ALI-IPV3113R, ALI-IPV3130R IP Dome Camera Quick Installation Guide

Transcription

1 ALI-IPV3113R, ALI-IPV3130R IP Dome Camera Quick Installation Guide Ethernet connector - PoE capable 12 Vdc Power connector This document guides you through the basic steps to install and configure the ALI-IPV3113R and ALI-IPV3130R cameras. These cameras feature: Megapixel 1/3 in. CMOS progressive scan sensor High definition video streaming with Dual-stream video support Video stream compression: H.264 standard and MJPEG 3D-DNR noise reduction and Digital Wide Dynamic Range (WDR) Backlight compensation 65 ft IR range for night vision Dual power capable - Power over Ethernet (PoE) or 12 Vdc Weatherproof - IP66 rated and Vandalproof - IK10 rated For more information about the features of these cameras, please refer to the ALI-IP Camera Software User Manual. Camera drop cable connectors What s in the box Box contains this document with the items shown below. Drill Template Documentation and Installation Tools CD screws and wall inserts L-wrench base Weatherproof fitting for Ethernet cable Dome Assembly IR array Lens Gimbal assembly Black plastic shield Drop cable Camera module This product also includes a mounting plate adapter for attaching the camera assembly onto a junction box. Step 1. Install the camera 1. Determine the best fasteners for securing the camera to mounting surface. The mounting hardware provided is suitable for most surfaces. NOTE: A mounting plate adapter is provided for attaching the camera to a junction box. 2. Using the Drill Template provided, mark the location of the mounting screw holes. If the drop cable will be routed through the mounting surface, mark the location of the hole for the cable. NOTE: The drop cable can be routed through the cable channel on the side of the base. 3. Drill holes for the mounting fasteners, and for the drop cable if needed. 4. Remove the three lower dome screws, then separate the lower dome from the mounting base. An L-wrench is provided. 5. Route the drop cable as planned, then secure the mounting base to the surface with the fasteners. screw holes Wall inserts base screws 6. DO NOT reattach the lower dome to the mounting base at this time. Drop cable Step 2. Connect the camera to the LAN and power it on Micro SD card slot Reset button ALI-IPV3113R and ALI-3130R cameras without the dome cover Route a Ethernet LAN cable to the camera and plug it into the Ethernet connector. Seal the connection from moisture and other contamination. A weatherproof fitting is provided. If the camera is powered through the LAN cable (PoE), apply power to the cable to power on the camera, then continue to Step 3. Install the Alibi Discover Tool on page 2. ALI-IPV3113R-30R_CQ 3/6/2015

2 2. Route a 12 Vdc power cable to the camera and connect it to the 12 Vdc connector on the camera drop cable. The polarity of the drop cable connector is shown below. CAUTION Before applying power to the camera, ensure that the polarity is correct. An incorrect connection may cause a malfunction and can damage the camera. 3. Seal the power cable connectors as needed from moisture and other contamination. 4. Apply power to the cable to power on the camera. Step 3. Install the Alibi Discover Tool The Alibi Discover Tool is a software utility used to discover Alibi cameras and NVRs/DVRs installed on the LAN and change their network settings. The tool is provided on the CD with your camera. To use the tool: 1. Insert the software CD provided with your camera into an optical drive on the Microsoft Windows computer you will use to access your camera on the LAN. 2. On the CD, find the folder that contains the Alibi Discover Tool. 3. Copy the files in the folder to a new directory on your computer. The files should appear as shown in the directory shown below. b. Modify the network settings to values compatible with the subnet where it is installed. c. Enter the admin password for the device in the password field. By default, the admin user password for Alibi cameras is d. Click the Save button. The new IP address, port, etc. settings will appear in the list with the device you modified. 4. To open the Alibi Discover Tool, double click the file Alibi Discover Tool.exe. The tool will automatically discover Alibi cameras and recorders installed on the network. 6. Close the Alibi Discover Tool by clicking the Close icon ( T ) in the upper-right corner of the screen. Step 4. Remote login To access the camera from a computer on the LAN: 1. Open your Microsoft Internet Explorer browser on your compute and enter the IP address of the camera in the URL field. In the example below, the IP address of the camera is In the screen shown above, an ALI-IPV3130R camera was discovered. This camera, although installed on a subnet other than the one implied by its IP address is shown, is still found by the tool. 5. To change the network settings of the camera to be compatible with the subnet where it is installed, do the following: a. Click the device to highlight it. Notice that the network parameters are populated in the frame on the right Observint Technologies. All rights reserved.

3 a. After a successful login to the NVR, a message will appear in the middle of the Live View window requiring you to load a plug-in. Click on the message to continue, then click Run in the pop-up block at the bottom of the screen. 2. In the login window, enter your User Name and Password in the appropriate fields, then click Login. The default User Name and Password for Alibi cameras is admin and If this is the first time you are logging into a camera at this IP address AND you are using Internet Explorer 10 or newer, you must configure it for Compatibility mode: a. In Internet Explorer, click the Tools icon (located to the right of the tabs), then select Compatibility View settings from the drop-down menu. Tools icon Some computer security software may attempt to block you from running WebComponents.exe. If necessary, open the Internet Explorer downloads list, right click on the WebComponents.exe file name, then click Run Anyway. NOTE b. In the Setup - WebComponents window opens, click Next to continue. b. In the Compatibility View Settings window, ensure that the IP address of your camera is in the Add this website field, then click Add. Installing the WebComponents plugin may require that you close the browser. Follow the on-screen instructions, then restart your browser after the installation is finished. c. Allow the plug-in installation to complete. When the following window appears, click Finish. c. After clicking Add, the IP address will appear in the Websites list. Click Close. 4. If this login is the first login to an Alibi camera from your computer and browser, continue with the following sub-steps to install WebComponents: Observint Technologies. All rights reserved.

4 Step 5. Remote Live View screen After logging into the camera, the Live View - Main stream window initially appears. be opened or closed for compactness. Additionally, several adjustments can be seen in the Live View image on the menu. To open the Display Settings menu, go to Setup tab Image Display Settings Live View options Screen select tabs Live View image Logout button 1. Remove the black plastic shield that covers the camera gimbal. Capture, Record, Enable e-ptz icons 2. Observe the Live View screen to adjust the direction of the camera. To adjust the camera pan, rotate the camera gimbal (0 ~ 355 ) assemblies and as shown below. Configurable parameters include: Switch Day and Night: Select either Auto-Switch or Scheduled-Switch. If using Auto-Switch, open the Day/Night Switch submenu to select the Sensitivity, Filtering Time, and Smart IR feature ON or OFF. If using Scheduled Switch, set the Start Time and End Time of the switch, then open the Day/Night Switch submenu to select the Smart IR feature ON or OFF. Also, click the Common, Day and Night tabs to set the Saturation, Hue, Brightness, Contrast and Sharpness for Day and for Night modes. Grasp here on both sides Grasp here on both sides Pan adjustment 3. To adjust the horizon line (0 ~ 360 ) and tilt (0 ~ 65 ), rotate the camera module as shown below. Horizon line adjustment 4. Re-install the black plastic shield. 5. Reattach the lower dome. Step 6. Adjust the video display Tilt adjustment The video Display Settings menu includes the image-related configurable parameters for the camera. It contains several sub-menus such as Image Adjustment, Exposure Settings, Day/Night Switch, etc. that can Image Adjustment submenu: Open the Image adjustment submenu to set the Saturation, Hue, Brightness, Contrast and Sharpness of the video image. Each parameter can be set to a level of 0 ~ 100 either by moving the slider or entering the value in the box on the right. The effect of the adjustment will appear in the Live View image in the menu. Exposure Settings submenu: In this submenu, set the following for the best performance: Iris Mode: Select Auto or Manual. Some cameras may not offer both options. Exposure Time: Value ranges from 1/3 to 1/100,000 s. The nominal value is 1/150. Adjust it according to the lightening condition. Gain: Set the gain to show the optimal brightness level. Day/Night Switch submenu: You can set the Day/Night switch to Day, Night, Auto, or Schedule. The option you select determines the submenu options. Day or Night: These options both have one parameter: Smart IR. Auto: If you select Auto switch, you can set the sensitivity (0.. 7), filtering time and Smart IR. Schedule: Use Schedule to set that Start Time and End Time for the switch. Smart IR is also selectable. Backlight Settings: Backlight settings include BLC Area (Off, Up, Down Left Right Center), the area to control, and WDR (Wide Dynamic Range) ON or OFF. White Balance: White Balance selection is used to correct colors in the image depending on the lighting source. You can also set the white balance manually (MWB), using Automatic White Balance (AWB1), and lock the white balance setting (Locked WB). Image Enhancement: Options in this submenu include Digital Noise Reduction (DNR) ON or OFF. If ON, yo can also adjust the level of noise reduction. Video Adjustment: Video Adjustment includes: Observint Technologies. All rights reserved.

5 Mirror: Mirror adjustment enables you to flip the image (Up/Down), flip Left/Right (reflect or Center). Rotate: Rotate rotates the image +90 degrees. Rotate and Mirror can be used to adjust the image in any orientation. Video Standard: Select 60 Hz for NTSC format. Capture Mode: To make a complete use of the 16:9 aspect ratio, you can enable the capture mode when you use the camera in a narrow view scene. Specifications Model ALI-IPV3113R ALI-IPV3130R Image Sensor Scanning Mode 1/3 CMOS Progressive Scan Resolution Up to 1280 x 960 Up to 2048 x 1536 Effective Pixels Approx. 1.3 Megapixel Approx. 3.0 Megapixel Minimum Illumination Day/Night Electronic Shutter (sec) Wide Dynamic Range Gain Control White Balance Mode Noise Reduction IR Illuminators IR Array Range IR Sensitivity Color: lux (F2.0, AGC On) B/W: 0 lux (IR ON) True Day/Night ICR 1/3 ~ 1/100,000 (Auto/Manual) Digital WDR Auto Auto 3D DNR Smart IR Array, 850 nm 65 ft nm Panning Range 0 ~ 355 Tilting Range 0 ~ 65 Rotation 0 ~ 360 Color: 0.07 lux (F2.0, AGC On) B/W: 0 lux (IR ON) Lens Lens Type Fixed Focal Length 4 mm Iris Fixed Focus Manual Horizontal Viewing Angle F-number F2.0 Video Video Compression Format H.264 (Main Profile), MJPEG CODEC Streaming Capability Dual Streaming Maximum Frame Rate x x 1536, p Bit Rate 32 kbps ~ 16 Mbps Bit Rate Mode CBR, VBR Feature Motion Detection Backlight Compensation Event Notification Alarm Output, , FTP Privacy Mask Video Analytics Tamper Detection, Line Crossing, Intrusion Detection Interface Ethernet RJ-45 10/100BASE-T SD Card Slot 1x Micro SD/SDHC/SDXC (up to 64GB) Network Protocols TCP/IP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTP, RTSP, RTCP, PPPoE, NTP, UPnP, SMTP, SNMP, IGMP, 802.1X, QoS, IPv6, Bonjour, ONVIF, PSIA Security Password Protection, IP address filtering Number of Connections Up to 10 Model ALI-IPV3113R ALI-IPV3130R General Power Requirements PoE (IEEE802.3af) / 12 Vdc Power Consumption 7 W max (IR ON) Weight 1.35 bs Dimensions 2.1 H x 3.91 L x 3.81 operating Temperature -22 F ~ 140 F Operating Humidity 0% ~ 95% RH, Non-condensing Ingress Protection IP66 Impact Protection IK10 Color White Material Aluminum (body) / Polycarbonate (Bubble) Approvals CE, FCC, RoHS System Requirements Operating System Microsoft Windows XP Professional, Windows VISTA, Windows 7, Window 8 Processor Intel Pentium GHz or later Memory 1 GB or above RAM Display 1024 x 768 resolution or higher Web Browser Microsoft Internet Explorer 6.0 or above, Apple Safari 5.02 or above, Mozilla Firefox 3.5 or above, Google Chrome 8 or above Supplied Accessories CD ROM (User s Guide, Installation Tools) Quickstart Guide Hardware and Template Junction box adaptor plate Observint Technologies. All rights reserved..