ScanMaker 9800XL. Installing and Getting Started. Contents

Transcription

1 ScanMaker 9800XL Installing and Getting Started Contents Trademarks Microtek, ScanMaker, and ScanWizard TM Pro are trademarks or registered trademarks of Microtek International, Inc. Macintosh and Apple are registered trademarks of Apple Computer, Inc. Windows is a registered trademark of Microsoft Corporation. All other products or name brands are trademarks of their respective holders. Important Documents you scan may be protected under copyright law. The unauthorized use of such documents could be a violation of the rights of the copyright holder. Microtek bears no responsibility for the unauthorized use of copyrighted materials. Introduction... 2 System Requirements... 2 Unpacking the Scanner... 3 Taking a Closer Look... 3 Unlocking the Scanner... 4 Shipping scanner... 4 Installing the Scanner Software... 5 Connecting the Scanner to Your Computer... 6 Using the FireWire cable... 6 Using the SCSI cable... 8 Using the USB cable...11 Positioning Reflective Originals Your First Scan Performing Color Calibration The color calibration target Before you calibrate Calibrating your target Loading a profile Specifications Additional Documentation in the CD-ROM Copyright 2001 Microtek International, Inc. I A, December 2001

2 This document provides information on how to install the ScanMaker 9800XL flatbed color scanner and perform basic image scanning procedures. Introduction The ScanMaker 9800XL is a 48-bit color flatbed scanner that supports tabloid-sized (A3 or B-size) scanning for corporate users or designers. This scanner scans images up to 12" x 17" at an optical resolution of 1600 x 3200 dpi (12800 x dpi interpolated). The ScanMaker 9800XL provides three built-in interfaces (FireWire, USB, and SCSI), and allows you to choose any of the three interfaces to digitize image originals. System Requirements 128MB RAM or more recommended CD-ROM drive (for installing software) Color display with 24-bit color output capability FireWire PC - Pentium II or later with built-in FireWire port - Windows 98 SE, 2000, Me, or XP Mac - imac DV or new G3/G4 with built-in FireWire support - Mac OS 9.x USB PC - Pentium PC or later with USB port - Windows 98, 2000, Me, or XP Mac - imac or G3/G4 with built-in USB port - Mac OS 8.6 through 9.x SCSI PC - Pentium PC or later - Windows 95, 98, 2000, Me, XP, or NT 4.0 Mac - Power PC class or later with ASPI compliant SCSI port - Mac OS 8.5 through 9.x 2 ScanMaker 9800XL Installing and Getting Started

3 Unpacking the Scanner Open your scanner package and check the components as stated in your packing list. If any component is missing, call Microtek Customer Service. ScanMaker 9800XL unit FireWire card FireWire cable USB cable Kodak Q-60R1 color target (Reflective) Documentation- includes ScanMaker 9800XL Installing and Getting Started, ScanWizard Pro User's Guide, ScanWizard Pro Quick Reference, Unlock card, and other inserts. Taking a Closer Look Scanner lid Vertical ruler Horizontal ruler READY indicator (Green) POWER indicator (Orange) Power switch Power port SCSI ID switch Accessory port Terminator switch FireWire ports (2) SCSI port (1) USB port (1) ScanMaker 9800XL Installing and Getting Started 3

4 Unlocking the Scanner Your scanner has a locking screw to protect the scanner carriage mechanism during shipping. Before you operate the scanner, you need to disengage the locking screw. 1. Turn the scanner on its side and locate the locking screw at the bottom of the scanner. Unlock 2. Using a flathead screwdriver, turn the locking screw counterclockwise until the screw pushes out and is flush with the bottom of the scanner base. Shipping scanner If you have to transport the scanner, the scanner must be locked. To lock the scanner, follow the steps below: 1. Turn off the scanner if your scanner is on. Lock 2. Set the SCSI ID number to Turn on your scanner. The scanner's carriage will move to standby position in 5 minutes. 4. When the indicators on the front of your scanner stop blinking, turn the locking screw clockwise one-fourth turn while pushing it in simultaneously. The screw should stay in and not pop back out. 5. Turn off your scanner. The scanner is now ready for transport. Note: To use the scanner again at a future time, be sure to reset the SCSI ID to its original number prior to step #2. Otherwise, the scanner ID will be left at SCSI ID 9 and will not work. 4 ScanMaker 9800XL Installing and Getting Started

5 Installing the Scanner Software Before connecting the scanner to your computer, follow the steps below to install the scanner software: 1. Turn on your computer. 2. Insert the Microtek CD-ROM into your CD-ROM drive. For Macintosh users:* When the Microtek CD-ROM icon appears on your Macintosh desktop, doubleclick on this icon to open it. The software installer screen should appear, and click each software program on the screen to install all the software components. Double-click the Install icon on each folder to install the respective programs one at a time. For PC users: The Microtek Scanner Software installer screen should automatically come up. When the software installer screen appears, click each software program in the order that it appears on the screen to install all the software components. When you install ScanWizard Pro, the installer program will install the Color Matching driver program and ask you to perform Color Matching for your monitor and printer. The Color Matching feature ensures color consistency from the initial input phase when an image is captured by the scanner, to the final output process when the image is output to your monitor or printer. Note: If the software installer screen does not come up automatically, doubleclick the following in succession: My Computer on your Windows desktop; the CD-ROM icon; and then cdsetup.exe to start the installer program. 3. Restart your computer when the software installation is complete. *Caution: For Macintosh users, 1. Make sure the additional software you have is already installed in your computer before installing the scanner software. 2. Make sure that all virus protection software is turned off before installing the scanner software. Once the scanner software installation is finished, remember to re-enable the virus protection software. 3. For imac users, please visit Apple's website at to download and install any imac updates you may require. ScanMaker 9800XL Installing and Getting Started 5

6 Connecting the Scanner to Your Computer The ScanMaker 9800XL comes with three built-in interfaces: FireWire, USB, and SCSI. You may choose any of the three interfaces to make the connection between the scanner and computer. (You should use only one interface at a time.) Using the FireWire cable Before connecting the scanner, check to see if your computer system is FireWireready. FireWire-ready means you can connect the scanner to your computer using a provided FireWire cable. System is FireWire-ready For Macintosh users, your computer should have been equipped with a built-in FireWire port. This port should be designated with the FireWire symbol shown to the left. For PC users, the FireWire card should be installed and work properly in your computer. System is Not FireWire-ready If your system is not FireWire-ready, you will need to install a FireWire card. For more details on how to install the FireWire card, please refer to the FireWire Installation Guide on a separate documentation included with your scanner package. Alternatively, you can use the USB or SCSI interface to connect your scanner. For FireWire-ready systems: Follow the steps below to make the FireWire connection. 1. Connect the power cord to your scanner. Plug the power cord into the back of the scanner, and plug the other end into a power source (power surge protector highly recommended). Make sure no other cable is connected to the scanner except the power cord at this point. 6 ScanMaker 9800XL Installing and Getting Started

7 2. Connect the scanner to your computer, using the provided FireWire cable. Connect one end of the FireWire cable to your computer s FireWire port, and connect the other end of the cable to the scanner s FireWire port. For Macintosh users The latest Macintosh computers (i.e., G3, G4, etc.) are equipped with a built-in FireWire port, usually labeled with the logo. For PC users 3. Turn the scanner's power switch to On, and wait for the green light on the scanner's front panel to stop blinking and stay on steady. 4. Your system will detect the scanner automatically. ScanMaker 9800XL Installing and Getting Started 7

8 Using the SCSI cable Before connecting the scanner, check to see if your computer system has a built-in SCSI interface or an installed SCSI card. If you need help on installing the SCSI card, please refer to the SCSI Installation Guide on a separate documentation included with your scanner package, or refer to the documentation that came with the SCSI card. Follow the steps below to make a SCSI connection. 1. Shut down your computer. 2. Set the SCSI ID number to 6. If the SCSI ID number 6 is used by another SCSI device, check which SCSI ID is free, and set the number to a free SCSI ID. Push the minus button (-) above the SCSI ID number to decrease the number; push the plus button (+) to increase the number. 3. Connect the scanner to your computer, using the SCSI cable. Connect one end of the SCSI cable to your computer s SCSI port, and connect the other end of the cable to the scanner s SCSI port. For Macintosh users 8 ScanMaker 9800XL Installing and Getting Started

9 For PC users 4. Set the scanner s terminator switch to the ON position. Note: If you have multiple devices on your SCSI chain, make sure the scanner is the last device on the chain and that the scanner is terminated (i.e., scanner's terminator switch is set to ON). ScanMaker 9800XL Installing and Getting Started 9

10 5. Connect the power cord to your scanner. Plug the power cord into the back of the scanner, and plug the other end into a power source (power surge protector highly recommended). 6. Turn the scanner's power switch to On, and wait for the green light on the scanner's front panel to stop blinking and stay on steady. 7. Turn on your computer; the system will detect the scanner automatically. 10 ScanMaker 9800XL Installing and Getting Started

11 Using the USB cable Before connecting the scanner, check to see if your computer system has a built-in USB port. The latest Macintosh computers (i.e., G3, G4, etc.) are equipped with a built-in USB port, and usually labeled with the USB logo. Follow the steps below to make the USB connection. 1. Connect the power cord to your scanner. Plug the power cord into the back of the scanner, and plug the other end into a power source (power surge protector highly recommended). Make sure no other cable is connected to the scanner except the power cord at this point. 2. Connect the scanner to your computer, using the provided USB cable. Connect one end of the USB cable to your computer s USB port, and connect the other end of the cable to the scanner s USB port. For Macintosh users USB port usually labeled with the logo. ScanMaker 9800XL Installing and Getting Started 11

12 For PC users 3. Turn the scanner's power switch to On, and wait for the lights on the scanner's front panel to stop blinking and stay on steady. 4. Your system will detect the scanner automatically. 12 ScanMaker 9800XL Installing and Getting Started

13 Positioning Reflective Originals 1. Lift the scanner lid. 2. Place the original to be scanned face down on the scanner s glass surface. Center the top of the original along the horizontal ruler on the scanner. If you are scanning a book or thick materials/documents, lift the scanner lid out of its hinge sockets high enough to create room between the originals and the lid. Please note that the calibration window on the glass surface should be kept clear and free from any obstruction during scanning Lower the scanner lid. Note: To scan transparency materials (positive or negative films) with the ScanMaker 9800XL, you should have an optional Transparent Media Adapter (TMA1600). For more details on the TMA1600, contact Microtek Customer Service. ScanMaker 9800XL Installing and Getting Started 13

14 Your First Scan 1. Launch ScanWizard Pro from your image editing application. To do this, choose the Import or Acquire command from the File menu of your image editing application, then select ScanWizard Pro. To operate ScanWizard Pro in the stand-alone "batch" mode in Macintosh systems, go to the Apple menu, and choose the Batch Scan command. In Windows, launch ScanWizard Pro from the Start menu in Windows. The first time you launch ScanWizard Pro, you will be asked to perform Color Matching for your monitor and printer. Monitor selection shown here is set in the ColorSync Control Panel. Color Matching features Immediately updates the Preview window image when a new setting is selected. This will reflect colors consistent with the newly selected profile. 2. Once ScanWizard Pro is launched, go to the Preview window and click the Scan Material icon. From the submenu that appears, choose Reflective. 3. Click the Overview button to start an overview, and you will see the image appear in your Preview window. 14 ScanMaker 9800XL Installing and Getting Started

15 4. Select the Scan Frame tool from the Toolbar in the Preview window, and choose the area to be scanned by dragging a rectangle around it. You will see a flashing frame (marquee) around the selected area Scan Job Queue window Info window 6 Settings Window Preview window 5. Click the Prescan button to start an overview, and you will see the thumbnail image appear in your Scan Job Queue window. 6. To scan a photographic original, bring up the Settings Window, and select None on the Descreen options menu. To scan printed material, on the Descreen options menu select the suitable descreen level (Newspaper, Art Magazine, etc.). 7. If you like what you see in the Preview window, click the Scan button to start scanning. The image is then delivered to your image editing application program, where the image can be saved, printed, or modified further. If you launch ScanWizard Pro in batch mode, you may be asked to input a file name for the scanned image. For more details on various scanning scenarios, refer to the ScanWizard Pro User's Guide included in your scanner package. ScanMaker 9800XL Installing and Getting Started 15

16 Performing Color Calibration The Microtek Scanner ICC Profiler (MSP) is a scanner calibration and profiling utility program exclusively designed for Microtek scanners. Used together with the color calibration target, the ICC Profiler determines the color attributes of your scanner accurately, then generates an ICC profile tailored exclusively for the scanner you are using under ScanWizard Pro. The Microtek Scanner ICC Profiler utility is included in the CD-ROM that contains ScanWizard Pro. Select the Microtek Scanner ICC Profiler option to install. The color calibration target Included in your scanner package is an industry-standard Reflective Kodak color target (Kodak Q-60R1, size 5" x 7"). The calibration target is very delicate and must be handed carefully, as follows: Gently remove the target from its protective sleeve and avoid touching the target image surface. When not in use, keep the target in its sleeve and away from light and heat. Note: To keep the colors in your scanner consistent, you should perform color calibration on a regular basis. Professional photographers, graphic designers or others who require extremely precise color may wish to calibrate the scanner every time it is used. Before you calibrate Before calibration, make sure that the Scanner ICC Profiler program is successfully installed, and that the calibration target is placed on your scanner correctly. Proper positioning of the reflective target on the scanner is important for successful calibration. Incorrect positioning of the target will result in an unsuccessful calibration. 1. Place the target face down on the glass surface of the scanner, making sure that the up side of the target is positioned toward the scanner's front panel and has its edge firmly aligned against the scanner top ruler. 16 ScanMaker 9800XL Installing and Getting Started

17 Using the scanner's top ruler as a reference point, adjust the target position so that it is horizontally in the center of the glass surface Make sure the woman's portrait lies towards the right side of the scanner. Please note that the calibration window on the glass surface should be kept clear and free of any obstruction during scanning. Calibrating your target 1. With the target properly positioned in the scanner, turn on your scanner and let it warm up for about five minutes. 2. Launch the Microtek Scanner ICC Profiler calibration program. In Macintosh, locate the Microtek ICC Profile folder and double-click the ICC Profile icon. In Windows, select the Start menu, Programs, Microtek ScanWizard Pro for Windows, then Microtek Scanner ICC Profiler. 3. The main dialog box appears. Set the appropriate parameters, click the Start Profiling button, then follow the screen instructions to generate your ICC profile. Choose the scanner model you are currently using. Select "Reflective" Select the date code and target type to match your target ScanMaker 9800XL Installing and Getting Started 17

18 4. Give a file name to save the created ICC profile. For details, refer to the help file of your Scanner ICC Profiler program. 5. When done, click the Close button to exit Scanner ICC Profiler program. Loading a profile Once the profile has been produced, follow the steps below to load the profile you just created. 1. Launch ScanWizard Pro. 2. From the Preview window, click the Scan Material icon, and select the Reflective icon. 3. From the Settings window, click on the Scanner Profile list box and select the profile you have just created. 18 ScanMaker 9800XL Installing and Getting Started

19 Specifications Scanning Modes Color, grayscale, and black & white in a single scanning pass 48-bit color input and output (approx. 281 billion colors) 16-bit grayscale (approx. 65,536 shades of gray) Scanning area Resolution Dimensions (L x W x H) Weight Voltage Environment Reflective: 12" x 17" (305 x mm) Optical: 1600 dpi x 3200 dpi Interpolated: dpi x dpi 24.7" x 14.8" x 5.1" ( x x mm) 26.4 lbs (12 kg) AC 100V to 240V, Hz Operating temperature: 50 to 104 F (10 to 40 C) Relative humidity: 20% to 85% Additional Documentation in the CD-ROM Additional documentation is provided in the Microtek CD-ROM that contains ScanWizard Pro, Scanner ICC Profiler, troubleshooting, etc. If you encounter problems with hardware or software, you can open the file that you wish to view with Acrobat Reader or your browser, then read or print the information. ScanMaker 9800XL Installing and Getting Started 19

20 Federal Communications Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Responsible Party: Loi Han 3715 Doolittle Drive Redondo Beach, CA USA Telephone No: Trade Name Model Number ScanMaker 9800XL MRS-3200A3 Tested to Comply With FCC Standards FOR HOME OR OFFICE USE Federal Communications Commission Interference Statement This equipment (Model: MRS-3200A3) has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. Note: A shielded interface cable with ferrite core installed on the scanner connector end must be used with this equipment. Caution: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user's authority to operate the equipment. 20 ScanMaker 9800XL Installing and Getting Started