RoHS Compliant. msata mini H1 Product Specifications. January 28, Version 1.0. Apacer Technology Inc.

Transcription

1 RoHS Compliant msata Flash Drive msata mini H1 Product Specifications January 28, 2016 Version 1.0 Apacer Technology Inc. 1F, No.32, Zhongcheng Rd., Tucheng Dist., New Taipei City, Taiwan, R.O.C Tel: Fax:

2 Features: Compliance with SATA Revision 3.1 SATA 6.0 Gbps interface Backward compatible with SATA 1.5/3.0 Gbps interfaces ATA command set Capacity 1, 2, 4, 8, 16, 32 GB Performance* Interface burst read/write: 600 MB/sec Sustained read: up to 65 MB/sec Sustained write: up to 50 MB/sec Flash Management Built-in hardware ECC Wear leveling Bad block management S.M.A.R.T. Power failure management TRIM NAND Flash Type: SLC Endurance 1GB:78 TBW 2GB:154 TBW 4GB:310 TBW 8GB: 620 TBW 16GB: 1,231 TBW 32GB: 2,868 TBW Temperature Range Operating: Standard: 0 C to 70 C Extended: -40 C to 85 C Storage: -40 C to 100 C Supply Voltage 3.3 V ± 5% Power Consumption* Active mode: 330 ma Idle mode: 100 ma Form Factor msata mini, JEDEC MO-300B Dimensions (29.85 x x 1.00**, unit: mm) Connector 52-pin msata signal connector RoHS Compliant Device Sleep (optional) Thermal Sensor (optional) *Varies from capacities. The values addressed here are typical and may vary depending on host system settings. **Only the height of the PCB 1

3 Table of Contents 1. Product Description Introduction Capacity Specifications Performance Pin Assignments Software Interface Command Set S.M.A.R.T Flash Management Error Correction/Detection Bad Block Management Wear Leveling Power Failure Management TRIM Secure Erase SATA Power Management Environment Specifications Environmental Mean Time Between Failures (MTBF) Certification and Compliance Endurance Electrical Characteristics Operating Voltage Power Consumption Mechanical Specifications Dimensions Product Ordering Information Product Code Designations Valid Combinations

4 1. Product Description 1.1 Introduction Apacer msata mini H1 delivers all the advantages of flash disk technology with the Serial ATA 6.0 Gbps interface and is fully compliant with the standard msata mini form factor, known as JEDEC MO-300B standard. The module is designed to operate at optimal efficiency and reliability while maintained in super compact form factor. Meanwhile, the power consumption of the msata mini module remains at minimal level. 1.2 Capacity Specifications Table 1-1 Capacity Specifications Capacity Total Bytes Cylinders Heads Sectors Max LBA 1 GB 1,011,032,064 15, ,974,672 2 GB 2,011,226,112 15, ,928,176 4 GB 4,011,614,208 15, ,835,184 8 GB 8,012,390,400 15, ,649, GB 16,013,942,784 16, ,277, GB 32,017,047,552 16, ,533,296 *Display of total bytes varies from file systems. **Cylinders, heads or sectors are not applicable for these capacities. Only LBA addressing applies. LBA count addressed in the table above indicates total user storage capacity and will remain the same throughout the lifespan of the device. However, the total usable capacity of the SSD is most likely to be less than the total physical capacity because a small portion of the capacity is reserved for device maintenance usages. 1.3 Performance Performance of msata mini H1 is shown in Table 1-2. Table 1-2 Performance Specifications Capacity Performance 1 GB 2 GB 4 GB 8 GB 16 GB 32 GB Sustained Read (MB/s) Sustained Write (MB/s) Note: Performance varies from flash configurations or host system settings. 3

5 1.4 Pin Assignments Figure 1-2 Apacer msata mini H1 Pin Assignment Table 1-3 Pin Assignment Description Pin # msata Pin Description 1 NC No Connect V 3.3V Source 3 NC No Connect 4 DGND Digital GND 5 NC No Connect 6 NC No Connect 7 NC No Connect 8 NC No Connect 9 DGND Digital GND 10 NC No Connect 11 NC No Connect 12 NC No Connect 13 NC No Connect 14 NC No Connect 15 DGND Digital GND 16 NC No Connect 17 NC No Connect 18 DGND Digital GND 19 NC No Connect 20 NC No Connect 4

6 Pin # msata Pin Description 21 SATA GND SATA Ground Return Pin 22 NC No Connect 23 +B Host Receiver Differential Signal Pair V 3.3V Source 25 -B Host Receiver Differential Signal Pair 26 SATA GND SATA Ground Return Pin 27 SATA GND SATA Ground Return Pin 28 NC No Connect 29 SATA GND SATA Ground Return Pin 30 NC No Connect 31 -A Host Transmitter Differential Signal Pair 32 NC No Connect 33 +A Host Transmitter Differential Signal Pair 34 DGND Digital GND 35 SATA GND SATA Ground Return Pin 36 NC No Connect 37 SATA GND SATA Ground Return Pin 38 NC No Connect V 3.3V Source 40 DGND Digital GND V 3.3V Source 42 NC No Connect 43 NC No Connect 44 NC No Connect or Device Sleep* 45 Vendor Vendor specific 46 NC No Connect 47 Vendor Vendor specific 48 NC No Connect 49 DAS Device activity signal 50 DGND Digital GND 51 GND Default connect to GND V 3.3V Source *Device Sleep is optional 5

7 2. Software Interface 2.1 Command Set Table 2-1 summarizes the ATA commands supported by msata mini H1. Table 2-1 Command Set Command Code Command Code NOP 00h Idle 97h Data Set Management 06h Check Power Mode 98h Recalibrate 10f-1Fh Sleep 99h Read Sectors 20h SMART B0h Read Sectors without Retry 21h Device Configuration B1h Read Sectors EXT 24h Read Multiple C4h Read DMA EXT 25h Write Multiple C5h Read Native Max Address EXT 27h Set Multiple Mode C6h Read Multiple EXT 29h Read DMA C8h Read Log EXT 2Fh Read DMA without Retry C9h Write Sectors 30h Write DMA CAh Write Sectors Without Retry 31h Write DMA without Retry CBh Write Sectors EXT 34h Write Multiple FUA EXT CEh Write DMA EXT 35h Standby Immediate E0h Set Native Max Address EXT 37h Idle Immediate E1h CFA Write Sectors without erase 38h Standby E2h Write Multiple EXT 39h Idle E3h Write DMA FUA EXT 3Dh Read Buffer E4h Write Long EXT 3Fh Check Power Mode E5h Read Verify Sectors 40h Sleep E6h Read Verify Sectors without Retry 41h Flush Cache E7h Read Verify Sectors EXT 42h Write Buffer E8h Write Uncorrectable EXT 45h Flush Cache EXT EAh Read FPDMA Queued 60h Identify Device ECh Write FPDMA Queued 61h Set Features EFh Seek 70h-7Fh Security Set Password F1h Execute Device Diagnostic 90h Security Unlock F2h Initialize Device Parameters 91h Security Erase Prepare F3h Download Microcode 92h Security Erase Unit F4h Download Microcode DMA 93h Security Freeze Lock F5h Standby Immediate 94h Security Disable Password F6h Idle Immediate 95h Read Native Max Address F8h Standby 96h Set Max Address F9h Note. Security command will only be workable when device runs in non-opal compliant mode. 6

8 2.2 S.M.A.R.T. SMART, an acronym for Self-Monitoring, Analysis and Reporting Technology, is an open standard that allows a hard disk drive to automatically detect its health and report potential failures. When a failure is recorded by SMART, users can choose to replace the drive to prevent unexpected outage or data loss. Moreover, SMART can inform users of impending failures while there is still time to perform proactive actions, such as copy data to another device. 7

9 3. Flash Management 3.1 Error Correction/Detection Flash memory cells will deteriorate with use, which might generate random bit errors in the stored data. Thus, this msata SSD module applies the BCH ECC Algorithm, which can detect and correct errors occur during Read process, ensure data been read correctly, as well as protect data from corruption. This device can correct up to 72bit/1K data. 3.2 Bad Block Management Bad blocks are blocks that include one or more invalid bits, and their reliability is not guaranteed. Blocks that are identified and marked as bad by the manufacturer are referred to as Initial Bad Blocks. Bad blocks that are developed during the lifespan of the flash are named Later Bad Blocks. Apacer implements an efficient bad block management algorithm to detect the factory-produced bad blocks and manages any bad blocks that appear with use. This practice further prevents data being stored into bad blocks and improves the data reliability. 3.3 Wear Leveling NAND Flash devices can only undergo a limited number of program/erase cycles, and in most cases, the flash media are not used evenly. If some areas get updated more frequently than others, the lifetime of the device would be reduced significantly. Thus, Wear Leveling technique is applied to extend the lifespan of NAND Flash by evenly distributing write and erase cycles across the media. Apacer provides advanced Wear Leveling algorithm, which can efficiently spread out the flash usage through the whole flash media area. Moreover, by implementing both dynamic and static Wear Leveling algorithms, the life expectancy of the NAND Flash is greatly improved. 3.4 Power Failure Management Power Failure Management plays a crucial role when experiencing unstable power supply. Power disruption may occur when users are storing data into the SSD. In this urgent situation, the controller would run multiple flush cycles to store the metadata for later block rebuilding. This urgent operation requires about several milliseconds to get it done. At the next power up, the firmware will perform a status tracking to retrieve the mapping table and resume previously programmed NAND blocks to check if there is any incompleteness of transmission. 3.5 TRIM TRIM is a feature which helps improve the read/write performance and speed of solid-state drives (SSD). Unlike hard disk drives (HDD), SSDs are not able to overwrite existing data, so the available space gradually becomes smaller with each use. With the TRIM command, the operating system can inform the SSD which blocks of data are no longer in use and can be removed permanently. Thus, the SSD will perform the erase action, which prevents unused data from occupying blocks all the time. 3.6 Secure Erase Secure Erase is a standard ATA command and will write all 0xFF to fully wipe all the data on hard drives and SSDs. When this command is issued, the SSD controller will empty its storage blocks and return to its factory default settings. Note. Secure erase command belongs to ATA security command. 8

10 3.7 SATA Power Management By complying with SATA 6.0 Gb/s specifications, the msata SSD supports Device Sleep power state: Device Sleep (DevSleep or DEVSLP): PHY powered down; power consumption 5 mw; host assertion time 10 ms; exit timeout from this state 20 ms (unless specified otherwise in SATA Identify Device Log). Note: Device Sleep mode is optional, depending on product ordering selections. 9

11 4. Environment Specifications 4.1 Environmental Environment Temperature Table 4-1 Environmental Specifications Specifications 0 C to 70 C (Standard); -40 C to 85 C (Extended) -40 C to 100 C (in storage) Shock 1,500G, 0.5ms 20Hz~80Hz/1.52mm (frequency/displacement) Vibration 80Hz~2000Hz/20G (frequency/displacement) X, Y, Z axis/60mins each Drop 80cm free fall, 6 face of each Bending 50N, hold 1min/5times Torque 0.5N-m or 5deg, hold 5min/5times ESD Pass Note: Shock and Vibration specifications are subject to change without notice. 4.2 Mean Time Between Failures (MTBF) MTBF, an acronym for Mean Time Between Failures, is a measure of a device s reliability. Its value represents the average time between a repair and the next failure. The measure is typically in units of hours. The higher the MTBF value, the higher the reliability of the device. The predicted result of this msata device is higher than 2,000,000 hours. 4.3 Certification and Compliance msata mini H1 complies with the following standards: SATA Revision 3.1 RoHS ATA/ATAPI FCC CE BSMI MIL-STD-810G 10

12 4.4 Endurance The endurance of a storage device is predicted by TeraBytes Written based on several factors related to usage, such as the amount of data written into the drive, block management conditions, and daily workload for the drive. Thus, key factors, such as Write Amplifications and the number of P/E cycles, can influence the lifespan of the drive. Capacity TeraBytes Written 1 GB 78 2 GB GB GB GB 1, GB 2,868 Notes: The measurement assumes the data written to the SSD for test is under a typical and constant rate. The measurement follows the standard metric: 1 TB (Terabyte) = 1,000 GB. The estimated values are based on JEDEC Enterprise endurance workload comprised of random data with the payload size distribution with sequential write behavior. 11

13 5. Electrical Characteristics 5.1 Operating Voltage Table 5-1 lists the supply voltage for msata mini H1. Table 5-1 Operating Voltage Parameter Conditions Supply Voltage 3.3V ±5% 5.2 Power Consumption Table 5-2 lists the power consumption for msata mini H1. Table 5-2 Power Consumption (typical) Capacity Mode 1 GB 2 GB 4 GB 8 GB 16 GB 32 GB Active (ma) Idle (ma) Note: Power consumptions may vary depending on host system settings. 12

14 6. Mechanical Specifications 6.1 Dimensions Unit: mm Tolerance: ±

15 Unit: mm Tolerance: ±

16 7. Product Ordering Information 7.1 Product Code Designations AP M x x x G N 1 A N X T X N: Standard Flash Type T: Toshiba SLC FW Version F: no DEVSLP G: DEVSLP Operating Temperature Range Blank: Standard Temperature W: Extended Temperature A: Standard Solution Version Form Factor N: msata mini H1 Capacity 001G = 01GB 002G = 02GB 004G = 04GB 008G = 08GB 016G = 16GB 032G = 32GB msata Apacer Product Code 15

17 7.2 Valid Combinations Standard Temperature (0 C to 70 C) Capacity No DEVSLP DEVSLP 1GB APM001GN1AN-FT APM001GN1AN-GT 2GB APM002GN1AN-FT APM002GN1AN-GT 4GB APM004GN1AN-FT APM004GN1AN-GT 8GB APM008GN1AN-FT APM008GN1AN-GT 16GB APM016GN1AN-FT APM016GN1AN-GT 32GB APM032GN1AN-FT APM032GN1AN-GT Extended Temperature (-40 C to 85 C) Capacity No DEVSLP DEVSLP 1GB APM001GN1AN-FTW APM001GN1AN-GTW 2GB APM002GN1AN-FTW APM002GN1AN-GTW 4GB APM004GN1AN-FTW APM004GN1AN-GTW 8GB APM008GN1AN-FTW APM008GN1AN-GTW 16GB APM016GN1AN-FTW APM016GN1AN-GTW 32GB APM032GN1AN-FTW APM032GN1AN-GTW Note: Valid combinations are those products in mass production or will be in mass production. Consult your Apacer sales representative to confirm availability of valid combinations and to determine availability of new combinations. 16

18 Revision History Revision Description Date 1.0 Official release 1/28/

19 Global Presence Taiwan (Headquarters) U.S.A. Japan Europe China India Apacer Technology Inc. 1F., No.32, Zhongcheng Rd., Tucheng Dist., New Taipei City 236, Taiwan R.O.C. Tel: Fax: Apacer Memory America, Inc Lakeview Blvd., Fremont, CA Tel: Fax: Apacer Technology Corp. 5F, Matsura Bldg., Shiba, Minato-Ku Tokyo, , Japan Tel: Fax: Apacer Technology B.V. Science Park Eindhoven EB Son, The Netherlands Tel: Fax: #6199 Apacer Electronic (Shanghai) Co., Ltd Room D, 22/FL, No.2, Lane 600, JieyunPlaza, Tianshan RD, Shanghai, , China Tel: Fax: Apacer Technologies Pvt Ltd, Unit No.201, Brigade Corner, 7 th Block Jayanagar, Yediyur Circle, Bangalore , India Tel: Fax: sales_india@apacer.com 18