2kW Quartz Heater Operation Manual

Transcription

1 LEVQ20 2kW Quartz Heater Operation Manual

2 LEVQ20 2kW Quartz Heater Introduction Your infrared heater uses radiant heat to warm people and objects and not the air in between. This is the only method of heating that doesn t blow out or blow away. This heater is specifically designed for outdoor use and is therefore weatherproof. Important Safety Instructions We recommend this appliance is fitted by a suitably qualified installation Engineer/ Electrician. When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, or injury to persons, etc. Read through the operation and assembly instructions thoroughly before fitting and operating the appliance. Be sure to keep the manual in a safe place for future reference. If you pass the appliance on, pass on the instructions too. Check if the voltage indicated on the nameplate of the appliance corresponds to the local mains voltage before you connect the appliance. The power supply to the appliance should correspond to the relevant regulations of the power supply companies and the 17th Edition regulations. Extension cords and multi-sockets may be used only if care is exercised in their use. The marked electrical rating of the extension cord or multi-socket should have adequate current carrying capacity and correspond to the relevant regulations of the power supply companies and the 17th Edition regulations. Check if the voltage indicated on the appliance corresponds to the marked electrical rating of the extension cord or multi-socket before you connect the appliance. Page 2 Specifications Product type: Infrared quartz heater Voltage: V Power Consumption: 2000W Dimensions (W x D x H): 545 x 100 x 125mm Ingress Protection Rating: IP65 Weight: 2.5kg Check the appliance is not located immediately below a wall socket-outlet. Never install this appliance close to anything flammable, such as furniture, curtains, etc. In order to avoid overheating and fire hazard, do not cover or obstruct the appliance. Do not put any of the following materials on the appliance, such as clothes, blanket, pillow, paper etc. A minimum distance of 1 metre between the appliance and flammable materials must always be maintained. The casing and the front cover of the appliance become extremely hot during operation. Pay attention that, no combustible material due to Wind or other environmental influences covers or obstructs the appliance, such as curtains, marquees, flags, plastic foil etc. Do not touch the appliance. Caution! Risk of scald injury! Do not let the cord hang over edge of table or counter, or touch hot surfaces. If the supply cord is damaged, it must be replaced by the manufacturer or a service agent or a similarly qualified person in order to avoid a hazard. In case of improper use, there is a risk of electrical shock and/or fire hazard. Operation of the appliance must be discontinued and the mains plug removed/unplugged immediately. Do not try to repair the appliance by yourself. Please contact with a service agent or a suitably qualified electrician for maintenance.

3 Remove the plug from the power outlet and wait until the appliance has cooled completely before cleaning Do not store any burnable liquids, paint, gas tank etc. in the immediate surroundings of the appliance. Do not use the appliance in flammable ambience (such as near by combustible gas or spray cans) - Danger of explosion and fire! This appliance is NOT intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Keep out of reach of children. In order to keep children from the dangers of electrical appliances, never leave them unsupervised with the heater. Consequently, when selecting the location for your heater, do so in such a way that children do not have direct/indirect access to the heater. Children must always be supervised when the heater is switched on. Caution! Never leave the appliance unsupervised when in use. Do not use the appliance with a programmer, timer or any other device that switches the appliance on automatically. The appliance must only be mounted by an Electrician/Engineer or suitably qualified person, paying attention to the relevant regulations of the power supply companies and the 17th Edition regulations. Installation For additional protection the installation of a residual current device (RCD) is advisable. Remove all package material (including the anti-vibration material of the lamp) and check the appliance, supply cord and the plug for signs of damage. Pay attention to the mounting position, place and all mounting materials (Anchor plugs, screws etc). Ensure they are suitable and stable enough for mounting and are strong enough to support the weight of the heater. Before mounting, the minimum safe mounting distances and tilt angles shown below must be strictly followed. 1. The distance between the bottom edge of the heater and the floor must be at least 1.8 metres. 2. There must be a distance of at least 0.2 metres between the heater and the ceilings, roofs or other covers. Pay attention that, the installation site of the heater, will not add excessive wind load. Fix the mounting bracket on the wall first. Ensure that the place to be installed is secure and firm and will take the weight of the heater. See figure 3. Adjust the desired angle of radiation and tighten all screws. Regularly check all screws for tightness. Mechanical bearing pressure, vibration and oscillation due to wind or rain could lead the screws to loosen. Plug in the power source. Then observe, whether during the first minutes the appliance works trouble-free. 3. There must be a distance of at least 0.5 metres at each side between the heater and walls or the like. See figure Recommended degree to mounting surface is 45. See figure 2. Page 3

4 Figure 1: Minimum distance to floor, ceiling and wall. Figure 2: Tilt angle. Minimum 0.2 metre Minimum 1.8 metres Minimum 0.5 metre Recommended Maximum Tilt 45 Figure 3: Mounting bracket (wall bracket) and anchor plugs provided. Connection from the wall to the infrared heater. Page 4

5 Lamp Replacement Must be performed by an electrician or similarly competent person. Always ensure the heater is disconnected from the mains power source before attempting any maintenance. Step 1: Loosen retaining screws and remove both side plates. Step 2: Disconnect wires and remove left and right sub shells. Step 3: Pull out the connecting wire. Step 4: Remove fixed plate from the opposite end, then pull out the old lamp. Page 5

6 Step 5: Remove protective cover and straighten each end. Step 6: Disconnect old lamp. Step 7: Replace new lamp as shown below. Step 8: Fix the lamp into the main shell. Step 9: Insert metal tube through main shell. Page 6

7 Step 10: Insert wire through metal tube and pull through from other side. Step 11: Slide protective cover into place and bend each end back down. Step 12: Reconnect wires, then fix sub shells back onto the main shell. Step 13: Refix side plates and tighten screws. The job is now complete. Page 7

8 Cleaning and Maintenance This heater is consist of a robust and maintenance-free aluminium casing with a protection cover. No user serviceable parts inside. Before cleaning, remove the plug from the power outlet and wait until the heater has completely cooled down. Wipe the heater ONLY with a clean and lintfree cloth or a soft brush. Never use abrasive cleaners, scrubbing brushes and chemical cleaners for cleaning! You can use alcohol sparingly to clean the heater. To protect against electrical shock and danger of life, do not immerse cord, plug, or any part of the heater in water or other liquid. For heating element replacement, please contact the manufacturer or a service agent or a similarly qualified person. Disposal In accordance with European Directive 2002/96/EG concerning waste electrical and electronic equipment (WEEE), please return any electrical equipment that you will no longer use to the collection points provided for their disposal. This symbol indicates that the appliance cannot be treated as normal domestic waste, but must be handed to a collection point for where electric and electronic appliances are recycled Information concerning where the equipment can be disposed of can be obtained from your local authority. Customer Service Repairs must be carried out by authorised specialists, thus ensuring electrical safety. Please contact a service agent or a suitably qualified electrician. Improper repairs could lead to danger to the user. This warranty does not cover damage of failure which results from alteration, accident, misuse, abuse, neglect, commercial use or improper maintenance. In line with our policy of continuous product development we reserve the right to change the product and documentation specifications without notice. Page 8 LEV0017b/Issue 1/July 2012