Data Storage (Splicing result) Storage Condition

Transcription

1 - 1 -

2

3 Applicable Sleeve Heating Time Standard : 20, 25, 30, 35, 40, 60mm Custom : 4*32mm sleeve (For SOC) 8~900sec (Typical: 18Sec) Heating Cooling Time 0~ 180sec Oven Heat mode Factory pre-set User Edit 9ea 9ea Heating block Standard SOC Customized 1ea(Pre-installed) 1ea(In Package) Applicable Fiber Fiber count : Single core Fiber Type : SM(ITU-TG.652)/ DS(ITU-TG.653)/ NZDS(ITU-TG.655)/ ITU-TG.657 / MM(ITU-TG.651) Fiber count : Single core fber in cable Camera Display Microscope High precision dual camera 4.3 wide color reinforced LCD x150 : X&Y axis dual view x300 : X axis single view x300 : Y axis single view AC 100~240V Applicable Cable Splice Loss Applicable diameter : 0.25mm / 0.9mm / 2.0mm / 2.4mm / 3.0mm Applicable buffer Diameter : Cladding diameter : 80~150µm, Coating diameter : 100~3,000 µm SM : 0.02dB MM : 0.01dB DS : 0.04dB NZDS : 0.04dB Power Supply Splicer 50~60HZ DC9~14V G.657 : 0.02dB Altitude 0~5,000M Data Capacity Li-ion Battery DC 11.1V Factory pre-set Splice Mode User Edit 33ea 34ea Reliability Operating Condition Humidity 0~95% Temperature -15~60 Wind Speed 15m/s Splice Speed Data Storage (Splicing result) SM FAST mode SM AUTO mode 7 Sec. 9 Sec. 3,000ea Storage Condition Humidity 0~95% Splicer -40~80 Temperature Battery -20~

4

5 Select Splice Mode Edit Splice Mode Factory Pre-set : 33ea User edit : 33ea Custom build splice mode : 1ea Delete Splice Mode

6 Auto Start ON : Automatic splicing procedure OFF : Maunal Splicing procedure Select Heater Mode Edit Heater Mode Factory Pre-set : 9ea User edit : 9ea Custom build splice mode : 1ea Pause 1 Pause 2 Realign After Pause 2 Ignore Splicing Error Fiber Image On Screen ON : Pause after the fiber gap position process OFF : Proceeding without the pause ON : Pause after camera focus & Axis alignment process OFF : Proceeding without the pause ON : Automatically proceed realignment OFF : Proceeding without the pause splicng error message is not displayed Select display structure for each splicing process Delete Heater Mode

7 Display Splice Record Displaying your detailed splice record Delete Splice Record - Export Splice Data Splice Data Save Downloading saved data (Splice record or Image) ON : Automatic data save * Image data is saved manually * OFF : Do not save splice record Splice Mode Lock Heater Mode Lock Recordes Delete Lock Password Lock ON : Disable Splice mode edit OFF : Ensable Splice mode edit ON : Disable Heater mode edit OFF : Enable Heater mode edit ON : Disable Record mode edit OFF : Enable Heater mode edit ON : Disable to change the password OFF : Enable to change the password

8 LED Calibration Dust Check Motor Calibration Arc Calibration Measures and adjusts the brightness of LED Dust checking process Automatically calibrates the motor speed Automatically calibrates the Arc power

9 1 Prepare the USB device. 2 Download the latest version software to the USB. 3 Link to the Splicer (Via link cable in the package). 4 Press O Button to proceed update. 5 Device will be rebooted once it is done. Electrode Caution Electrode Warning Caution alram will be displayed when it reachs the number of splicing cycle you set Caution alram will be displayed when it reachs the number of splicing cycle you set

10 Buzzer ON : Sound on OFF : Sound off 繁 体 中 文 Language Available Việt Temperature Unit : Celcisius : Fahrenheit English العربية Automatic Heating Monitor Position ON : Auto start OFF : Manual start Front : Normal direction display Rear : Opposite direction display 한글 Русский Deutsch Español Italiano Português Dust Check Password Lock ON : Check the dust density OFF : Skip dust checking process ON : Password is required to operate the device OFF : No passwerd is required Français ไทย فارسی Pull Test ON : Automatic pull test processing after splicing OFF : Skip pull test process

11 Monitor Shut Down Splicer Shut Down 1) No input during the time you set, the splicer will block the power supply toward LCD 2) System will be switched over to standby mode. Press the power button to resume (Screen will be back on) No input during the time you set, the splicer will be shut down to save the power Pressing the power cutton for 2sec, to reboot the splicer 1 Input 4-digit old password number 2 Input new 4-digit number for new password

12 Machine Serial No. Software Version FPGA Total Arc Count Current Arc Count Last Maintenance Production Date Sales Region Product OEM Identification number of the splicer Software version being installed Field programmable gate array version Total number of Arc discharges Current number of Arc discharge Last maintenance date Manufacturing date Authorised country for sales Manufacturer name

13 Fat Fiber stuffing too much Decrease [Overlap] and perform [Motor clibration] Symptom Name Reason Solution Core Axial Offset Core Angle Dust on v-groove or fiber clamp chip Dust on v-groove or fiber clamp chip Bad fiber end-face quality Clean v-groove and fiber clamp chip Clean v-groove and fiber clamp chip Check if fiber cleaver is well conditioned Thin Line Arc power not adequate Some arc parameters not adequate Some arc parameters not adequate Perform [Arc calibration] Adjust [Prefuse power], [Pre-fuse time] or [Overlap] Adjust [Prefuse power], [Pre-fuse time] or [Overlap] Core Step Core Curve MFD Mismatch Dust on v-groove of fiber clamp chip Bad fiber end-face quality Pre-fuse power too low or pre-fuse time too short Arc power too low Clean v-groove and fiber clamp chip Check if fiber cleaver is well conditioned INcrease [Pre-fuse power] and/or [Pre-fuse time] Increase [Arc power] Combution Bubbles Separation Bad fiber end-face quality Dust still present after cleaning fiber of cleaning arc Bad fiber end-face quality Pre-fuse power too low or pre-fuse time too short Fiber stuffing too small Pre-fuse power too high of pre-fuse time too long Check the cleaver Clean fiber throughly or increase [Cleaning arc time] Check if fiber cleaver is well conditioned Pre-fuse power too low or pre-fuse time too short Perform [Motor calibration] Decrease [Pre-fuse power] and/or [Pre-fuse time]

14 Unidentified Type of Fibers Shock occurred to the splicer during the splicing process Execute Motor Clibration If the [problem still exist, please contact the sale agent Error Message Reason Solution L Fiber Place Error R Fiber Place Error Propulsion Motor Overrun The fiber end-face is placed on the electrode centerline, or beyond it The fiber is no set correctly at the bottom of the V-groove, which results in that the fiber offsets beyond motor formation range Press the Reset Button. Reload the fibers, make sure fiber end face between V-groove and the centre position of electrodes Press the Reset button and then re-position the fiber at the bottom of the V-groove Contact of Fiber End-faces Focus Motor Overrun Overlap too much Motor is not calibrated The fiber is misplaced There s dust of dirt on the fiber surface There s dust of dirt on the fiber surface Adjust overlap parameter Calibrate and maintain the motor Press the Reset vutton and then reposition the fiber correctly Prepare the fiber again Execute the [Dust check] after the lenses and LEDs are cleaned Propulsion Motor Trouble Failed to Find The Fiber End-face No Arc Discharge Motor Overrun Cannot Find the Edge of The Cladding Find Wrong Fiber Edges Motor might be damaged The fiber is not set correctly at the bottom of the V-groove Arc Discharge does not occur The fiber is not set correctly at the bottom of the V-groove The fiber is not set correctly at the bottom of the V-groove There s dust on the fiber suface Consult your nearest sales agency Press the Reset button and then re-position the fiber correctly at the bottom of the V-groove Confirm the electrodes in proper position; Replace electrodes Press the Reset button and then re-position the fiber at the bottom of the V-groove Press the Reset button and then re-position the fiber at the bottom of the V-groove Re-prepare the fiber; Clean the lens and protector mirror and then redo Dust Check Fibers Mismatch Large Cleave Angle Large Core Angle The fibers of two sides are different type Bad fiber end-face [Cleave Limit] is set too low [Core angle limit] is set too low Dust of dirt is on the V-groove or hte clamp chip It may resul tin large splice loss if you continue to splice, Please use the proper splice mode corresponding to the fibers check the condition of the fiber cleaver, if the blade is worn, rotate the blade to a new position or change a new one, and then re-prepare the fibers Increase the [Cleave limit] to an adequate limit(standard:3.0 c) Increase the [Core angle limit] to an adequate limit (standard:1.0 c) Clean V-groove and clamp chip. Prepare the fibers and re-load them Unidentified Type of Fiber Shock occurred to the splicer during the splicing process Execute Motor Calibration If the [problem stillexist, please contact the sale agent Focus Error Too large axial offset(>0.4um)w The motor is not calibrated Re-prepare the fibers Execute [Motor clibration]

15 Dust Error (fiber core) Fat Fiber Thin Fiber There s dust or dirt on the fiber surface The lens or LEDs are coated in dust Cleaning Arc time is too short It is difficult to identify the fiber core by using the method of core alignment to splice There s dust or dirt on the fiber surface There s dust or dirt on the fiber surface Cleave angle limit is too low Overlap too much Motor is not calibrated Arc power too low The level of pre-discharge is too high Insufficient overlap Prepare the fiber again Execute the dust check after cleaning the lenses and LEDs Set the cleaning arc time to be 180ms It is difficult to identify the fiber core by using MM splice mode to splice Prepare the fiber again Execute the [Dust check] after the lenses and LEDs are cleaned Increase the cleave angle limit to a decent value (standard value: 3.0 c) Adjust overlap parameter Calibrate and maintain the motor Execute [Arc Calibration] Decreased pre-discharge of pre-discharge time Adjust overlap parameter

16

17