MODEL NO. : LTN156AT05-301

Transcription

1 TO DATE May 4, 29 SAMSUNG SAMSUNG TFTLCD TFTLCD MODEL NO. LTN56AT53 NOTE Extension code [ 3 ] LTN56AT53 Surface type [ Anti Glare ] Any Modification of Spec is not allowed without SEC permission. APPROVED BY PREPARED BY Technical Customer Support Team, LCD Division Samsung Electronics Co., Ltd. Doc.No. LTN56AT53 Rev.No 4AG954 Page / 3

2 CONTENTS Revision History General Description. Absolute Maximum Ratings. Absolute Ratings of environment.2 Electrical Absolute Ratings 2. Optical Characteristics 3. Electrical Characteristics 3. TFT LCD Module 3.2 Backlight Unit 3.3 LED Driver 4. Block Diagram 4. TFT LCD Module ( 3 ) ( 4 ) ( 5 ) ( 7 ) ( ) ( 3 ) 5. Input Terminal Pin Assignment ( 4 ) 5. Input terminal pin assignment 5.2 LVDS Interface 5.3 Timing Diagrams of LVDS For Transmitting 5.4 Input Signals, Basic Display Colors and Gray Scale of Each Color. 5.5 Pixel format 6. Interface Timing 6. Timing Parameters 6.2 Timing Diagrams of interface Signal 6.3 Power ON/OFF Sequence 7. Outline Dimension 8. Packing 9. Markings & Others. General Precautions. EDID ( 9 ) ( 2 ) ( 23 ) ( 24 ) ( 26 ) ( 28 ) Doc.No. LTN56AT53 Rev.No 4AG954 Page 2 / 3

3 REVISION REVISION HISTORY HISTORY Date Revision No. Page Summary May A All The approval specification of LTN56AT53 model was issued first. Doc.No. LTN56AT53 Rev.No 4AG954 Page 3 / 3

4 GENERAL DESCRIPTION DESCRIPTION LTN56AT5 is a color active matrix TFT (Thin Film Transistor) liquid crystal display (LCD) that uses amorphous silicon TFT as switching devices. This model is composed of a TFT LCD panel, a driver circuit and a backlight unit. The resolution of a 5.6" contains 366 x 768 pixels and can display up to 262,44 colors. 6 O'clock direction is the optimum viewing angle. FEATURES High contrast ratio HD (366 x 768 pixels ) resolution High Color Gamut (Typical 6%) Low power consumption Fast response time LED Back Light with embedded LED Driver DE (Data enable) only mode 3.3V LVDS Interface Onboard EEDID chip Green product (RoHS compliance) APPLICATIONS Notebook PC If the usage of this product is not for PC application, but for others, please contact SEC GENERAL INFORMATION Item Specification Unit Note Display area (H) x (V) ( 5.6 HD diagonal ) mm Driver element asi TFT active matrix Display colors 262,44 Number of pixel 366 x 768 pixel 69 Pixel arrangement RGB vertical stripe Pixel pitch.252(h) x.252(v) (TYP.) mm Display Mode Normally white Surface treatment Haze 25%, HardCoating 3H Doc.No. LTN56AT53 Rev.No 4AG954 Page 4 / 3

5 Mechanical Information Item Min. Typ. Max. Unit Note Module size Horizontal (H) Vertical (V) Depth (D) mm mm mm () Weight g Note () Measurement condition of outline dimension. Equipment Bernier Calipers. Push Force 5g f (minimum). ABSOLUTE MAXIMUM RATINGS. ENVIRONMENTAL ABSOLUTE RATINGS Item Symbol Min. Max. Unit Note Storage temperate TSTG 2 6 C () Operating temperate (Temperature of glass surface) TOPR 5 C () Shock ( nonoperating ) Snop 24 G (2),(4) Vibration (nonoperating) Vnop 2.4 G (3),(4) Note () Temperature and relative humidity range are shown in the figure below. 95 % RH Max. (4 C Ta) Maximum wet bulb temperature at 39 O C or less. (Ta > 4 C ) No condensation 9 Relative Humidity ( %RH) ( 4,9 ) 8 (2) 2ms, half sine wave, one time for ±X, ±Y, ± Z. (3) 5 5 Hz, random vibration, 3min for X, Y, Z. (4) At testing Vibration and Shock, the fixture in holding the Module to be tested have to be hard and rigid enough so that the Module would not be twisted or bent by the fixture Operating Range Storage Range Temperature ( O C) ( 5,5.4 ) ( 6,27.7 ) Doc.No. LTN56AT53 Rev.No 4AG954 Page 5 / 3

6 .2 ELECTRICAL ABSOLUTE RATINGS () TFT LCD MODULE VDD =3.3V, VSS = GND = V Item Symbol Min. Max. Unit Note Power Supply Voltage VDD VDD.3 VDD +.3 V () Logic Input Voltage VIN VDD.3 VDD +.3 V () Note () Within Ta (25 ± 2 C ) Doc.No. LTN56AT53 Rev.No 4AG954 Page 6 / 3

7 2. OPTICAL CHARACTERISTICS The following items are measured under stable conditions. The optical characteristics should be measured in a dark room or equivalent state with the methods shown in Note (5). Measuring equipment TOPCON SR3 * Ta = 25 ± 2 C, VDD=3.3V, fv= 6Hz, fdclk = 69.3MHz, IF = 2 ma Item Symbol Condition Min. Typ. Max Unit Note Contrast Ratio (5 Points) CR 3 (), (2), (5) Response Time at Ta ( Rising + Falling ) TRT 6 25 msec (), (3) Average Luminance of White (5 Points) YL,AVE 7 2 cd/m 2 IF=2mA (), (4) Color Chromaticity ( CIE ) Red Green Blue RX RY GX GY BX BY Normal Viewing Angle φ = θ = (), (5) SR3 White WX WY Viewing Angle Hor. Ver. θl θh φh CR At center Degrees (), (5) SR3 φl Points White Variation δl.4.6 (6) Doc.No. LTN56AT53 Rev.No 4AG954 Page 7 / 3

8 Note ) Definition of Viewing Angle Viewing angle range( C/R) Normal Line φ = o, θ = o θ L θ R θ L =9 o x φ L φ H y 2 O clock direction φ H = 9 o 6 O clock direction φ L = 9 o y' x' θ R =9 o Note 2) Definition of Contrast Ratio (CR) Ratio of gray max (Gmax),gray min (Gmin) at 5 points(4, 5, 7, 9, ) CR = CR(4) + CR(5) + CR(7) + CR(9) + CR() 5 Points 4, 5, 7, 9, at the figure of Note (6). Note 3) Definition of Response time Display data White(TFT OFF) Black(TFT ON) White(TFT OFF) Optical Response % 9% % % TR TF Time Note 4) Definition of Average Luminance of White measure the luminance of white at 5 points. Average Luminance of White ( YL,AVE ) VIEW AREA 92 YL,AVE = YL4 + YL5 + YL7 + YL9 + YL (lines) test point Doc.No. LTN56AT53 Rev.No 4AG954 Page 8 / 3

9 Note 5) After stabilizing and leaving the panel alone at a given temperature for 3 min, the measurement should be executed. Measurement should be executed in a stable, windless,and dark room. 3 min after lighting the backlight. This should be measured in the center of screen. IF current 2.mA Environment condition Ta = 25 ± 2 C Photodetector ( TOPCON SR3 ) Field = 2 5 cm TFTLCD module LCD panel Center of the screen [ Optical characteristics measurement setup ] Note 6) Definition of 3 points white variation (δ L ), CR variation( CVER ) [ ~ ] 3 δ L = Maximum luminance of 3 points Minimum luminance of 3 points mm mm mm test point mm (lines) Doc.No. LTN56AT53 Rev.No 4AG954 Page 9 / 3

10 3. ELECTRICAL CHARACTERISTICS 3. TFT LCD MODULE Ta= 25 ± 2 C Item Symbol Min. Typ. Max. Unit Note Voltage of Power Supply VDD V Differential Input Voltage for LVDS Receiver Threshold High Low VIH VIL + mv mv VCM = +.2V Vsync Frequency fv 6 Hz Hsync Frequency fh 46.8 KHz Main Frequency fdclk MHz Rush Current IRUSH.5 A (4) White 33 ma (2),(3)*a Current of Power Supply Mosaic IDD 47 ma (2),(3)*b V. stripe 5 6 ma (2),(3)*c Note () Display data pins and timing signal pins should be connected.( GND = V ) (2) fv = 6Hz, fdclk = 69.3MHZ, VDD = 3.3V, DC Current. (3) Power dissipation pattern *a) White Pattern *b) Mosaic Pattern VIEW AREA Display Brightest Gray Level Display Darkest Gray Level Doc.No. LTN56AT53 Rev.No 4AG954 Page / 3

11 *c) dot Vertical stripe pattern R G B R G B R G B R G R G B R G B R G B R G R G B R G B R G B R G R G B R G B R G B R G 4) Rush current measurement condition 3.3V R 47K M 2SK59 FUSE C uf VDD ( LCD INPUT) CONTROL SIGNAL (HIGH to LOW) R2 K M2 2SK399 2V R3 C2 C3 uf 47K pf VDD rising time is 47us.9VDD 3.3V GND.VDD 47us Doc.No. LTN56AT53 Rev.No 4AG954 Page / 3

12 3.2 BACKLIGHT UNIT Ta= 25 ± 2 C Item Symbol Min. Typ. Max. Unit Note LED Forward Current IF ma LED Forward Voltage VF 3.2 V LED Array Voltage VP V VF x LEDs Power Consumption P 4. W w/ Driver Operating Life Time Hr 2, Hour () Note () Life time (Hr) of LEDs can be defined as the time in which it continues to operate under the condition Ta= 25 ± 2 C and IF = 2. marms until one of the following event occurs.. When the brightness becomes 5% or lower than the original. 3.3 LED Driver Ta= 25 ± 2 C Item Symbol Min. Typ. Max. Unit Note Input Voltage Vin V Enable Control Level V 5 V ON Level 2V~5V OFF Level V ~.5V PWM Control Level VPWM 5 V High Level 2.7V~5V Low Level V ~.3V PWM Control Duty Ratio % % PWM Input Frequency BLIM.2 KHz Note Test Equipment Fluke 45 Doc.No. LTN56AT53 Rev.No 4AG954 Page 2 / 3

13 4. BLOCK DIAGRAM 4. TFT LCD Module Input Connector IPEX 24554E or Compatible I 2 C bus LVDS EDID EEPROM LVDS Input/mLVDS Output Timing Controller mlvds Source Driver IC 5.6 HD TFTLCD Panel LED Controller DCDC Converter Gamma Generator LED B/L VCOM Generator SOURCE PCB TFT on Glass Video Signal Control Signal VCOM LED Power&signal DVDD AVDD Von/Voff Gamma Feedback 4.2 LED connection and placement Doc.No. LTN56AT53 Rev.No 4AG954 Page 3 / 3

14 5. INPUT TERMINAL PIN ASSIGNMENT 5.. Input terminal pin assignment (LVDS, Connector 24554E by IPEX or equivalent ) No. Signal Description 2~ ~ ~ ~ ~3 3~ ~4 NC AVDD DVDD NC SCL SDA Rin Rin+ GND Rin Rin+ GND Rin2 Rin2+ GND ClkIN ClkIN+ GND NC GND NC GND NC GND NC VBL NC BLIM BL_Enable NC VBL+ No Connection Power Supply, 3.3V ( typical) DDC 3.3V power No Connection DDC Clock DDC Data LVDS differential data input (RR5, G) +LVDS differential data input (RR5, G) Ground LVDS differential data input (GG5, BB) +LVDS differential data input (GG5, BB) Ground LVDS differential data input (B2B5, HS, VS, DE) +LVDS differential data input (B2B5, HS, VS, DE) Ground LVDS differential clock input +LVDS differential clock input Ground No Connection Ground No Connection Ground No Connection Ground No Connection LED Ground No Connection PWM for luminance control (2~KHz, 3.3V, ~%) BL On/Off (On2.~3.3V, Off ~.5V) No Connection LED Power Supply 6V~2V Doc.No. LTN56AT53 Rev.No 4AG954 Page 4 / 3

15 5.2 LVDS Interface Transmitter SN75LVDS86 or Compatible Pin No. Name RGB Signal Pin No. Name RGB Signal 44 TxIN R 2 TxIN G5 45 TxIN R 3 TxIN2 B 47 TxIN2 R2 5 TxIN3 B 48 TxIN3 R3 6 TxIN4 B2 TxIN4 R4 8 TxIN5 B3 3 TxIN5 R5 9 TxIN6 B4 4 TxIN6 G 2 TxIN7 B5 6 TxIN7 G 22 TxIN8 Hsync 7 TxIN8 G2 23 TxIN9 Vsync 9 TxIN9 G3 25 TxIN2 DE TxIN G4 26 TxCLKIN Clock LVDS INTERFACE Graphics controller 8bit RED RED RED2 RED3 RED4 RED5 GREEN GREEN GREEN2 GREEN3 GREEN4 GREEN5 BLUE BLUE BLUE2 BLUE3 BLUE4 BLUE5 Hsync Vsync Enable CLOCK SN75LVDS86 TxIN TxIN TxIN2 TxIN3 TxIN4 TxIN5 TxIN6 TxIN7 TxIN8 TxIN9 TxIN TxIN TxIN2 TxIN3 TxIN4 TxIN5 TxIN6 TxIN7 TxIN8 TxIN9 TxIN2 TxClkIN TxOUT+ TxOUT+ TxOUT2+ LVDS+I/F IC RxIN RxIN+ RxIN RxIN+ RxIN2 RxIN2+ RxCLKIN RxCLKIN+ TxOUT TxOUT TxOUT2 TxCLKOUT TxCLKOUT+ IPEX 24554E 3 5 Ω Ω Ω Ω 5 Note ) The LCD Module uses a ohm resistor between positive and negative lines of each receiver input. Doc.No. LTN56AT53 Rev.No 4AG954 Page 5 / 3

16 5.3 Timing Diagrams of LVDS For Transmission LVDS Receiver Integrated TCON TxCLK OUT RxCLK IN T T/7 Rx IN2 RxOUT2 RxOUT9 RxOUT8 RxOUT7 RxOUT6 RxOUT5 RxOUT4 DE Vsync Hsync B5 B4 B3 B2 Rx IN RxOUT3 RxOUT2 RxOUT RxOUT RxOUT9 RxOUT8 RxOUT7 B B G5 G4 G3 G2 G RxIN RxOUT6 RxOUT5 RxOUT4 RxOUT3 RxOUT2 RxOUT RxOUT G R5 R4 R3 R2 R R Doc.No. LTN56AT53 Rev.No 4AG954 Page 6 / 3

17 Doc.No. Rev.No Page / 3 LTN56AT53 7 4AG Input Signals, Basic Display Colors and Gray Scale of Each Color Note ) Definition of gray Rn Red gray, Gn Green gray, Bn Blue gray (n=gray level) Note 2) Input signal =Low level voltage, =High level voltage B3 B6 B2 B Dark B Black Gray Scale Of Blue G6 G3 G6 G2 G Dark G Black Gray Scale Of Green B63 Blue B62 Light B6 G63 Green G62 Light R63 Red R62 Light R6 R3 R6 R2 R Dark R Black Gray Scale Of Red White Yellow Magenta Red Cyan Green Blue Black Basic Colors B5 45 B3 B2 B B G5 G4 G3 G2 G G R5 R4 R3 R2 R R Blue Green Red Gray Scale Level Data Signal Display Color

18 5.5 Pixel Format in the display 366 Line R G B R G B R G B R G B LTN56AT5 Panel Line 768 R G B R G B R G B R G B Doc.No. LTN56AT53 Rev.No 4AG954 Page 8 / 3

19 6. INTERFACE TIMING 6. Timing Parameters Signal Item Symbol Min. Typ. Max. Unit Note Frame Frequency Cycle TV Lines Vertical Active Display Term Display Period TVD 768 Lines One Line Scanning Time Cycle TH Clocks Horizontal Active Display Term Display Period THD 366 Clocks 6.2 Timing diagrams of interface signal TV TVD DE TH DCLK TC THD DE DATA SIGNALS Valid display data ( 366 clocks) Doc.No. LTN56AT53 Rev.No 4AG954 Page 9 / 3

20 6.3 Power ON/OFF Sequence To prevent a latchup or DC operation of the LCD module, the power on/off sequence should be as the diagram below..9 V DD.9 V DD Power Supply VDD V. V DD. V DD T T 7 T 4 T 2 T 3 Signals V VALID T 8 T 9 T T LED Power (V in ). V in.9 V in.9 V in. V in V T 2 T 3 PWM V T 4 T 5 B/L Enable V T 5 T 6 Timing (ms) Remarks.5<T <T 2 5 <T T 4 2 T 5 2 T 6 <T 7 <T 8 <T 9.5<T.5<T Delay from LED driver Vin rising time 9% to PWM ON <T 2 Delay from PWM Off to LED driver Vin falling time % <T 3 V DD rising time from % to 9% Delay from V DD to valid data at power ON Delay from valid data OFF to V DD OFF at power Off V DD OFF time for Windows restart Delay from valid data to B/L enable at power ON Delay from valid data off to B/L disable at power Off V DD falling time from 9% to % Delay from valid data on to LED driver Vin rising time % Delay from LED driver Vin falling time % to valid data Off LED V in rising time from % to 9% LED V in falling time from 9% to % <T 4 <T 5 Delay from PWM ON to B/L Enable ON Delay from B/L Enable Off to PWM Off Note Backlight may flash if interface signal remains floating state at invalid period. Doc.No. LTN56AT53 Rev.No 4AG954 Page 2 / 3

21 7. Mechanical Outline Dimension Refer to the next page Doc.No. LTN56AT53 Rev.No 4AG954 Page 2 / 3

22

23 8. PACKING. CARTON(Internal Package) () Packing Form Corrugated Cardboard box and Corrupad form as shock absorber (2) Packing Method CUSHION BOTTOM PANEL 2EA/SLIT CUSHION TOP, BOTTOM Note () Total Approx. 24g (2) Acceptance number of piling 2 sets (3) Carton size 344(W) X 432(D) X 329(H) Doc.No. LTN56AT53 Rev.No 4AG954 Page 23 / 3

24 (3)Packing Material No Part name Static electric protective sack Quantity Packing case (Inner box) included shock absorber Pictorial marking Carton set 2 pcs set 9. MARKINGS & OTHERS A nameplate bearing followed by is affixed to a shipped product at the specified location on each product. ()Parts number LTN56AT5 (2)Revision code 3 letters (3)Lot number X X X X XXX XX X 3 SEC Revision Code Panel number Cell ID Lot ID Month Year Product Code Line (4) Nameplate Indication 843 LTN56AT5 XXXXXXXXXX 3 CT XXXXXXXXXXXXXX 4 mm MADE IN CHINA 8 mm Parts name LTN56AT5 Lot number XXXXXXXXXX Inspected work week 843 (28 year 43rd week) Product Revision Code 3 CT code XXXXXXXXXXXXXX (Released after HP s approval) Doc.No. LTN56AT53 Rev.No 4AG954 Page 24 / 3

25 (5) High voltage caution notice HIGH VOLTAGE CAUTION RISK OF ELECTRIC SHOCK DISCONNECT THE ELECTRIC POWER BEFORE SERVICE THIS COVER CONTAINS FLUORESCENT LAMP. PLEASE FOLLOW LOCAL ORDINANCES OR REGULATIONS FOR ITS DISPOSAL mm 7mm (6) Packing small box attach DEVICE LTN56AT5 TYPE 3 QTY PCS XXXXXXXXXX MADE IN CHINA (7) Packing box Marking Samsung TFTLCD Brand Name Doc.No. LTN56AT53 Rev.No 4AG954 Page 25 / 3

26 . GENERAL PRECAUTIONS. Handling (a) When the module is assembled, It should be attached to the system firmly using every mounting holes. Be careful not to twist and bend the modules. (b) Refrain from strong mechanical shock and / or any force to the module. In addition to damage, this may cause improper operation or damage to the module and CCFT backlight. (c) Note that polarizers are very fragile and could be easily damaged. Do not press or scratch the surface harder than a HB pencil lead. (d) Wipe off water droplets or oil immediately. If you leave the droplets for a long time, Staining and discoloration may occur. (e) If the surface of the polarizer is dirty, clean it using some absorbent cotton or soft cloth. (f) The desirable cleaners are water, IPA (Isoprophyl Alcohol) or Hexane. Do not use Ketone type materials(ex. Acetone), Ethyl alcohol, Toluene, Ethyl acid or Methyl chloride. It might permanent damage to the polarizer due to chemical reaction. (g) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In case of contact with hands, legs or clothes, it must be washed away thoroughly with soap. (h) Protect the module from static, it may cause damage to the CMOS Gate Array IC. (i) Use fingerstalls with soft gloves in order to keep display clean during the incoming inspection and assembly process. (j) Do not disassemble the module. (k) Do not pull or fold the lamp wire. (l) Do not adjust the variable resistor which is located on the back side. (m) Protection film for polarizer on the module shall be slowly peeled off just before use so that the electrostatic charge can be minimized. (n) Pins of I/F connector shall not be touched directly with bare hands. Doc.No. LTN56AT53 Rev.No 4AG954 Page 26 / 3

27 2. STORAGE (a) Do not leave the module in high temperature, and high humidity for a long time. It is highly recommended to store the module with temperature from to 35 C and relative humidity of less than 7%. (b) Do not store the TFTLCD module in direct sunlight. (c) The module shall be stored in a dark place. It is prohibited to apply sunlight or fluorescent light during the store. 3. OPERATION (a) Do not connect,disconnect the module in the Power On condition. (b) Power supply should always be turned on/off by following item 6.3 Power on/off sequence. (c) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be done by system manufacturers. Grounding and shielding methods may be important to minimize the interference. (d) The standard limited warranty is only applicable when the module is used for general notebook applications. If used for purposes other than as specified, SEC is not to be held reliable for the defective operations. It is strongly recommended to contact SEC to find out fitness for a particular purpose. 4. OTHERS (a) Ultraviolet ray filter is necessary for outdoor operation. (b) Avoid condensation of water. It may result in improper operation or disconnection of electrode. (c) Do not exceed the absolute maximum rating value. ( the supply voltage variation, input voltage variation, variation in part contents and environmental temperature, so on) Otherwise the module may be damaged. (d) If the module displays the same pattern continuously for a long period of time,it can be the situation when the image sticks to the screen. (e) This module has its circuitry PCB s on the rear side and should be handled carefully in order not to be stressed. Doc.No. LTN56AT53 Rev.No 4AG954 Page 27 / 3

28 . EDID Address Value ASCII (HEX) HEX Data FF FF FF 255 Header 4 FF FF FF C 76 S ID Manufacturer Name E 9 A3 63 C A 5 8 [Q] ID Product Code B [5] C D 32bit serial no. E F Week of manufacture Year of manufacture EDID Structure Ver. 3 EDID revision # Video input definition Max H image size Max V image size Display Gamma Feature support A 9 Red/green low bits A B Blue/white low bits Red x/ high bits F C Red y 57 D Green x 4F E FUNCTION BIN Green y 8C F Blue x 27 2 Blue y 27 2 White x 5 22 White y Established timing 24 Established timing 2 25 Established timing 3 DEC or EDID Header 3 character ID "SEC" 28 EDID Ver.. EDID Rev cm(approx) 9 cm(approx) Gamma 2.2 Red x.58= Red y.34= Green x.3= Green y.55= Blue x.55= Blue y.55= White x.33= White y.329= Notes Doc.No. LTN56AT53 Rev.No 4AG954 Page 28 / 3

29 26 Standard timing # Standard timing #2 29 2A Standard timing #3 2B 2C Standard timing #4 2D 2E Standard timing #5 2F 3 Standard timing # Standard timing # Standard timing # B A 5 8 3B 768 3C C 2 2 3D E F Detailed timing/monitor descriptor # not used not used not used not used not used not used not used not used Main clock= 69.3 MHz Hor active=366 pixels Hor blanking=4 pixels 4bit 4bit Vertcal active=768 lines Vertical blanking=2 lines 4bit 4bit H sync. Offset=48 pixels H sync. Width=32 pixels V sync. Offset=2 lines V sync. Width=5 lines 4 2bit 2bit 2bit 2bit C A 4B F 5 4C 4D 4E 4F Detailed timing/monitor 5 descriptor # E 3 56 B Tvpmax=value*2 + VA lines 59 Module revision H image size= 344 mm(approx) V image size = 94 mm(approx) No Horizontal Border No Vertical Border Manufacturer Specified (Timing) Value=HSPWmin / 2 Value=HSPWmax / 2 Value=Thbpmin /2 Value=Thbpmax /2 Value=VSPWmin /2 Value=VSPWmax /2 Value=Tvbpmin / 2 Value=Tvbpmax / 2 Thpmin=value*2 + HA pixelclks Thpmax=value*2 + HA pixelclks Tvpmin=value*2 + VA lines Doc.No. LTN56AT53 Rev.No 4AG954 Page 29 / 3

30 5A 5B 5C 5D FE 254 5E 5F [S] [A] 6 Detailed timing/monitor 4D 77 [M] 62 descriptor # [S] [U] 64 4E 78 [N] [G] 66 A [^] [ ] [ ] [ ] 6A 2 32 [ ] 6B 2 32 [ ] 6C 6D 6E 6F FE [] [5] 73 Detailed timing/monitor [6] 74 descriptor # [A] [T] [] [5] 78 2D 45 [] [3] 7A 3 48 [] 7B 3 49 [] 7C A [^] 7D 2 32 [ ] 7E Extension Flag 7F Checksum 2B 43 ASCII Data String Tag Monitor Name Tag (ASCII) Doc.No. LTN56AT53 Rev.No 4AG954 Page 3 / 3