2 Ton Underhoist Safety Stand

Size: px

Start display at page:

Download "2 Ton Underhoist Safety Stand"

Edith Rice
7 years ago
Views:

Model 41860 2 Ton Underhoist Safety Stand Set up And Operating Instructions Diagrams within this manual may not be drawn proportionally.

1 Model Ton Underhoist Safety Stand Set up And Operating Instructions Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Distributed exclusively by Harbor Freight Tools Mission Oaks Blvd., Camarillo, CA Visit our website at: Read this material before using this product. Failure to do so can result in serious injury. Save this manual. Copyright 2007 by Harbor Freight Tools. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions or replacement parts, please call

2 Assembly Assembly of Legs (#8), Down Supports (#9), and Mid Supports (#16). 1. The top of each Leg (#8) has a closed end with a hole drilled in it. Attach a Down Support (#9) to the bottom hole on a Leg (#8) using a Bolt (#12), a Washer (#14), and a Nut (#13). Make sure you attach to the inside of the angle iron on the Leg (#8). Do not fully tighten yet. 2. Move up the same Leg (#8) to the middle hole and attach a Mid Support (#16) using a Bolt (#12), a Washer (#14), and a Nut (#13). 3. Next, repeat the process adding a second Down Support (#9) and a Mid Support (#16) to the leg you just assembled. 4. You should now have one Leg (#8) with two Down Supports (#9) and two Mid Supports (#16). Take both remaining Legs (#8) and attach them to Down Supports (#9), and Mid Supports (#16) on the previously assembled Leg (#8). 5. Next, put the last Down Support (#9) and Mid Support (#16) between the two remaining Legs (#8). Tighten all of the Nuts (#13) and Bolts (#12). 6. The Upper Supports (#15) are L shaped with one end shorter than the other. Attach the shorter end to the upper holes on the Legs (#8) of the tripod you just constructed using a Bolt (#12), a Washer (#14), and a Nut (#13), for each Upper Support (#15). See the Assembly Diagram on Page 4 to show correct position of each Upper Support (#15). 7. The Base Stand (#7) has two metal triangles welded to the top section of it, below the Lock Pin (#11) hole. Lower the Base Stand (#7) into the tripod you just constructed, bottom first. The lower triangle should rest on top of the Upper Supports (#15), lining up with the holes of both the Upper Supports (#15) and the holes on the triangle. The upper triangle should rest on top of each Leg (#8), lining up the holes in the triangles with the holes on the end of each Leg (#8). Secure the bottom triangle to the Upper Supports (#15) using a Bolt (#12), a Washer (#14), and a Nut (#13). Repeat the process securing the upper triangle to each Leg (#8) using a Bolt (#12), Washer (#14), and a Nut (#13). 8. Part numbers 2,3,4,5, and 6 come pre-assembled. The Pan (#1) and the Handles (#10) must be added to the Shaft (#6) assembly. Set the Pan (#1) on top of the Screw Rod (#2) and attach it with a Bolt (#12). Next, screw each Handle (#10) into the threaded holes on the Bearing (#4). 9. Take the assembled Shaft (#6) and insert it into the tube of the Base Stand (#7). Lower it to the desired level and insert the Lock Pin (#11) to secure it at the appropriate height. SKU Page 2

3 General Usage This Stand is used to support automobile exhaust systems and drive shafts underneath an already hoisted vehicle. The Stand will allow hands free repair after the required part is supported. Note!! The Two Ton High Jack Stand is 24 wide and can be used at a minimum height of 49 3/4 and a maximum height of 93 1/2. Safety Warnings Use for intended purposes only. Use on flat, level, hard surface capable of supporting stand and load. Inspect before use; do not use if parts loose or damaged. Do not exceed 4,000 lb. maximum weight capacity. Wear ANSI-approved safety goggles and heavy-duty work gloves during use. Read manual before set up and/or use. Make sure the hoist used to lift the car or truck is in good working order and securely locked into place after reaching desired height. Operation The Legs (#8) of the High Jack Stand must stand on a dry, clean, hard, level surface. 1. Turn the Handles (#10) so that the Pan (#10) retracts back into the Screw Rod (#2) as far as it will go. 2. Position the Pan (#10) directly underneath the auto part you wish to support. 3. Remove the Lock Pin (#11) and raise the Shaft (#6) so that the Pan (#1) rests under the selected auto part needing support. Reinsert the Lock Pin (#11). 4. Turn the Handles (#10) raising the Pan (#1) until it securely supports the auto part. Make sure there is no wobble. If necessary tighten Handles (#10). SKU REV 07k Page 3

4 Assembly Drawing and Parts List No Description Qty 1 Pan 1 2 Screw Rod 1 3 Screw Nut 1 4 Bearing 1 5 Position Rod 1 6 Shaft 1 7 Base Stand 1 8 Legs 3 9 Down Support 3 10 Handle 2 11 Lock Pin 1 12 Bolt M10x Nut M Washer # Upper Support 3 16 Mid Support 3 SKU Page 4

5 LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. This warranty is expressly in lieu of all other warranties, express or implied, including the warranties of merchantability and fitness. To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product. This warranty gives you specific legal rights and you may also have other rights which vary from state to state Mission Oaks Blvd. PO Box 6009 Camarillo, CA (800) PLEASE READ THE FOLLOWING CAREFULLY The manufacturer and/or distributor has provided the parts list and assembly diagram in this manual as a reference tool only. Neither the manufacturer or distributor makes any representation or warranty of any kind to the buyer that he or she is qualified to make any repairs to the product, or that he or she is qualified to replace any parts of the product. In fact, the manufacturer and/or distributor expressly states that all repairs and parts replacements should be undertaken by certified and licensed technicians, and not by the buyer. The buyer assumes all risk and liability arising out of his or her repairs to the original product or replacement parts thereto, or arising out of his or her installation of replacement parts thereto. SKU REV 07k Page 5

OAK WORKBENCH WITH 2 DRAWERS

OAK WORKBENCH WITH 2 DRAWERS Model 93991 ASSEMBLY Instructions Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury.