Bathroom Vanity. Page 1 of 16
|
|
- Lydia Norton
- 7 years ago
- Views:
Transcription
1 Bathroom Vanity Page 1 of 16
2 Introduction This plan makes a bathroom vanity 37 inches wide, 22 inches deep and inches high to be fitted with a Vessel Style sink and faucet. All my builds are made with pocket hole joinery. You will need a pocket hole jig tool such as a Kreg Pocket Hole Jig in order to build them. I have tried to ensure all steps are covered in these plans but if you find any errors in the plans or have a question then please me at info@andrewharriswoodwork.com to let me know. Page 2 of 16
3 Shopping List I used pine. Where it says select these are the Select Pine boards you can get in Home Depot or Lowes. Size Length Quantity Board Number 1 by 2 8 feet 2 1 and 2 1 by 3 8 feet 3 3, 4 and 5 1 by 4 8 feet 2 6 and 7 1 by 4 select 6 feet by 6 6 feet by 6 select 8 feet 4 10,11,12 and 13 ¾ inch plywood 4 feet by 2 feet 1 ¼ inch plywood Legs See build notes as will depend on method of drawer construction I used these ones You will also need: Pocket Hole Tool such as a Kreg Pocket Hole Jig 1.25 inch pocket screws 1.25 inch wood screws 2 inch wood screws ¾ inch finishing nails Wood glue Drawer and Door pulls (the cost includes the ones I used which came to around $20) Hinges (the cost includes the ones I used which came to around $20) Hole Saw to drill hole for faucet pipe Estimated Material Cost: $420 Page 3 of 16
4 Cut list Please read all instructions before cutting wood as shown below. I suggest some pieces are cut as you go to ensure a tight fit. To minimize the number of boards to use plan your cuts I have given details of which board you should cut the piece from. If you find a more economical solution then please let me know. Size Length (inches) Quantity Used For Board Number 1 by Drawer rails 1 1 by Drawer rails 1 1 by Front Top Rail 1 1 by Door Inserts 2 1 by Drawer Rail back supports 2 1 by Drawer Rail front Supports 2 1 by Fake Drawer Cross Support 2 1 by Front bottom rail 3 1 by Front side top rail 3 1 by Front side bottom rail 3 1 by Front middle rail 4 1 by Door Panel Vertical 4 1 by Front Vertical Support 4 1 by Door Panel Horizontal 5 1 by Drawer Side 6 1 by Drawer Front 6 1 by Drawer Back 7 1 by Back Support 7 1 by 4 Select Side Panel 8 1 by 4 Select 7 2 Door Panel Vertical 8 1 by Back rail 9 1 by 6 Select Side Panel 10 1 by 6 Select 37 2 Top 11 1 by 6 Select 26 2 Top 12 1 by 6 Select 22 2 Top 13 1 by 6 Select Drawer Front 12 Page 4 of 16
5 Size Length (inches) Quantity Used For Board Number ¼ inch ply ¾ inch ply See plans for drawer bottoms Base Page 5 of 16
6 Step 1 Make the two Side panel inserts Use the two pieces of 1 by 3 measuring 14.5 inches in length, the two pieces of 1 by 6 measuring 17 ¾ inches in length and one of the 1 by 4 pieces measuring 17 ¾ inches in length to make each side panel. Before joining the pieces together I sanded all edges of each piece slightly rounded so that once joined you could see the join to give a paneled look. Put the pocket holes on the side that will be used as the inside and also put pocket holes in the top and bottom of each piece to fix to the top and bottom rails. I put two pocket holes on the ends of the 1 by 6s and one on the ends of the 1 by 4. Also put pocket holes on the outside edges so that the panel can be fitted to the legs. If you prefer you can use a piece of plywood for a solid panel look instead. Page 6 of 16
7 Step 2 Make the two Side frames Make the side frame by attaching the two 29.5 inch legs and the side panels together. Make sure the outside face of the panel is flush with what will be the outside of the legs. On the inside of each panel I put pocket holes on the top edge facing upwards to use to fix the top on with. Page 7 of 16
8 Step 3 Add the Front rails Add the 1 by 2 piece measuring 30 inch in length as the top front rail and the two 1 by 3 pieces measuring 30 inches in length as the middle and bottom rails. Add the 12 ¼ inch piece of 1 by 3 as the vertical support. Make sure the pocket holes are on the inside. The pocket holes should be drilled on the narrow part of each piece. Page 8 of 16
9 Step 4 Add the back rails Drill pocket holes on te narrow end of each piece to attach them to the legs. I also put pocket holes on the inside of the 1 by 6 piece on the top edge facing upwards to use to fix the top. Note depending on where your pipe work comes out the wall you may need to adjust the width of pieces you use for the back rails. Page 9 of 16
10 Step 5 Make the Top Drawers Drill pocket holes in the both ends of the 7 ¾ inch length drawer pieces. Note my drawer slides required a gap of ½ inch either side of the drawer to fit the slide. Hence the 7 ¾ inch length pieces here. If your drawer slides need a different gap then you will need to adjust accordingly. Join the 18 inch pieces to the 7 ¾ inch lengths to form the drawers. You can either route the sides to fit ¼ inch plywood base inside or fix the base to the bottom. Fit the drawer slides to the drawers as well following the instructions for the ones you have purchased. I used 18 inch soft close drawer slides. They needed a gap of half an inch either side. Therefore the total width of the drawer had to be 9 1/4 inches (1 inch narrower than the 10 ¼ inch opening) Page 10 of 16
11 Step 6 Drawer slide rail vertical supports Add the 7 ¼ inch long and 7 ½ pieces of 1 by 2 as shown below. Page 11 of 16
12 Step 7 Fit the drawer slide rails as shown Fit the two 14 ½ and two 17 ½ long pieces of 1 by 2 as the drawer slide rails as shown. Step 8 Fit the drawer slides Follow the instructions of your slides to fit them to the sides of the cabinet. Usually there should end up being half an inch gap between the bottom of the drawers and top of the rail underneath it but follow the instructions that come with your drawer slides. Step 9 Fit the drawer fronts Fit the drawer fronts ensuring equal gap at top and outer edge for both. Drill two holes through the inner drawer front and then fix the outer drawer front by screwing through the inner drawer front into the outer drawer front using 1 ¼ inch screws. Tip - clamp the drawer front in position when happy with the spacing and then screw it in place. Page 12 of 16
13 Step 10 - Fit the fake middle drawer fronts Add the cross support to screw the fake drawer front to as shown. Fit the drawer fronts ensuring equal gap at top and outer edge for both. Drill two holes through the inner drawer front and then fix the outer drawer front by screwing through the support into the drawer front using 1 ¼ inch screws. Tip - clamp the drawer front in position when happy with the spacing and then screw it in place. Page 13 of 16
14 Step 11 Make the Doors Make each doors using the following pieces for each one: Two pieces of 1 by 3 measuring 12inches long Two pieces or 1 by 3 measuring 8 ½ inches long Two pieces of 1 by 4 measuring 7 inches long One piece of 1 by 2 measuring 7 inches long Page 14 of 16
15 Step 12 - Make the top Make the top from the 1 by 6 pieces as shown below. Tip : if doing mitered corners then don t cut the boards to length first. Cut one of the miters on the piece then measure the piece from the corner of the miter and cut the miter at the other end of the piece. Step 13 Fit the top Drill through the top of the front 2 by 4 rail so the top can be screwed on from underneath. Place the top with the good side down and then place the upturned cabinet on top. Make sure you have equal gap all around and then fix the sides and back with 1 ¼ inch pocket hole screws and the front edge with 2 inch wood screws through the front rail. Page 15 of 16
16 Step 14 - Fit the cabinet bottom Add the cabinet base using the ¾ inch thick piece of plywood measuring 34 by 19 inches. You will need to cut out a 2 ¼ inch square notch in each corner as shown below. Drill pocket holes around all the edges and fit with the pocket holes on the underside. Step 15 Finish Sand well to smooth our joints and remove any wood glue residue. Apply Pre stain and your choice of color or paint as desired. Step 16 Fit the doors and add hardware Once finished fit the doors in place with hardware of your choice. For the drawers you will need to temporarily remove the front drawer parts. Step 17 - Drill Holes for Vessel Sink Depending on the sink and faucet being used drill a hole for the drain pipe and faucet as required using a hole saw. Page 16 of 16
DIY CABINET REFACING INSTALLATION GUIDE
DIY CABINET REFACING INSTALLATION GUIDE CABINET REFACING INSTALLATION Are you ready to reface your outdated cabinets? This guide will show you how to install your new Facelifters Cabinet Refacing Products
More informationWine Rack & Glass Storage Bench Chris Gardner
Wine Rack & Glass Storage Bench Chris Gardner Quantity Length Width Material Part 2 48 16 3/4 birch plywood top, bottom 2 14 16 3/4 birch plywood sides 2 14 13 3/4 birch plywood support dividers 2 3 15
More informationHow to Build a Poker Table
How to Build a Poker Table www.pokertablematerials.com 10-Person Poker Table- 96 x 48 These are step by step instructions for building a poker table. The table will measure 48" x 96" and have a 4" wide
More informationKITCHENS. Tip PAGE 1 FITTING YOUR KITCHEN GUIDE. How to mark out a kitchen. Tools required for installing a kitchen STEP ONE STEP TWO STEP THREE
FITTING YOUR KITCHEN GUIDE How to mark out a kitchen PAGE 1 Before starting on the installation, measure 870mm from the lowest point of the floor and mark a datum line around the room to indicate where
More informationwww.cornholesupplies.com
www.cornholesupplies.com How To Build Regulation Cornhole Boards Home of the Original Cornhole Bags and Boards Supply List: 1-4' X 8' Piece of Plywood (pre sanded) 4-2" X 4" X 8' Studs (2 by 4s make sure
More informationEasy Six Cube Bookshelf. Copyrighted Material. Page 1
Compare to: Land of Nod Cube Collection, 6 Cube Bookshelf Skill Level: Beginner Easy Six Cube Bookshelf I love the storage cubes in kids rooms because they give you an opportunity to have your children
More informationCedar Cottage Doghouse Plans
Overlapping cedar shingles add an element of charm to this medium size doghouse. The walls, floor, and trim are constructed of solid cedar, making it naturally weather resistant and provides excellent
More informationInstalling Window and Door Mouldings
Installing Window and Door Mouldings About Window and Door Mouldings The trim around windows and doors greatly influences the look and style of your interior. They also bridge the gaps and cover spaces
More informationRouter Table Plans. www.bobsplans.com
www.bobsplans.com Router Table Plans Increase the capabilities of your router with this weekend project. Features a sliding fence with EZ-Mount clamps. These clamps are simple to make and grip tightly
More informationWren Kitchens Installation Tips... 3. Carefully check your kitchen delivery... 4. Measuring out and marking up... 5. Fitting the base cabinets...
tra 1 Index Wren Kitchens Installation Tips... 3 Carefully check your kitchen delivery... 4 Measuring out and marking up... 5 Fitting the base cabinets... 6 Fitting the corner cabinets... 7 The 972mm or
More informationHive Top Ventilation Shims
Hive Top Ventilation Shims When preparing your bee hives for the winter, it is very important to provide for ventilation at the top of the hive. Through out the winter, the bees are expelling a lot of
More informationGarage Workbench Plans
www.bobsplans.com Garage Workbench Plans Every home woodworker knows the importance of making efficient use of the available space in his or her shop. This workbench is designed to provide the maximum
More informationGate Leg Drop Leaf Table Plans
Preparing the table top blanks: Cut and glue enough 3/4 stock to make three panels 40 long by 24 wide (they will be cut to final size at a later time). While the glue dries we will work on the legs. Preparing
More informationThe JIG is UP Or A couple hours up front pays in the long run.
Ed Simon Page 1 of 5 The JIG is UP Or A couple hours up front pays in the long run. A large part of the fun of beekeeping is the construction and assembly of the equipment. Since it is a hobby, I decided
More informationDE Frame with C Series Sidelight
TOOLS REQUIRED Tape measure 6' magnetic level 3' magnetic level Screw gun with clutch adjusted #2 phillips tip #3 phillips tip Screwdriver (used to adjust frame on will using oval slots) Pry Bar Powder
More informationHOW TO INSTALL A BEAUTIFUL NEW KITCHEN
HOW TO INSTALL A BEAUTIFUL NEW KITCHEN Easy to follow step-by-step kitchen cabinet installation TOOL AND MATERIAL LIST Hammer Pry bar Screwdriver Phillips Flathead Level Tape measure Pencil Straight edge
More informationToy Box. Project Plan. Kreg Jig. www.kregjig.com
Toy ox www.kregjig.com Kreg ig 32" What you ll What need You ll Need Toy ox TOOLS 25 Circular Saw Drill Kreg ace Clamp or C-Clmap Kreg ight ngle Clamp DWE & SUPPLIES 25 Materials PTS LIST SOPPIN LIST Quantity
More informationStorage Bins U-BILD. Plan No. 797 A MERICA' S FAVORITE WOODWORKING P LANS. Bill of Material. Cutting Schedule
U-ILD A MERICA' S FAVORITE WOODWORKING P LANS Storage ins Plan No. 797 Copyright U-uild, Inc., 2004. All rights reserved. Printed in the U.S.A. A true country classic, this build-it-yourself storage bin
More informationKITCHEN INSTALLATION GUIDE
KITCHEN INSTALLATION GUIDE The step-by-step guide to installing your new kitchen right The materials and tools you ll need This brochure is your guide to preparing and installing your new kitchen. Inside
More informationSUPER SHED. Indoor shelter for your outdoor tools.
SUPER SHED Indoor shelter for your outdoor tools. Not everyone needs a garden shed. But, if you've no more space on your garage wall for that new leaf rake, if you can't find your potting trowel because
More informationStair Parts Installation. Tricks
Stair Parts Installation Tips & Tricks Introduction Your DIY staircase guide Welcome to the Stairpart home installation guide. Your stairway is both a functional and focal point in your home, so keeping
More informationDIRECTIONS FOR ASSEMBLING BASE & WALL CABINETS
DIRECTIONS FOR ASSEMBLING BASE & WALL CABINETS TheRTAStore.com STEP 1: CLEAR A WORK SPACE Place your RTA cabinet panels on a smooth, scratch resistant surface in a large, open area. (Some people like to
More information2.9 WINDOW & DOOR BUCKS
2.9 WINDOW & DOOR BUCKS Bucks provide attachment surfaces for windows and doors while holding back concrete from these openings during concrete placement. Mark the center and edges of openings as you place
More informationMaking Wooden Hinges
Making Wooden Hinges By Alex Reid - www.mokkou.jp Materials and tools used - 3.2mm straight router bit - 1/8 round-over router bit - Flush-cut straight bit (with bearing on bottom) - Finger-joint jig -
More informationThe tablesaw may be your shop s most valuable cutting. Crosscut Sleds. Foolproof. Innovative approach guarantees perfect results
Foolproof Crosscut Sleds Innovative approach guarantees perfect results B Y A L A N T U R N E R The tablesaw may be your shop s most valuable cutting tool, but for precise, repeatable crosscuts it needs
More informationTotal Quantity: IMPORTANT: Plans are to be used with 3 x6 Plexiglass (SKU #298-017).
# Materials: Quantity Each: 4x4x8 3 2x4x8 2 2x8x8 1 4x8x3/4 plywood 1 3 x6 corkboard (can be 18 of the 1 x1 pieces) 1 3 x6 plexiglass 1 8 door casing 3 Primer 1 qt. Total Quantity: TIPS FOR SUCCESSFUL
More informationHere is your set of Detailed Plans from Copyright 2004 All Rights Reserved
Here is your set of Detailed Plans from Copyright 2004 All Rights Reserved Materials for the House Here is the list of materials you will need to construct the basic house then to cover it with roofing
More informationThese instructions will show you how to install an internal door into a non-loadbearing partition wall. The instructions are split into three parts.
No 8 in the series of 'How to' brochures produced by PlaceMakers, New Zealand How to Frame and Hang a Door These instructions will show you how to install an internal door into a non-loadbearing partition
More informationChildren s Furniture Projects
This is an excerpt from the book Children s Furniture Projects by Jeff Miller Copyright 2002 by The Taunton Press www.taunton.com CHILD S ROCKER KIDS ARE ALWAYS IN MOTION. It s not easy to get them even
More informationHow to Build Your Own CornHole Game
How to Build Your Own CornHole Game DIMENSIONS Here is a diagram with the basic measurements for the Cornhole board game. SUPPLIES 1/2 thick sheet of plywood one 4 x4 or two 2 x4 s 8 long 2 4 s (4) 4 1/2
More informationCeiling Mounted Folding Attic Ladders Installation Instructions
Ceiling Mounted Folding Attic Ladders Installation Instructions WARNING Before you start installing your new Louisville Ceiling Mounted Folding Attic Ladder, you must read and understand the following:
More informationRECLINE IN THE SUMMERTIME Get comfortable on the patio or deck with this sturdy reclining lounge chair
RECLINE IN THE SUMMERTIME Get comfortable on the patio or deck with this sturdy reclining lounge chair As early as the eighth century B.C., the Greeks used a piece of furniture called the kline, for lounging
More informationAssembly Instructions Basic Folding-Leg Box Frame Style
Assembly Instructions Basic Folding-Leg Box Frame Style Basic Folding Leg Cornhole Board Concept 1 2 12 3 1 2 3 15 16 4 1 4 52 9 R1 3 4 6 21 48 12 1 4 Bolt Washer 9 13 16 35 Washer Double Nut CornholePlayers.net
More informationA Simple Approach to Raised-Panel
A Simple Approach to Raised-Panel 82 FINE HOMEBUILDING Wainscot BY GARY STRIEGLER Stock molding and MDF panels transform a room 1 2 3 4 3 5 6 Raised-panel wainscot speaks of a time when craftsmen had an
More informationCustom Cabinets. A Faster, Easier Approach to. Create desks, bookcases, pantries, and more with a slick hybrid design
Create desks, bookcases, pantries, and more with a slick hybrid design and problemsolving pocketscrew joinery BY MIKE MAINES A Faster, Easier Approach to Custom Cabinets When designed and constructed properly,
More informationCabinetry Installation
Cabinetry Installation INTALLATION EQUIPMENT #8 x 2 1 2 screws #8 x 2 1 2 washer head screws Variable speed drill, electric or cordless Extension cord Countersink drill bit Drill bits, 3/16 and 1/4 Assorted
More informationChapter 3 Installing Over-the-Post Railing on an L-Shaped Stair
49 Chapter 3 Installing Over-the-Post Railing on an L-Shaped Stair In this chapter: The Over-the-Post Balustrade System Determining the Rail Centerline Using Rail Bolts Making a Pitch Block Laying Out
More informationPicnic Table Plans. Made out of a single sheet of plywood, it s also portable! By Kevin Ayer. This children's picnic table would
Picnic Table Plans Made out of a single sheet of plywood, it s also portable! By Kevin Ayer Materials One 4- by 8-foot sheet of 3 4-inch AC plywood Twelve 11 4-inch wood screws Primer and exterior paint
More informationArchitectural Casework 06400-01. 1.01 Description of Work
06400-01 1.01 Description of Work A. Extent of each type of architectural millwork and casework as indicated on drawings. Types of architectural casework shall include both stained and plastic laminated
More informationSHELVES. www.tedswoodworking.com
SHELVES It's rare that bookshelves look as interesting as the objects you display on them. After all, how much can you decorate the edges of your shelves and sides? This unit is unusual because the shelves
More information1 Door Tall Unit ASSEMBLY GUIDE. Page 1 of 9. WARNING: Contains small parts, keep out of reach of children.
Page 1 of 9 ASSEMBLY GUIDE 1 Door Tall Unit IMPORTANT Before Commencing Assembly: Read all instructions COMPLETELY Ensure all listed parts are present If any parts are missing from Parts List 1, please
More informationAMERICAN GOTHIC PLAYHOUSE
AMERICAN GOTHIC PLAYHOUSE Project Plan #856 Sheet 1 of 5 Pick a spot and get started with the beautiful that your kids will love. The design of the playhouse includes 35 square feet of interior space plus
More informationTopSky DLG Installation Manual
TopSky DLG Installation Manual Attention: Because after the compound materials solidify, there will be ammonia iris on the surface, which affect the bonding strength afterwards. Please polish with sandpaper
More informationInstallation Instructions
Installation Instructions READ BEFORE INSTALLING UNIT For Low Profile Window Air Conditioner INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Follow each step
More informationINSTALLATION INSTRUCTIONS for Bifold Doors (JII103)
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for premium composite, hollow and solid core molded Bifold Doors. Bifolds are designed for fast
More informationMagnetic Levitation Track Construction Instruction Manual August 2012
This document is intended to be used by Science Olympiad teams to assist them in building a magnetically-levitated track that will meet all specifications in the event rules for Magnetic Levitation and
More informationCOMPLIMENTARY WOODWORKING PLAN
COMPLIMENTARY WOODWORKING PLAN Adirondack Chair This downloadable plan is copyrighted. Please do not share or redistribute this plan in any way. It has been created for Wilton Tools, a division of WMH
More informationInstallation Instructions
READ BEFORE INSTALLING UNIT For Through-the-Wall Air Conditioners To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may be exposed:
More informationPremier & Deluxe 3-Season Room Sliding Glass Door
DTSSGD-11 Premier & Deluxe 3-Season Room Sliding Glass Door Installation Instructions Screen Door Seal Left Side Track Top Track Assembly Right Side Track Right Side Trim Sliding Glass Door Sliding Screen
More informationBuild a Precision. Crosscutting Sled
Build a Precision Crosscutting Sled On-the-money, splinter-free crosscuts are well within your grasp using most well-made tablesaws, but you do have to do a few things to ensure great results cut after
More informationThe Hive Bodies. In the Beekeeper s Work Shop. Building a Bee Hive: The Hive Bodies. by Stephen E. Tilmann
The Hive Bodies In the Beekeeper s Work Shop The hive body is the heart of a managed bee hive colony (Figure 1). It is where the queen lays her eggs, the house bees raise the brood and the workers store
More informationBUILD A TABLETOP LOOM
BUILD A TABLETOP LOOM From 1" x 2" stock (actual 3/4" x 1"1/2) cut: 4 pieces 15" long 4 pieces 5"1/2 long Use the above to make 2 frames for the front and back of the loom. From 1" x 4" stock (actual 3/4"
More informationDEC076 A London 61" Double Sink Vanity Se t
DEC076 A London 61" Double Sink Vanity Se t The Stanton London Collection Collection The 61 London Double Vanity is elegantly constructed of solid oak wood. The white Carrara Marble counter tops classic
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised November 27, 2013 the Easton - R 12'x 20' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.
More informationLadder Shelf Plans Final dimensions: 25 L x 21 W x 72 H
Ladder Shelf Plans Final dimensions: 25 L x 21 W x 72 H Copyright 2011. MLCS Woodworking. Page 1 Router bits and supplies needed: 3/8 Rabbeting bit (#10691) 1 Bottom Cleaning bit (#7941) Top and Bottom
More informationDESK CABINETS & BOOKSHELVES
142 : Desk Base Desk Base Cabinets File Drawer Base Cabinet Desk Base Cabinet 1 Factory Installed Wastebasket FDB1821 DWBT1821 Desk Base cabinets are 12 to 24 wide, 28 1 2 high and 20 3 4 or 24 deep. Cathedral
More informationBase Cabinet with Self-storing Folding Doors and Floor
Usable Kitchens When designing a kitchen for use by persons with mobility impairments, especially those who use wheelchairs, careful layout of the kitchen is crucial to maintaining accessibility. People
More informationQWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS
QWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine TM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical
More informationComposite Stone Veneer
Composite Stone Veneer Installation Guide Ver 1 Jun 2015 www.compstone.com Composite Stone Veneer Installation Guide Contents Introduction & Overview 3 Required Tools 4 Optional Tools 4 Attachment Guidelines:
More informationTrundle Bed Plans (For Use Under Twin or Full-Size Standard Length Beds)
Bunk Beds Unlimited Trundle Bed Plans (For Use Under Twin or Full-Size Standard Length Beds) On the following pages we have included all of the necessary drawings and requirements for a Modified twin-size
More informationImportant Information for Installer & Homeowner
Important Information for Installer & Homeowner Homeowner: Please keep this information for your records, do not discard! Installation Instructions for Wood Frame Construction Replacement (See other side
More informationHow to Build a Strawberry Pyramid Watch the how-to video here.
How to Build a Strawberry Pyramid Watch the how-to video here. This simple, elegant strawberry pyramid can be built by a single person in just one afternoon. Cut the lumber yourself if you have some woodworking
More informationIMPORTANT INSTALLATION GUIDE VALENCIA SQUARE CORNER SHOWER READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING THE INSTALLATION
INSTALLATION GUIDE VALENCIA SQUARE CORNER SHOWER SEALANT REQUIRED TO COMPLETE THIS INSTALLATION: (Not supplied) Sika Sikasil NG (Arctic White) To seal the WHITE shower door and returns to the shower tray.
More informationSpeed-Mat Rectangle Cutter
Speed-Mat Rectangle Cutter 1 Honeycomb baseboard. 2 Left hold down. 14 3 Bottom hold down. 4 4 Left / right rule. 8 5 8 5 Left / right rule pointer. 1 6 Top / bottom rule. 7 Top / bottom rule pointer.
More informationCongratulations on your new IKEA Kitchen, and on the money you saved!
Congratulations on your new IKEA Kitchen, and on the money you saved! INSTALLATION GUIDE FOR YOUR AKURUM KITCHEN Seven steps to a brand new kitchen It s time to discover another major advantage of investing
More informationFF+E Package 1: Casegoods Specifications UCSD NORTH CAMPUS HOUSING, PHASE 1
FF+E Package 1: Casegoods Specifications UCSD NORTH CAMPUS HOUSING, PHASE 1 Issue Date: 3/3/2009 Each furniture item scheduled in this specification manual is assigned a "key" code; each key code is crossreferenced
More informationWindow Installation Instructions
Caution The correct installation methods of windows in full frame or insert applications is critical towards achieving the tested performance of the window and longterm enjoyment and energy savings for
More information1958-64 WINDOW CHANNEL, WEATHERSTRIP & WHISKER STRIP REPLACEMENT FOR 2-DOOR SEDANS
By Denny Williams Photos by Denny Williams 1958-64 WINDOW CHANNEL, WEATHERSTRIP & WHISKER STRIP REPLACEMENT FOR 2-DOOR SEDANS Denny Williams - Technical Writer Denny is first and foremost a dyed-in-thewool
More informationVinyl Brick Mould Field Installation Instructions All Vinyl and Vinyl Clad Windows
Vinyl Brick Mould Field Installation Instructions All Vinyl and Vinyl Clad Windows Viewed from the exterior. IMPORTANT: Please read before you begin installation. TABLE OF CONTENTS AND TOOL / MATERIAL
More informationSAMPLE INSTRUCTIONS. Best Barns USA Assembly Book. the Denver. 12'x 12' or 12'x16' Revised November 29, 2010
Best Barns USA Assembly Book Revised November 29, 2010 SAMPLE INSTRUCTIONS the Denver 12'x 12' or 12'x16' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775
More informationINSTALLATION INSTRUCTIONS for Premium Pocket Windows (JII022) IMPoRtaNt INFoRMatIoN & glossary. safety & HaNdlINg
Thank you for selecting JeLd-weN products. Attached are JeLd-weN s recommended installation instructions for pocket (replacement) double-hung, casement, awning, picture or transom windows, designed to
More informationHfHMD uses LP SmartSide siding and trim.
HfHMD uses LP SmartSide siding and trim. These products are: More durable than cement fiber board. Much more volunteer-friendly to install. When installed correctly, have a 5/50- year pro-rated warranty.
More informationCEILING SYSTEMS. Between us, ideas become reality. Installing. Suspended Ceilings. North America Version
CEILING SYSTEMS Between us, ideas become reality Installing Suspended Ceilings North America Version 1 Installing Armstrong Suspended Ceilings An Armstrong suspended mineral fiber ceiling is functional,
More informationInstallation Instructions
READ BEFORE INSTALLING UNIT For Slider Casement Air Conditioners To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may be exposed:
More informationBeautifully Traditional
Arcade 800mm Single Sliding Door Quadrant - nickel Arcade 900mm Single Sliding Door Quadrant - nickel ARC48 ARC49 INSTALLATION INSTRUCTIONS A www.arcadebathrooms.com IMPORTANT - Please read before installation
More informationBathroom Installation Guide
Bathroom Installation Guide Step-by-step installation of your cabinets We do a lot of groundwork to make it as simple as possible for you to assemble and install your new bathroom furniture yourself. We
More informationWe urge you to read and follow the attached installation instructions. Failure to do so may void the warranty of this garden window unit.
Important Information for New Construction Installations Attention Installer! We urge you to read and follow the attached installation instructions. Failure to do so may void the warranty of this garden
More informationInstallation Instructions For Slider Casement Air Conditioners
Installation Instructions For Slider Casement Air Conditioners NOTE: These instructions describe installation in a typical wood framed window with a wood SLIDE-BY sash, or installation in a metal CASEMENT
More informationBuilding Pluto Subwoofers with Large PVC Pipe
Building Pluto Subwoofers with Large PVC Pipe I decided to make the Pluto subwoofers from 10-12 diameter PVC pipe. It seemed to me that these would be a better visual match to the Plutos themselves. The
More informationClad Direct Glaze Window Installation Instructions
Clad Direct Glaze Window Installation Instructions Sill flashing and sealing: 2. An overview of the proper flashing sequence is shown in figure 1. Please read entire installation instructions carefully
More informationComplete Dovetail Jig Instructions
Complete Dovetail Jig Instructions 18 15 1 12 13 8 (22818) 19 17 16 4 3 6 14 5 9 9 11 10 2 PARTS LIST - COMPLETE DOVETAIL JIG Introduction Your new dovetail jig will cut Full Through Dovetails and three
More informationNATURAL RAILING INSTALLATION INSTRUCTIONS
NTURL RILING INSTLLTION INSTRUCTIONS Manufactured by fiberondecking.com 800.573.8841 FI-0217-PKG 5/14 Natural Railing Installation Instructions Natural Top Rail Profile Required Tools and Supplies: Power
More informationREAD THE INSTRUCTIONS SEVERAL TIMES BEFORE STARTING ASSEMBLY
1954-87 CHEV BED INSTRUCTIONS (Revised Nov 2002) Thank you and congratulations on your purchase of the finest Street Rod Pickup Bed on the market today. The following instructions should help you assemble
More informationHOW-TO LAY HARDBOARD OR PLYWOOD FLOOR OVERLAY
HOW-TO HOW-TO LAY HARDBOARD OR PLYWOOD FLOOR OVERLAY Most floor coverings, if laid over uneven wooden floors, will wear unevenly and look unsightly. The answer is to cover the old boards with hardboard
More informationInstallation Instructions
Installation Instructions 1. Position the unit onto bridging packers. These keep the unit away from any water sitting inside the frame. 2. Centralise the unit within the frame and pack the edges with appropriate
More informationInstallation Instructions
Installation Instructions Built-In Dishwasher If you have questions, call 1-800-4-MY-HOME (1-800-469-4663) or visit our website at: www.sears.com BEFORE YOU BEGIN Read these instructions completely and
More informationArchitectural Condition Survey
Architectural Condition Survey Santa Fe Railroad / AMTRAK Depot, Lawrence. Kansas for the City of Lawrence, 2002 Survey: (student) PI: William Carswell, Associate Dean, School of Architecture, University
More informationIntegral Kit Instructions
Integral Kit Instructions For Fisher & Paykel Cabinet widths of 525, 635, 680, 790 mm wide For curved door Models Series B, C, D & G Manual 814980 Updated August 2008 IMPORTANT If your refrigerator has
More informationTOLL FREE: (866) 591-7792. E-Mail: techmail@vigoindustries.com. www.vigoindustries.com VANITY SPECIFICATIONS. VANITY COMPONENTS Model VG09042K1
VANITY SPECIFICATIONS VANITY COMPONENTS Model VG09042K1 MODEL VG09042K1 FEATURES Freestanding cabinet Soft closing sliding cabinet drawer hardware White, single hole ceramic sink Cabinet ships assembled
More informationQuartz Top Installation Instructions See separate installation instructions for installing your new Vanity.
Quartz Top Installation Instructions See separate installation instructions for installing your new Vanity. GOALS: The top will be positioned on the cabinet with finished edge towards the homeowner and
More informationMGB Chrome Bumper Conversion
MGB Chrome Bumper Conversion Installation Instructions For 1974 1/2-1980 MGB This kit requires cutting, welding, and painting. Professional installation recommended. Note: Every MGB body is slightly different
More informationInstallation Guide. Bath and Wall Surrounds SERIES 7104 1021861-2-B
Installation Guide and Wall Surrounds SERIES 7104 1021861-2-B Thank You For Choosing Sterling We appreciate your commitment to Sterling value. Please take a few minutes to review this manual before you
More informationHow To Repair A House
Assessing Structural Damages Please note-this presentation is only intended to be used as a basic educational tool and is by no means all encompassing. Each property should be treated on a case by case
More informationBuild Your Own Kitchen Cabinets
HOME IMPROVEMENT Build Your Own Kitchen Cabinets RAISED PANELS BEVELED GLASS LIGHTED VALANCE / 8 " INSET DRAWERS 40 If you ve dreamed of building a kitchen full of cabinets, stop dreaming and start building.
More informationPOD Visor Instructions
POD Visor Instructions Please read fully before beginning assembly and mounting the Visor Parts List - Visor Left Part (LV), Visor Right Part (RV) Qty 2, Aluminum Crossbars Hardware - Qty 17, 1/4" X 3/4"
More informationWILDING WALLBEDS BUNK BED INSTALLATION INSTRUCTIONS
WILDING WALLBEDS BUNK BED INSTALLATION INSTRUCTIONS Instruction Booklet 18 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN POWERFUL LIFTING COMPONENTS. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE
More informationIMPORTANT INFORMATION
Curved Quadrant Instruction Manual CQ IMPORTANT INFORMATION Toughened glass is completely safe for use in our shower enclosures and bath screens; providing our products are installed according to our guidelines.
More informationHow to secure your property after a disaster
How to secure your property after a disaster The Red Guide to Recovery HOuse secured properly Board-Up of Windows, Doors and Roof Hole. Lot secured with Perimeter Fencing. Fires, floods, tornadoes, hurricanes,
More informationSHUTTER PROGRAM. www.royalwindowsinc.com CORPORATE OFFICE. 606 Fountain Parkway, Grand Prairie TX 75050
SHUTTER PROGRAM www.royalwindowsinc.com CORPORATE OFFICE 606 Fountain Parkway, Grand Prairie TX 75050 Tel 214.412.1189 or 800.872.2693 Fax. 214.412.1188 or 800.422.2693 Email : sales@royalwindowsinc.com
More informationBUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS
BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS PLEASE READ COMPLETE INSTRUCTIONS BEFORE YOU BEGIN LEAVE INSTALLATION INSTRUCTIONS AND USER'S GUIDE WITH OWNER ALL ELECTRIC WIRING AND PLUMBING MUST BE DONE
More information