Owner s Manual - ROOM AIR CONDITIONER WINDOW/WALL RADS-81G RADS-101G RADS-121G HEAT CONTROLLER, INC.

Transcription

1 HEAT CONTROLLER, INC. Owner s Manual WINDOW/WALL - TYPE ROOM AIR CONDITIONER Room MULTI-STEP Conditioner SPEED ELECTRONIC CONTROL with R-410A: RADS-81G RADS-101G RADS-121G Before using your air conditioner, please read this manual carefully and keep it for future reference. Heat Controller, Inc Wellworth Ave. Jackson, MI (517)

2 Owner s Manual Room Conditioner with R-410A Heat Controller, Inc. CONTENTS 1. SAFETY PRECAUTIONS IMPORTANT SAFETY INSTRUCTIONS NORMAL SOUNDS AIR CONDITIONER FEATURES INSTALLATION INSTRUCTIONS CARE AND CLEANING TROUBLESHOOTING TIPS...15 Read This Manual Inside you will find many helpful hints on how to use and maintain your air conditioner properly. Just a little preventive care on your part can save you a great deal of time and money over the life of your air conditioner. You'll find many answers to common problems in the chart of troubleshooting tips. If you review our chart of Troubleshooting Tips first, you may not need to call for service at all. CAUTION Contact the authorised service technician for repair or maintenance of this unit. an authorized service technician repair or of this unit. Contact the installer for installation of this unit. The air conditioner is not intended for use by young children or infirm persons Contact an authorized installer installation of this unit. without supervision. If the power cord needs to be replaced, replacement work shall be performed by Young children should be supervised to ensure that they do not play with the air authorized service personnel only. conditioner. If the power cord is to be replaced, replacement work shall be performed by Installation work must performed in accordance with national and local authorised personnel only. electric codes and must be performed by authorized personnel only. Installation work must be performed in accordance with the national wiring standards by authorised personnel only. 1 1

3 Heat Controller, Inc. Room Conditioner with R-410A Owner s Manual Safety Precautions To prevent injury to the user or other people and property damage, the following instructions to the user propert damage, the instructions must be must be followed. Incorrect operation due to ignoring of instructions may cause harm or operation due to ignoring instructions may cause or damage. damage. The seriousness The seriousness is classified by the following indications. is following indications. WARNING This symbol indicates the possibility of death or serious injury. CAUTION This symbol indicates the possibility of injury or damage to property. Meanings of symbols used in this manual are as shown below. Plug in power plug cord properly. plug properly Otherwise, it may cause electric it electric shock or fire due to or excess heat generation. Do not modify power cord length or share Do not modify power cord the outlet with other length or share the outlet appliances. with other appliances. It It may cause electric shock or electric shock or fire due to heat generation. Never do this. Always do this. WARNING Do not operate or stop the open the unit unit by inserting or pulling during operation out the power plug. It may cause electric shock or fire electric shock due to heat generation. Do not operate or stop the unit by inserting or Do not operate with wet pulling out the power hands or in damp plug environment. It may cause electric shock. electric shock or fire due to heat generation Always ensure effective Do not operate with Do not allow water to run use the power Always install circuit Do not allow water earthing. wet hands or in a into electric parts. cord close heating breaker and a dedicated to run in to electric power circuit. damp environment appliances parts Incorrect earthing may cause It may cause failure of machine Incorrect installation may cause It electric shock. may cause electric shock or electric shock. It may cause fire and electric shock fire and electric shock. It may cause failure of machine or electric shock Unplug the unit if strange Do not use the socket if it is Do not open the unit sounds, smell, or smoke Unplug the unit if loose or damaged. Always install circuit during operation. Do not use the socket if comes from it. strange sounds, breaker and a dedicated it is loose or damaged It may cause fire and electric odors or smoke It may cause fire and electric power circuit It may cause electric shock. shock. comes from it. shock. Incorrect installation may cause It may cause fire and electric shock It Keep firearms away. may cause and electric shock Do not use the power cord fire and electric shock Do not use the power cord near close to heating appliances. flammable gas or combustibles, such as gasoline, benzene, thinner, etc. Do not use a damaged or unspecified power cord Do not use the power It may cause fire. It may cause fire and electric It may cause an explosion or fire. cord near flammable gas It may cause electric shock or fire shock. or combustiblies, such If the power cord is damaged, it must be replaced by the manufacturer or an authorized Ventilate room before operating air serivce center or a qualified person in order to avoid Do not disassemble or modify unit. a hazard gasoline, benzene, conditioner if there is a gas leakage from thinner, etc. another appliance. Do not disassemble or modify unit. It may cause an explosion or fire It It may cause explosion, fire and, burns. failure and electric shock It may cause failure and electric shock. 2 2 Do not damage or use an Always ensure unspecified power cord. effective grounding It may cause electric shock or fire. Incorrect grounding If the power cord is damaged, it electric shock must be replaced by the manufacturer or an authorised service centre or a similarly qualified person in order to avoid a hazard. strange sounds, Unplug the unit if Do not direct airflow at odors or smoke room occupants only. comes from it. This could damage your health. It may cause fire and electric shock

4 Owner s Manual Room Conditioner with R-410A Heat Controller, Inc. CAUTION When the air filter is to be is to be removed, do not touch the do touch the metal parts of the unit. the It It may cause an injury. an due to sharp edges of components. Do not clean the air allow water to conditioner with water. enter inside the unit during cleaning Water may enter the unit and enter the and degrade degrade the insulation. It may cause an electric shock cause an electric shock. Ventilate the room well when the used together with a stove, when with etc. a gas stove or if there is a gas leak An oxygen shortage may occur. An oxygen shortage may occur May cause explosion, fire and/or burns When the unit is to be is to be cleaned, switch off, and turn cleaned, switch off, and off the circuit breaker. turn off the circuit breaker Do not clean unit when Do not clean unit when power is on as it may power is on as it may cause cause fire and electric shock fire and electric shock, it may cause an injury. Stop operation and close Stop operation and close the window in storm or the window in storm or hurricane hurricane. Operation with windows opened may allow Operation with windows rain to enter inside and damage property opened may cause wetting of indoor and soaking of household furniture. Do not place obstacles Do not place obstacles around air-inlets or inside around air-inlets or inside of air-outlet It may of air-outlet. cause failure of appliance or accident It may cause failure of appliance or accident. Do not use strong detergents such as wax or thinner; Do not use strong detergent such as wax or use a damp, soft cloth Appearance thinner but use a soft cloth. may be deteriorated due to change of product color or scratching Appearance may be of its surface deteriorated due to change of product color or scratching of its surface. Use caution when unpacking and installing. Sharp edges could cause injury. Do not put a pet or house Hold the plug by the plant where it will be head of the power plug exposed to direct air flow. when taking it out This could injure the pet or It may cause electric shock and damage plant. Ensure that the installation bracket of of the power plug when outdoor appliance is Hold the plug by the head taking it out. not damaged It may cause electric shock If bracket is damaged, there is concern and damage. of damage due to falling of unit. Do not place heavy object the power cord Ensure that the installation bracket of the outdoor appliance is not damaged and ensure that due to prolonged exposure. cord is not compressed There If bracket is damaged, there danger of fire or electric shock is concern of damage due to falling of unit. Use caution when unpacking and installing Do not place heavy object on the power cord and ensure that the cord Sharp is not compressed. edges could cause injury There is danger of fire or electric shock. Do not use for special Turn off the main power purposes. switch when not using the unit for a long time Do not use this air conditioner to preserve precision devices, food, It may cause failure of product or fire pets, plants, and art objects. It may cause deterioration of quality, etc. Always insert the filters Turn off the main power securely. filter switch when not once every two using the weeks unit for a long time. Operation without filters may cause It may cause failure of product or fire. Operation with dirty/clogged filters may cause failure Do not drink water Always insert the filters drained from air conditioner securely. filter once It every two weeks. contains contaminants and could make you sick Operation without filters may cause failure. If water enters the unit, turn the unit off at the Do not drink water drained from air conditioner. power outlet and switch off the circuit breaker. Isolate supply by taking It contains contaminants and power-plug out and contact a qualified service could make you sick. technician Water may enter the unit and degrade the insulation. It may cause an If water enters the unit, turn the unit off at the power electric shock outlet and switch off the circuit breaker. Isolate supply by taking the power-plug out and contact a qualified service technician. 3 3

5 Heat Controller, Inc. Room Conditioner with R-410A Owner s Manual IMPORTANT SAFETY INSTRUCTIONS NOTE The power supply cord with For some models, the power this air conditioner contains a current supply cord with this air conditioner detection device designed to reduce contains a current detection device the risk of fire. designed to reduce the risk of fire. Please refer to the section Operation the section Operation of Current Device for details. Device for In the event that the power supply cord is damaged, it cannot be repaired-it must be replaced with a cord from the Product Manufacturer.,, Do not, under any circumstances, cut, remove, or bypass the grounding prong. Power supply cord with 3-prong grounding plug and current detection device,, WARNING For your safety Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Avoid fire hazard or electric shock. Do not use an extension cord or an adaptor plug. Do not remove any prong from the power cord. WARNING Electrical Information Be sure the electrical service is adequate for the model you have chosen. This information can be found on the serial plate, which is located on the side of the cabinet and behind the grille. Be sure the air conditioner is properly grounded. To minimize shock and fire hazards, proper grounding is important. The power cord is equipped with a three-prong grounding plug for protection against shock hazards. Your air conditioner must be used in a properly grounded wall receptacle. If the wall receptacle you intend to use is not adequately grounded or protected by a time delay fuse or circuit breaker, have a qualified electrician install the proper receptacle. Ensure the receptacle is accessible after the unit installation. Do not run air conditioner without side protective cover in place. This could result in mechanical damage within the air conditioner. Do not use an extension cord or an adapter plug. Operation of Current Device Operation of Current Device The power supply cord contains a current device that senses damage to the power cord. To test your power supply cord do the following: (Applicable to the unit adopts current detection device only ) The power supply cord contains a current device that senses damage to the power cord. 1. Plug in the Conditioner. To test your power supply cord do the following: Plug in & 2. The power supply cord will have TWO buttons on the plug head. 1. Plug in the press RESET Conditioner. Press the TEST button, you will notice a click as the RESET 2. The power supply cord will have TWO buttons on the plug head. Press the button pops out. TEST button, you will notice a click as the RESET TEST button pops out. 3. Press the RESET button, again you will notice a click as the button 3. Press the RESET button, again you will notice a click as the button engages. engages. 4. The power supply cord is now supplying electricity to the unit. (On some products this it also indicated by RESET 4. a light on the plug head.) (On some products this it also indicated by a light on the plug head.) NOTE: Some plugs have NOTES: buttons on the top. Do not use this device to turn the unit on or off. NOTES: Always make sure the RESET button is pushed in for correct operation. Do not use this device to turn the unit on or off. The power supply must be replaced if it fails reset when either the TEST button is pushed, or it cannot be Always make sure the RESET reset. A new one can be obtained from the product manufacturer. button is pushed in for correct operation. The power supply must be replaced if it fails reset when either the If power supply cord is damaged, it cannot be repaired. It MUST be replaced by one TEST button is pushed, or it cannot be obtained from the reset. product manufacturer. A new one can be obtained from the product manufacturer. If power supply cord is damaged, it cannot be repaired. It MUST be replaced by one obtained from the product manufacturer. 4 4

6 Owner s Manual Room Conditioner with R-410A Heat Controller, Inc. At Sound the front of Rushing of the unit, you may hear the sound of rushing air being Sound of Rushing moved by the fan At the front of the unit, you may hear the sound of rushing air being moved by the fan Gurgle/Hiss Gurgling or hissing noise may be heard due to refrigerant passing Gurgle/Hiss through evaporator during normal operation. Gurgling or hissing noise may be heard due to refrigerant NORMAL SOUNDS NORMAL SOUNDS High Pitched Chatter WINDOW/WALL - TYPE ROOM AIR CONDITIONER High efficiency compressors may have a high pitched chatter during High Pitched Chatter the cooling cycle. High efficiency compressors may have a high pitched chatter during the cooling cycle. AIR CONDITIONER FEATURES Vibration Unit may vibrate and make noise because of poor wall or window construction Vibration or incorrect installation. Unit may vibrate and make noise and make noise because of poor wall or window or window construction or incorrect installation. or incorrect installation. Pinging or Switching Droplets of water hitting condenser during normal operation may cause pinging Pinging or Switching switching sounds. Swishing Droplets of water hitting condenser during normal operation may cause pinging or switching sounds. swishing NOTE: passing through evaporator All the pictures in this manual are for explanation purposes only. The actual shape of the during normal operation. air conditioner you purchased may be slightly different, but the operations and functions are almost the same. MULTI-STEP SPEED ELECTRONIC CONTROL ELECTRONIC CONTROL OPERATING INSTRUCTIONS CONTROL OPERATING INSTRUCTIONS Before Before you begin, thoroughly familiarize yourself with the control panel and remote as shown below familiarize familiarize yourself yourself the the panels panels as shown as below shown and below all its and all its functions. and all its functions, then follow the symbol for the functions you desire. The then unit follow can be the controlled symbol for by the the unit control you alone desire. or The with unit the remote. can The unit can be controlled controlled panel by the of by the unit control alone or with the remote. you bought or may look like remote one controller. of following: Before using your air conditioner, please read this manual carefully and keep it for future reference. ADJUSTS TEMPERATURE OR TIME ACTIVATES TIMER CHECK FILTER RESET BUTTON SETS MODE ENERGY SAVER MODE Tem p ADJUSTS TEMPERATURE OR TIME ACTIVATES TIMER On CHECK FILTER RESET BUTTON SETS MODE Dry ENERGY SAVER MODE Energy Timer Me Tem p Temp Timer Off Auto Low Dry Med High Energy On/Off ADJUSTS Temp TEMPERATURE OR TIME ADJUSTS TEMPERATURE Timer OR TIME On DISPLAYS TEMPERATURE DISPLAYS Off OR TIME TEMPERATURE OR TIME CLEAN AIR MODE SLEEP MODE Timer (on some models) Me UNIT CONTROL CLEAN AIR MODE (on some models) Auto SLEEP MODE Low Med SET FAN SPEED High SET FAN SPEED FOLLOW ME INDICATOR FOLLOW ME INDICATOR (on some models) (on some models) TURNS UNIT ON OR OFF TURNS UNIT ON OR OFF On/Off On Timer Temp/Timer Dry Cool High Med Energy Off Me Low On/Off Auto Auto UNIT CONTROL(1) UNIT CONTROL(2) 5 5 5

7 Heat Controller, Inc. Room Conditioner with R-410A Owner s Manual AIR CONDITIONER FEATURES(CONTINUED) NOTE: The following instructions represent the Unit Controls, the same instructions can be used for the Remote Control. TO TURN UNIT ON: Dry Med High Press the On/Off button. Energy Me On/Off TO CHANGE TEMPERATURE SETTING: Tem p On Timer Tem p Off Press to raise Press to lower NOTE: Press or hold either Left( <) or Right (>) button until the desired temperature is seen on the display. This temperature will be automatically maintained anywhere between 62 F(17 C) and 88 F(30 C). If you want the display to read the actual room temperature, see To Operate on Only section. TO ADJUST FAN SPEEDS: NOTE: Used to select the Speed in four steps- Auto, Low, Med or High. Each time the button is pressed, the fan speed mode is shifted. Dry Energy Me Med High On/Off Press to select appropriate fan speed 6 6

8 Owner s Manual Room Conditioner with R-410A Heat Controller, Inc. AIR CONDITIONER FEATURES(CONTINUED) TO SELECT THE THE NOTE: NOTE: OPERATING MODE: MODE: To choose To operating choose operating mode, press mode, mode, the press press the button. the button. button. Each time Each you time press you the press button, the the a button, mode is a selected mode a mode is selected is selected in a in a sequence that goes from Auto, Cool, Dry and sequence in a sequence that goes that from goes Auto, from Cool, Auto, Dry Cool, and Dry. and The. The indicator light beside will be illuminated and remained indicator. The on light once indicator beside the mode light each is beside selected. mode will be be illuminated and Dry Cool Auto and remained on once the mode is selected. remain on once the mode is selected. AIR To operate on Auto feature: CONDITIONER FEATURES(CONTINUED) Press DO the THIS: In this To mode, operate the fan on speed Auto cannot feature: be adjusted, it High Med Low Auto button. Press the starts automatically In this mode, at a the speed fan according speed cannot to the TO SELECT THE be adjusted, it button. NOTE: room temperature. starts automatically If the room does at a speed not get too according to the OPERATING Dry Med MODE: High To warm, choose it room will operating stay temperature. Low mode, speed. press the button. If the room does not get too Each time you press the button, a mode is selected To in operate a sequence warm, on that it will Only: goes stay from at Auto, Low Cool, speed. Dry and Energy Me MeOn/Off On/Off. Use The this function To indicator only operate light when on beside cooling Only: will be is illuminated not desired, and such remained as for room on once air circulation the mode or is to selected. exhaust stale air(on some Use models). this function (Remember only when to open cooling the vent is not desired, To during operate this such on function, Auto as for feature: but room keep air it circulation closed during or to exhaust stale Press the In cooling this mode, air(on for maximum the some fan speed cooling models). cannot efficiency.) (Remember adjusted, You can to it open the vent button. starts choose automatically during any fan speed this at function, you a speed prefer. according but keep it to closed the during room During temperature. this cooling function, If for maximum the display room does cooling will not show get efficiency.) the too actual You can Dry Med High TO USE THE ENERGY warm, room temperature, it will stay not Low the speed. set temperature as in the choose any fan speed you prefer. SAVER FEATURE: cooling mode. To operate During on this Only: function, the display will show the actual TO Energy USE Me THE On/Off ENERGY To Use operate this room function Dry temperature, only mode: when cooling not the is set not desired, temperature as in the such SAVER FEATURE: In this as mode, cooling for room the mode. air air circulation conditioner or will to exhaust generally stale air(on operate some in the models). form of (Remember a dehumidifier. to open Since the the vent during conditioned To this operate function, space is on but a Dry closed keep mode: it or closed sealed during area, some cooling degree In for of this cooling maximum mode, will cooling the continue. the air air conditioner efficiency.) You will will generally can generally operate in choose the operate any fan speed form of in a the you dehumidifier form prefer. of a dehumidifier. to remove moisture Since from the the During this function, the display will show the actual Press the button air. conditioned Since the conditioned space is a closed space is or a sealed closed area, or sealed some TO USE DryTHE ENERGY Cool Auto room temperature, not the set temperature as in the NOTE: area, degree some of cooling degree of will cooling continue. will continue. SAVER Dry FEATURE: cooling mode. Med High In this mode, the fan will continue to run for 3 minutes after To operate the compressor on Dry mode: shuts off. The fan then cycles High Med Low Auto Press the button NOTE: on In for this 2 minutes mode, the at air 10 minute conditioner intervals will generally until the room Energy Me On/Off temperature In this above mode, the set fan temperature, will continue at which operate in the form of a dehumidifier. Since the to run for 3 minutes time conditioned the after compressor the space compressor is turns a closed back shuts or on sealed and off. cooling area, The stars. some fan then cycles degree on of for cooling 2 minutes will continue. at 10 minute intervals until the room SLEEP FEATURE: temperature is above the set temperature, at which Energy Me On/Off Press the button time the compressor turns back on and cooling stars. NOTE: NOTE: Dry Med High In In this this mode mode, the the selected fan will continue temperature to run will for increase 3 minutes by 2 degrees F 30 minutes after the mode is selected. SLEEP FEATURE: after the compressor shuts off. The fan then cycles The on for temperature 2 minutes at will 10 then minute increase intervals by another until the 2 room degrees F after an additional 30 minutes. This new Energy Me On/Off temperature is above the set temperature, at which temperature NOTE: will be maintained for 7 hours before it time the compressor turns back on and cooling stars. returns to the originally selected temperature. This ends the In this mode mode and the the selected unit will temperature continue to will increase by SLEEP FEATURE: operate 2 as degrees originally F programmed. 30 minutes after The the mode is selected. Dry Med High program The can temperature be cancelled at will any then time increase during operation by another 2 NOTE: by again degrees pressing F the after an button. additional 30 minutes. This new Press In this mode button temperature the selected will temperature be maintained will increase for 7 hours by before it 2 degrees F 30 minutes after the mode is selected. Energy Me On/Off returns to the originally selected temperature. This Temp/Timer Press The temperature will then increase by another 2 ends the mode and the unit will continue to On Off button degrees F after an additional 30 minutes. This new temperature operate will be as maintained originally for programmed. 7 hours before The it mode program can be cancelled any time during operation Timer returns to the originally selected temperature. This 7ends the by again mode pressing and the the unit will continue button. to operate as originally programmed. The mode Dry Med High program can be cancelled at any time during operation by again pressing the button. Press button Energy Me On/Off 7 7 7

9 Heat Controller, Inc. Room Conditioner with R-410A Owner s Manual AIR CONDITIONER FEATURES(CONTINUED) TIMER: AUTO START/ STOP FEATURE: On Tem p On Timer Temp/Timer Timer Off Off Tem p Press Timer button Press Timer button NOTE: First First press the the Timer button, the the indicator light light besides word word On On illuminates. It It indicates the the Auto Auto Start Start program is is initiated. Press or or hold hold the the Left Left arrow or or Right arrow to to change the the Auto Auto time time by by hour hour increments, up up to to hours, then then at at 1 hour 1 hour increments up up to to hours. The The control will will count down the the time time remaining until until start. The The selected time time will will register in in 5 5 second and and the the system will will automatically revert back back to to display the the previous temperature setting. Turning the the unit unit ON ON or or OFF OFF at at any any time time will will cancel the the Auto Auto Start/Stop function. CHECK FILTER FEATURE: CHECK FILTER FEATURE: Dry Cool Auto Tem p Tem p High Med Low Auto On Timer Energy Me On/Off FOLLOW ME FEATURE: (on some models) CLEAN AIR FEATURE: (on some models) Dry Cool Auto High Tem p Med Low Tem p Auto On Off Off Energy Timer Me On/Off Press button Press button Light flashing Press button NOTE: This feature is a reminder to clean the for more efficient operation. The LED(light) will illuminate after 250 hours of operation. To reset after NOTE: cleaning the filter, press the button and This the light feature will is go a off. reminder to clean the for more efficient operation. The LED(light) will illuminate after 250 hours of operation. To reset after cleaning the filter, press the button and the light will go off. NOTE: This feature can be activated from the remote control ONLY. The remote control serves as a remote thermostat allowing for the precise temperature control at its location. To activate the Me feature, point the remote control towards the unit and press the Me button. The remote display is actual temperature at its location. The remote control will send this signal to the air conditioner every 3 minutes interval until press the Me button again. If the unit NOTE: does not receive the Me signal during any 7 Press minute the the interval, the button, button, unit will the the beep ion ion generator to generator indicate is the is ener- energized and Me and will mode will help help has to to ended. remove pollen and impurities impurities The from actual the from air, temperature and the trap air, and them can trap in be them displayed filter. in the filter. at the unit by pressing the Only mode. When in the Cool mode, the unit display indicates the set temperature. 8 8

10 Owner s Manual Room Conditioner with R-410A Heat Controller, Inc. AIR CONDITIONER FEATURES(CONTINUED) FOLLOW ME FEATURE: (on some models) Dry Energy Me Med High On/Off Light flashing NOTE: This This feature feature can can be be activated activated from from the the remote remote control ONLY. ONLY. The The remote remote control control serves serves as a as remote a thermostat remote thermostat allowing for allowing the precise for the temperature precise control at temperature its location rather control than at from its location. the unit s temperature sensor. To activate the Me feature, point the remote To control activate towards the the unit Me feature, and press point the the remote Me control button. towards The the remote unit and display press is the actual temperature Me button. The remote at its location. display is The actual remote temperature control at will its send location. this The remote signal control to the air will conditioner send this signal every to the 3 minutes air conditioner interval every until press 3 minutes the until the Me button Me again. button is If pressed the unit again. If does the unit not does receive not receive the the Me signal Me signal during during any 7 any minute interval, the unit will beep to indicate the 7 minute interval, the unit will beep to indicate the Me Me mode has ended. mode The actual has ended. temperature can be displayed at the unit The by pressing actual temperature the Only can be mode. displayed When at in the the unit Cool by pressing mode, the the unit display Only mode. indicates When the in the set Cool temperature. mode, the unit display indicates the set temperature. ADDITIONAL THINGS YOU SHOULD KNOW Now that you have mastered the operating procedure, here are more features in your control that you should become familiar with. The cooling Cool circuit has an automatic 3 minute time delayed start if start the unit if the is unit turned is turned off and off on and quickly. on This quickly. prevents This overheating prevents overheating of the compressor of the compressor and possible and circuit possible breaker circuit tripping. breaker The fan tripping. will continue The fan will to run continue during this to run time. during this time. The control will maintain any set temperature within 2 F, between 60 F and 90 F degrees. The control is capable of displaying temperature in degrees Fahrenheit or degrees Celsius. To convert from one to the other, press and hold the Left and Right Temp/Timer buttons at the same time, for 3 seconds. Fresh Vent Control(on some models): The Fresh Vent allows the air conditioner to: 1. Recirculate inside air - Vent Closed (See Fig.1) 2. Draw fresh air into the room- Vent Open (see Fig.2) 3. Exchange air from the room and draws fresh air into the room - Vent and Exhaust Open (see Fig.3) Figure 1 (VENT CLOSED) Figure 2 (VENT OPEN) Figure 3 (VENT & EXHAUST OPEN) 9 9

11 Heat Controller, Inc. Room Conditioner with R-410A Owner s Manual Directional Louvers The louvers will allow you to direct the air flow Up or Down and Left or Right throughout the room as needed. Pivot horizontal louvers until the desired Up/Down direction is obtained. Center Handles Direction Move the Center Handles from side to side until the desired Left/Right direction is obtained. INSTALLATION INSTRUCTIONS Your air conditioner is designed to install in standard double hung windows with opening widths of 22 to 36 inches(559mm to 914mm) (See Fig.1). STOOL SILL INTERIOR WALL OFFSET EXTERIOR WALL 22 to mm to 914mm 14 1 / 4 min. (337 mm) Fig.1 Lower sash must open sufficiently to allow a clear vertical opening of 14-1/2 inches (368mm). Side louvers and the rear of the AC must have clear air space to allow enough airflow through the condenser, for heat removal. The rear of the unit must be outdoors, not inside a building or garage. NOTE: Save Carton and these Installation Instructions for future reference. The carton is the best way to store unit during winter, or when not in use. Mounting Hardware TOOLS NEEDED: Phillips Screw Driver Drill(If pilot holes are needed) CAUTION: When handling unit, be careful to avoid cuts from sharp metal edges and aluminum fins on front and rear coils. 3 4 Screws (7) Lock Frame (2) Sash Lock (1) Top Rail Hardware NOTE: The top rail hardware and the following Fig.A, Fig.B and Fig.C are not applicable to the units more than 10000Btu/h. 3 8 Screws (4) Top Rail (1) Before installing unit, the top rail must be assembled on the unit (For <10000Btu/h models only). Tool Needed: Phillips Screwdriver A: Remove the air conditioner from the carton and place on a flat surface. B: Remove top rail from the bottom of the packaging material as shown in Fig.A 10 10

12 Owner s Manual Room Conditioner with R-410A Heat Controller, Inc. Fig.B Fig.C C: Align the hole in the top rail with those in the top of the unit as shown in Fig.B,, D: Secure the top rail to the unit with the 3/8 Screws as shown in Fig.C. NOTE: For safety reasons, all four(4) screws MUST be securely fastened. HOW TO INSTALL NOTE: Top Top rail rail and and Sliding Sliding Accordian Panels Panels at each at side each are side offset are to to provide provide the the proper proper pitch pitch to the to the rear rear of the of unit (5/16 (5/16 ).,, This This is necessary for for proper condensed water utilization and and drainage. drainage. If you If you are not are using not using the Side the Panels Side Panels for any for reason, any reason, this pitch this to the pitch rear to of the the rear unit must be be maintained. 1 Place unit on floor, a solid a surface. bench or There a table. is a There Left and is a Right Left and Window Right Filler Window Panel-be Filler sure Panel- to use be sure the to proper use the panel proper for each panel side. for When each side. installed, When the installed flange for the securing flange for the securing panel place the panel to the in window place to the sill will window be facing sill will into be the facing room. into the room. Fig.1 Fig.2A Fig.2B A. Hold the Accordion Panel in one hand and gently pull back the center to free the open end. See Fig.1. Fig.3 B. Slide the free end and (I section) of the panel into the cabinet as shown in Fig. 2A, 2B & 3. Slide the panel down., Be sure to leave enough space to slip the top and bottom of the frame into the rails on the cabinet

13 Heat Controller, Inc. Room Conditioner with R-410A Owner s Manual Fig.4 C. Once the panel has been installed on the side of the cabinet, make sure it sits securely inside the frame channel by making slight adjustments. Slide the top and bottom ends of the frame into the top and bottom ends of the frame into the top and bottom rails of the cabinet. Fig.4. D. Slide the panel all the way in and repeat on the other side. NOTE: If storm window blocks AC, see Fig. 13. Fig.5 2 Keep a firm grip on the air conditioner, carefully place the unit into the window opening so the bottom of the air conditioner frame is against the window sill (Fig.5). Carefully close the window behind the top rail of the unit. Fig.6 3 Extend the side panels out against the window frame (Fig.6). Fig.7 Fig.8 4 Place the the frame lock lock between the the frame frame extensions and and the the window,, sill sill as show as shown (Fig. 7). Drive (Fig.7). 3/4 Drive (19mm) 3 / 4 locking (19mm) screws locking through screws the frame through lock the and frame into the lock sill and (Fig. into 8). the sill NOTE: (Fig.8). To prevent window sill from splitting, drill 1/8 NOTE: (8mm) To,, pilot prevent holes window before driving sill from screws. splitting, drill 1 / 8 (3mm) pilot holes before driving screws

14 , Owner s Manual Room Conditioner with R-410A Heat Controller, Inc. Fig.9,, 5 Drive 1/2 1 / 2 (13mm) locking screws screws through through frame holes frame into window holes into sash window (Fig.9/10) sash (Fig. 9/10). 6 To secure lower,, sash in place, attach right angle sash lock with 3/4 3 / 4 (19mm) screw screw as as shown shown(fig.11). Fig.10 Fig.11 Fig.12 7 Cut foam seal and insert in the space between the upper and lower sashes (Fig.12). If AC is Blocked by Storm Window Fig.13 Add wood as shown in Fig.13, or remove storm window before air conditioner is installed. Storm window frame or other obstruction Sash,, 11/2 1-1/2 MIN (38 mm) Board thickness as required, for proper pitch to rear, along entire sill. Fasten with nails or screws. If Storm Window Frame must remain, be sure the drain holes or slots are not caulked or painted shut. Accumulated Rain Water or Condensation must be allowed to drain out. Removing AC From Window Turn AC off, and disconnect power cord. Remove sash seal from between windows, and unscrew safety lock. Remove screws installed through frame and frame lock. Close (slide) side panels into frame. Keeping a firm grip, on air conditioner, raise sash and carefully rock air conditioner backward to drain any condensate water in base of unit. Be carefully not to spill any remaining water while lifting unit form window. Store parts WITH air conditioner

15 Heat Controller, Inc. Room Conditioner with R-410A Owner s Manual CARE AND CLEANING CARE AND CLEANING CAUTION WARNING CAUTION your air conditioner occasionally to keep it looking new. Be sure to unplug the unit before cleaning to prevent chock or fire hazards. shock your air conditioner occasionally to keep it looking new. Be sure to unplug the unit before cleaning to prevent chock or fire hazards. ing ing The air filter should be checked at least once a month to see if cleaning is necessary. Trapped The particles in the filter can build up and cause an air should be checked at least once a month accumulation of frost on the cooling coils. to see if cleaning is necessary. Trapped particles Remove the filter by sliding out from the righthand side. of frost on the cooling coils. in can build up and cause an accumulation Push Wash the filter using liquid dishwashing deter- vent handle to Vent Closed position (where gent and warm water. Rinse filter thoroughly. applicable). Open Gently shake excess water from the filter. Be the front panel. Grasp sure the filter is thoroughly dry before replacing. by center and pull up and out. Or, instead of washing you may vacuum the Wash filter clean. the filter using liquid dishwashing detergent Never use hot water over 40 and warm water. Rinse filter 104 F C(104 thoroughly. (40 C) F) to Note: clean the air filter. Never attempt to operate the Gently shake excess water from Be unit without the air filter. sure the is thoroughly dry before replacing. Or, instead of washing you may vacuum the Cabinet ing filter clean. Note: Be sure to unplug the air conditioner to prevent Never use hot water over 40 C(104 F) to cl ean shock or fire hazard. th e ai r fil ter. Never The cabinet and front may attempt to operate the unit be dusted with an oil-free cloth or washed with without the air filter. a a cloth dampened in a solution of warm water a of water Cabinet and mild liquid dishwashing detergent. Rinse ing Be thoroughly and wipe dry. sure to unplug the air conditioner to prevent shock Never use harsh cleaners, wax or polish on the fire hazard. The cabinet and front may be cabinet front. dusted with an oil-free cloth or washed with a Be sure to wring excess water from the cloth before cloth dampened a solution of warm water and wiping around the controls. Excess water in or around mild liquid dishwashing detergent. Rinse thoroughly the controls may cause damage to the air conditioner. and wipe dry. Never Plug in air conditioner. use harsh cleaners, wax or polish on the cabinet front. Be Winter Storage sure to wring excess water from the cloth before wiping If you plan to store the air conditioner during the winter, around the controls. Excess water in or around the remove it carefully from the window according to the controls may cause damage to the air conditioner. Plug installation instructions. Cover it with plastic or return it air conditioner. to the original carton. Winter Storage If you plan to store the air conditioner during the winter, remove it carefully from the window according to the installation instructions. Cover it with plastic or return it to the original carton

16 Owner s Manual Room Conditioner with R-410A Heat Controller, Inc. TROUBLESHOOTING TIPS Before calling for service, review this list. It may save you time and expense. This list includes common occurrences that are not the result of defective workman-ship or materials in this appliance. Problem conditioner does not start Solution Wall plug disconnected. Push plug firmly into wall outlet. House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker. Plug Current Device Tripped. Press the RESET button. Control is OFF. Turn Control ON and set to desired setting. from unit does not feel cold enough O O Room temperature below 17 C(62 F). Cooling may not occur until room temperature 62 F (17 C). O O rises above 17 C(62 F). 62 F (17 C). Temperature sensing element touching cold coil, located behind air filter. Straighten tube away from coil. Reset to a Lower temperature. Compressor shut-off by changing modes. Wait approximately 3 minutes and listen for compressor to restart when set in the COOL mode. conditioner cooling, but room is too warm- ice forming on cooling coil behind decorative front. conditioner cooling, but room is too warm- NO ice forming on cooling coil behind decorative front. O Outdoor temperature below 18 C(64 F). To defrost the coil, set FAN ONLY 64 F O (18 C). mode. filter may be dirty. filter. Refer to Care and ing section. To defrost, set to FAN ONLY mode. Thermostat set too cold for night-time cooling. To defrost the coil, set to FAN ONLY mode. Then, set temperature to a Higher setting. Dirty air filter- air restricted. air filter. Refer to Care and ing section. Temperature is set too High, set temperature to a Lower setting. directional louvers positioned improperly. Position louvers for better air distribution. Front of units is blocked by drapes, blinds, furniture, etc. - restricts air distribution. Clear blockage in front of unit. Doors, windows, registers, etc. Open- cold air escapes. Close doors, windows, registers. Unit recently turned on in hot room. Allow additional time to remove Stored heat from walls, ceiling, floor and furniture. conditioner turns on and off rapidly Noise when unit is cooling Water dripping INSIDE when unit is cooling. Dirty air filter- air restricted. air filter. Outside temperature extremely hot. Set FAN speed to a Higher setting to bring air past cooling coils more frequently. movement sound. This is normal. If too loud, set to a slower FAN setting. Window vibration - poor installation. Refer to installation instructions or check with installer. Improper installation. Tilt air conditioner slightly to the outside to allow water drainage. the rear/outside to allow water drainage. Refer to installation instructions - check with installer

17 Heat Controller, Inc. Room Conditioner with R-410A Owner s Manual Problem Water dripping OUTSIDE when unit is cooling. Remote Sensing Deactivating Prematurely (some models) Room too cold Solution Unit removing large quantity of moisture from humid room. This is normal during excessively humid days. Remote control not located within range. Place remote control within 20 feet & 180, radius of the front of the unit. Remote control signal obstructed. Remove obstruction. Set temperature too low. Increase set temperature

18 Design, material, performance data and components subject to change without notice. HEAT CONTROLLER, INC Wellworth Ave., Jackson, Ml Ph Fax THE QUALITY LEADER IN CONDITIONING AIR 12/2009