Active Directory Integration
|
|
|
- Erick Powell
- 8 years ago
- Views:
Transcription
1 SwiftStack Gateway Active Directory Integration Summary There are two main ways of integrating the SwiftStack Gateway with Microsoft Active Directory authentication: RID, using winbind LDAP For most implementations using the RID method will typically work best, as it should work across all versions of Windows Server and Active Directory. For older versions of Windows, before Windows 2012 R2, and in cases where AD is also integrated into standard LDAP, it's also possible to use LDAP authentication. The following sections assume that you've already set up and configured a basic functioning gateway and created a CIFS/SMB share. If you haven't done so, please go ahead and install, claim and configure a gateway before proceeding with the Active Directory integration steps below. Prerequisites SELinux SELinux is currently not supported on the SwiftStack Gateway and therefore needs to be turned off. Red Hat and CentOS both have SELinux turned on and set to 'enforce' by default. To check the status of SELinux on your Gateway node, you can run: $ sestatus To turn SELinux off, you can edit the file /etc/selinux/config and replace 'enforce' with 'disabled'. For the change to take effect, you need to reboot your Gateway. Page 1 of 6
2 Active Directory with RID (winbind) The SwiftStack Gateway can use Samba and winbind to query Windows RID accounts. This is the preferred way of integrating the SwiftStack Gateway with an Active Directory environment. For the integration to work, the Gateway needs to be joined to the Windows domain using an account belonging to the Windows Administrators group on the domain. Gateway AD Domain Configuration Before joining the Gateway to the domain you first need to configure the Active Directory settings in the SwiftStack Controller web UI. Go to the Manage page for the Gateway. On the left menu, click on the Auth tab. Click on the 'CIFS' (Active Directory) section to reveal the settings available. Fill out the FQDN or IP address of your primarily AD server. Some older versions of Windows may be case sensitive when it comes to the Windows domain name, so be sure to put in your domain name correctly. Once you've filled out the correct settings for your domain, click on 'Submit' at the bottom of the page. Finally, after submitting the changes, you also need to push the AD configuration to the Gateway for the changes to take effect. Joining The Gateway To The Domain After the configuration push has completed, you must join the Gateway server to the domain. Joining the domain from the Gateway must currently be done from the command line. To join the Gateway to the domain run the following command: $ sudo ad_join -r <ad-server-fqdn> -d <username> -p <password> Testing That Everything Works When the Gateway has been successfully joined to the domain, everything should work. You can test that the Gateway can indeed see accounts and groups on the domain and verify that it can authenticate properly. Except for simply testing file share access from a Windows account on the domain, you might want to run a set of diagnostics command on the Gateway to ensure it can see accounts and groups on the Windows domain: Query domain users: $ wbinfo -u Query domain groups: Page 2 of 6
3 $ wbinfo -g Also make sure the Gateway can authenticate users on the AD domain: $ getent passwd If all the above works properly, move on to functionally test that clients can see and interact with the Windows (SMB/CIFS) shares you've created on the Gateway. Gateway CIFS Settings with RID Below are examples from the CIFS settings page required to use Windows RID authentication with the SwiftStack Gateway. Setting CIFS workgroup CIFS case sensitive AD enabled CIFS realm Kerberos admin server CIFS browser announce CIFS id mapping CIFS id range min CIFS id range max Value DOMAIN <as needed> Checked DOMAIN.COM IP or FQDN (default) rid Page 3 of 6
4 Active Directory with LDAP Microsoft s Active Directory is based on a Microsoft version of LDAP, and thus, it s possible to integrate the SwiftStack Gateway using LDAP too. However, using Active Directory LDAP integration requires that ID Management for Unix (IDmU) tools to be installed on the Active Directory server. IDmU has been deprecated in Windows 2012 R2 and it is therefore not recommended to install IDmU on Windows 2012 R2 (or newer). Consequently, if you are integrating with a Windows 2012 R2 based domain controller, you should use the Active Directory with RID (winbind) section above. Gateway CIFS Settings with LDAP Below are examples of the settings required to use LDAP authentication with the SwiftStack Gateway. Note that if using AD/LDAP integration, it is also required to configure the LDAP schema on the LDAP settings page. CIFS Setting CIFS workgroup CIFS case sensitive AD enabled CIFS realm Kerberos admin server CIFS browser announce CIFS id mapping CIFS id range min CIFS id range max Value DOMAIN <as needed> Checked DOMAIN.COM IP or FQDN (default) ldap Page 4 of 6
5 Gateway LDAP Settings The following LDAP settings are examples of an LDAP schema for AD/LDAP integration with the SwiftStack Gateway. Of course, the examples below might need to be adjusted for your LDAP environment. If uncertain, please consult your organization s LDAP administrator. LDAP Setting LDAP enabled LDAP server list Value Checked <FQDN or IP of LDAP servers> LDAP server port 389 LDAP version LDAP base DN LDAP bind DN LDAP bind password LDAP scope 3 (default) <your LDAP base DN> <your LDAP bind DN> <your LDAP bind password> subtree (default) LDAP timeout 5 LDAP bind timeout 5 LDAP referrals LDAP group lookups Checked (default) Unchecked (default) Page 5 of 6
6 Troubleshooting wbinfo shows AD users/groups, but getent doesn t While winbind is capable of talking to Active Directory to get AD user and group information, the actual gateway relies on its internal Name Services to look up users and groups. Information from winbind is fed into the Name Services via a special winbind libnss. On Ubuntu, this library is provided in a separate package called libnss-winbind. If this package is not installed, username/group resolution will not work. To remedy, manually install this package with the command: $ sudo apt-get install libnss-winbind On CentOS/RHEL, this library is included with the winbind packages, and does not need to be installed separately. Page 6 of 6
Configuring Sponsor Authentication
CHAPTER 4 Sponsors are the people who use Cisco NAC Guest Server to create guest accounts. Sponsor authentication authenticates sponsor users to the Sponsor interface of the Guest Server. There are five
Summary. How-To: Active Directory Integration. April, 2006
How-To How-To Integrate CanIt-PRO with Active Directory: April, 2006 Summary Several organizations use Active Directory to manage their user accounts. This paper describes how to integrate CanIt-PRO with
Upgrading User-ID. Tech Note PAN-OS 4.1. 2011, Palo Alto Networks, Inc.
Upgrading User-ID Tech Note PAN-OS 4.1 Revision B 2011, Palo Alto Networks, Inc. Overview PAN-OS 4.1 introduces significant improvements in the User-ID feature by adding support for multiple user directories,
SUSE Manager 1.2.x ADS Authentication
Best Practice www.suse.com SUSE Manager 1.2.x ADS Authentication How to use MS-ADS authentiction (Version 0.7 / March 2 nd 2012) P r e f a c e This paper should help to integrate SUSE Manager to an existing
Intel Entry Storage System SS4200-E Active Directory Implementation and Troubleshooting
Intel Entry Storage System SS4200-E Active Directory Implementation and Troubleshooting 1 Active Directory Overview SS4200-E Active Directory is based on the Samba 3 implementation The SS4200-E will function
How to Join QNAP NAS to Microsoft Active Directory (AD)
How to Join QNAP NAS to Microsoft Active Directory (AD) What is Active Directory? Active Directory is a Microsoft directory used in Windows environments to centrally store, share, and manage the information
To enable an application to use external usernames and passwords, you need to first configure CA EEM to use external directories.
Most clients utilize an external directory tool, such as Microsoft Active Directory, to provide authentication. CA Embedded Entitlements Manager (EEM) can be configured to integrate with the same external
Dell Compellent Storage Center
Dell Compellent Storage Center Active Directory Integration Best Practices Guide Dell Compellent Technical Solutions Group January, 2013 THIS BEST PRACTICES GUIDE IS FOR INFORMATIONAL PURPOSES ONLY, AND
CYAN SECURE WEB HOWTO. NTLM Authentication
CYAN SECURE WEB HOWTO June 2008 Applies to: CYAN Secure Web 1.4 and above NTLM helps to transparently synchronize user names and passwords of an Active Directory Domain and use them for authentication.
Configuring User Identification via Active Directory
Configuring User Identification via Active Directory Version 1.0 PAN-OS 5.0.1 Johan Loos johan@accessdenied.be User Identification Overview User Identification allows you to create security policies based
Basic Configuration. Key Operator Tools older products. Program/Change LDAP Server (page 3 of keyop tools) Use LDAP Server must be ON to work
Where to configure: User Tools Basic Configuration Key Operator Tools older products Program/Change LDAP Server (page 3 of keyop tools) Use LDAP Server must be ON to work Administrator Tools newest products
LDaemon. This document is provided as a step by step procedure for setting up LDaemon and common LDaemon clients.
LDaemon This document is provided as a step by step procedure for setting up LDaemon and common LDaemon clients. LDaemon... 1 What you should know before installing LDaemon:... 2 ACTIVE DIRECTORY... 2
Alcatel-Lucent Extended Communication Server Active directory synchronization : installation and administration
Alcatel-Lucent Extended Communication Server Active directory synchronization : installation and administration September, 2009 TC1312 Alcatel-Lucent Office Offer - All Rights Reserved Alcatel-Lucent 2009
Managing User Accounts
Managing User Accounts This chapter includes the following sections: Configuring Local Users, page 1 Active Directory, page 2 Viewing User Sessions, page 6 Configuring Local Users Before You Begin You
Collax Active Directory
Collax Active Directory Howto This howto describes the configuration of a Collax server for joining a Windows Active Directory Service (ADS) domain. Furthermore, this howto focuses on how to set up the
Configuring MailArchiva with Insight Server
Copyright 2009 Bynari Inc., All rights reserved. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopy, recording, or any
Integrating Linux systems with Active Directory
Integrating Linux systems with Active Directory Dmitri Pal Engineering Director, Red Hat, Inc. Security Camp at BU Agenda Problem statement Aspects of integration Integration options Recommendations Security
Enterprise Apple Xserve Wiki and Blog using Active Directory. Table Of Contents. Prerequisites 1. Introduction 1
Table Of Contents Prerequisites 1 Introduction 1 Making the Xserve an Open Directory Master 2 Binding the Xserve to Active Directory 3 Creating a Certificate 3 Setting up Apache Web Server 4 Applying the
Instructions for Adding a MacOS 10.4.x Server to ASURITE for File Sharing. Installation Section
Instructions for Adding a MacOS 10.4.x Server to ASURITE for File Sharing Installation Section Purpose: We are setting up a server in ASU s specific environment. Power on the Server Insert the CD Hold
The following process allows you to configure exacqvision permissions and privileges for accounts that exist on an Active Directory server:
Ubuntu Linux Server & Client and Active Directory 1 Configuration The following process allows you to configure exacqvision permissions and privileges for accounts that exist on an Active Directory server:
HP Device Manager 4.7
Technical white paper HP Device Manager 4.7 LDAP Troubleshooting Guide Table of contents Introduction... 2 HPDM LDAP-related context and background... 2 LDAP in HPDM... 2 Full domain account name login...
Chapter Thirteen (b): Using Active Directory Integration
Chapter Thirteen (b): Using Active Directory Integration Summary of Chapter: How to add a User to your Net/Cache/SecurePilot that will match your Active Directory Security Group. How to set-up your Net/Cache/SecurePilot
Configuring HAproxy as a SwiftStack Load Balancer
Configuring HAproxy as a SwiftStack Load Balancer To illustrate how a SwiftStack cluster can be configured with an external load balancer, such as HAProxy, let s walk through a step-by-step example of
Using LifeSize systems with Microsoft Office Communications Server 2007. Server Setup
Using LifeSize systems with Microsoft Office Communications Server 2007 This technical note describes the steps to integrate a LifeSize video communications device with Microsoft Office Communication Server
1 Introduction. Ubuntu Linux Server & Client and Active Directory. www.exacq.com Page 1 of 14
Ubuntu Linux Server & Client and Active Directory 1 Introduction For an organization using Active Directory (AD) for user management of information technology services, integrating exacqvision into the
Instructions for Adding a MacOS 10.4.x Client to ASURITE
Instructions for Adding a MacOS 10.4.x Client to ASURITE Before beginning, it would be prudent not to have an account with the same username and password as your Active Directory account. For DHCP Workstations:
LDAP User Guide PowerSchool Premier 5.1 Student Information System
PowerSchool Premier 5.1 Student Information System Document Properties Copyright Owner Copyright 2007 Pearson Education, Inc. or its affiliates. All rights reserved. This document is the property of Pearson
Managing User Accounts
Managing User Accounts This chapter includes the following sections: Active Directory, page 1 Configuring Local Users, page 3 Viewing User Sessions, page 5 Active Directory Active Directory is a technology
NETASQ ACTIVE DIRECTORY INTEGRATION
NETASQ ACTIVE DIRECTORY INTEGRATION NETASQ ACTIVE DIRECTORY INTEGRATION RUNNING THE DIRECTORY CONFIGURATION WIZARD 2 VALIDATING LDAP CONNECTION 5 AUTHENTICATION SETTINGS 6 User authentication 6 Kerberos
Installation Steps for PAN User-ID Agent
Installation Steps for PAN User-ID Agent If you have an Active Directory domain, and would like the Palo Alto Networks firewall to match traffic to particular logged-in users, you can install the PAN User-ID
Configuring an IP (SIP) Polycom Soundstation on the Avaya IP Office
Hardware used for this documentation Polycom Soundstation IP 6000 Avaya IP500V2 firmware 7.0.23 Set the Polycom with an IP Address Step 1: Initial setup If your Soundstation does not automatically register
OnCommand Performance Manager 1.1
OnCommand Performance Manager 1.1 Installation and Setup Guide For Red Hat Enterprise Linux NetApp, Inc. 495 East Java Drive Sunnyvale, CA 94089 U.S. Telephone: +1 (408) 822-6000 Fax: +1 (408) 822-4501
(june 2007 -> this is version 3.025a)
U s i n g t h e L i n u x P C o n t h e M e e t P C V L A N This article was published on www.tudelft.nl/itt Date: june, 2007 Author: Boris van Es Version: 1.0 Case In your lab there are several computers
How To Enable A Websphere To Communicate With Ssl On An Ipad From Aaya One X Portal 1.1.3 On A Pc Or Macbook Or Ipad (For Acedo) On A Network With A Password Protected (
Avaya one X Portal 1.1.3 Lightweight Directory Access Protocol (LDAP) over Secure Socket Layer (SSL) Configuration This document provides configuration steps for Avaya one X Portal s 1.1.3 communication
Customer Tips. Configuring Color Access on the WorkCentre 7328/7335/7345 using Windows Active Directory. for the user. Overview
Xerox Multifunction Devices Customer Tips February 13, 2008 This document applies to the stated Xerox products. It is assumed that your device is equipped with the appropriate option(s) to support the
Integrating Mac OS X 10.6 with Active Directory. 1 April 2010
Integrating Mac OS X 10.6 with Active Directory 1 April 2010 Introduction Apple Macintosh Computers running Mac OS X 10.6 can be integrated with the Boston University Active Directory to allow use of Active
CA Performance Center
CA Performance Center Single Sign-On User Guide 2.4 This Documentation, which includes embedded help systems and electronically distributed materials, (hereinafter referred to as the Documentation ) is
Integration with Active Directory. Jeremy Allison Samba Team
Integration with Active Directory Jeremy Allison Samba Team Benefits of using Active Directory Unlike the earlier Microsoft Windows NT 4.x Domain directory service which used proprietary DCE/RPC calls,
Information Systems Services. Configuring Entourage 2008 to connect to the University s Exchange service Version 2.2 February 2009
Information Systems Services Configuring Entourage 2008 to connect to the University s Exchange service Configuring Entourage 2008 to connect to the University s Exchange service Contents Contents... 2
LDAP Implementation AP561x KVM Switches. All content in this presentation is protected 2008 American Power Conversion Corporation
LDAP Implementation AP561x KVM Switches All content in this presentation is protected 2008 American Power Conversion Corporation LDAP Implementation Does not require LDAP Schema to be touched! Uses existing
Technical Publications
January 09 babytel ITSP Setup Author: Zultys Technical Support This document covers how to set up a babytel account. For ITSP Accounts ALG is required. For further information on ALG please refer to the
Hansoft LDAP Integration
Hansoft LDAP Integration The Hansoft LDAP Integration synchronizes Hansoft resources to user accounts in an LDAP directory server, such as Windows Active Directory. It matches accounts on login names and
Active Directory Integration
January 11, 2011 Author: Audience: SWAT Team Evaluator Product: Cymphonix Network Composer EX Series, XLi OS version 9 Active Directory Integration The following steps will guide you through the process
Avatier Identity Management Suite
Avatier Identity Management Suite Migrating AIMS Configuration and Audit Log Data To Microsoft SQL Server Version 9 2603 Camino Ramon Suite 110 San Ramon, CA 94583 Phone: 800-609-8610 925-217-5170 FAX:
How To Connect A Gemalto To A Germanto Server To A Joniper Ssl Vpn On A Pb.Net 2.Net 3.5.1 (Net 2) On A Gmaalto.Com Web Server
Application Note: Integrate Juniper SSL VPN with Gemalto SA Server SASolutions@gemalto.com October 2007 www.gemalto.com Table of contents Table of contents... 2 Overview... 3 Architecture... 5 Configure
CONFIGURING ACTIVE DIRECTORY IN LIFELINE
White Paper CONFIGURING ACTIVE DIRECTORY IN LIFELINE CONTENTS Introduction 1 Audience 1 Terminology 1 Test Environment 2 Joining a Lenovo network storage device to an AD domain 3 Importing Domain Users
Integrating LANGuardian with Active Directory
Integrating LANGuardian with Active Directory 01 February 2012 This document describes how to integrate LANGuardian with Microsoft Windows Server and Active Directory. Overview With the optional Identity
Workspot Configuration Guide for the Cisco Adaptive Security Appliance
Workspot Configuration Guide for the Cisco Adaptive Security Appliance Workspot, Inc. 1/27/2015 Cisco ASA and Workspot Overview The Cisco Adaptive Security Appliance (ASA) provides organizations with secure,
Integrating Red Hat Enterprise Linux 6 with Microsoft Active Directory Presentation
Integrating Red Hat Enterprise Linux 6 with Microsoft Active Directory Presentation Agenda Overview Components Considerations Configurations Futures Summary What is needed? Thorough understanding components,
Charles Firth charles@firthconsulting.com. Managing Macs in a Windows World
Charles Firth charles@firthconsulting.com Managing Macs in a Windows World Prerequisites Familiarity with Windows Active Directory networks Interest in Macintosh OSX integration and support Basic understanding
Only LDAP-synchronized users can access SAML SSO-enabled web applications. Local end users and applications users cannot access them.
This chapter provides information about the Security Assertion Markup Language (SAML) Single Sign-On feature, which allows administrative users to access certain Cisco Unified Communications Manager and
How to Logon with Domain Credentials to a Server in a Workgroup
How to Logon with Domain Credentials to a Server in a Workgroup Johan Loos johan@accessdenied.be Version 1.0 Authentication Overview Basically when you logon to a Windows Server you can logon locally using
Simple Scan to Email Setup Guide
Simple Scan to Email Setup Guide Document Centre 555/545/535 Dc04cc0336 Scan to Email Scanning to email from a Xerox DC 555/545/535 requires the support of external email services on a network. These services
SCADA Security. Enabling Integrated Windows Authentication For CitectSCADA Web Client. Applies To: CitectSCADA 6.xx and 7.xx VijeoCitect 6.xx and 7.
Enabling Integrated Windows Authentication For CitectSCADA Web Client Applies To: CitectSCADA 6.xx and 7.xx VijeoCitect 6.xx and 7.xx Summary: What is the difference between Basic Authentication and Windows
Contents. Introduction. Prerequisites. Requirements. Components Used
Contents Introduction Prerequisites Requirements Components Used Background Information Configure Step 1. Configure the Firepower User Agent for Single-Sign-On Step 2. Integrate the Firepower Management
Enabling single sign-on for Cognos 8/10 with Active Directory
Enabling single sign-on for Cognos 8/10 with Active Directory Overview QueryVision Note: Overview This document pulls together information from a number of QueryVision and IBM/Cognos material that are
HP Device Manager 4.6
Technical white paper HP Device Manager 4.6 LDAP Troubleshooting Guide Table of contents Introduction... 2 HPDM LDAP-related context and background... 2 LDAP in HPDM... 2 Configuring User Authentication...
How To - Implement Clientless Single Sign On Authentication in Single Active Directory Domain Controller Environment
How To - Implement Clientless Single Sign On Authentication in Single Active Directory Domain Controller Environment How To - Implement Clientless Single Sign On Authentication with Active Directory Applicable
Stonesoft Firewall/VPN 5.4 Windows Server 2008 R2
Stonesoft Firewall/VPN 5.4 Windows Server 2008 R2 End-User Authentication Using Active Directory and Network Policy Server C ONTENTS Introduction to NPS Authentication with AD... 2 Registering the NPS
IIS, FTP Server and Windows
IIS, FTP Server and Windows The Objective: To setup, configure and test FTP server. Requirement: Any version of the Windows 2000 Server. FTP Windows s component. Internet Information Services, IIS. Steps:
SchoolBooking SSO Integration Guide
SchoolBooking SSO Integration Guide Before you start This guide has been written to help you configure SchoolBooking to operate with SSO (Single Sign on) Please treat this document as a reference guide,
Configuring Squid Proxy, Active Directory Authentication and SurfProtect ICAP Access
Configuring Squid Proxy, Active Directory Authentication and SurfProtect ICAP Access Contents Introduction 3 To Configure 4 Squid Server... 4 Windows Domain Controller... 4 Configuration 4 DNS... 4 NTP...
Network Startup Resource Center www.nsrc.org
λ Wireless Lab λ 802.1x Authentication Network Startup Resource Center www.nsrc.org Last edit: Patrick Okui, Nov 2015 These materials are licensed under the Creative Commons Attribution-NonCommercial 4.0
How to Configure Active Directory based User Authentication
How to Configure Active Directory based User Authentication You Must Have: Microsoft server with Active Directory configured. Windows 2000 Server is configured as Active Directory server in this example.
Active Directory Service. Integration Parameters and Implementation
Active Directory Service Integration s and Implementation Revised January, 2014 Table of Contents Overview... 3 Getting Started... 3 Migrating Your Users... 7 Manually Adding or Editing Users with the
Enter host information:
Active Directory DataSource Configuration for Avaya OSPC OSPC LDAP Integration overview LDAP based data sources like Microsoft s Active Directory (AD) will be a popular integration for the OSPC phonebook
Desktop : Ubuntu 10.04 Desktop, Ubuntu 12.04 Desktop Server : RedHat EL 5, RedHat EL 6, Ubuntu 10.04 Server, Ubuntu 12.04 Server, CentOS 5, CentOS 6
201 Datavoice House, PO Box 267, Stellenbosch, 7599 16 Elektron Avenue, Technopark, Tel: +27 218886500 Stellenbosch, 7600 Fax: +27 218886502 Adept Internet (Pty) Ltd. Reg. no: 1984/01310/07 VAT No: 4620143786
DESLock+ Basic Setup Guide Version 1.20, rev: June 9th 2014
DESLock+ Basic Setup Guide Version 1.20, rev: June 9th 2014 Contents Overview... 2 System requirements:... 2 Before installing... 3 Download and installation... 3 Configure DESLock+ Enterprise Server...
File sharing in Windows XP
File sharing in Windows XP Advantages File sharing involves making the content of one or more directories available through the network. All Windows systems have standard devices making it easy to share
F-Secure Messaging Security Gateway. Deployment Guide
F-Secure Messaging Security Gateway Deployment Guide TOC F-Secure Messaging Security Gateway Contents Chapter 1: Deploying F-Secure Messaging Security Gateway...3 1.1 The typical product deployment model...4
VMware Identity Manager Administration
VMware Identity Manager Administration VMware Identity Manager 2.6 This document supports the version of each product listed and supports all subsequent versions until the document is replaced by a new
Big Data Operations Guide for Cloudera Manager v5.x Hadoop
Big Data Operations Guide for Cloudera Manager v5.x Hadoop Logging into the Enterprise Cloudera Manager 1. On the server where you have installed 'Cloudera Manager', make sure that the server is running,
Basic Exchange Setup Guide
Basic Exchange Setup Guide The following document and screenshots are provided for a single Microsoft Exchange Small Business Server 2003 or Exchange Server 2007 setup. These instructions are not provided
VMware Identity Manager Connector Installation and Configuration
VMware Identity Manager Connector Installation and Configuration VMware Identity Manager This document supports the version of each product listed and supports all subsequent versions until the document
SCOPTEL WITH ACTIVE DIRECTORY USER DOCUMENTATION
SCOPTEL WITH ACTIVE DIRECTORY USER DOCUMENTATION Table of content ScopTel with Active Directory... 3 Software Features... 3 Software Compatibility... 3 Requirements... 3 ScopTel Configuration... 4 Prerequisites...
Creating Home Directories for Windows and Macintosh Computers
ExtremeZ-IP Active Directory Integrated Home Directories Configuration! 1 Active Directory Integrated Home Directories Overview This document explains how to configure home directories in Active Directory
Advanced Administration
BlackBerry Enterprise Service 10 BlackBerry Device Service Version: 10.2 Advanced Administration Guide Published: 2014-09-10 SWD-20140909133530796 Contents 1 Introduction...11 About this guide...12 What
Integrating Webalo with LDAP or Active Directory
Integrating Webalo with LDAP or Active Directory Webalo can be integrated with an external directory to identify valid Webalo users and then authenticate them to the Webalo appliance. Integration with
Getting Started with Clearlogin A Guide for Administrators V1.01
Getting Started with Clearlogin A Guide for Administrators V1.01 Clearlogin makes secure access to the cloud easy for users, administrators, and developers. The following guide explains the functionality
LucidNAS Quick Start Guide
LucidNAS Quick Start Guide This section demonstrates the initial preparation that should be performed before you start using the LucidNAS system. Set Administrative Access By default, no password is required
How To Configure A Bomgar.Com To Authenticate To A Rdius Server For Multi Factor Authentication
Security Provider Integration RADIUS Server 2015 Bomgar Corporation. All rights reserved worldwide. BOMGAR and the BOMGAR logo are trademarks of Bomgar Corporation; other trademarks shown are the property
Microsoft Entourage 2008 / Microsoft Exchange Server 2010. Installation and Configuration Instructions
Microsoft Entourage 2008 / Microsoft Exchange Server 2010 Installation and Configuration Instructions Table of Contents How to connect Microsoft Entourage 2008 EWS to the Exchange Server... 3 Important
Vocia MS-1 Voice-over-IP Interface. Avaya System Verification. Configuring Avaya Aura Session Manager system with Biamp s Vocia MS-1
Configuring Avaya Aura Session Manager system with Biamp s Vocia MS-1 Vocia MS-1 Voice-over-IP Interface The Biamp Vocia Message Server (MS-1) includes functionality to allow pages to be initiated over
IPBrick - Member of AD domain IPBrick iportalmais
IPBrick - Member of AD domain IPBrick iportalmais March 2009 2 Copyright c iportalmais All rights reserved. March 2009. The information in this document can be changed without further notice. The declarations,
The SSL device also supports the 64-bit Internet Explorer with new ActiveX loaders for Assessment, Abolishment, and the Access Client.
WatchGuard SSL v3.2 Release Notes Supported Devices SSL 100 and 560 WatchGuard SSL OS Build 355419 Revision Date January 28, 2013 Introduction WatchGuard is pleased to announce the release of WatchGuard
PineApp Surf-SeCure Quick
PineApp Surf-SeCure Quick Installation Guide September 2010 WEB BASED INSTALLATION SURF-SECURE AS PROXY 1. Once logged in, set the appliance s clock: a. Click on the Edit link under Time-Zone section.
800-782-3762 www.stbernard.com. Active Directory 2008 Implementation. Version 6.410
800-782-3762 www.stbernard.com Active Directory 2008 Implementation Version 6.410 Contents 1 INTRODUCTION...2 1.1 Scope... 2 1.2 Definition of Terms... 2 2 SERVER CONFIGURATION...3 2.1 Supported Deployment
Using LifeSize Systems with Microsoft Office Communications Server 2007
Using LifeSize Systems with Microsoft Office Communications Server 2007 This technical note describes the steps to integrate a LifeSize video communications device with Microsoft Office Communication Server
Security Provider Integration Kerberos Authentication
Security Provider Integration Kerberos Authentication 2015 Bomgar Corporation. All rights reserved worldwide. BOMGAR and the BOMGAR logo are trademarks of Bomgar Corporation; other trademarks shown are
MICROSOFT ISA SERVER 2006
OTP SERVER INTEGRATION MODULE MICROSOFT ISA SERVER 2006 Copyright, NordicEdge, 2010 www.nordicedge.se Copyright, 2010, NordicEdge AB Page 1 of 10 1 Introduction 1.1 OTP Server Overview Nordic Edge OTP
User Management Guide
AlienVault Unified Security Management (USM) 4.x-5.x User Management Guide USM v4.x-5.x User Management Guide, rev 1 Copyright 2015 AlienVault, Inc. All rights reserved. The AlienVault Logo, AlienVault,
Scan to E-mail Quick Setup Guide
Xerox WorkCentre M118i Scan to E-mail Quick Setup Guide 701P42574 This guide provides a quick reference for setting up the Scan to E-mail feature on the Xerox WorkCentre M118i. It includes procedures for:
Configuring Color Access on the WorkCentre 7120 Using Microsoft Active Directory Customer Tip
Configuring Color Access on the WorkCentre 7120 Using Microsoft Active Directory Customer Tip October 21, 2010 Overview This document describes how to limit access to color copying and printing on the
Field Description Example. IP address of your DNS server. It is used to resolve fully qualified domain names
DataCove DT Active Directory Authentication In Active Directory (AD) authentication mode, the server uses NTLM v2 and LDAP protocols to authenticate users residing in Active Directory. The login procedure
Active Directory integration with CloudByte ElastiStor
Active Directory integration with CloudByte ElastiStor Prerequisite Change the time and the time zone of the Active Directory Server to the VSM time and time zone. Enabling Active Directory at VSM level
Active Directory Authenication
Oracle Business Intelligence 11g Active Directory Authenication Antony Heljula November 2012 Page 1 TABLE OF CONTENTS 1. Authentication With Active Directory... 3 1.1 Overview... 3 1.2 Set WebLogic LDAP
From Release 8.0, IPv6 can also be used to configure the LDAP server on the controller.
Information About LDAP, page 1 (GUI), page 2 (CLI), page 4 Information About LDAP An LDAP backend database allows the controller to query an LDAP server for the credentials (username and password) of a
Basic Exchange Setup Guide
Basic Exchange Setup Guide The following document and screenshots are provided for a single Microsoft Exchange Small Business Server 2003 or Exchange Server 2007 setup. These instructions are not provided
Citrix XenMobile Mobile Device Management
Citrix XenMobile Mobile Device Management Akash Phoenix Chapter No. 4 "XenMobile Device Manager Deployment" In this package, you will find: A Biography of the author of the book A preview chapter from
v7.8.2 Release Notes for Websense Content Gateway
v7.8.2 Release Notes for Websense Content Gateway Topic 60086 Web Security Gateway and Gateway Anywhere 12-Mar-2014 These Release Notes are an introduction to Websense Content Gateway version 7.8.2. New