Stroller Model # IMPORTANT! RETAIN FOR FUTURE REFERENCE

Transcription

1 Stroller Model # IMPORTANT! RETAIN FOR FUTURE REFERENCE

2 Safety Precautions Read all instructions before assembly and use of the stroller. Keep instructions for future use. WARNING TO AVOID INJURY OR DEATH: ALWAYS APPLY THE BRAKES WHENEVER THE STROLLER IS PARKED. DO NOT LEAVE CHILDREN UNATTENDED. SECURE THE CHILD IN THE HARNESS AT ALL TIMES. DO NOT CARRY EXTRA CHILDREN OR BAGS ON THIS STROLLER. MAKE SURE CHILDREN ARE CLEAR OF ANY MOVING PARTS IF YOU ADJUST THE STROLLER. TO AVOID INJURY ENSURE THAT YOUR CHILD IS KEPT AWAY WHEN FOLDING AND UNFOLDING THE STROLLER. ENSURE THAT ALL LOCKING DEVICES ARE ENGAGED BEFORE USE. USE THE TETHER STRAP TO STOP THE STROLLER ROLLING AWAY. DO NOT USE THIS BASSINET ONCE THE CHILD CAN SIT UP UNAIDED. BE AWARE THAT MOVING PARTS MAY CAUSE INJURY IF CARE IS NOT TAKEN. Fingers or parts of the body could be injured when the stroller is being folded or unfolded. Please use caution when folding or unfolding the stroller. Always check that safety locks are engaged before placing a child in the stroller. Ensure your child is secured with a correctly adjusted safety harness. Do not allow children to stand on the seat. Do not hang bags or goods from the handle as this could cause the stroller to tip over. Do not place more than 5kgs in the basket or 1kg in the hood pocket (if supplied). The weight of the child using the product should not exceed 20kgs. The height of the child using the product should not exceed 96cm. It is unsafe to use parts other than those approved by the manufacturer. Never ride with more than one child in the stroller. This stroller has been designed for use on flat or gently sloped surfaces. Using this stroller on uneven or higher sloped surfaces may cause the stroller to become unstable and tip over. Regularly inspect all parts and locking devices, promptly replace worn out or broken parts. Remove the child from the stroller before going up or down stairs and escalators. To prevent the risk of the stroller catching fire, do not park it near an open fire, heater or barbeque. Do not make any changes or alterations to this product, unless through an approved service agent. To avoid the risk of suffocation, keep all plastic packaging materials out of reach of children. Never leave safety harness connected when not fitted to a child in the stroller as this may create loops that could cause a strangulation hazard. Ensure the storage latch is fully engaged when lifting or carrying the stroller Congratulations on your purchase of the Vogue Childcare Stroller This product has been designed and developed with safety, comfort and functionality in mind. Please take the time to read this manual carefully before using this product and keep it in a safe place for future reference. Contents Assembly contents list Assembly / Operating instructions How to care for your Vogue Childcare Stroller Due to variations in the style and design of our products, the photographs and illustrations shown in this instruction manual are generic, therefore product fabrics, colour and design may vary from images shown. CNP Brands reserves the right to alter product specifications without notice as a result of our ongoing policy of product improvement. 03

3 Check what you have received... You have received 1 box. Please check the contents of the box against the list below. If anything is missing, please contact Customer Service. In Australia, contact CNP Brands on , in New Zealand contact Wainhouse Distribution on Supplied loose in box: Canopy x 2 Carry cot/seat unit x 1 Bumper x 1 Frame x 1 Left car seat adapter (marked on the inside with L ) x 1 Front swivel wheels x 2 Right car seat adapter (marked on the inside with R ) x 1 Boot cover x

4 Front swivel wheels assembly 1. Line up the front wheels with the bottom of the frame. Using the rear brakes 1. To lock the brakes, push down on the brakes on the rear axle with foot. Ensure that both brakes are engaged 2. Push firmly until the wheel clicks into place. Repeat with other side. Ensure wheels are both clicked firmly into place. 2. To unlock brakes, lift the brakes on the rear wheels with foot. Ensure both brakes are disengaged. Swivel function 1. To lock swivel wheels, push lever outwards. WARNING: Always apply brakes when parking stroller. 2. To unlock swivel wheels, push lever inwards. Removing the front wheels 1. Push in the quick release tab, then pull the wheel out of the wheel - housing. WARNING: On unmade or uneven surfaces all swivels must be locked

5 Unfolding the stroller 1. Using your thumb, push the lock outward to release the stroller (highlighted in the image). Attaching the seat 1. Slide both sides of the seat into the frame until you hear each side click into position. 2. Lift up the stroller by the handle and move forward simultaneously until the stroller opens and clicks into position. 2. Once the seat is in position, pull up to confirm it is secure. Assembling seat 1. Turn bassinet upside down, lift rear bar. Adjusting seat position. 1. The seat can be adjusted to different positions. Push the buttons in simultaneously and move the seat to the desired position. 2. Wrap velcro fabric around the bar and press down firmly to secure

6 Attaching the bumper bar Attaching the canopy 1. Insert front bumper bar into openings on the sides of the seat. Push gently until you hear a click on both sides. 1. Slide each side of the canopy onto the frame mould in each side until it clicks into place. WARNING: The bumper is only used for the seat unit; do not use it for carrying the carry cot._ 2. Loop the elastic over the area that is circled in the image to the right on both sides of the canopy. Removing the bumper bar 1. Squeeze the buttons on the side of the bumper bar as per image. Pull outwards from seat. 3. Ensure the 2 press studs are pushed in at the back of the canopy to secure the canopy in place

7 Canopy functions Canopy window 1. Pull the canopy cover forward or push backward. 1. When window is not in use, keep the flap secure with the velrco pads. 2. To use the window, roll up neatly and secure with toggle and elastic. 2. Pull out the visor as per image for the sun visor function. Mesh canopy extension 1. To extend mesh extension, unzip zipper around middle of canopy and pull forward. Close zip when not in use. CAUTION: The canopy must be fully closed before folding the stroller. Disassembly / Assembly of canopy 1. To assemble the canopy, attach the canopy clips to each side of the stroller frame (as pictured) by pushing the clips until they snap into place. 2. Attach the press studs to the bar underneath to hold the canopy into place. 3. To disassemble the canopy, repeat the steps above in reverse

8 Boot cover Bassinet Mode - Facing Baby 1. Wrap the boot cover around the bottom end of the bassinet or seat. Attach press studs as shown in image. Match to the press studs on the inside of the boot cover as shown. 2. Insert the top flap of the boot cover underneath the bumper bar so it sits on top of the boot cover. 3. Push firmly on the press studs of both sides to secure it into place. WARNING: Always remove boot cover before folding the stroller. Tether strap Ensure tether strap is used at all times. Make sure your hand is fed through the loop as shown in the diagram. Recommended for newborn to approximately 6 months of age or 9kgs. WARNING: Bassinet cannot stand alone. WARNING: Do not use this bassinet once the child can sit up unaided. To assemble bassinet 1. Loosen the seat adjusting adjuster straps under the backrest. Extend handle 1. Squeeze the handle in the middle of the bar to release the mechanism. Move handlebar to desired position

9 Stroller Mode 2. Push the buttons on the stroller frame simultaneously and move the seat to a parallel position until it clicks into position. 3. Unclip the fasteners at the footrest end of the bassinet and also underneath the seat, as per image. 4. The bassinet mode is now ready. The boot cover can also be attached in this mode. To convert to a stroller 1. Push the buttons on the stroller frame simultaneously and move the seat upright until it clicks into position. 2. Hold both straps of the seat adjuster and pull outward to desired position

10 Restraints - Harness 3. Buckle the strap under the front of the bassinet and also the footrest at the end of the bassinet. WARNING: Do not adjust backrest whilst the child is in the stroller Adjusting the backrest This stroller has an adjustable backrest. The upright position on the backrest is not suitable for use with children less than six months old. For use with a newborn (0-6mths), the seat should be fully reclined. The backrest should only be adjusted to a more upright position as the child grows older and is able to support their head without assistance. Declining the seat adjuster 1. To secure the child in the harness, place left hand buckle prong (b) on top of (a). 2. Hold both left hand buckle prongs (a) and (b) together and insert it into buckle housing (e) until it snaps into position. 3. Repeat previous steps for right hand buckle prongs (c) and (d). 4. Once all attached, carefully adjust the harness straps by pulling each slider (f) until the desired fit is achieved in the lap, shoulder and crotch straps. 5. To release the buckles, squeeze the top and bottom prongs (a) and (b), (c) and (d) together until harness disengages. CAUTION: Always adjust the harness when changing the seating position of the child. f f a c f b d e f (a), (b): Left hand buckle prongs (c), (d): Right hand buckle prongs (e): Buckle housing (f): Strap adjustment sliders f 1. To decline the seat adjuster, press and pull adjusting straps in a downward motion and lower to desired position. To adjust waist strap 2. To incline the seat adjuster; hold both straps and pull outward to desired position. CAUTION: Do not adjust the backrest while child is in the stroller. 1. To loosen waist strap, push up both top and bottom straps through buckle. 2. To place waist strap in desired position, slide the bottom strap into position then pull the top strap and tighten into position. Inclining the seat adjuster WARNING: Use this harness at all times

11 IMPORTANT: This adaptor is designed for Maxi Cosi Car Seat; to be used with the following strollers: bebe care Rverse / Rverse XT / Rverse XLR / Childcare Vogue Car Seat Adapter To remove car seat from stroller frame 1. Simultaneously swing the car seat s handle up while pressing both grey levers on the car seat side handle moulds to release the car seat. 2. Lift up car seat via the handle. 1. Remove the seat from the frame of the stroller. Insert the set of plastic adapters into the slots where the seat normally sits in position. Push gently until the adapters click and lock into place. The left adapter should be placed on the left when facing the stroller from the front, and the right adapter on the right when facing the stroller from the front. Folding stroller NOTE: Both plastic adaptors can remain attached to the stroller frame when folding stroller. Fold the stroller as per stroller manufacturer s folding instructions. Insert car seat into adaptor 1. Insert the Maxi Cosi car seat as per car seat manufacturer s instructions by aligning the plastic side parts of the car seat into the corresponding adaptor. 2. Push the car seat down until it clicks into place. 3. Swing the car seat s handle down while pressing both grey levers on the car seat side handle moulds until it locks into position. 4. Car seat can be attached to stroller frame in either forward facing or reverse facing. 5. To rotate car seat in opposite direction; rotate the car seat together with the adaptors and insert them into the side stroller frame s slots until it clicks and locks into place. WARNING: Lift the Maxi Cosi Car Seat upwards to ensure that it is fully engaged and locked before use. To remove adaptor To release the set of plastic adaptor from stroller, slide the red buttons on the side of the plastic adaptor and lift them out of the stroller frame slots. Tether strap Ensure tether strap is used at all times. Make sure your hand is fed through the loop as shown

12 Folding the stroller 1. To fold the stroller, pull the levers upwards on both sides of the stroller frame simultaneously to disengage the stroller frame. Cleaning To ensure the long-lasting use of your stroller, dry it with a soft absorbent cloth after use in rainy weather. Use a damp cloth to clean the frame. Do not use abrasive cleaners. After using your stroller on the beach, clean the frame and wheels thoroughly with water to remove the sand and salt. Allow it to dry thoroughly. Removable and non-removeable fabric covers and trims maybe cleaned using a damp cloth with soap or mild detergent. Allow it to dry completely before folding or storing it away. Do not dry clean, or use bleach on fabrics or trims. Do not machine wash, tumble or spin dry, unless the care labelling on the product permits these methods. 2. Push handle forward to the front wheels. The stroller should collapse onto itself. Maintenance Check stroller regularly to ensure that locking devices and components are secure and working properly. Always check parts regularly for tightness of screws, nuts and other fasteners tighten or replace if required. To maintain the safety of your stroller, seek prompt repairs for bent, torn, worn or broken parts. Use only those parts and accessories approved by CNP Brands. If the wheels squeak, use silicone based spray or light oil ensuring it penetrates the wheel and axle assembly. To prevent mould or mildew, do not fold or store the product if it is damp or wet. Allow it to dry thoroughly. Always store the product in a well ventilated area and away from direct sunlight. 3. Lift cental bar upwards by the handle to collapse unit. If you have any difficulties in assembling the stroller, please contact our Service Department. In Australia, contact CNP Brands on , in New Zealand contact Wainhouse Distribution on Ensure the stroller is secure and locked into place with the locking mechanism. Ensure hood is folded inwards

13