIRMIX aircap for superior finish quality Precise large fan width adjustment The following materials may be sprayed with the new Xcite Airmix gun Solvent or water based materials Lacquers, varnishes Polyurethanes Two components High solids Stains UV curing WB glues Ultralight and comfortable trigger Ergonomic design for comfort fit and feel Stainless steel fluid passage Swivel fitting for improved maneuverability A complete Airmix package A great Airmix gun requires additional equipment working together to deliver exceptional performance that our customers expect. KREMLIN REXSON pumps are carefully crafted to minimize pulsation, maintenance at just the right pressure and flowrate. Our exclusive Flowmax Superlife technology provides unparalleled advantages in terms of reliability and performance. 10

11 Choose your own Xcite Xcite spray gun with fluid swivel fitting Aircap Tip Gun type Maximum fluid VX 24 K HVLP type size inches / (mm) pressure psi / (bar) Xcite psi (120 bar) To be ordered separately (see table) Xcite psi (200 bar) Seat Stainless steel Carbide VX 24 K HVLP Aircap AIRMIX FINE FINISH AND XTRA FINE FINISH TIPS Water output oz/mn (l/mn) Screen marking Average width of fan at a distance of 9.9 inches (25cm) Pressure psi / (bar) for filter Tip size inches (mm) 507 psi (35 bar) 1015 psi 1740 psi 2900 psi (70 bar) (120 bar) (200 bar) Gun Pump mm mm mm mm mm (2.03 cm) 0.81 (2.05 cm) mm mm mm mm (3.03 cm) 1.02 (3.05 cm) 1.20 (3.07 cm) mm mm mm mm mm 4 2 or (4.03 cm) 1.59 (4.05 cm) 1.60 (4.07 cm) 1.61 (4.09 cm) 1.62 (4.11 cm) 1.62 (4.13 cm) mm mm mm mm mm 4 4 or (6.03 cm) 2.38 (6.05 cm) 2.38 (6.07 cm) 2.39 (6.09 cm) 2.4 (6.11 cm) 2.41 (6.13 cm) 2.42 (6.15 cm) mm mm mm mm mm 6 6 or (9.03 cm) 3.56 (9.05 cm) 3.57 (9.07 cm) 3.57 (9.09 cm) 3.58 (9.11 cm) 3.59 (9.13 cm) 3.60 (9.15 cm) mm mm mm mm mm 6 8 or (12.07 cm) (12.09 cm) (12.11 cm) (12.13 cm) (12.15 cm) 4.79 (12.17 cm) mm mm mm mm mm 12 8 or (14.05 cm) (14.07 cm) (14.09 cm) (14.11 cm) (14.13 cm) (14.15 cm) 5.75 (14.17 cm) mm mm mm mm mm (18.13 cm) (18.15 cm) 7.15 (18.17 cm) mm mm mm mm mm (20.07 cm) (20.09 cm) (20.11 cm) (20.13 cm) (20.15 cm) 7.94 (20.17 cm) 7.95 (20.19 cm) mm mm mm mm mm (25.13 cm) mm mm mm mm mm (30.11 cm) (30.13 cm) (30.15 cm) (30.17 cm) (30.19 cm) mm mm mm mm mm (40.17 cm) mm mm mm mm mm (45.11 cm) (45.15 cm) (45.17 cm) (45.19 cm) Xcite Spray Guns Tips highlighted in yellow are also available as Xtra Fine Finish series type, which are designed to improve atomization of polyurethanes, waterbased and HS coatings. To order a tip, replaces the crosses read in the table, in 134.5xx.xx4 for a Fine Finish or 135.5xx.xx2 for an Xtra Fine Finish tip. For example: order (Fine Finish) or (Xtra Fine Finish) for a tip. KITS FOR AIRMIX Xcite SPRAY GUNS WITH SWIVEL FITTINGS Xcite 120 Xcite 200 Aircap Type VX 24 K HVLP VX 24 K HVLP Tip To be ordered separately (see table) To be ordered separately (see table) Fluid hose feet / (mm) Diameter Conductive air hose inches / (mm) Hoses Length feet / (m) Kit part number 15 7 / (4.8 m) 0.27 / (7 mm) 24 6 / (7.5 m) / (4.8 m).027 / (7 mm) 24 6 / (7.5 m) PUMP KITS FOR AIRMIX Xcite SPRAY GUNS WITH SWIVEL FITTINGS Kit description Gun type Aircap Tip Wall-mounted Kit Portable Kit Portable kit with funnel Wall-mounted Kit Wall-mounted 20.15F Kit Xcite 120 Hose Length Suction rod Stainless steel Onepass heater Filter pump outlet Wall-mounted Kit VX 24 K To be ordered 24 6 HVLP separately (7.5 m) (see table) - Wall-mounted stainless steel 17.A2 Kit - Wall-mounted Kit Hot spraying wall-mounted Kit Xcite Kit part number Wall-mounted stainless steel 34A2 Kit Xcite

12 MVX GUN AIRMIX MVX Spray Guns The AIRMIX guns and is now the standard in the industry. It has superior ergonomic design and uses the highest quality components for long lasting reliable performance. Most importantly, it opens a whole new world to users by putting in the hands of an Airmix sprayer the ability to significantly vary the pattern without changing the tip while using minimal compressed air. Features Ergonomic design and light trigger Quick fan adjustment Handle swivel fitting Flexible air hose Product fluid passages in stainless steel New aircap and tip design SPECIFICATIONS Sprayed materials Polyurethanes, water-based products, high solids, twocomponents products, stains, lacquers, varnishes, etc... Body of the gun Forged aluminum Fluid Pressure Range psi / ( bar) Maximum air inlet pressure 90 psi / (6 bar) Recommended atomization air pressure psi / (0.8-3 bar) Fluid output (l/mn) Depends on the tip used Weight 20.1 oz / (575 g) Maximum Fluid Temperature 122 F / (50 C) Air consumption cfm / (5-7.5 m3/h) Wetted parts Stainless steel, PTFE Safety Trigger lock Filter (fitted on fluid tube) #6-85 mesh/ 168µ SWIVEL FITTINGS Fitting Air Inlet 6 x 8 (+ 6 x 8/F 1/4 NPS # air reg.) Fluid Inlet M 1/2" JIC STANDARD FITTINGS Benefits Less operator fatigue and improved productivity Ability to adjust the fan width to the shape of the part to be painted leads to higher efficiency and productivity User friendly Compatible with most coatings including waterbased, two components materials Outstanding spraying quality with reduced overspray Fitting Air Inlet M 1/4 NPS Fluid Inlet M 1/2" JIC CONFIGURATION OF THE AIRMIX MVX SPRAY GUNS WITH SWIVEL FLUID AND QUICK AIR FITTINGS Aircap Tip Maximum fluid Gun type pressure Seat Type size MVX psi / (60 bar) Polyacetal MVX 120 To be ordered separately (see table) 1800 psi / (120 bar) Stainless steel MVX psi / (200 bar) Carbide SEAL KITS Seal kit for MVX spray gun Repair kit for MVX spray gun (seal kit included) KITS FOR AIRMIX MVX SPRAY GUNS WITH SWIVEL FITTINGS Aircap Diameter Tip Type conductive fluid hose non conductive fluid hose Hose Length Kit part number MVX 60 VX 14 To be ordered 1.8 / (4.8 mm) 0.2 x 0.3 / (6 x 8 mm) 24 6 / (7.5 m) MVX 120 VX 14 separately 1.8 / (4.8 mm) 0.2 x 0.3 / (6 x 8 mm) 24 6 / (7.5 m) MVX 200 VX 14 (see table) 1.8 / (4.8 mm) 0.2 x 0.3 / (6 x 8 mm) 24 6 / (7.5 m)

13 Aircaps for AIRMIX spray guns AIRCAPS FOR MVX SPRAY GUNS (Ø 35 mm) VX14 VX54 For MVX spray guns Adjustable fan No Spraying quality Excellent Good Transfer efficiency Excellent Excellent Non-stick coating No AIRCAPS FOR MX SPRAY GUNS (Ø 40 mm) BX 16 BX 36 BX 56 (non stick) BX 86 For MX, MRX, SX or JX spray gun For MR spray gun Spraying quality Excellent Very good Good Very good AIRMIX tips # 134.5xx.xxx (replace the crosses by numbers read in the table) TABLE OF TIPS FOR SOLVENT-BASED MATERIALS Size TABLE OF TIPS FOR WATER-BASED MATERIALS Size Ø (mm) Ø (mm) Water output at 35 bar in l/mn Water output at 35 bar in l/mn Water output at 70 bar in l/min Water output at 70 bar in l/mn Marking on gun filter Marking on gun filter Marking on pump filter Marking on pump filter Min. (VX14 aircap) Min.(BX16 aircap) Max. (VX14 aircap) Max. (BX16 aircap) Min. (VX14 aircap) Min. (BX16 aircap) Max. (VX14 aircap) Max. (BX16 aircap) Theoretical fan width at 25 cm ou (1) (1) (1) ou (1) (1) (1) (1) ou (1) (1) (1) (1) ou 12 Number (1) (1) (1) (1) (1) engraved on ou 12 the tip (1) (1) (1) (1) (1) (1) (1) (1) Theoretical fan width at 25 cm ou (1) (1) ou 6 Number (1) (1) (1) (1) ou 8 engraved on (1) (1) (1) (1) ou 12 the tip (1) (1) (1) (1) (1) ou (1) (1) (1) (1) (1) Aircaps and tips for AIRMIX spray guns (1) Tips recommended for an optimum fan adjustment with a VX14 aircap 13

14 Accessories Accessories Gun fluid filter screen PART NUMBERS Stainless steel screen for filter Size (µ) Quantity N N N Manual gun covers manual gun covers Protective gun covers - pack of Adjusting needles valves For air adjustment. ADJUSTING NEEDLE VALVES Adjusting needle for MVX, MXLT (MF 1/4") spray guns Extensions for Airmix spray guns AIRMIX spray guns can be fitted with extensions in order to spray inaccessible areas. EXTENSIONS FOR MXLT SPRAY GUNS Length Straight extension 10 / (250 mm) Straight extension 15.7 / (400 mm) Extension, elbow / (250 mm) EXTENSIONS FOR MVX SPRAY GUNS Length Straight extension 10 / (250 mm) Straight extension 15.7 / (400 mm) Elbow extension (45 angle) 10 / (250 mm) Two gun manifold (Stainless Steel) To supply 2 guns with air and solvent-based paint including shut-off valves and an extra-port to fit a third gun. ADAPTOR TO FEED TWO OR THREE GUNS Two guns manifold for Airmix guns Stainless steel suction hose & rod assemblies Suction hoses & rods Inlet fitting 1 to 5 gallon suction hose & tube assembly EZMix gallon suction hoses & rod assembly gallon suction hoses & rod assembly gallon suction hoses & rod assembly gallon suction hoses & rod assembly

15 Hose sleeve PART NUMBERS Hose sleeve - 16 ft / (5m) Hose sleeve - 25 ft / (7.5m) Hose sleeve - 32 ft / (10m) Hose sleeve - 50 ft / (15m) Hose sleeve ft / (30m) Hose sleeve ft / (300m) Microscreens and tip seals for Airmix guns PART NUMBERS Tip size Microscreen (99 µ) (pack of 10) PTFE O-ring seals (pack of 10) (140 mesh) and above Aircap seals PACKS PART NUMBER Quantity Easy-adjust seals for MVX spray guns x Aircap ring seals for MVX spray guns x Aircap ring seals for MXLT spray guns x Accessories Tip Cleaning Needles PART NUMBERS Unclogging needles Nozzles Quantity Size 0.02 / ( mm) / (0.9 mm) Seats for spray guns SEATS FOR MVX SPRAY GUNS Type Quantity Polyacetal seats Stainless steel seats and seals Carbide seats and seals SEATS FOR MXLT SPRAY GUNS Type Quantity Polyacetal seats Stainless steel seats and seals Carbide seats and seals Seals for stainless steel and carbide seats SEALS FOR AIRMIX GUN SEATS Quantity Seals for stainless steel and carbide seats swivel Extensions for airmix spray guns MXLT Part Number MVX Part Number 90º Angle elbow extension - 7" (178 mm) º Angle elbow extension - 10" (254 mm) º Angle elbow extension - 16" (406 mm) º Angle elbow extension - 22" (559 mm) º Angle elbow extension - 28" (711 mm)

16 Accessories Accessories TEST aircap with GAUGES for hvlp spray gun compliance Fits Gun Series M22 E3 K HVLP aircap with test gauges M22 E5 K HVLP aircap with test gauges M21 or M21/2 H3 HVLP aircap with test gauges M21 or M21/2 H5 HVLP aircap with test gauges M21 or M21/2 VLP3 HVLP aircap with test gauges M21 or M21/2 VLP5 HVLP aircap with test gauges techni lub - PTFE Grease (1) 0.33 oz tube of Techni lub (1) 15.5 oz can of Techni lub siphon hose inlet manifolds Two-way suction manifold for PMP-150 pump (siphon hoses not included) Two-way suction manifold for pump (siphon hoses not included) Two-way S/S suction manifold for pump (siphon hoses not included) Three-way suction manifold for pump (siphon hoses not included) Three-way S/S suction manifold for pump (siphon hoses not included) AIRMIX FLUID PRESSURE REGULATORS Part Number Airmix fluid regulator, psi (10-70 bar) Airmix fluid regulator, psi ( bar) Airmix fluid regulator PH, psi ( bar) Airmix fluid regulator with gauge kit, psi (10-70 bar) Airmix fluid regulator with gauge kit, psi ( bar) Fluid filter and regulator kit with bracket, psi (10-70 bar) Fluid filter and regulator kit with bracket, psi ( bar) Airmix back pressure regulator, psi ( bar) S/S Circulation kit, c/w drain rod, fits inlet (for use with ) Fluid regulator bracket and screws Pump carts Part Number Single post cart (Used for and pumps) Two arm cart w/ wall plate (Used for all other pumps) Circulating kits Part Number Aluminum circulating kit Stainless Steel valve circulating kit (Back pressure regulator is used in place of circulation valve) Airmix back pressure regulator MVX Filter Bowl Part Number MVX Filter bowl, 1/4 NPS

17 Accessories 1/4" air hose assemblies, conductive Part Number 5 ft. long air hose with 1/4 F NPS fittings ft. long air hose with 1/4 F NPS fittings ft. long air hose with 1/4 F NPS fittings ft. long air hose with 1/4 F NPS fittings ft. long air hose with 1/4 F NPS fittings ft. long air hose with 1/4 F NPS fittings ft. long air hose with 1/4 F NPS fittings /16" AIRMIX CONDUCTIVE FLUID HOSE S/S Fittings Part Number Plated Fittings Part Number 10 ft. long fluid hose with #5 JIC fittings ft. long fluid hose with #5 JIC fittings ft. long fluid hose with #5 JIC fittings ft. long fluid hose with #5 JIC fittings ft. long fluid hose with #5 JIC fittings AND 55 GALLON DIRECT DRIVE AGITATORS Part Number G5-5 Gallon agitator with side-mount bracket G5-5 Gallon S/S agitator with cover and nylon blade G55-55 Gallon S/S agitator with cover and nylon blades Accessories agitator/elevator SYSTEM FOR 55 GALLON DRUMS Part Number M3R55E - Gear drive agitator w/elevator and S/S 55 gallon drum cover G55E - Direct drive agitator w/elevator and S/S 55 gallon drum cover PUmp lubricant Part Number Lubricant T (1/4L) for solvent-based paints Lubricant T (1 quart) for solvent-based paints Lubricant T (1 gallon) for solvent-based paints Lubricant P (1 quart) for polyurethanes Lubricant P (1 gallon) for polyurethanes Protective cream Part Number Protective cream - Pack of Protective cream - Pack of Protective cream - Pack of viscosity cup & wet film thickness gauge Part Number Viscosity cup number 4 (CA4) Wet film build thickness test gauge

18 Selection table - Airmix Pumps SELECTION TABLE Intensive AIRMIX pumps Type of pump Intensives TM Construction Stainless steel Mounting Wall-mounted Cart-mounted Portable Opt. Opt. For hot circulation Opt. Opt. Opt. Dimensions (wall-mounted pump without filter or suction rod) Height 16 / (410 mm) 16.9 / (430 mm) 32.3 / (820 mm) 33.1 / (840 mm) Width 11.4 / (292 mm) 9.4 / (240 mm) 13.8 / (350 mm) 18.5 / (470 mm) Depth 6.7 / (170 mm) 10.6 / (270 mm) 8.3 / (210 mm) 10.6 / (270 mm) Weight 12 lb / (5.,5 kg) 19.8 lb / (9 lb) 48 lb / (22 kg) 66 lb / (30 kg) Type of motor air / fluid section Air motor Stroke of motor 1.7 / (45 mm) 2.1 / (55 mm) 3.9 / (100 mm) 3.9 / (100 mm) Hydraulic section Characteristics Pressure ratio 10/1 20/1 20/1 20/1 Output per cycle (cc) 0.6 oz / (18 cc).74 oz / (22 cc) 1.69 oz / (50 cc) 3.38 oz / (100 oz) Number of cycles 14.5 gal / (55 per liter) 11.9 gal / (45 per liter) 5.3 gal / (20 per liter) 2.6 gal / (10 per liter) Output at 30 cycles/mn gal / (0.53 L).39 gal / (0.66 L) 0.39 gal / (1.5 L) 0.7p gal / (3 L) Free output per minute 37.2 oz / (1.1 L) 44.6 oz / (1.32 L) oz / (3 L) oz. / ( 6 L) Max. fluid pressure 900 psi / (60 bar) 1800 psi / (120 bar) 1800 psi / (120 bar) 1800 psi / (120 bar) Max. paint temperature 140 F / (60 C) 140 F / (60 C) 140 F / (60 C) 140 F / (60 C) Operating air pressure psi / (1-6 bar) psi / (1-6 bar) psi / (1-6 bar) psi / (1-6 bar) Max. air cons. at 30cycles/mn and 60 psi (4 bar) 1.1 cfm / (1.9 Nm 3 /h) (1) 2.8 cfm / (4.8 Nm 3 /h) (1) 6.3 cfm / (10.8 Nm 3 /h) ( cfm (21.6 Nm 3 /h) (1 (1) Air consumption (Nm 3 /h) = (1,2 x (output at 20 or 30 cycles in l/mn) x (compression ratio) x (air motor pressure + 1 bar) x 60) /

19 AIRMIX "START PUMP" This is the new entry level Airmix pump. It uses the same high efficiency and environmentally friendly technology that is found on the pump. This pump is ideal for small to hobbyist shops that can benefit from the power of Airmix. Features Small fluid section and suction rod The gun/pump kit works with a compressor of 1.5 HP Simple design, reduced number of spare parts Compact design SPECIFICATIONS Pressure ratio 10/1 Fluid volume per cycle (cm 3 ) 18 Number of cycles per liter of products 55 Fluid Output at 30 cycles/mn (l/mn) 0.53 Air consumption at 30 cycles/mn at 60 psi (4 bar) 1.1 cfm / (1.9 m 3 /h) Free flow rate (L/mn) 1.1 Maximum air inlet pressure 90 psi / (6 bar) Maximum fluid pressure 900 psi / (60 bar) Maximum Fluid Temperature 140 F / (60 C) Sound level (dba) 80 Sealing Packings Upper sealing Stainless steel cartridge with GT sealing Lower sealing PFA seals Weight (w/o support or rods) 11.7 lb / (5.30 kg) Wetted parts Stainless steel Height 15.5 / (40.5 cm) Width 12 / (30.5 cm) Depth 7 / (17.8 cm) FITTINGS Fitting Air inlet (valve) F 3/8" BSP Air outlet (atomization air) M 1/4" NPS Fluid Inlet M 18 x 125 Fluid Outlet M 1/2 JIC SEAL KITS Benefits Less product loss during color-changing and pump flushing Reduction of operational costs Easy maintenance Fits in small working areas Pump supplied with MVX gun and hoses (not shown on the photo) Seal kit for H Repair kit for H Repair kit for 340/2 air motor Intensive AIRMIX pump AIRMIX PUMP - "START" KIT with standard fitting MVX and 5 M air and fluid HOSES Set-up Aircap Type 10.14S VX 14 Tip Suction rod Drain rod To be ordered separately Air adjusting needle valve Fluid pressure air regulator Pump output filter

20 AIRMIX STAINLESS STEEL Feeding of one gun for intensive works. High efficiency and environmentally friendly technology. Ideal for wood, metal and plastics markets. Intensive TM AIRMIX pump Features Optimized fluid section and suction rod The gun/pump kit works with a compressor of 1.5 HP Simple design, reduced number of spare parts Compact design SPECIFICATIONS Pressure ratio 10/1 Fluid volume per cycle (cm 3 ) 18 Number of cycles per liter of products 55 Fluid Output at 30 cycles/mn (l/mn) 0.53 Air consumption at 30 cycles/mn at 60 psi (4 bar) 1.1 cfm / (1.9 m 3 /h) Free flow rate 0.29 gal/mn (1.1 L/mn) Maximum air inlet pressure 900 psi / (60 bar) Maximum fluid pressure 900 psi / (60 bar) Maximum Fluid Temperature 140 F / (60 C) Sound level (dba) 80 Sealing Packings Upper sealing Stainless steel cartridge with GT sealing Lower sealing PFA seals Weight 12 lb / (5.45 kg) (w/o support or rods) (wall mounted without rod) Wetted parts Stainless steel Height 16 / (40.5 cm) Width 12 / (30.5 cm) Depth 7 / (17.8 cm) FITTINGS Fitting Air inlet (valve) F 3/8" BSP Air outlet (atomization air) M 1/4" NPS Fluid Inlet M 18 x 125 Fluid Outlet M 1/2 JIC CONFIGURATION OF THE AIRMIX PUMP - STAINLESS STEEL Set-up Suction rod Drain rod Atomization air regulator Fluid pressure air regulator Filter pump outlet Wall mounted On one-arm cart Portable (1) (1) Option : 2 liters gravity funnel and support : Benefits Less product loss during color-changing and pump flushing Reduction of operational costs Easy maintenance Fits in small working areas Portable version SEAL KITS Seal kit for H repair kit for H Repair kit for 340/2 air motor AIRMIX PUMP KITS with swivel fitting MVX Kit description wallmounted wallmounted wallmounted Gun type Aircap Type MVX 60 VX 14 MVX 60 VX 14 MVX 60 VX 14 Tip To be ordered separately To be ordered separately To be ordered separately Suction rod Hoses Length Pump output filter Funnel 24 6 / (7.5 m) / (7.5 m) / (7.5 m)

21 AIRMIX PUMP - STAINLESS STEEL A multi-purpose, very quiet pump designed to deliver thicker coatings (up to 9000 cps) to a single spray gun in either wood, metal, or plastic finishing applications. Features Benefits All stainless steel construction Compatible with water-based materials Large diameter suction rod and high compression ratio Use with a large number of materials The gun/pump kits work with a compressor of 2 HP Reduction of operational costs Simple design, reduced number of spare parts Easy maintenance Compact design Fits in small working areas SPECIFICATIONS Pressure ratio 20/1 Fluid volume per cycle (cm 3 ) 22 Number of cycles per liter of products 45 Fluid Output at 30 cycles/mn (l/mn) 0.66 Free flow rate (L/mn) 0.34 gal/mn / (1.32 L/mn) Air consumption at 30 cycles/mn at 4 bar 2.8 cfm / (4.8 m 3 /h) Maximum air inlet pressure 90 psi / (6 bar) Maximum fluid pressure 1,800 psi / (120 bar) Maximum Fluid Temperature 140 F / (60 C) Sound level (dba) 82 Sealing Packings Upper sealing GT cartridge with polyethylene packing Lower sealing PFA sealing Weight - wall-mounted pump w/o rods 19.8 lb / (9 kg) Wetted parts Stainless steel Height 18 / (45.7 cm) Width 14 / (35.6 cm) Depth 8 / (20.3 cm) FITTINGS Fitting Air inlet (valve) F 3/8 BSP Air outlet (atomization air) M 1/4 NPS Fluid Inlet M 26 x 125 Fluid Outlet M 1/2 JIC CONFIGURATION OF THE AIRMIX PUMPS Set-up Suction rod Drain rod 6L FUNNEL Atomization air regulator Fluid pressure air regulator Pump output filter (with 6 L funnel as an option) Wall mounted Wall mounted On one arm cart Portable Designation 6l funnel (26x125 inlet) - for mounting on one-arm cart Intensive AIRMIX pump SEAL KITS H15 Seal kit H15 Maintenance kit H15 Rebuilding kit Repair kit for air motor KIT FOR AIRMIX PUMPS with swivel fitting MVX Kit description Gun type Aircap Type Stainless steel One-pass heater wall-mounted MVX 120 VX hot spraying wall-mounted MVX 120 VX14 Tip To be ordered separately To be ordered separately Suction rod Hoses Length Filter 24 6 / (7.5 m) / (7.5 m)

22 AIRMIX PUMP - STAINLESS STEEL Ideal for feeding one or two Airmix spray guns or one gun in a heated circulation loop for small to medium production shop, the can pump a variety of coatings. The pump comes with the pump regulator, atomization regulator, and filter. Intensive AIRMIX pump Features Benefits Large diameter suction rod and high compression ratio Use with a large number of materials All stainless steel construction Compatible with water-based materials Simple design, reduced number of spare parts Easy maintenance SPECIFICATIONS Pressure ratio 20/1 Fluid volume per cycle (cm 3 ) 50 Number of cycles per liter of products 20 Fluid Output at 30 cycles/mn (l/mn) 1.5 Free flow rate (L/mn) 0.79 gal/mn / (3 L/mn) Air consumption at 30 cycles/mn at 60 psi (4 bar) 6.3 cfm / (10.8 m 3 /h) Maximum air inlet pressure 90 psi / (6 bar) Maximum fluid pressure 1800psi / (120 bar) Maximum Fluid Temperature 140 F / (60 C) Sound level (dba) 78 Sealing Packings Upper sealing Polyfluid + PTFE G Lower sealing GT sealing Weight 37.5 lb / (17 kg) Wetted parts Stainless steel Height 33 / (83.8 cm) Width 14 / (35.6 cm) Depth 7 / (17.8 cm) FITTINGS Fitting Air inlet (valve) F 3/8" BSP Air outlet (atomization air) M 1/4" NPS Fluid Inlet M 26 x 125 Fluid output (filter) M 1/2" JIC CONFIGURATION OF AIRMIX PUMPS Set-up Suction rod Drain rod SEAL KITS Atomization air regulator Fluid pressure air regulator Pump output filter Model shown on a two-arm cart Wall mounted Wall mounted arm cart-mounted H25 GT seal kit H25 GT repair kit Seal kit for air motor Repair kit for air motor KITS FOR AIRMIX PUMPS with swivel fitting MVX Kit designation Gun type Wall-mounted MVX Wall-mounted Hot spraying MVX 120 Aircap Type VX14 Tip Heater Hoses Length Pump output filter To be ordered separately - (AD60) 24 6 / (7.5 m)

23 AIRMIX PUMP - STAINLESS STEEL The pump is ideal for large production shops where medium to heavy bodied materials will be fed to multiple guns from one fluid supply. Features Benefits Simple design, reduced number of spare parts Easy maintenance Large diameter suction rod and high compression ratio Use with a large number of materials All stainless steel construction Compatible with water-based products SPECIFICATIONS Pressure ratio 20/1 Fluid volume per cycle (cm 3 ) 100 Number of cycles per liter of products 10 Fluid Output at 30 cycles/mn (l/mn) 0.79 gal/mn / (3 L/mn) Free flow rate (L/mn) 1.58 gal/mn / (6 L/mn) Air consumption at 30 cycles/mn at 60 psi (4 bar) 12.7 cfm / (21.6 m 3 /h) Maximum air inlet pressure 90 psi / (6 bar) Maximum fluid pressure 1800psi / (120 bar) Maximum Fluid Temperature 140 F / (60 C) Sound level (dba) 78 Sealing Packings Upper sealing Polyfluid + PTFE G Lower sealing GT Weight 22 Wetted parts Stainless steel Height 34 / (86.4 cm) Width 14 / (35.6 cm) Depth 11 / (28 cm) FITTINGS Fitting Air inlet (valve) F 3/8" BSP Air outlet (atomization air) M 1/4" NPS Fluid Inlet M 26 x 125 Fluid output (filter) M 1/2" JIC CONFIGURATION OF AIRMIX PUMPS Set-up Suction rod Drain rod Atomization air regulator Fluid pressure air regulator Pump output filter Wall mounted Wall mounted On one-arm cart SEAL KITS H50 GT seal kit H50 GT repair kit Seal kit for air motor Repair kit for air motor Intensive AIRMIX pump 23

24 SELECTION TABLE - FLOWMAX PUMPS Flowmax pumps Exclusive precisely machined SuperLife Bellows replaces the traditional leaky packings Delivers a wide range of pressures without the use of fluid regulators The fluid inlet is located on the upper end of the fluid section making the pump easier to service Contains single lip seals with automatic wear take-up for high up-time and minimal maintenance Unique SuperQuiet air motor changeover with very high and reliable performance All stainless steel fluid sections suitable for a wide variety of fluids Easy access to wearing parts due to a tie rod free design The exclusive Flowmax SuperLife Technology is available only with Kremlin. Nothing of similar pressure and fluid output in the piston pump design outperforms the Flowmax SuperLife technology. Flowmax pumps substantially outlast standard piston pumps using self-adjusting seals. In addition there is no lubricant cup, thus eliminating packings. In sum, this is a packing-free pump that performs quietly with minimal service. Nothing compares to the Power of Airmix! SELECTION TABLE Pump type Construction Flowmax Bellow SuperLife TM 17.A F F F Stainless steel Configuration Wall-mounted Cart-mounted Opt. Dimensions (wall-mounted pump without filter or suction rod) Height 24.5 / (622 mm) 22.4 / (570 mm) 38.2 / (970 mm) 382 / ( 975 mm) Width 13 / (330 mm) 13.4 / (240 mm) 13.8 / (350 mm) 18.5 / (470 mm) Depth 8.3 / (211 mm) 11.2 / (285 mm) 8.3 / (210 mm) 10.6 / (270 mm) Weight 44.1 lb / (20 kg) 25.4 lb / (11.5 kg) 66.1 lb / (30 kg) 77.2 lb / (35 kg) Air motor/fluid section Air motor Stroke of air motor 1.9 / (50 mm) 2.2 / (55 mm) 3.9 / (100 mm) 3.9 / (100 mm) Fluid section 30 S 15 F 25 F 50 F Specifications Pressure ratio 17/1 20/1 20/1 20/1 Output per cycles 2.02 oz / (60 cc) 0.74 oz / (22 cc) 1.69 oz / (50 cc) 3.38 oz / (100 cc) Number of cycles (per gallon / per liter) 4.22 gal / (16 L) gal / (45 L) 5.28 gal / (20 L) 2.64 gal / (10 L) Output at 30 cycles/mn..47 gal / (1.8 L) 0.17 gal / (0.66 L) 0.39 gal / (1.5 L) 0.79 gal / (3 L) Free output per minute.95 gal / (3.6 L).34 gal / (1.32 L).79 gal / (3 L) 1.6 gal / (6 L) Max. fluid pressure 1530 psi / (102 bar) 900 psi / (60 bar) 1800 psi / (120 bar) 1800 psi / (120 bar) Max. paint temperature 122 F / (50 C) 122 F / (50 C) 122 F / (50 C) 122 F / (50 C) Operating air pressure psi / (1-6 bar) psi / (2-6 bar) psi / (1-6 bar) psi / (1-6 bar) Max. air consumption at 30 cycles/mn under 4 bar (Nm3/h) (1) 6.47 cfm / (11 Nm 3 /h) 2.8 cfm / (4.8 Nm 3 /h) 6.4 cfm / (10.8 Nm 3 /h) 12.7 cfm / (21.6 Nm 3 /h) (1) Air consumption (Nm 3 /h) = (1,2 x (output at 20 or 30 cycles in l/mn) x (compression ratio) x (air motor pressure + 1 bar) x 60) /

25 SELECTION TABLE FLOWMAX PUMPS Pump Type 34.A F F Construction Stainless steel Configuration Wall-mounted Cart-mounted Dimensions (wall-mounted pump without filter or rod) Height 24 / (610 mm) 38 / (970 mm) 38 / (970 mm) Width 16 / (410 mm) 15.8 / (400 mm) 15.8 / (400 mm) Depth 9.8 / (250 mm) 11 / (280 mm) 11 / (280 mm) Weight 59.5 lb / (27 kg) 81.6 lb / (37 kg) 92.6 lb / (42 kg) Air motor/fluid section Air motor Stroke of air motor 1.9 / (50 mm) 3.9 / (100 mm) 3.9 / (100 mm) Fluid section F 50 F Characteristics Pressure ratio 34/1 40/1 40/1 Flowmax pumps Output per cycle 2.02 oz / (60 cc) 1.69 oz / (50 cc) 3.38 oz / (100 cc) Number of cycles (per gal / per liter) 4.22 gal / (16 liter) 5.28 gal / (20 liter) 2.64 gal / (10 liter) Output at 30 cycles/mn.478 gal / (1.8 L) 0.39 gal / (1.5 L) 0.79 gal / ( 3 L) Free output per minute.95 gal / (3.6 L) 0.79 gal / (3 L) 1.58 gal / (6 L) Max. product pressure 3000 psi / (200 bar) 3600 psi / (240 bar) 3600 psi / (240 bar) Max. paint temperature 122 F / (50 C) 122 F / (50 C) 122 F / (50 C) Operating air pressure psi / (1-6 bar) psi / (1-6 bar) psi / (1-6 bar) Max. air consumption (1) 12.9 cfm / (22 m 3 /h) 12.7 cfm / (21.6 m 3 /h) 25.4 fm / 43.2 m 3 /h) (1) Air consumption (Nm 3 /h) = (1,2 x (output at 20 or 30 cycles in l/mn) x (compression ratio) x (air motor pressure + 1 bar) x 60) /

26 FLOWMAX 17.A2 PUMP - STAINLESS STEEL Flowmax 17.A2 pump Unique design with external valves for an easy maintenance. Flowmax technology ensures total sealing. Quick inversion of this pump allows for a perfectly stable fan shape at the gun. Performance, extended lifetime, reliability. Features External valves assembly Floating piston Sealing ensured by a Superlife TM bellow seal All stainless steel construction Large and smooth fluid passages Balanced fluid section SPECIFICATIONS Benefits Easy maintenance Fast inversions and very high efficiency High reliability No more lubricant cups Leak free Total sealing between pump and its environment, ideal to work with isocyanates catalysts Compatible with UV and pre-catalyzed products Compatible with water-based materials Fluid discharge without retention of a wide range of coating materials Constant fluid output pressure Pressure ratio 17/1 Fluid volume per cycle (cm 3 ) 60 Number of cycles per liter of products 16 Fluid Output at 30 cycles/mn (l/mn) 1.8 Free flow rate (L/mn) 0.95 Gal/mn / (3.6 L/mn) Air consumption at 30 cycles/mn at 60 psi (4 bar) 6.5 cfm / (11 m 3 /h) Maximum air inlet pressure 90 psi / (6 bar) Maximum fluid pressure 1500 psi / (100 bar) Maximum Fluid Temperature 122 F / (50 C) Sound level (dba) 74 Sealing packing Bellows Polyethylene Upper and lower GT polyethylene Weight - wall-mounted 44 lb / (20 kg) Wetted parts Stainless steel Height 24.5 / (62.2 cm) Width 13 / (33 cm) Depth 8.3 / (21 cm) FITTINGS Fitting Air inlet (valve) F 3/8" BSP Air outlet (atomization air) M 1/4" NPS Fluid Inlet M 26 x 125 Fluid output (filter) M 1/2 JIC CONFIGURATION OF THE FLOWMAX AIRMIX 17.A2 PUMP Set-up Suction rod Drain rod Wall-mounted 17.A2 Flowmax pump 1 arm cart 17.A2 Flowmax pump Atomization air regulator Fluid pressure air regulator Pump output filter SEAL KITS Seal kit for A2 fluid section Repair kit for A2 fluid section Seal kit for external valves Seal kit for air motor Repair kit for air motor KITS FOR FLOWMAX AIRMIX 17.A2 PUMPS with swivel fitting MVX Kit designation Gun type Tip Flowmax 17.A2 Wall-mounted MVX 120 To be ordered separately Supplied with aircap Suction rod Hoses Length Filter VX / (7.5 m)

27 FLOWMAX 20.15F PUMP - STAINLESS STEEL The new generation of AIRMIX pump, benefiting of the Flowmax technology. Designed for fluid to semi-fluid materials. Features Benefits Sealing done by one bellow High reliability Total sealing between pump and its environment, ideal to work with isocyanates catalysts No fluid leakages Ideal for UV and pre-catalyzed materials No lubricant needed Stainless steel design Compatible with water-based materials Large diameter suction rod and high compression ratio Use with a large number of materials The gun/pump kits work with a compressor of 2 HP Reduction of operational costs Simple design, reduced number of spare parts Easy maintenance Compact design Fits in small working areas SPECIFICATIONS Pressure ratio 20/1 Fluid volume per cycle (cm 3 ) 22 Number of cycles per liter of products 45 Fluid Output at 30 cycles/mn (l/mn) 0.66 Free flow rate (L/mn) 0.34 Gal/mn / ( 1.32 L/mn) Air consumption at 30 cycles/mn at 60 psi (4 bar) 2.8 cfm / (4.8 m 3 /h) Maximum air inlet pressure 90 psi / (6 bar) Maximum fluid pressure 1800 psi / (120 bar) Maximum Fluid Temperature 122 F / (50 C) Sound level (dba) 80 Sealing packing Bellows Polyethylene Upper and lower GT cartridge with polyethylene packing. PFA seal. Weight - wall-mounted pump w/o rods 25.3 lb / (11.5 kg) Wetted parts Hard chrome stainless steel, stainless steel Height 22.4 lb / (57 cm) Width 9.4 / (24 cm) Depth 11.2 / (28.5 cm) Flowmax 20.15F pump FITTINGS Fitting Air inlet (valve) F 3/8" BSP Air outlet (atomization air) M 1/4" NPS Fluid Inlet M 18 x 125 Fluid Outlet M 1/2 JIC CONFIGURATION OF THE AIRMIX F PUMPS Set-up Suction rod Drain rod Atomization air regulator Fluid pressure air regulator Filter pump outlet Wall-mounted Wall-mounted On one arm cart (1) L FUNNEL Designation 6l funnel (18x125 inlet) - for mounting on 1 arm cart SEAL KITS Seal kit H15F Repair kit H15F Repair kit for air motor (1) As an option : 6 liter funnel KIT FOR AIRMIX 20.15F PUMPS with swivel fitting MVX Aircap Kit designation Gun type Tip Suction rod Hoses Length Filter Funnel Type 20.15F Wall-mounted MVX 120 VX 14 To be ordered separately 24 6 / (7.5 m)

28 FLOWMAX 20.25F PUMP - STAINLESS STEEL Universal AIRMIX pump for use with all materials, including water-based and high solids. Flowmax 20.25F pump Features Sealing done by one large stroke bellow Ergonomic design of fluid passages All stainless steel construction Balanced fluid section Mobile piston seal SPECIFICATIONS Benefits High reliability No more lubricant cups No fluid leakages Total sealing between pump and its environment, ideal to work with isocyanates catalysts Ideal for UV and pre-catalyzed materials Fluid discharge without retention of a wide range of coating materials Compatible with water-based materials Constant fluid output pressure Excellent suction capacity Pressure ratio 20/1 Fluid volume per cycle (cm 3 ) 50 Number of cycles per liter of products 20 Fluid Output at 30 cycles/mn 0.39 Gal / (1.5 L) Free flow rate 0.79 Gal / (3 L) Air consumption at 30 cycles/mn at 60 psi (4 bar) 6.5 cfm / (10.8 m3/h) Maximum air inlet pressure 90 psi / (6 bar) Maximum fluid pressure 1800 psi / (120 bar) Maximum Fluid Temperature 122 F / (50 C) Sound level (dba) 80 Sealing packing Bellows Polyethylene Upper and lower GT Polyethylene Weight - wall-mounted 48.5 lb / (22 kg) Wetted parts Stainless steel Height 39 / (99,1 cm) Width 19 / (48.3 cm) Depth 11 / (28 cm) FITTINGS Fitting Air inlet (valve) F 3/8" BSP Air outlet (atomization air) M 1/4" NPS Fluid Inlet M 26 x 125 Fluid output (filter) M 1/2" JIC CONFIGURATION OF THE FLOWMAX AIRMIX 20.25F - STAINLESS STEEL Set-up Suction rod Drain rod Atomization air regulator Fluid pressure air regulator Pump output filter Wall mounted Wall mounted arms Cartmounted SEAL KITS Seal kit H25F Repair kit H25F Seal kit for air motor Repair kit for air motor KIT FOR FLOWMAX AIRMIX F PUMPS with swivel fitting MVX Kit designation F wallmounted Gun type Supplied with aircap MVX 120 VX 14 Tip Suction rod Hose Length Filter To be ordered separately 24 6 / (7.5 m)

29 FLOWMAX 20.50F PUMP - STAINLESS STEEL Universal AIRMIX pump for use with all materials, including water-based and high solids. Features Sealing done by one large stroke bellow Ergonomic design of fluid passages All stainless steel construction Balanced fluid section Mobile piston seal SPECIFICATIONS Benefits High reliability No more lubricant cups No fluid leakages Total sealing between pump and its environment, ideal to work with isocyanates catalysts Ideal for UV and pre-catalyzed materials Fluid discharge without retention of a wide range of coating materials Compatible with water-based materials Constant fluid output pressure Excellent suction capacity Pressure ratio 20/1 Fluid volume per cycle (cm 3 ) 100 Number of cycles per liter of products 10 Fluid Output at 30 cycles/mn 0.79 Gal / (3 L) Free flow rate 1.58 Gal/mn / (6 L/mn) Air consumption at 30 cycles/mn at 60 psi (4 bar) 12.7 cfm / (21.6 m 3 /h) Maximum air inlet pressure 90 psi / (6 bar) Maximum fluid pressure 1800 psi / (120 bar) Maximum fluid Temperature 122 F / (50 C) Sound level (dba) 76 Sealing packing Bellows Polyethylene Upper and lower GT Polyethylene Weight - wall-mounted 59.5 lb / (27 kg) Wetted parts Stainless steel Height 38.4 / (97.5 cm) Width 18.5 / (47 cm) Depth 10.6 / (27 cm) FITTINGS Fitting Air inlet (valve) F 3/8" BSP Air outlet (atomization air) M 1/4" NPS Fluid Inlet M 26 x 125 Fluid output (filter) M 1/2" JIC CONFIGURATION OF THE FLOWMAX AIRMIX 20.50F - STAINLESS STEEL Model shown : F Set-up Suction rod Drain rod Atomization air regulator Fluid pressure air regulator Pump output filter Wall mounted Wall mounted arms Cartmounted SEALS KITS Seal kit H 50F Repair kit H 50F Seal kit for air motor Repair kit for air motor Flowmax 20.50F pump

30 FLOWMAX 34.A2 PUMP Unique design with external valves for an easy maintenance. Flowmax technology ensures total sealing. Quick inversion of this pump allows for a perfectly stable fan shape at the gun. Performance, extended lifetime, reliability. Flowmax 34.A2 pump Features External valves assemby Floating piston Sealing done by one bellow Large and smooth fluid passages All stainless steel construction Balanced fluid section SPECIFICATIONS Pressure ratio 34/1 Fluid volume per cycle (cm3) 60 Number of cycles per liter of products 16 Fluid Output at 30 cycles/mn 0.47 Gal/mn / (1.8 L/mn) Air consumption at 30 cycles/mn at 60 psi (4 bar) 12.9 cfm / (22 m3/h) Free flow rate 0.92 Gla/mn / (3.6L/mn) Maximum air inlet pressure 90 psi / (6 bar) Maximum fluid pressure 3000 psi / (200 bar) Maximum Fluid Temperature 122 F / (50 C) Sound level (dba) 71 Sealing packing Bellows Polyethylene Upper and lower GT Polyethylene Wetted parts Stainless steel Weight (kg) - wall-mounted 58.4 lb / (26.5 kg) Height (cm) 24 / (61 cm) Width (cm) 16.1 / (41 cm) Depth (cm) 9.8 / (25 cm) FITTINGS Benefits Easy maintenance Fast inversions and very high efficiency High reliability No more lubricant cups No fluid leakages Total sealing between pump and its environment, ideal to work with isocyanates catalysts Ideal for UV and pre-catalyzed materials Fluid discharge without retention of a wide range of coating materials Compatible with water-based materials Constant fluid output pressure Fitting Air inlet (valve) F 3/4" BSP Air outlet (option atomization air kit) M 1/4" NPS Fluid Inlet M 26 x 125 Fluid output (filter) M 1/2 JIC CONFIGURATION OF THE FLOWMAX 34.A2 PUMP Set-up Suction rod Drain rod Wall-mounted Flowmax 34.A2 1 arm cart Flowmax 34.A2 Fluid pressure air regulator Pump output filter ATOMIZATION AIR KIT WITH REGULATOR Atomization air kit with regulator (for MVX200 spray guns) SEAL KITS Seal kit for A2 fluid section Repair kit for A2 fluid section Seal kit for external valves Seal kit for air motor Repair kit for air motor KITS FOR FLOWMAX 34.A2 PUMPS with swivel fitting GUNS Kit designation Gun type Suction rod Wall-mounted Flowmax 34.A2 Wall-mounted Flowmax 34.A2 Atomization air regulator Hoses Length Pump output filter Kit part number M / (10 m) MVX 200, VX14 aircap 24 6 / (7.5 m)

31 40.25 PUMP - STAINLESS STEEL Ideal for outputs up to 1.5 liter/mn Features Benefits Large diameter suction rod and high compression ratio Use with a large number of materials All stainless steel construction Compatible with water-based products Simple design, reduced number of spare parts Easy maintenance SPECIFICATIONS Pressure ratio 40/1 Fluid volume per cycle (cm ) 50 Number of cycles per liter of products 20 Fluid Output at 30 cycles/mn 0.39 Gal / (1.5 L) Air consumption at 30 cycles/mn at 60 psi (4 bar) 12.7 cfm / (21.6 m 3 /h) Free flow rate 0.79 Gal /mn / (3 L/mn) Maximum air inlet pressure 90 psi / (6 bar) Maximum fluid pressure 3600 psi / (240 bar) Maximum Fluid Temperature 140 F / (60 C) Sound level (dba) 77 Sealing Packings Upper sealing Polyfluid + PTFE G Lower sealing GT seal Wetted parts Stainless steel Weight - wall-mounted 48.5 lb / (22 kg) Height 31.5 / (80 cm) Width 15.7 / (40 cm) Depth 11 / (28 cm) FITTINGS Fitting Air inlet (valve) F 3/4" BSP Air outlet (option atomization air kit) M 1/4" NPS Fluid Inlet M 26x125 Fluid output (filter) M 1/2" JIC CONFIGURATION OF THE AIRLESS PUMP -STAINLESS STEEL Set-up Suction rod Drain rod Fluid pressure air regulator Pump output filter Wall mounted Wall mounted arms cart mounted ATOMIZATION AIR KIT WITH REGULATOR Atomization air kit with regulator (for MVX200 spray guns) SEAL KITS H25 GT seal kit H25 GT repair kit Seal kit for air motor Repair kit for air motor Intensive pump stainless steel KITS FOR AIRLESS PUMPS with swivel fitting GUNS Kit designation Gun type Heater Suction rod Atomization air regulator Hoses Length Pump output filter Kit part number wall-mounted MVX 200, tête VX / (7.5 m) wall mounted M350, with 517 reversible tip / (10 m)

32 FLOWMAX 40.25F PUMP - STAINLESS STEEL Flowmax 40.25F pump stainless steel New generation Flowmax pump for low volume applications Features Sealing done by one large stroke bellow Ergonomic design of fluid passages All stainless steel construction Balanced fluid section Mobile piston seal SPECIFICATIONS Pressure ratio 40/1 Fluid volume per cycle (cm3) 50 Number of cycles per liter of products 20 Air consumption at 30 cycles/mn at 4 bar 12.7 cfm / (21.6 m3/h) Fluid Output at 30 cycles/mn 0.39 Gal/mn / (1.5 L/mn) Free flow rate 45 psi / (3 bar) Maximum fluid pressure 3600 psi / (240 bar) Maximum fluid temperature 122 F / (50 C) Maximum air inlet pressure 6 Sound level (dba) 72 Sealing packing Bellows Polyethylene Upper and lower GT polyethylene Wetted parts stainless steel Weight - wall-mounted 81.5 lb / (37 kg) Height 38 / (97 cm) Width 15.7 / (40 cm) Depth 11 / (28 cm) FITTINGS Fitting Air inlet (valve) F 3/4" BSP Air outlet (option atomization air kit) M1/4" NPS Fluid Inlet M 26 x 125 Fluid Outlet M 1/2" JIC CONFIGURATION OF THE FLOWMAX 40.25F PUMP - STAINLESS STEEL Set-up Suction rod Drain rod Fluid pressure air regulator Pump output filter Wall mounted Wall mounted Cart mounted ATOMIZATION AIR KIT Atomization air kit with regulator (for MVX200 spray guns) SEAL KITS Benefits High reliability No more lubricant cups No fluid leakages Total sealing - ideal for isocyanates Ideal for UV and pre-catalyzed materials Fluid discharge without retention of a wide range of coating materials Compatible with water-based materials Constant fluid output pressure Excellent suction capacity Kit part number Seal kit H25F Repair kit H25F Seal kit for air motor Repair kit for air motor PUMP KITS FOR FLOWMAX 40.25F with swivel fitting GUNS Kit designation Gun type Suction rod Atomization air regulator Hoses Length Pump output filter 40.25F Wall-mounted MVX 200, VX14 aircap 24 6 / (7.5 m) F Wall-mounted M / (10 m)

33 40.50 PUMP - STAINLESS STEEL Ideal for feeding two guns Features Simple design, reduced number of spare parts Large diameter suction rod and high compression ratio SPECIFICATIONS Pressure ratio 40/1 Fluid volume per cycle 100 cm 3 Number of cycles per liter of products 10 Fluid Output at 30 cycles/mn 0.79 Gal / (3 L) Free flow rate 1.58 Gal/mn / (6 L/mn) Air consumption at 30 cycles/mn at 60 psi / (4 bar) 24.4 cfm / (43.2 m3/h) Maximum air inlet pressure 90 psi / (6 bar) Maximum fluid pressure 3600 psi / (240 bar) Maximum Fluid Temperature 140 F / (60 C) Sound level (dba) 80 Sealing Packings Upper sealing Polyfluid + PTFE G Lower sealing GT sealing Wetted parts Stainless steel Weight - wall-mounted 48.5 lbs / (22 kg) Height 31.5 / (80 cm) Width 15.7 / (40 cm) Depth 11 / (28 cm) FITTINGS Benefits Easy maintenance Use with a large number of materials Fitting Air inlet (valve) F 3/4" BSP Air outlet (option atomization air kit) M 1/4" NPS Fluid Inlet M 26 x 125 Fluid output (filter) M 1/2" JIC CONFIGURATION OF THE AIRLESS PUMP - STAINLESS STEEL Set-up Suction rod Drain rod Fluid pressure air regulator Pump output filter Wall mounted Wall mounted Two arms cart-mounted pump stainless steel ATOMIZATION AIR KIT WITH REGULATOR Atomization air kit with regulator (for MVX200 spray guns) SEAL KITS H50 GT seal kit H50 GT repair kit Seal kit for air motor Repair kit for air motor

34 FLOWMAX 40.50F PUMP - STAINLESS STEEL Flowmax 40.50F pump New generation Flowmax pump, ideal for feeding two guns Features Sealing done by one large stroke bellow Ergonomic design of fluid passages All stainless steel construction Balanced fluid section Mobile piston seal SPECIFICATIONS Benefits High reliability No more lubricant cups No fluid leakages Total sealing between pump and its environment, ideal to work with isocyanates catalysts Ideal for UV and pre-catalyzed materials Fluid discharge without retention of a wide range of coating materials Compatible with water-based materials Constant fluid output pressure Excellent suction capacity Pressure ratio 40/1 Fluid volume per cycle (cm3) 100 Number of cycles per liter of products 10 Fluid Output at 30 cycles/mn 0.79 gal/mn / (3 L/mn) Air consumption at 30 cycles/mn at 60 psi / (4 bar) 25.4 cfm / (43.2 m3/h) Free flow rate 1.58 gal/mn / (6 L/mn) Maximum fluid pressure 3600 psi / (240 bar) Maximum fluid temperature 122 F / (50 C) Maximum air inlet pressure 90 psi / (6 bar) Sound level (dba) 77 Sealing packing Bellows Polyethylene Upper and lower GT Polyethylene Wetted parts Stainless steel Weight - wall-mounted 92.6 lb / (42 kg) Height 38 / (97 cm) Width 15.7 / (40 cm) Depth 11 / (28 cm) FITTINGS Fitting Air inlet (valve) F 3/4" BSP Air outlet (option atomization air kit) M 1/4" NPS Fluid Inlet M 26x125 Fluid Outlet M 1/2" JIC CONFIGURATION OF THE FLOWMAX 40.50F PUMPS- STAINLESS STEEL Set-up Suction rod Drain rod Fluid pressure air regulator Pump output filter Wall-mounted Wall-mounted Cart-mounted (on a 2-arms cart) ATOMIZATION AIR KIT Atomization air kit with regulator (for MVX200 spray guns) SEALS KITS Seal kit H 50F Repair kit H 50F Seal kit for air motor Repair kit for air motor

35 Recommendations to optimize your flowmax applications AREAS OF COMPETENCE OF THE FLOWMAX PUMPS INTENSIVE TM pumps FLOWMAX pump Frequent color changes - 2K materials (manual or booster pump) - Pre-catalyzed materials - Circulating/circulation - High volume applications - Charged materials - Max. product temperature 140 F / (60 C) 122 F / (50 C) Recommendations for airmix filtration To avoid any tip unplugging, it is necessary to opt for filtration by stages. RECOMMENDATIONS FOR AIRMIX PUMPS FILTRATION Strainer Pump Pump filter Gun filter Tip filter Tip size Ø suction tube filtration ,5 Micro screen microns Optional O' ring seal Micro screen / / F/20.50F/17.A microns 'O' ring seal Recommendations and Advice

36 AD 60/61 HEATERS : NON-EXPLOSIVE Original design ensuring optimum heat transfer with no risk of burning the paint in the heater. Heaters To be used in zone 1 and 2 according to ATEX. Features Available in stainless steel version A thermometer is integrated into the command box Modular design Agreement INERIS 03ATEX 0079X Ex II 2 G - EEx d II AT3 Benefits Compatible with water-based materials No pressure loss when working with high viscosity materials Easy maintenance SPECIFICATIONS Thermostat type By fluid extension and dry contact Thermal fuse Cut at F / (121 C) Thermometer Graduation F / (0-100 C) Temperature range F / (15-80 C) Pressure maximum 3600 psi / (240 bar) Weight Aluminum : 34.2 lb / (15.5 kg) Stainless steel : 55.1 lb / (25 kg) Wetted parts Aluminum : aluminum body, galvanized chrome fittings Stainless steel : stainless steel body and fittings Room temperature maximum 104 F / (40 C) AD HEATERS - ALUMINUM VERSION (SOLVENT BASE MATERIALS) Aluminum heater Voltage / Power Temperature Cable length Fitting Volt Watt w/o plug Inlet Outlet AD F (15-80 C) / (10 m) M 1/2 JIC M 1/2 JIC AD F (15-80 C) 16 5 / (5 m) M 1/2 JIC M 1/2 JIC AD HEATERS - STAINLESS STEEL VERSIONS Stainless steel Voltage / Power Temperature ( C) Cable length Fitting heater w/o plug Volt Watt Inlet Outlet AD / (10 m M 1/2 JIC M 1/2 JIC AD F (15-80 C) 16 5 / (5 m) M 1/2 JIC M 1/2 JIC AD / (5 m) M 1/2 JIC M 1/2 JIC KREMLIN's advice If you want to set your heater on your cart mount pump assembly, please select a two arm cart.

37 ONE-PASS HEATER The economical and reliable solution for a constant spraying quality to reduce the viscosity of paints without adding solvents. The heating of the product is done in one single passage in the One-pass TM heater thanks to the new design and the optimized thermal exchange efficiency. This innovative design offers the possibility to install directly the One-pass heater directly between the pump and the gun without recirculation. Its dimensions and reduced weight allow to fit it on a mobile pump (2 arms cart and mounting plate) To be used in zone 1 and 2 according to ATEX Heaters Agreement ISSeP 05ATEX031 Ex II 2 G - Ex d IIA T3 Features Standard stainless steel version A thermometer is integrated into the command box Reduced dimensions Modular design t max : 68 F (20 C) at an ouput of 800 cc/mn Benefits Compatible with water-based materials No pressure loss when working with high viscosity materials Mounting on mobile versions Quick and easy maintenance Optimised performances in most applications SPECIFICATIONS Thermostat type By fluid expansion and dry contact Thermal fuse Cut at F / (72 C) Thermometer Graduation F / (0-60 C) Temperature range F / (15-45 C) Pressure 1800 psi / (120 bar) Weight 36.4 lb / (16.5 kg) Wetted parts Stainless steel and PTFE Room temperature maximum 104 F / (40 C) ONE-PASS HEATER PART NUMBERS - stainless steel versions Stainless steel Voltage / Power Temperature Cable length Fitting One-pass heater Volt Watt w/o plug Inlet Outlet One-pass 230V F (15-45 C) 16 5 / (5 m) M 1/2 JIC M 1/2 JIC One-pass 115V F (15-45 C) 16 5 / (5 m) M 1/2 JIC M 1/2 JIC KREMLIN's advice If you want to set your heater on your cart mount pump assembly, please select a two arm cart 37

38 accessories for hot spraying Accessories for hot spraying Y- fitting - stainless steel Allowing paint circulation on the gun while maintaining ease of use. Remote set-up possible using an additional hose. Y-FITTING PART NUMBERS Fittings on gun Hoses thread Stainless steel Y-fitting - for airspray guns F 3/8" NPS M 1/4" NPS Stainless steel Y-fitting - for AIRMIX guns F 1/2" JIC M 1/2" JIC Circulation valve (for all types of spraying) Allows you to set the perfect output for circulation. Max. fluid pressure : 3600 psi (240 bar) CIRCULATION VALVES PART NUMBERS Thread Back fitting Flushing valve Flushing rod Pump intake Rod M 18 x 125 F 26 x 125 M 26 x 125 M 1/2 JIC M 1"G M 35 x 150 M 3/4 JIC Airmix back pressure regulator Assures a constant pressure in the fluid circuit. Regulation pressure : psi (0-70 bar) AIRMIX BACK PRESSURE REGULATOR PART NUMBERS Thread Version Back fitting Flushing Flushing rod valve M 18 x 125 Pump intake Rod Wall-mounted F 26 x 125 M 26 x 125 M 1/2 JIC

39 39Notes

40 EXEL Advanced Technology systems with a guarantee Why do most finishing systems only come with a 1 year manufacturers warranty on the product not the process? Its because most systems integrators or distributors do not control the entire process. What makes EXEL ADVANCED TECHNOLOGY Group different? It is because we believe in our process and products. our specialities Robotic Applications - Multi axis robots - Robotic integration Reciprocation Paint Kitchens Process Control PLC Control UV Finishing Color Changers Speciality Gun Movers Fluid Delivery Electrostatics - Liquid - Powder Electronic Proportioning Powder Booths Process Evaluations OUR GUARANTEE The EXEL ADVANCED TECHNOLOGY Group will provide a system performance guarantee based on the mutual acceptance of performance criteria before & after the installation for 6 months. All other equipment other than wear parts are guaranteed for 2 years one shift. OUR PROCESS Market Specialists Design Engineering Process Engineering Controls Engineering State of the Art Lab CAD Layouts Project Management Installation Teams Site Supervision Training Department Large Solution & Service Network In House Repair 40

41 Making Manufacturers More Competitive At your service A worldwide network Training centres all over the world : Paris, Detroit, Barcelona, Düsseldorf, Shanghaï, Mumbay, Sao Paulo... Advanced Technology Lab 1 Plymouth, MI Advanced Technology Lab 2 Plymouth, MI Visit our website Plymouth, MI 41

42 EXEL Industries... An International Presence Canada EXEL North America, consisting of our American, Canadian and Mexican subsidiaries, is a wholly owned subsidiary of EXEL Industries. They bring four finishing, fluid handling and dispensing brands under one company banner. The four brands offer the widest range of controlled application equipment for finishing and dispensing in the world. Our Vision To remain the global leader in high value added custom and standard solutions for controlled applications of powders and fluids, thick or thin, in the industrial and automotive markets. Our Values We are a team of people with integrity that have a mission-to-serve with a sense of urgency in delivering the right solution and service through our network of Solution and Service Centers. Our Mission Making Manufacturers More Competitive Finishing Fluid Handling Dispensing 42

43 EXEL A north american Presence Precision Finishing, Fluid Handling and Dispensing Brands Non-electrostatic guns, pumps and accessories for thin fluids Electrostatic application equipment for liquid and powder Dispense heads, pumps and accessories for thick fluids Full Range of Equipment Manual Airspray Manual Airmix Manual Liquid Electrostatic Manual Powder Automatic Non-Electrostatic Automatic Liquid Electrostatic Automatic Powder Fluid Delivery Pumps & Accessories Extrusion (RAM) Pumps & Accessories Plural Component Systems & Accessories Wood Manufacturing Markets Served Industrial Feeder Plants Automotive Plymouth, Michigan Scarborough, Ontario Monterrey, Mexico Plymouth, Michigan Scarborough, Ontario Monterrey, Mexico Plymouth, Michigan Scarborough, Ontario Monterrey, Mexico Plymouth, Michigan Scarborough, Ontario Monterrey, Mexico EXEL R&D, Testing, Training, Distribution and Manufacturing Locations Over 100 North American Solution and Service Centers for Customer Sales and Service 43

44 Making Manufacturers More Competitive EXEL North America, Inc. North American Headquarters Mile Road Plymouth, MI Toll Free: (800) Phone: (734) Fax: (734) EXEL North America, Inc. Canadian Branch 931 Progress Ave., Unit 7 Scarborough, Ontario M1G 3V5 Toll Free: (800) Phone: (416) Fax: (416) EXEL-NA, S.A. de C.V. Mexico Branch Bernardo Garza Treviño # 1715 Col. Del Maestro, Monterrey, N.L. Mexico CP Phone: (81) Fax: (81) General Catalog Manual Airspray Manual Airmix Manual Electrostatic Manual Powder Automatic Spray Automatic Electrostatic Fluid Delivery Selection Guide Plural Components 2009 EXEL North America, Inc. Making Manufacturers More Competitive Finishing Fluid Handling Dispensing Hose & Accessory Selection Guide LT