Job Hazard/Safety Analysis For the Plumber
|
|
|
- Bridget Fox
- 8 years ago
- Views:
Transcription
1 Job Hazard/Safety Analysis For the Plumber 1
2 INTRODUCTION Job Hazard/Safety Analysis for the Plumber is a partial list of known task performed by the professional plumber. We have placed the tasks in alphabetical order and in a table format, listing each in a step-by-step sequence followed by the potential hazard and a recommended action or procedure. This is by no means an exhaustive list and is subject to modification. Additional comments may be added as more information becomes available. If you are asked to perform an occasional task, not listed with your job title, you can look up an individual task by returning to our Job Safety Analysis page and check the pulldown menu for Job Task. 2
3 APHABETICAL LIST OF TASK Page Air Compressor 5 Air Sprayer ATV 4-Wheeler 6 7 Auger, Posthole 8 Band Saw 9 Battery Charger 10 Bench Grinder 11 Chemicals (Pouring Handling) 12 Cleaning (Body fluid clean-up) 13 Cleaning (Sweep & Mop) 14 Compound Miter Saw 15 Cutoff Saw 16 Ditchwitch Trencher 17 Drill Bit Sharpener 18 Drill Press 19 Driving 20 Drum Handling (30-55 Gal.) 21 Floor Jack, Hydraulic 22 Hand Held Pneumatic Tools 23 Hand Held Portable Power Tools 24 Heat Gun High Pressure Washer Hydraulic Press Jack Stands, Manual 28 Lifting/Carrying Objects 29 Loft/Mezzanine/Roof Operations 30 LP Gas Torch (Propane Cylinder) 31 Oxygen Acetylene Torch 32 Pallet Jack & Dolly, Hydraulic 33 Parts Cleaner, Vat 34 Plate Compactor Pipe Threading and Cutting
4 Portable Arc Welder, Gas Powered 37 Portable Generator, Gas Powered 38 Portable Heater, Electric Powered 39 Portable Heater, Gas Powered 40 Power Hacksaw 41 Propane Torch (14-20 oz. Cylinder) 42 Sewer Snake 43 Shop Vac(s) 44 Soldering Gun_Irons Torch, Oxygen Acetylene Valves (Operating) Vise 48 4
5 Hazard Analysis: Air Compressor Shutdown and Isolate Unit Unit Activation during repair Auto start and/or human error Lockout/Tagout Routine Maintenance /Repair Routine Operation Noise Equipment Operation Hearing Protection Hand Injury Confined work areas, sharp edges Gloves Eye Injury Residual air pressure Goggles, safety glasses with side shields Electric Shock Improper operation and maintenance Manufacturer s instructions strictly followed, lock-out/tagout Noise Equipment Operation hearing protection Noise Equipment Operation hearing protection Eye Injury Blowing debris safety glasses w/side shields or goggles Goggles/Safety Glasses with side shield Hearing Protection Gloves Hazard Analysis: Air Compressor, Portable, Electric Routine Maintenance /Repair Routine Operation Electric Shock Improper operation and maintenance Unplug electrical cord and retain control of plug during repair/maintenance Noise Equipment operation hearing protection Trauma Eye Injury Improper use, uncontrolled release of compressed air Projectiles, flying debris appropriate nozzle for specific work activity, situational awareness Goggles or safety glasses with side shields Goggles or Safety glasses with side shield Hearing Protection 5
6 Hazard Analysis: Air Sprayer Shutdown and Isolate Unit Routine Maintenance/Repair Unit Activation during repair Auto start and/or human error Lockout/Tagout Noise Equipment Operation Hearing Protection Hand Injury Confined work areas, Gloves sharp edges Eye Injury Residual air pressure Goggles, safety glasses with side shields Electric Improper operation and Shock Maintenance Manufacturer s instructions strictly followed, lockout/tag-out Noise Equipment Operation hearing protection Routine Operation Noise Equipment operation hearing protection Safety Glasses with side shield Hearing Protection Gloves 6
7 Hazard Analysis: ATV 4-Wheeler Routine Maintenan ce/repair Routine Operation Hand Injury Confined work areas, sharp edges/objects, rotating parts Gloves, situational awareness Foot Injury Equipment rolls over foot, Wear safety shoes object drops on foot Trauma Rotating parts Situational awareness, appropriate clothing Muscle/Ligam ent Strain Awkward working positions Position body to avoid strains, take appropriate breaks Eye Injury Flying Particles Goggles/Safety Glasses w/side shields Noise Equipment Operation hearing protection Noise Equipment Operation hearing protection Head Injury Fall from 4-Wheeler, accident Wear helmet Helmet Safety glasses, goggles or helmet face shield Gloves Hearing Protection Safety Shoes/boots protective clothing (optional) 7
8 Hazard Analysis: Auger (Post Hole), Gasoline Powered Inhalation Dust/particles generated during machine operation, exhaust fumes Appropriate natural ventilation, disposable respirators Eye Injury Projectiles Safety glasses with side shield or appropriate safety goggles Trauma Projectiles, point of operation, flying debris & sparks, improper use and operation, loose clothing becoming entangled Situational awareness, PPE, machine guards, Manufacturer s instructions followed, do not wear loose clothing Noise Engine Ear plugs/ear muffs Foot Injury Drop object on foot, impact of Safety shoes auger Hand Injury Point of operation, in-going nip points, rotating parts, flying debris and sparks Gloves, machine guards, situational awareness Fire Sparks Appropriate placed fire extinguisher, remove all combustibles and fire hazards Gloves (leather) Goggles/Safety Glasses w/side shield disposable respirator (optional) Safety Shoes/boots Hearing Protection 8
9 Hazard Analysis: Band Saw Inhalation Hazardous fumes, gases, dusts Appropriate ventilation, as required, disposable respirators Eye Injury Projectiles Safety glasses with side shield or appropriate safety goggles Trauma Projectiles, rotating parts, point of operation, ingoing nip points, flying chips & sparks Situational awareness, PPE, protective clothing, machine guards Foot Injury Drop object on foot Wear safety shoes Hand Injury Sharp objects Gloves as appropriate for task Fire Sparks Appropriate placed fire extinguisher, remove all Electrical Shock Improper grounding, improper operations and maintenance combustibles and fire hazards Proper grounding of frame, manufacturer s instructions strictly followed protective Clothing (optional) Goggles/Safety Glasses w/side shield Face Shield Safety Shoes/Boots disposable Respirator (optional) 9
10 Hazard Analysis: Battery Charger Foot Injury Drop object on foot Wear safety shoes Trauma (Burns) Batty acid spills Goggles, apron, gloves, proper battery handling procedures Eye Injury Battery acid splashes Goggles, appropriate battery handling procedures Electrical Shock Improper operation and maintenance, battery condition Lockout/tagout, manufacturer s instructions strictly followed Fire Sparks, improper storage of flammables, combustibles Appropriate placed fire extinguisher, remove all combustibles and fire hazards Explosion Spark/poor ventilation, smoking, improper procedures from machine area Adequate ventilation, no smoking, follow manufacturer s instructions Apron Gloves Safety Shoes/Boots Goggles 10
11 Hazard Analysis: Bench Grinder Inhalation Dust/particles generated during machine operation Appropriate natural ventilation, disposable respirators Eye Injury Projectiles Safety glasses with side shield or appropriate safety goggles Trauma Projectiles Situational awareness, PPE, protective clothing, machine guards Foot Injury Drop object on foot Wear safety shoes Hand Injury Impact, penetration, Gloves, situational awareness compression Head Projectiles Face Shield Protection Fire Heat, sparks Appropriate placed fire extinguisher, remove all combustibles and fire hazards from grinding/buffing area Electrical Shock Improper grounding, Improper operations and maintenance Lockout/tagout, proper grounding of frame, manufacturer s instructions strictly followed protective Clothing (optional) Goggles/Safety Glasses w/side shield Face Shield Safety Shoes/Boots disposable Respirators (optional) Gloves 11
12 Hazard Analysis: Chemicals (Pouring/Handling) Eye Injury Splash, fumes Goggles Contact irritation, burn or absorption Splash, skin contact Gloves (appropriate type for chemical), apron (if necessary), long sleeves Ingestion Breathing fumes Wear respirator if needed Face Splash Wear Face Shield (if necessary) Goggles Gloves protective Clothing (apron) Respirator (as needed) Face shield (if necessary) 12
13 Hazard Analysis: Cleaning (Body Fluid Clean-Up) Eye Injury Fumes, splashes and Goggles, face shield dusts (cleaning agents) Trauma Sharp objects, impact Situational awareness, gloves Foot Injury Dropped object on Wear safety shoes (if necessary) foot Inhalation Chemicals, body fluids Wear respirator or dust mask (if needed), gloves Goggles Face shield Safety Shoes/boots (if necessary) Gloves (chemical/biological resistant) protective Clothing (Apron) Respirator or dust mask (as needed) 13
14 Hazard Analysis: Cleaning (Sweeping/Mopping/Buffing) Trauma Projectiles, impact, chemical contact Situational awareness, gloves, protective clothing Foot Injury Dropped object on foot Wear safety shoes Ingestion Chemicals, dust Wear respirator or dust mask if needed Safety Shoes/boots Gloves (optional) protective Clothing (long pants recommended to prevent chemical splash on skin) Respirator or dust mask (as needed) 14
15 Hazard Analysis: Compound Miter Saw Inhalation Dust/particles generated during machine operation Appropriate natural ventilation, disposable respirators Eye Injury Projectiles Safety glasses with side shield or appropriate safety goggles Trauma Projectiles, rotating parts, point of operation, ingoing nip points, flying chips & sparks situational awareness, PPE, protective clothing, machine guards Foot Injury Drop object on foot Wear safety shoes Hand Injury Point of Operation, ingoing nip points, rotating parts, flying chips & sparks Machine guards, situational awareness Fire Sparks Appropriate placed fire extinguisher, remove all combustibles and fire hazards Electrical Shock Improper grounding, improper operation and maintenance Proper grounding of frame, manufacturer s instructions strictly followed Protective Clothing (optional) Goggles/Safety Glasses w/side shield Safety Shoes/Boots Disposable Respirators (optional) 15
16 Hazard Analysis: Cutoff Saw Inhalation Dust/particles generated during machine operation Appropriate natural ventilation, disposable respirators, automatic vacuum machine Eye Injury Projectiles Safety glasses with side shield Trauma Projectiles, rotating parts, point of operation, ingoing nip joints, flying chips & sparks Foot Injury Drop object on foot Safety shoes Hand Injury Point of Operation, ingoing nip points, rotating parts, flying chips and sparks or appropriate safety goggles Situational awareness, PPE, protective clothing, machine guards Machine guards, situational awareness Head Projectiles Face Shield Protection Fire Heat, sparks Appropriate placed fire extinguisher, remove all combustibles and fire hazards from area Electrical Shock Improper grounding, improper operations and maintenance Lockout/tagout, proper grounding of frame, manufacturer s instructions strictly followed Safety Shoes/Boots Safety glasses/goggles Face Shield (optional) disposable Respirators (optional) Hearing Protection 16
17 Hazard Analysis: Ditchwitch Trencher Routine Maintenanc e/repair Routine Operation Hand Injury Confined work areas, sharp edges/objects, rotating parts Gloves, situational awareness Foot Injury Equipment rolls over foot, object Wear safety shoes drops on foot Trauma Rotating parts Situational awareness, appropriate clothing Eye Injury Flying particles Safety glasses Noise Equipment Operation hearing protection Noise Equipment Operation hearing protection Head Injury Bump head, objects fall on head Wear hard hat (as necessary) Foot Injury Equipment rolls over foot, object Wear safety shoes drops on foot Hand Injury Sharp edges/objects Wear Gloves Protective Clothing Safety Shoes/Boots Safety Glasses Hard Gloves Hearing Protection 17
18 Hazard Analysis: Drill Bit Sharpener Eye Injury Projectiles, filings Safety glasses with side shield or appropriate safety goggles Hand Injury Point of operation, ingoing nip Situational awareness points, rotating parts, flying chips and sparks Electrical Shock Improper grounding, improper operations and maintenance Proper grounding of frame, manufacturer s instructions strictly followed Safety Glasses w/side shield 18
19 Hazard Analysis: Drill Press Inhalation Electrical Shock Sparks, friction Eye Injury Filings/particles generated during machine operation Improper grounding, improper operations and maintenance Inhalation Dust/particles generated during machine operation Appropriate natural ventilation, disposable respirators Trauma Projectiles, flying sparks Safety glasses with side shield or appropriate safety goggles situational awareness Foot Injury Projectiles, rotating parts, point Wear safety shoes of operation, ingoing nip points, flying chips & sparks Hand Injury Drop object on foot Gloves (optional), machine Head Protection Point of operation, ingoing nip points, rotating parts, flying chips & sparks guards, situational awareness Face shield (if necessary) Fire Projectiles Proper grounding of frame, manufacturer s instructions strictly followed. Appropriate placed fire extinguisher, remove all combustibles and fire hazards Protective Clothing (optional) Safety Shoes/Boots Goggles/Safety Glasses w/side shield disposable Respirators (optional) Face shield Gloves (optional) 19
20 Hazard Analysis: Driving Trauma Projectiles, impact, vibration, burns Situational awareness, gloves (optional), seat belts Noise Engine, impact Wear hearing protection for noise level over 85db Hearing Protection Gloves (optional) 20
21 Hazard Analysis: Drum, Gal (Handling) Eye Injury Splashes Goggles (for handling exposed chemicals) Trauma Impact Situational awareness, gloves Foot Injury Dropped object on foot Wear safety shoes Goggles Safety Shoes/boots Gloves 21
22 Hazard Analysis: Floor Jack, Hydraulic Foot Injury Roll jack over foot Wear safety shoes Trauma Overloading jack beyond rated capacity, using jack for support rather than just lifting Follow manufacturer s instructions. Ensure that rated load is legibly and permanently marked in a prominent location on jack, and rated capacity is not exceeded. Immediately support load once it is lifted. Safety Shoes/Boots 22
23 Hazard Analysis: Hand Held Pneumatic Tools Eye Injury Residual air pressure, flying debris Goggles/safety glasses with side shields, situational awareness Trauma Air pressure, ejection of tool Situational awareness, tool retainer Noise Equipment Operation hearing protection Safety Glasses with side shield/goggles Hearing Protection Gloves (optional) 23
24 Hazard Analysis: Hand Held Portable Power Tools Inhalation Dust/particles generated during machine operation Appropriate natural ventilation, disposable respirators (if necessary), automatic vacuum machine Eye Injury Projectiles Safety glasses with side shield or appropriate safety goggles Foot Injury Drop object on foot Wear safety shoes Hand Injury Point of operation, ingoing nip points, rotating parts, flying chips & sparks Machine guards, situational awareness Head Projectiles Face Shield Protection Fire Sparks Appropriate placed fire extinguisher, remove all combustibles and fire hazards from machine area Noise Machine operation Hearing protection Electrical Shock Improper grounding, improper operations and maintenance Proper grounding of frame, manufacturer s instructions strictly followed Protective Clothing (optional) Safety Shoes/Boots Goggles/Safety Glasses w/side shields Disposable Respirators (optional) Face shield, as appropriate Hearing Protection 24
25 Hazard Analysis: Heat Gun Inhalation Fumes, vapors and gases generated during use Properly ventilated work area, use disposable respirators Burns Hot air, contact with heat gun Situational awareness, gloves Electrical Shock Improper operation & maintenance Manufacturer s instructions strictly followed, replace worn parts Gloves disposable Respirators (optional, if appropriate) 25
26 Hazard Analysis: High Pressure Washer, Gasoline Powered Trauma Flying debris, contact with high pressure stream Situational awareness, protective clothing Hand Injury Flying debris, contact with high Situational awareness, gloves pressure stream Head Injury Flying debris Situational awareness, face shield, hard hat (as necessary) Foot Injury Drop object on foot, contact Wear safety shoes with high pressure stream Eye Injury Flying debris Goggles/safety glasses with side shields, face shield Electric Shock Improper operation and maintenance Manufacturer s instructions strictly followed Fire Smoking, sparks No smoking or exposure to sparks or open flame during fueling. Appropriate placed fire extinguisher. Noise Equipment Operation hearing protection Protective Clothing (optional) Safety Shoes/Boots Goggles Hard Hat (as necessary) Face shield Gloves Hearing Protection Apron (optional) 26
27 Hazard Analysis: Hydraulic Press Eye Injury Projectiles Safety glasses with side shield or appropriate safety goggles Trauma Projectiles, moving parts, point of operation, pinch points, flying items Situational awareness, PPE, protective clothing, machine guards Foot Injury Drop object on foot Wear safety shoes Hand Injury Point of operation, pinch points, moving parts, flying items. Head Protection Projectiles Gloves, machine guards, situational awareness Face Shield (as necessary) Protective Clothing (optional) Safety Shoes/Boots Goggles/Safety Glasses w/side shield Gloves Face shield (as necessary) 27
28 Hazard Analysis: Jack Stands, Manual Foot Injury Improper placement of load Situational awareness, wear safety shoes Trauma Overloading vehicle stand beyond rated capacity Follow manufacturer s instructions. Ensure that rated load is legibly and permanently marked in a prominent location on vehicle stand, and rated load capacity is not exceeded. Safety Shoes/Boots 28
29 Hazard Analysis: Lifting/Carrying Objects Trauma Impact Situational awareness, gloves, back brace/belt (optional) Foot Injury Dropped object on foot Wear safety shoes/boots Safety Shoes/boots Gloves Back brace/belt (optional) 29
30 Hazard Analysis: Loft/Mezzanine/Roofing Operations Trauma Impact, falls Situational awareness, gloves, fall protection (restraint) Foot Injury Dropped object on foot Wear safety shoes Safety Shoes/boots Fall Protection (restraint) Gloves 30
31 Hazard Analysis: LP Gas Torch (14oz to 20oz Propane Cylinder) Inhalation Eye Injury Hazardous fumes, gases, dusts Projectiles, fumes, dusts, flashes Appropriate natural or mechanical ventilation, and disposable respirators, as required Goggles/safety glasses w/side shields, appropriate noncombustible or flameproof screens Trauma Projectiles, burns Situational awareness, gloves Foot Injury Equipment Operation Wear safety shoes Fire Heat, sparks, slag Appropriate placed fire extinguisher, remove all combustibles and fire hazards from area Safety Shoes/Boots Gloves Goggles/Safety Glasses w/side shields disposable respirator (optional) protective Clothing (optional) 31
32 Hazard Analysis: Oxygen-Acetylene Torch Inhalation Eye Injury Hazardous fumes, gases, dusts Projectiles, fumes, dusts, flashes Appropriate mechanical ventilation, as required, respirator Helmets, safety glasses w/side shields/ goggles, appropriate noncombustible or flame-proof screens Trauma Projectiles, burns Situational awareness, PPE, protective clothing Foot Injury Drop object on foot Wear safety shoes Fire Heat, sparks, slag Appropriate placed fire extinguisher, remove all combustibles and fire hazards from welding area Protective Clothing disposable Respirators Safety Shoes/Boots Goggles/Safety Glasses w/side shields 32
33 Hazard Analysis: Pallet Jack & Dolly, Hydraulic Foot Injury Roll jack over foot Wear safety shoes Trauma Overloading jack beyond rated capacity, using jack for support rather than just lifting, sharp objects Follow manufacturer s instructions, gloves Safety Shoes/Boots Gloves 33
34 Hazard Analysis: Parts Cleaner, Vat Inhalation Organic vapors, hydrocarbons Appropriate ventilation, respirators when needed Eye Injury Chemical splash, fumes Goggles and face shield Skin Irritation/Absor ption Chemical splash, contact with vat liquids Situational awareness, gloves, protective clothing Foot Injury Drop object on foot Wear safety shoes Fire Heat, sparks, slag Appropriate placed fire extinguisher, remove all combustibles and fire hazards from area Protective Clothing (Rubber Apron) Safety Shoes/Boots Goggles and Face Shield Disposable Respirator (Optional) Rubber gloves 34
35 Hazard Analysis: Plate Compactor Eye Injury Projectiles, fumes, dusts Safety glasses w/side shields or goggles Trauma Projectiles, impact, vibration, burns Situational awareness, gloves, protective clothing, back brace/belt (optional), switch guards Foot Injury Dropped object on foot Wear safety shoes Noise Engine, impact Wear hearing protection Inhalation Dust Wear respirator or dust mask if needed Safety Glasses w/side shields or Goggles Safety Shoes/boots Hearing Protection Gloves protective Clothing (long pants) Respirator or dust mask (as needed) Back brace/belt (optional) 35
36 Hazard Analysis: Pipe Threading and Cutting Foot Injury Drop object on foot Safety Shoes Electric Shock Hand Injury Improper operation and maintenance, improper grounding Point of operation, rotating Manufactures instructions strictly followed, proper grounding Gloves, situational awareness parts Eye Injury Flying particles Safety glasses w/side shields Noise Running equipment Hearing protection for noise in excess of 85db Safety Glasses w/side shields Safety Shoes/ Boots Gloves Hearing Protection 36
37 Hazard Analysis: Portable Arc Welder, Gasoline Powered Inhalation Eye Injury Hazardous fumes, gases, dusts Projectiles, fumes, dusts, flashes Appropriate ventilation, respirator as required Helmets, goggles/safety glasses, appropriate noncombustible or flameproof screens Trauma Projectiles, burns Situational awareness, PPE, protective clothing, switch guards Foot Injury Drop object on foot Wear safety shoes Fire Heat, sparks, slag Appropriate placed fire extinguisher, remove all combustibles and fire hazards from machine area Electrical Shock Improper grounding, improper operations and maintenance, improper switching device Lockout/tagout, proper grounding of secondary and case portable welding transformers, manufacturer s instructions strictly followed, proper switching for shutting down machine Safety Shield/Helmet with Filter Lens Fire resistant gauntlet gloves Safety shoes/boots Respirator Safety glasses w/side shields or Goggles Protective Clothing (Full sleeves, no front pockets, no cuffs, Shirt left outside of trousers, made of clean fire-resistant materials) 37
38 Hazard Analysis: Portable Generator, Gasoline Powered Inhalation Exhaust Appropriate ventilation Trauma Burns Situational awareness, PPE, protective clothing Foot Injury Roll over foot, drop object on Wear safety shoes foot Fire Heat, sparks, slag Appropriate placed fire extinguisher, remove all combustibles and fire hazards from area Electrical Shock Improper operations and maintenance, improper switching device Strictly follow manufacturer s instructions, proper switching for starting up/ shutting down machine Leather Gloves Safety Shoes/ Boots 38
39 Hazard Analysis: Portable Heater, Electric Powered Trauma Burns Situational awareness, PPE, protective clothing Foot Injury Roll over foot, drop object on Wear safety shoes foot Fire Heat, sparks, slag Appropriate placed fire extinguisher, remove all combustibles and fire hazards from area Electrical Shock Improper operations and maintenance, improper switching device Strictly follow manufacturer s instructions, proper switching for starting up/ shutting down machine Leather Gloves Safety Shoes/ Boots 39
40 Hazard Analysis: Portable Heater, Gasoline Powered Inhalation Exhaust Appropriate ventilation Trauma Burns Situational awareness, PPE, protective clothing Foot Injury Roll over foot, drop object on Wear safety shoes foot Fire Heat, sparks, slag Appropriate placed fire extinguisher, remove all combustibles and fire hazards from area Electrical Shock Improper operations and maintenance, improper switching device Strictly follow manufacturer s instructions, proper switching for starting up/ shutting down machine Leather Gloves Safety Shoes/ Boots 40
41 Hazard Analysis: Power Hacksaw Inhalation Dust/particles generated during machine operation, exhaust fumes Appropriate natural ventilation, respirators when needed Eye Injury Projectiles, burns Safety glasses with side shield or appropriate safety goggles Head Projectiles Face shield (as necessary) Protection Trauma Projectiles, point of operation, flying chips & sparks, improper use and operation Foot Injury Drop object on foot Safety shoes Hand Injury Point of operation, in-going nip points, rotating parts, flying chips and sparks Situational awareness, PPE, protective clothing, machine guards, manufacturer s instructions strictly followed Machine guards, situational awareness Fire Sparks Appropriate placed fire extinguisher, remove all combustibles and fire hazards from machine area Protective Clothing (optional) Safety Shoes/ Boots Goggles/Safety Glasses w/side shield Respirators (if needed) Face Shield (as necessary) 41
42 Hazard Analysis: Propane Torch (14oz to 20oz Propane Cylinder) Inhalation Eye Injury Hazardous fumes, gases, dusts Projectiles, fumes, dusts, flashes Appropriate natural or mechanical ventilation, and disposable respirators, as required Goggles, face shield, appropriate noncombustible or flame-proof screens Trauma Projectiles, burns Situational awareness, PPE Foot Injury Drop object on foot Wear safety shoes Fire Heat, sparks, slag Appropriate placed fire extinguisher, remove all combustibles and fire hazards from area Gloves Safety Shoes/Boots Goggles/Safety Glasses Respirator (if needed) Protective Clothing (optional) 42
43 Hazard Analysis: Sewer Snake Trauma Contact with moving parts Situational awareness, safety shoes Electrical Shock Improper operations and maintenance, improper Strictly follow manufacturer s instructions, proper grounding grounding Hand Injury Point of operation, moving Gloves, situational awareness parts Eye Injury Flying particles Goggles/Safety glasses w/side shields Noise Equipment operation Hearing Protection Atmospheric hazard Methane gas, hydrogen sulfide, oxygen deficient atmosphere Follow Permit-Required Confined Space Alternate Entry Procedures when entering sewer manholes or lift stations Safety Glasses w/side shields or Goggles Safety Shoes/Boots Gloves Hearing Protection 43
44 Hazard Analysis: Shop Vac(s) Foot Injury Drop object on foot Wear safety shoes Electrical Shock Improper operations and maintenance, improper grounding Manufacturer s instructions strictly followed, proper grounding Eye Injury Flying debris Wear safety glasses w/side shields Noise Equipment Operation hearing protection PPE Required :( PPE required to be worn during the vacuuming task when it poses a specific hazard to the user) Safety Glasses with side shields Hearing Protection Safety Shoes/Boots 44
45 Hazard Analysis: Soldering Guns/Irons Inhalation Fumes, vapors and gases generated during soldering Properly ventilate work area, use respirator Eye Injury Spattering Safety glasses w/side shields/goggles Skin irritation/burning Chemical cleaner use, hot soldering iron Review MSDS, substitute cleaner with non-toxic product, use appropriate PPE/protective clothing Foot Injury Drop object on foot Wear safety shoes Fire Hot soldering iron Appropriate placed fire extinguisher, remove all combustibles and fire hazards from soldering area Electrical Shock Residual surface contamination Some fluxes contain toxic compounds (i.e. cadmium and fluorides) Improper operation and maintenance Soldering with lead containing solders Toxic compounds in fluxes Manufacturer s instructions strictly followed, replace worn parts Wipe down work area when finished Review MSDS, substitute with nontoxic compounds if available Safety glasses w/side shields/goggles Safety Shoes/Boots (for protection against dropped objects when necessary) Protective Clothing Respirators (when needed) 45
46 Hazard Analysis: Torch, Oxygen- Acetylene Inhalation Hazard fumes, gases, dusts Appropriate mechanical ventilation, as required, respirator Eye Injury Projectiles, fumes, dusts, flashes Helmets, Safety glasses w/side shields or goggles, appropriate noncombustible or flame-proof screens Trauma Projectile, burns Situational awareness, PPE, protective clothing Foot Injury Drop object on foot Wear safety shoes Fire Heat, sparks, slag Appropriate placed fire extinguisher, remove all combustibles and fire hazards from the area Protective Clothing (full sleeves, no front pockets, no cuffs, shirt left outside of pants, made of clean fire-resistant materials) Eye Safety Shield/Helmet with filter lens Respirator (Optional) Safety Shoes/ Boots Goggles/ Safety Glasses w/side shields Fire resistant gauntlet gloves 46
47 Hazard Analysis: Valves (Operating) Eye Injury Projectiles, fumes, dusts Safety glasses w/side shields or goggles (for chemical piping), face shield (if needed) Trauma Projectiles, impact, burns Situational awareness, gloves, protective clothing (long sleeves/pants) Foot Injury Dropped object on foot Wear safety shoes Safety Glasses w/side shields or Goggles Safety Shoes/boots Gloves protective Clothing (long sleeves/pants) Face Shield (if needed) 47
48 Hazard Analysis: Vise Eye Injury Projectiles Safety glasses with side shield or appropriate safety goggles Foot Injury Drop object on foot Wear safety shoes Hand Injury Impact, penetration, compression Gloves, situational awareness Goggles/ Safety Glasses w/ side shield Gloves Safety Shoes/Boots 48
Job Hazard/Safety Analysis For the Building Maintenance Worker
Job Hazard/Safety Analysis For the Building Maintenance Worker 1 INTRODUCTION Job Hazard/Safety Analysis for the Building Maintenance Worker is a partial list of known task performed by the professional
Job Hazard/Safety Analysis For the Paint & Finish Worker
Job Hazard/Safety Analysis For the Paint & Finish Worker 1 INTRODUCTION Job Hazard/Safety Analysis for the Paint & Finish Worker is a partial list of known task performed by the professional paint and
Job Hazard/Safety Analysis For the Grounds Keeper
Job Hazard/Safety Analysis For the Grounds Keeper 1 INTRODUCTION Job Hazard/Safety Analysis for the Grounds Keeper is a partial list of known task performed by the professional grounds worker. We have
Job Hazard/Safety Analysis For the Lab Worker
Job Hazard/Safety Analysis For the Lab Worker 1 INTRODUCTION Job Hazard/Safety Analysis for the Lab Worker is a partial list of known task performed by the professional laboratory worker. We have placed
Job Hazard/Safety Analysis For the Housekeeper
Job Hazard/Safety Analysis For the Housekeeper 1 INTRODUCTION Job Hazard/Safety Analysis for the Housekeeper is a partial list of known task performed by the professional housekeeper. We have placed task
Job Hazard Analysis Manual. Updated 10/6/04
Job Hazard Analysis Manual Updated 10/6/04 Abrasive Cutoff Saw General Use Inhalation Dust/particles generated during machine operation Appropriate natural ventilation, disposable respirators, automatic
Notes. Material 1. Personal Protective Equipment 2.
29CFR 1926.20(b)-Accident Reduction, 29CFR 1926.21- Safety Training & Education 29CFR 1926.20(a)-Unsafe Working Conditions 29 CFR 1910.132-138, the "Personal Protection Equipment" standard. & 20 CFR 1910.134
Job Hazard/Safety Analysis For the Office Worker
Job Hazard/Safety Analysis For the Office Worker 1 INTRODUCTION Job Hazard/Safety Analysis for the Office Worker is a partial list of known task performed by the professional office worker. We have placed
Tech Shop Safety Level 2 - FN000425. Tech Shop / Tool Safety Operations. (Fermilab machines not covered in course FN000258)
Tech Shop Safety Level 2 - FN000425 Tech Shop / Tool Safety Operations (Fermilab machines not covered in course FN000258) Table of Contents Tech Shop / Tool Safety Operations 3 General Rules of Safety
WEEKLY SAFETY MEETING All Euramax Subsidiaries WELDING SAFETY / HOT WORK SAFETY. Safety Meeting Contents. Meeting Notice.
Safety Meeting Contents Meeting Notice Leaders Guide Employee Handout Employee Quiz Meeting Sign-In Sheet Employee Puzzle PRIOR TO THE WEEKLY MEETING: - Post the meeting notice by the timeclock - Read
ALVERNIA UNIVERSITY OSHA REGULATION: 29 CFR 1910.252 WELDING, CUTTING, AND BRAZING ( HOT WORK ) SECTION: 3600
OSHA REGULATION: 9 CFR 90.5 WELDING, CUTTING, AND BRAZING ( HOT WORK ) A. POLICY. This procedure follows requirements set forth in 9 CFR 90.5.. This policy applies to all Hot Work operations being done
SAFETY in the work area is a broad topic because of the
A Safe Place to Work SAFETY in the work area is a broad topic because of the many components of agricultural mechanics. Safety is protection from injury or loss. Injury can result from improper use of
PERSONAL PROTECTIVE EQUIPMENT FOR CALIFORNIA STATE UNIVERSITY, LOS ANGELES
PERSONAL PROTECTIVE EQUIPMENT FOR CALIFORNIA STATE UNIVERSITY, LOS ANGELES OCTOBER 2007 PROGRAM APPROVAL AND AUTHORIZATION James M. Rosser, President Date TABLE OF CONTENTS TITLE Section PURPOSE...1.0
Installation Instructions for Alarm Module Kit A043F059
Instruction Sheet 07-2013 Installation Instructions for Alarm Module Kit A043F059 1 Introduction The information contained within is based on information available at the time of going to print. In line
Personal Protective Equipment Policy & Procedure Date: August, 2001 Approved by:
OCCUPATIONAL SAFETY AND HEALTH POLICY Topic: Personal Protective Equipment Policy & Procedure Date: August, 2001 Approved by: Author(s): Distribution: Cindy Davis, Risk Management; Ed Polluconi, EH&S;
GEORGIA INSTITUTE OF TECHNOLOGY ENVIRONMENTAL HEALTH AND SAFETY PERSONAL PROTECTIVE EQUIPMENT
PURPOSE To protect the health and welfare of GEORGIA TECH employees in areas where there may be a risk of injury or exposure to hazardous substances or conditions employees who work in areas where physical
Compressed Gas Cylinder Storage and Handling Guide
Overview Compressed gas cylinders are used in many workplaces to store gases that vary from extremely flammable (acetylene) to extremely inert (helium). Many compressed gas cylinders are stored at extremely
Oxy-Fuel Gas Welding. Given a functional oxy-fuel gas unit, instruction and demonstration of use, each student will be able to:
I. Competencies Oxy-Fuel Gas Welding Given a functional oxy-fuel gas unit, instruction and demonstration of use, each student will be able to: A. Identify the major parts of the oxy-fuel gas unit. B. Pass
Conducting a Job Hazard Assessment. Environmental, Health and Safety 275-3241
Conducting a Job Hazard Assessment Environmental, Health and Safety 275-3241 EH&S Programs: Fire Safety Blood Borne Pathogens Hazard Communication Personal Protective Equipment Emergency Preparedness General
Safety Training Topic PERSONAL PROTECTIVE EQUIPMENT
Safety Training Topic PERSONAL PROTECTIVE EQUIPMENT Purpose of Meeting To remind workers that using personal protective equipment (PPE) can protect them from serious injury. To reince PPE safety rules.
Pressure Vessels (Air Compressors) and LPG Tanks
Pressure Vessels (Air Compressors) and LPG Tanks 1. Identification of Workplace Hazard Any container, tank or vessel that contains pressurized material is a potential hazard to employees due to the force
University of Glasgow School of Engineering UGRacing Formula Student Garage
University of Glasgow School of Engineering UGRacing Formula Student Garage James Watt South Building Level 4 CODE OF PRACTICE Emergency telephone number is 4444 Fire extinguishers located next to emergency
PALM BEACH STATE COLLEGE PERSONAL PROTECTIVE EQUIPMENT (PPE) JOB HAZARD ASSESSMENT
PALM BEACH STATE COLLEGE PERSONAL PROTECTIVE EQUIPMENT (PPE) JOB HAZARD ASSESSMENT Department: Facilities Campus: All Task: Check/Service/Maintain/Repair/Install HVAC Equipment and Systems Job Title(s)
Respiratory Safety and PPE Module 7. Special Warehouse Worker Hazards in Structural Steel Fabricating and Supply Companies
Respiratory Safety and PPE Special Warehouse Worker Hazards in Structural Steel Fabricating and Supply Companies Drawing from OSHA 3384-09 2011 1 Respiratory Safety and PPE OSHA Grant Information This
Master Workplace Inspection Checklist for General Shop Safety. MASTER WORKPLACE INSPECTION CHECKLIST General Shop Safety
Integrated Risk Management Master Workplace Inspection Checklist for General Shop Safety Document Type: Form Control Number: UIRM- FM_012_50 File Code: UIRM-001 Last Reviewed: March 2014 Department/Unit:
Welcome to the safe@work Automotive Module.
Welcome to the safe@work Automotive Module. Have you read the General Module, completed the test and gained your safe@work General certificate? The Automotive Module should be done AFTER the General Module
Mechanical Systems Competency 1.20
Competency 1.20 Mechanical systems personnel shall demonstrate a working level knowledge of the safety and health fundamentals of mechanical systems and/or components. 1. Supporting Knowledge and Skills
TEMPORARY EMPLOYEES SAFETY PROCEDURES
TEMPORARY EMPLOYEES SAFETY PROCEDURES Temporary Agencies will ensure that any temporary employee sent to work at Modern will have received and understand the General Safety Rules. GENERAL SAFETY RULES
Curtain Guards Made of PVC and designed to protect the operator from the risk of airborne chips or tool fragments.
Two General Safety Rule for CNC Machines Never operate a CNC machine without proper training or consulting the specific operator's manual for that particular machine and control type. Never attempt to
"ACCIDENT PREVENTION AND SAFETY HOUSEKEEPING"
MAJOR PROGRAM POINTS "ACCIDENT PREVENTION AND SAFETY HOUSEKEEPING" Part of the "GENERAL SAFETY SERIES" Quality Safety and Health Products, for Today...and Tomorrow Outline of Major Points Covered in the
HOT WORK PERMIT PROGRAM TRAINING. John Braun
HOT WORK PERMIT PROGRAM TRAINING John Braun 1.0 INTRODUCTION 1.2 Purpose The Hot Work Permit Program has been developed for University employees that work on or around hot work activities. This program
Example risk assessment for a motor vehicle mechanical repair workshop
Example risk assessment for a motor vehicle mechanical repair workshop Setting the scene The garage manager did the risk assessment. The business employed 12 mechanics, including two apprentices who carried
PERSONAL PROTECTIVE EQUIPMENT (PPE)
Page 1 of 6 (PPE) Personal protective equipment (PPE) is used to protect an individual from hazards associated with their work tasks or environment. Specific types of personal protective equipment include
Fire Safety in Laboratories. University of Tennessee Environmental Health and Safety
Fire Safety in Laboratories University of Tennessee Environmental Health and Safety Fire Safety in Laboratories Fire Prevention is a vital aspect of laboratory safety. Requires knowledge and constant vigilance
Presented by: Rich Perry Marsh Risk Consulting
Flammable and Combustible Liquids Presented by: Rich Perry Marsh Risk Consulting What s the Big Deal? Flammable and combustible liquids are easily ignited Ignite with explosive force Burn readily and give
National- Spencer Inc.
9-27-2010 National- Spencer Inc. 19.2V HEAVY DUTY GREASE GUN PRODUCT SPECIFICATION Charger Input Power 110 VAC Battery Output Power 19.2V Battery Capacity 1500 MAH Battery Pack Charge Time 1 Hour Maximum
If you have any questions about how to safely undertake a task or project, ask your supervisor before you begin.
Laboratory Health and Safety Manual Section 1: Introduction and Objectives This manual provides a set of minimum standards and practices for the safe and healthy operation of a laboratory. Following the
Metal welding safety. Guidance Note. Practical advice for employers on controlling hazards when welding. June 2011. Background. How to use the table
Guidance Note Metal welding safety Practical advice for employers on controlling hazards when welding. June 2011 Background Metal welding involves the application of heat to join two metals together. The
Safe Operating Procedure
Safe Operating Procedure (Revised 11/11) JOB SAFETY ASSESSMENTS (For assistance, please contact EHS at (402) 472-4925, or visit our web site at http://ehs.unl.edu.) This SOP is intended for supervisors
Hazards in the Workplace
Hazards in the Workplace Fact Sheet: Confined spaces Confined spaces are a major hazard to workers who are required to work within these areas. Confined spaces include, but are not limited to, storage
How many work-related eye injuries are there each day?
EYE SAFETY Common Eye Hazards Dust, concrete, and metal particles Falling or shifting debris, building materials, and glass Smoke and noxious or poisonous gases Chemicals (acids, bases, fuels, solvents,
Safe Operating Procedure
Safe Operating Procedure (Revised 11/15) PERSONAL PROTECTIVE EQUIPMENT (PPE) EYES AND FACE Introduction Eye and/or face is mandated by federal Occupational Safety and Health Administration (OSHA) standards,
Notes. Material 1. Appropriate Flammable Liquids
29 CFR 1910.106 Flammable Materials Flammable Liquids Preparation 1. Read Applicable Background information and related Company Policy Chapter. 2. Make Copies of this Lesson Plan for Personnel 3. Make
FRAME DOOR OPENING, DOOR AND SIDE PANEL OUTER
NUBIRA/LACETTI FRAME DOOR OPENING, DOOR AND SIDE PANEL OUTER 6 1 SECTION 6 FRAME DOOR OPENING, DOOR AND SIDE PANEL OUTER CONTENTS 1. FRAME DOOR OPENING........................................... 6 2 1.1.GENERAL
PERSONAL PROTECTIVE EQUIPMENT HAZARD ASSESSMENT, EQUIPMENT SELECTION AND TRAINING DOCUMENTATION
DRAFT SAMPLE WRITTEN PERSONAL PROTECTIVE EQUIPMENT HAZARD ASSESSMENT, EQUIPMENT SELECTION AND TRAINING DOCUMENTATION For Compliance With 1910.132 Wyoming General Rules and Regulations Wyoming Department
Forename: Surname: School / College/ Institution. Course date: / / RDTHSC:
Specialist Extension Level S5HS Forename: Surname: School / College/ Institution Course date: / / RDTHSC: These Training and Accreditation Guidelines are based on the following essential publications:
Course Title: Safety Issues in Electronics Engineering Technology Number of Credits: 3 B.A. B.S. B.A.S A.A. A.S. Degree Type
GENERAL INFORMATION Name: Diane King Phone #: 77021 Course Prefix/Number: ETI3704 Course Title: Safety Issues in Electronics Engineering Technology Number of Credits: 3 B.A. B.S. B.A.S A.A. A.S. Degree
PERSONAL PROTECTIVE EQUIPMENT POLICY & GUIDANCE
Health and Safety Policy PERSONAL PROTECTIVE EQUIPMENT POLICY & GUIDANCE ROYAL FREE HOSPITAL NHS TRUST & SCHOOL OF MEDICINE CONTENTS 1. SUMMARY OF THE REGULATIONS 2. INTRODUCTION 3. DEFINITION OF PERSONAL
PLASMA CUTTER - 35 AMP
PLASMA CUTTER - 35 AMP 45949 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright 2003 by Harbor Freight Tools.
Machine/Woodworking Shop The Basic Rules
Machine/Woodworking Shop The Basic Rules 1. Eye protection or face shields are required when working in the shop. A selection of protective goggles and safety glasses are available in the shop. The eyeglasses
SOLVENT CLEANER MSDS Page 1 of 5 SAFETY DATA SHEET. (To comply with OSHA s Hazard Communication Standard 29CFR 1910.1200/ANSI z400.
SOLVENT CLEANER MSDS Page 1 of 5 SAFETY DATA SHEET (To comply with OSHA s Hazard Communication Standard 29CFR 1910.1200/ANSI z400.1-1993) 1. PRODUCT & COMPANY IDENTIFICATION Prepared on: Month, Year Manufactured
Abrasive Wheel Grinder Safety
Abrasive Wheel Grinder Safety One of the most common pieces of machinery in use in the maintenance shops on campus is the abrasive wheel grinder. These useful machines, used to remove metal from flat and
University of Tennessee Safety Guidelines
University of Tennessee Safety Guidelines Guideline Subject: Compressed Gases and Cryogenics Safety Guidelines Approval Date: 10/1/15 (Rev. 1) Next Scheduled Review: 10/1/19 Date Effective: 1/01/09 Contact
HOT WORK PERMIT PROCEDURES
COLUMBIA UNIVERSITY ENVIRONMENTAL HEALTH & SAFETY HOT WORK PERMIT PROCEDURES COLUMBIA UNIVERSITY MEDICAL CENTER February 2010 1 TABLE OF CONTENTS A. PURPOSE 3 B. SCOPE 3 C. POLICIES AND PROCEDURES 3-4
Dining Services OSHA Safety Training Program TRAINING RECORD
Dining Services OSHA Safety Training Program TRAINING RECORD Employee Title: This record documents the safety training received by Dining Services employees, including student employees, as required by
Date: 22 June 2005 Version: 2 Revision: 1. 1. Identification of the substance/preparation and company/undertaking
Page 1 of 5 1. Identification of the substance/preparation and company/undertaking Product identifier Use Details of supplier of the safety data sheet Engine oil Telephone number +44-20-7186-0400 FAX number
NFPA Hazard Class: * Physical Form: Solid. Health: 0 (Least) * Appearance: Yellow Flammability: 1 (Slight)
Safety Data Sheet Microcrystalline Wax 1. Chemical Product Identification Generic Name: Microcrystalline Wax INCI Name: Microcrystalline Wax Chemical Family: Mineral Emergency Telephone Numbers: Page 1
Personal Protective Equipment Guidelines
Personal Protective Equipment Guidelines Purpose To establish guidelines for use and care of personal protective equipment, which is to be used by employees and /or students when a hazard is found to exist
Student Shop Safety Policy GS92 Page 1
Policy Subject: Student Shop Safety Effective: 8/1/2012 Affected Area: Machine Shops on Campus Reviewed/Revised: 8/1/2012 1.0 Purpose, Applicability, and Scope 1.1 Purpose- This policy identifies the requirements
TYPICAL FIRE SAFETY INSPECTION VIOLATIONS
TYPICAL FIRE SAFETY INSPECTION VIOLATIONS The following is a list of typical violations often found by inspectors and a generic solution. You can use this list to improve the safety of your facility, to
120Volt 60-70A ARC WELDER. 80000 Rev 80000-20080214
80000 Rev 80000-20080214 10006 Santa Fe Springs Road Santa Fe Springs, CA 90670 USA Made in China Owner s Manual and Operating Instructions 120Volt 60-70A ARC WELDER Table of Contents Introduction...
LOS ANGELES UNIFIED SCHOOL DISTRICT DIVISION OF ADULT AND CAREER EDUCATION SAFETY TEST FOR ELECTRICIAN PROGRAM
LOS ANGELES UNIFIED SCHOOL DISTRICT DIVISION OF ADULT AND CAREER EDUCATION SAFETY TEST FOR ELECTRICIAN PROGRAM Service Area: Industry Sector: Energy, Environment & Utilities Class Teacher (Please Print)
Enviro Safety Products Resource Center. OSHA Checklist for General Industry
Enviro Safety Products Resource Center OSHA Checklist for General Industry The Occupational Safety and Health Administration (OSHA) require many standards to be met by businesses and industries. OSHA sets
SAFETY DATA SHEET. Trade name: Master Clear Seal-5 Revised: 5/29/2015
MMG Mud Masters Group a division of Horizon Mud Company SAFETY DATA SHEET SECTION 1: Identification of the substance/mixture and of the company/undertaking Trade name: Master Clear Seal-5 Supplied by:
Material Safety Data Sheet
1. Product & Company Identification: Product: Conrad Energy Kamera-Akku Manufacturer: Conrad Electronic SE Nominal capacity: 1500 mah Nominal voltage: 7,4 V Address: Klaus-Conrad-Strasse 1, D-92240 Hirschau
Hazard/Risk Identification and Control Procedure
Hazard/Risk Identification and Control Procedure Introduction Hazard identification and the steps taken to minimize the risks associated with identified hazards are a critical component of working safely.
Chemical Reducing Solution CRS
Chemical Reducing Solution CRS Material Safety Data Sheet (MSDS) Revised: August 21, 2012 Supplier: Section 1 Supplier Information and Material Identification 1011 Calle Sombra San Clemente, CA 92673 Telephone:
ALVERNIA UNIVERSITY OSHA REGULATION: 29 CFR 1910.1200 HAZARD COMMUNICATION SECTION: 1700 REVISION DATE: 2/3/2012 REVISION: 4 NUMBER:
OSHA REGULATION: 29 CFR 90.200 HAZARD COMMUNICATION 700 : DATE: /3/200 DATE: 2/3/202 A. POLICY. This procedure follows requirements set forth in 29 CFR 90.200. 2. It is the policy of Alvernia University
MATERIAL SAFETY DATA SHEET DATE: 2009, revised July 2011 PRODUCT NAME: BOSTON BRAKE & PARTS CLEANER PRODUCT CODE: 78200
MATERIAL SAFETY DATA SHEET DATE: 2009, revised July 2011 PRODUCT NAME: BOSTON BRAKE & PARTS CLEANER PRODUCT CODE: 78200 SUPPLIER S NAME : SECTION I SUPPLIER IDENTIFICATION CAMPBELLS WHOLESALE PTY LTD ADDRESS
IMPORTANT SAFETY NOTICE
IMPORTANT SAFETY NOTICE To: Our Valued Customers User safety is a major focus in the design of our products. Following the precautions outlined in this manual will minimize your risk of injury. ITT Goulds
Guidelines for the Use of. Personal Protective Equipment
Guidelines for the Use of Personal Protective Equipment Contents Introduction 1 Key Points on the Proper Use of Personal Protective 2 Equipment Safety Helmets 3 Eye Protectors 4 Ear Protectors 5 Respirators
MODEL T-4 TRENCHER. Operators Manual
DO NOT THROW AWAY IMPORTANT MANUAL MODEL TRENCHER Operators Manual P.O.BOX 290 San Bernardino, CA. 92402 Phone (909) 478-5700 (800) 922-4680 Fax (909) 478-5710 E-mail: sales@groundhoginc.com www.groundhoginc.com
Document the assessment, PPE selection, and training.
Requirements... 1 Hazard Control... 1 Supervisor Responsibilities... 2 How to Use This Website... 3 Step One - Assessment... 3 Step Two - Selection... 3 Step Three - Training... 4 Step Four - Documentation...
Contents. 1. Legal Requirement 1. 2. Responsibility of Related Parties 2. 3. What are Confined Spaces 3. 4. Hazards Identification 4
Contents 1. Legal Requirement 1 2. Responsibility of Related Parties 2 3. What are Confined Spaces 3 4. Hazards Identification 4 5. Chemical Substances 6 6. Physical Hazards 7 7. Risk Assessment Report
1.0 Purpose... 4. 2.0 Definitions...4. 3.0 Hot Work Operations. 5
HOT WORK PROGRAM Introduction The University of Kentucky recognizes a potential for fire from hot work operations. For that reason this program should be implemented in all departments at the University
Trade Name of this Product Isopropyl Rubbing Alcohol 91% USP. Corporate Compliance Team 1666 East Touhy Avenue
Page 1 of 5 MSDS Document Product 1. Chemical Product and Company Identification Trade Name of this Product Manufacturer Contact Name Lawson Products, Inc. Corporate Compliance Team 1666 East Touhy Avenue
Personal protective equipment (PPE) at work A brief guide
Personal protective equipment (PPE) at work A brief guide Introduction This leaflet describes what you, as an employer, may need to do to protect your employees from the risk of injury in the workplace.
Safety Training Needs Assessment
Safety Needs Assessment Form Instructions: Please review each question and either check YES or NO. If a question is checked YES you will be required to complete the training topic before initial assignment
Industrial Process Pump Safety Manual IMPORTANT SAFETY NOTICE
Industrial Process Pump Safety Manual IMPORTANT SAFETY NOTICE To: Our Valued Customers User safety is a major focus in the design of our products. Following the precautions outlined in this manual will
Laboratory Safety and Environmental Health Assessment Program
Laboratory Safety and Environmental Health Assessment Program Principal Investigators and Faculty are vital to the success of safety and environmental compliance programs in Colorado School of Mines research
Technical Data Sheet
Februar, 2014 Technical Data Sheet PLA Polylactide Cas No. 9051-89-2 PLA is a thermoplastic resin derived from annually renewable resources Product Characteristics Typical Properties Value Unit Physical
The Real Dangers Threatening Workers Who Enter Permit Required Confined Spaces
The Real Dangers Threatening Workers Who Enter Permit Required Confined Spaces Gary K. Yurt Sr. President/Chief Safety Advisor ISTS - Industrial Safety & Training Services Louisville, Kentucky gary@istsky.com
Material Safety Data Sheet
Date of Issue: 26/5/2009 MSDS No.: Q54-1300B Material Safety Data Sheet 1. PRODUCT AND COMPANY IDENTIFICATION Product Name : Daily Maintenance Kit(Wipe Cleaning) Product Code : IP6-108 -Application model
Standard Operating Procedure
Standard Operating Procedure FLAMMABLE LIQUIDS This standard operating procedure (SOP) is intended to provide general guidance on how to safely work with flammable liquids. This SOP is generic in nature
RESPIRATORY PROTECTION PROGRAM
RESPIRATORY PROTECTION PROGRAM OFFICE of ENVIRONMENTAL HEALTH & SAFETY Campus Location: Physical Plant 521 S. Razorback Road Telephone: 479 575 5448 Web site: http://www.phpl.uark.edu Applies to all UofA
Safety Data Sheet for Whole Grain
SECTION 1: IDENTIFICATION Safety Data Sheet for Whole Grain PRODUCT NAME: SDS NUMBER: WHOLE GRAIN GRAIN SYNONYMS/OTHER MEANS OF IDENTIFICATION: INTENDED USE: FOOD MANUFACTURER: (company name) EMERGENCY
Employee Safety Handbook
i Table of Contents I. Introduction Background.................. 1 Health and Safety Policy.................. 1 Health and Safety Responsibilities................. 1 Employees Responsibilities..................
Best Practices for Handling Nanomaterials in Laboratories
Best Practices for Handling Nanomaterials in Laboratories Much of the toxicology of nanomaterials is currently uncertain or unknown. Some nanosized particles are more toxic than their respective micron
Safety Data Sheet Customwood MDF
1. IDENTIFICATION OF THE MATERIAL AND SUPPLIER. Product Details Product Name: Other Names: Manufacturer s code: U.N. Number: Dangerous Goods Class: HAZCHEM Code: Toxic Substances Schedule: Uses: Customwood
SAFETY DATA SHEET 安 全 数 据 单
SAFETY DATA SHEET 安 全 数 据 单 1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE COMPANY/UNDERTAKING PRODUCT NAME: InnoPlus LDPE 2420D CHEMICAL NAME: Low Density Polyethylene MANUFACTURER: 14 Map
PROJECT HAZARD ASSESSMENT FORM CHEMICAL HAZARDS
PROJECT HAZARD ASSESSMENT FORM PI/SPONSOR: Completion of the following form will serve as a risk assessment, personal protective equipment (PPE) assessment and guide to required training for the activities
ACCIDENT PREVENTION IN THE QUARRY INDUSTRY IN SA July 2011
ACCIDENT PREVENTION IN THE QUARRY INDUSTRY IN SA July 2011 Introduction Accident prevention requires the creation and maintenance of a safe working environment, and the promotion of safe behaviour. Accident
Questar Safety Data Sheet
Page 1 1. Product and Company Identification Product Name: Natural Gas (with and without the addition of an odorant) Synonyms: Methane; NG (CNG when compressed) UN Number: 1971 Recommended Use: Fuel Gas
Company Name Company Address Company Phone Number Company Fax Number
Job Hazard Analysis Plumbing Company Name Company Address Company Phone Number Company Fax Number Job/Task Plumbing fixture and piping Date Prepared: 08.04.2010 installation Project Name: Project Name
Risk management a practical approach
Risk management a practical approach Introduction Preventing work related accidents and injuries is the primary concern for all those involved in health and safety. Work related accidents and injuries
Notes. Material 1. Tools the employee is expected to operate
OSHA Standard29 CFR 1910.211-.247, Subpart O, Machinery and Machine Guarding, and Subpart P, Hand and Portable-Powered Tools and other Hand- Held Equipment. Hand Tool Safety Preparation 1. Read Applicable
School of Engineering University of Glasgow
School of Engineering University of Glasgow Electronics Workshops Rankine Building 319A (2 Technicians) 510 (1 Technician) 712A (4 Technicians, 1 Modern Apprentice) James Watt South 619 (2 Technicians)
A. a security guard B. a competent scaffold erector C. your boss D. the ship repair manager
01 If a worker is injured at work, he should. A. make sure it does not affect his work B. continue working until he is not able to C. go home to rest immediately without informing his employer or supervisor
Autoclave Safety. Autoclaves are sterilizers using high pressure and high temperature steam. The potential safety risks for the operators are:
Autoclave Safety Purpose: Sterilization refers to the complete killing of all living organisms, including spores. Common sterilization techniques include the application of wet heat, dry heat, chemicals,
A SELF-EVALUATION CHECKLIST of BEST PRACTICES for AUTO REFINISH SHOPS and SCHOOLS
A of BEST PRACTICES for AUTO REFINISH SHOPS and SCHOOLS www.epa.gov/dfe/pubs/projects/auto/ WHAT IS THE DESIGN FOR THE ENVIRONMENT (DFE) AUTO REFINISH PROJECT? The DfE Program has been working with the