INSTALLATION INSTRUCTIONS
|
|
- Anna Strickland
- 7 years ago
- Views:
Transcription
1 INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08E10-SNA CIVIC 2- AND 4-DOOR All Issue Date AUG 2010 NOTE: The interior illumination lights cannot be installed on 2-door vehicles equipped with fog lights or with VSA. 3 Screws PARTS LIST Interior illumination light (with blue tape) 3 Flange nuts 2 Interior illumination lights (with white tape) Switch Interior illumination light harness Template Bracket Fuse label Wire tie with clip 10 Wire ties EPT sealer Switch trim 2 Switch lids 2010 American Honda Motor Co., Inc. - All Rights Reserved. AII (1008) 08E10-SNA of 13
2 Illustration of the Interior Illumination Lights Installed on the Vehicle FUSE CASE (2A) 3. If equipped, remove the driver s dashboard under cover (turn the knob counterclockwise, and release two clips and pin). PIN TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Ratchet 10 mm Socket Drill Drill bits (3 mm, 5 mm, and 10 mm) File Pushpin Utility knife Scissors Piece of steel wire Electrical tape Adhesive tape Eye protection (face shield, safety goggles, etc.) Scale Shop towel INSTALLATION (With white tape.) (With white tape.) T (With blue tape.) Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 2 CLIPS 4. Remove the driver s dashboard lower cover (eight clips). LOWER COVER T 8 CLIPS T KNOB 1. Make sure you have the anti-theft code for the radio, then write down the radio station presets. 2. Disconnect the negative cable from the battery. 2 of 13 AII (1008) 2010 American Honda Motor Co., Inc. - All Rights Reserved.
3 5. Lower the tilt lever, and move the steering wheel to its lowest position. After moving the steering wheel, return the tilt lever to its original position. 8. Shift to S or 2, and remove the lid from the dashboard center lower cover (four retaining tabs). SHOP TOWEL COMBINATION WIPER/ WASHER SHIFT LEVER ( S or 2 position) CENTER LOWER COVER SHOP TOWEL STEERING WHEEL SHIFT LEVER TILT LEVER 4 RETAINING TABS LID T T 9. Remove the passenger s dashboard under cover (four clips and two pins). 6. Cover the combination light switch, wiper/washer switch, and shift lever with shop towels to protect them from damage. 7. Apply masking tape to the dashboard. Remove the instrument panel (one self-tapping screw and 11 clips), and unplug the vehicle connector. INSTRUMENT PANEL MASKING TAPE 2 PINS PASSENGER S T 4 CLIPS VEHICLE SELF- TAPPING 11 CLIPS B 2010 American Honda Motor Co., Inc. - All Rights Reserved. AII (1008) 3 of 13
4 10. Remove the two bolts. Open the glove box, push inward on the stops, and remove the glove box. 13. Plug the interior illumination light harness 6-pin connector into the fuse box 6-pin connector. STOP 6-PIN CONNECTING PORT FUSE BOX GLOVE BOX BOLT T Routing the Interior Illumination Light Harness 11. Route the interior illumination light harness 5-pin connector behind the fuse box, and pull it out through the opening of the air duct. 5-PIN BRANCH OF 100 mm 6-PIN NOTE: If another accessory is already plugged into the 6-pin connector, remove the dummy connector from the other accessory harness, and plug the interior illumination light harness into that connector. OTHER ACCESSORY 6-PIN T FUSE BOX OPENING OF AIR DUCT DUMMY (Discard.) BRANCH OF VEHICLE FUSE BOX 6-PIN T 6-PIN T 12. Measure the vehicle harness from the point of the branch as shown. Secure the interior illumination light harness (6-pin connector side) to the vehicle harness with one wire tie. 4 of 13 AII (1008) 2010 American Honda Motor Co., Inc. - All Rights Reserved.
5 14. Route the two interior illumination light harness 2-pin connectors to the right side of the vehicle along the vehicle harness. 2-PIN FUSE LABEL S ( 2A) 17. Route a steel wire through the opening for the lid of the dashboard center lower cover, and wind it onto the interior illumination light harness 2-pin connector (long harness side). ELECTRICAL TAPE STEEL WIRE FUSE CASE FRONT GROUND BOLT (Reuse.) ELECTRICAL TAPE GROUND TERMINAL T 2-PIN T 15. Attach the 2A fuse label to the interior illumination light harness fuse case. 16. Remove the ground bolt from the vehicle. Secure the interior illumination light harness ground terminal with the ground bolt you just removed. 18. Secure the other 2-pin connector to the interior illumination light harness with electrical tape. 19. Pull the interior illumination light harness out of the lid opening of the dashboard center lower cover. STEEL WIRE ELECTRICAL TAPE T 20. Remove the wire and electrical tape from the interior illumination light harness American Honda Motor Co., Inc. - All Rights Reserved. AII (1008) 5 of 13
6 21. Route the interior illumination light harness 2-pin connector to the passenger s side along the vehicle harness. 23. Secure the interior illumination light harness to the vehicle harness with three wire ties. OPENING IN GLOVE BOX VEHICLE T 22. Secure the interior illumination light harness to the vehicle harness with two wire ties. VEHICLE 2-PIN T 24. Secure the interior illumination light harness to the vehicle harness using four wire ties if the vehicle is equipped with the driver s dashboard under cover. Use three wire ties if the vehicle does not have a driver s dashboard under cover. FUSE BOX T VEHICLE (Vehicle with driver s dashboard under cover only) WIRE TIE T 6 of 13 AII (1008) 2010 American Honda Motor Co., Inc. - All Rights Reserved.
7 Installing the Interior Illumination Lights 25. Using scissors, cut out the template. 28. Using a pushpin, pierce the template at the three marked points. Remove the template. CURVED END PUSHPIN TEMPLATE (A) TEMPLATE T If the vehicle is equipped with a driver s dashboard under cover, go to step 26; otherwise, go to step Pull up the insulator on the driver s dashboard under cover, and cut into it as shown. 27. Secure template (A) to the driver s dashboard under cover with tape by aligning it with the square hole at the end of the curve as shown. HOLE T 60 mm 29. While wearing eye protection, drill one 10 mm hole and two 5 mm holes at the pierced points in the driver s dashboard under cover. First drill with a 3 mm bit, then finish with a 5 mm bit/10 mm bit as shown. Using a file, remove any burrs from the holes. DRILL (3 mm 5 mm drill bit) INSULATOR T DRILL (3 mm 10 mm drill bit) T 2010 American Honda Motor Co., Inc. - All Rights Reserved. AII (1008) 7 of 13
8 30. Cut the rib on the driver s dashboard under cover as shown. Using a file, remove any burrs from the edge. 32. Bundle the interior light harness and secure the connector to the bracket using a wire tie with clip. WITH CLIP RIB BRACKET T 31. Route one interior illumination light (with white tape) connector through the 10 mm hole. Install the interior light and bracket on the driver s dashboard under cover with a screw and flange nut. FLANGE NUT T 33. Reinstall the insulator to the driver s dashboard under cover, and pass the interior illumination light connector through the slit. INSULATOR BRACKET T UNDER COVER SLIT (with white tape) T 8 of 13 AII (1008) 2010 American Honda Motor Co., Inc. - All Rights Reserved.
9 34. Position template (B) on the lid of the dashboard center lower cover. LID OF CENTER LOWER COVER PUSHPIN TEMPLATE (B) 37. Route the interior illumination light (with blue tape) connector through the 10 mm hole. Install the courtesy light on the lid with a screw and flange nut. FLANGE NUT LID EPT SEALER (1/3) (with blue tape) T T 35. Using a pushpin, pierce the template at the three marked points. Remove the template. 36. While wearing eye protection, drill one 10 mm hole and two 5 mm holes at the pierced points on the lid. First drill with a 3 mm bit, then finish with a 5 mm bit/10 mm bit as shown. Using a file, remove any burrs from the holes. 38. Using scissors, cut one EPT sealer into three equal pieces. Wrap one of the pieces around the interior illumination light connector. 39. Secure template (C) to the passenger s dashboard under cover with tape by aligning it with the square hole and the end of the curve as shown. Do not use the marks on the inside of the passenger s dashboard under cover. DRILL (3 mm 5 mm drill bit) DRILL (3 mm 10 mm drill bit) PUSHPIN CURVED END HOLE LID PASSENGER S TEMPLATE (C) T T 40. Using a pushpin, pierce the template at the three marked points. Remove the template American Honda Motor Co., Inc. - All Rights Reserved. AII (1008) 9 of 13
10 41. While wearing eye protection, drill one 10 mm hole and two 5 mm holes at the pierced points on the passenger s dashboard under cover. First drill with a 3 mm bit, then finish with a 5 mm bit/10 mm bit as shown. Using a file, remove any burrs from the holes. Do not use the marks on the inside of the passenger s dashboard under cover. DRILL (3 mm 5 mm drill bit) DRILL (3 mm 10 mm drill bit) PASSENGER S If the vehicle is not equipped with a driver s dashboard under cover, continue with steps 44 to 47; otherwise, go to step Assemble the interior illumination light (with white tape) to the bracket using a screw and flange nut. VEHICLE BRACKET FLANGE NUT (with white tape) T 42. Route the interior illumination light (with white tape) connector through the 10 mm hole. Install the interior illumination light on the passenger s dashboard under cover with a screw and flange nut. FUSE BOX EPT SEALER (1/3) BRACKET SELF-TAPPING T (reused) 45. Remove the self-tapping screw from the vehicle bracket. Secure the bracket to the vehicle bracket using the self-tapping screw that you just removed. FLANGE NUT PASSENGER S 46. Wrap the remaining piece of EPT sealer that you cut into three equal pieces around the interior illumination light connector. EPT SEALER (1/3) 47. Plug the interior illumination light connector into the interior illumination light harness 2-pin connector, and secure them to the interior illumination light harness using a wire tie. (with white tape) T 43. Wrap another piece of the EPT sealer that you cut into three equal pieces around the interior illumination light connector. 2-PIN T 10 of 13 AII (1008) 2010 American Honda Motor Co., Inc. - All Rights Reserved.
11 If the vehicle is equipped with an instrument panel pocket, continue with step 48; otherwise, go to step Remove the pocket from the instrument panel (three self-tapping screws). 51. Remove the switch lid from the instrument panel. INSTRUMENT PANEL SELF- TAPPING INSTRUMENT PANEL POCKET (Discard.) T LID (Discard.) 52. Install the switch in the instrument panel T 53. Plug the interior illumination light harness 5-pin connector to the switch, and reinstall the instrument panel. 49. Install the switch trim to the instrument panel with the three self-tapping screws. SELF- TAPPING (reused) TRIM INSTRUMENT PANEL LID T INSTRUMENT PANEL T 5-PIN 54. Reinstall the driver s dashboard lower cover and glove box. 50. Install the switch and two switch lids to the switch trim. Go to step American Honda Motor Co., Inc. - All Rights Reserved. AII (1008) 11 of 13
12 55. If equipped with a driver s dashboard under cover, plug the interior illumination light harness 2-pin connector to the interior illumination light connector on the driver s dashboard under cover, and reinstall the under cover. 57. Plug the interior illumination light harness 2-pin connector to the interior illumination light connector on the passenger s dashboard under cover, and reinstall the under cover. 2-PIN 2-PIN T PASSENGER S T 56. Plug the interior illumination light harness 2-pin connector to the interior illumination light connector on the lid of the dashboard center lower cover, and reinstall the lid. 2-PIN CENTER LOWER COVER LID T 12 of 13 AII (1008) 2010 American Honda Motor Co., Inc. - All Rights Reserved.
13 58. Check that all wire harnesses are routed properly and all connectors are plugged in. 59. Reinstall all removed parts. Check that all clips and other fasteners are installed securely. 60. Reconnect the negative cable to the battery. 61. Enter the customer s radio anti-theft code, and reset the radio station presets. 62. Reset the clock. HOW TO OPERATE Turn the headlight switch to the and position (headlights on low beam). Press the courtesy light switch. NOTE: When the battery is disconnected, the driver s window auto up/down function is disabled. Start the engine. Push down on the driver s window switch until the window is fully open. Pull up on the driver s window switch to close the window completely, then hold the switch for two seconds or more. Lower and raise the driver s window to check the operation of the driver s window auto up/down function. COURTESY HEAD OFF ON - ON ON OFF T 2010 American Honda Motor Co., Inc. - All Rights Reserved. AII (1008) 13 of 13
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. ACCORD All 30209 2-AND 4-DOOR SYSTEM (VP, LX, SE) Issue Date AUG 2005 PARTS LIST Security System Attachment: P/N 08E55-SDA-100A Unit panel
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 26327 2004 S2000 Issue Date OCT 2004 PARTS LIST Security System: P/N 08E51-S84-100 Attachment Kit: P/N 08E55-S2A-101 2 Remote controls
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII23628 2003 PILOT Issue Date MAY 2002 PARTS LIST Security System Kit (sold separately): P/N 08E51-S84-100 2 Remote controls Attachment
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 24393 ACCORD (DX, LX) SYSTEM 2-AND 4-DOOR Issue Date AUG 2002 PARTS LIST Security System Attachment (LX): P/N 08E55-SDA-100A Unit panel
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. XM RADIO SYSTEM 2003 ACCORD 4 DOOR AII 24378 Issue Date MARCH 2003 The XM Radio will not fit in a vehicle equipped with a rear entertainment
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory TRIM Application 2008 ACCORD 4-DOOR Publications No. AII 35362 Issue Date AUG 2007 PARTS LIST Steering Wheel Trim (Without Navigation) P/N 08Z13-TA0-100 Right steering
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application 2009 PILOT Publications No. AII 39408 Issue Date MAY 2008 PARTS LIST Steering Wheel Trim (With Cruise and Audio) P/N 08Z13-SZA-130B (Chocolate) P/N 08Z13-SZA-140B
More informationTOYOTA TACOMA 2008- HANDS FREE BLU LOGIC Preparation
TOYOTA TACOMA 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00112 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationTrailblazer, Envoy, Rainier, Ascender
6. After removing the trim plate bezel simply remove the four ¼ screws holding the instrument cluster in place. Pull the cluster out and unplug the single wiring harness connection in the back. Trailblazer,
More informationTOYOTA PRIUS 2010- HANDS FREE BLU LOGIC Preparation
TOYOTA PRIUS 2010- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: Illuminated Kick Plate APPLICATION: Rogue (2011) PART NUMBER: 999G6 GX010 KIT CONTENTS: Item A B C G H QTY 1 1 1 D 1 E 1 F 3 15 6 Description Kick Plate,
More informationInstallation Instructions
Installation Instructions For Use with PXPV230, PXPV265, PXPD230, and PXPD265 models Attention! - Please read these instructions completely before attempting installation. Always unplug the power supply
More information5 Mechanisms and accessories
5 Mechanisms and accessories 51A SIDE OPENING ELEMENT MECHANISMS 52A NON-SIDE OPENING ELEMENT MECHANISMS 54A WINDOWS 55A EXTERIOR PROTECTION 56A EXTERIOR EQUIPMENT 57A INTERIOR EQUIPMENT X79 NOVEMBER 2009
More informationInstallation instruction do88 Intercooler for Volvo S40 / V50 / C30
Installation instruction do88 Intercooler for Volvo S40 / V50 / C30 This instruction shows how to replace the OEM intercooler with our performance intercooler. 2. 3. 1. 4. 5. Part number: ICM-170 6. At
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
REMOVAL/INSTALL OF WINDOW REGULATOR (741-306) Honda Accord 2003 07 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue. A plastic
More informationINSTALLATION MANUAL INSIDE PASSENGER COMPARTMENT. HFC 134a FOR EUROPEAN SPEC. / GENERAL SPEC. AIR CONDITIONING ENGLISH
HFC 134a Ozone Friendly Refrigerant FOR EUROPEAN SPEC. / GENERAL SPEC. AIR CONDITIONING ENGLISH AAAMU-60 / INSIDE PASSENGER COMPARTMENT INSTALLATION MANUAL 2000 (EUROPE) B.V.. All Rights Reserved. This
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. DESCRIPTION: Auto-Dimming Mirror Kit with Compass and HomeLink 2. APPLICATION: Titan 3. PART NUMBER: 999L1 WS000 4. KIT CONTENTS: Item Qty Description Service
More informationInstallation Instructions
Installation Instructions Page 1 of 16 January 2008 Equipment Parts, Trailer Hitch Ver 3.0 Accessory Development SUBJECT TRAILER HITCH KIT (US Only) - P/N 71 60 0 413 359 MODEL X5 (E70): Select Vehicle
More informationTOOL SVC NUMBERS: 250-2598, 250-2600 SVC CONTENTS ITEM QTY DESCRIPTION PART NUMBER 1 1 CUTTING TOOL 250-2598 2 1 EXTRACTION TOOL/PART# 250-2600
07-08 TOYOTA FJ CRUISER, 05-09 SIENNA, 06-08 SCION TC PART NUMBER: 250-1732 1 CRUISE CONTROL KIT TOOL SVC NUMBERS: 250-2598, 250-2600 2 2 1 BASE KIT CONTENTS ITEM QTY DESCRIPTION 1 1 CONTROL SWITCH ASSEMBLY
More informationTOYOTA Tundra 2007 - BACK-UP CAMERA SYSTEM Preparation
Preparation Part Number(s): PT233-34070, PT923-35070-11, PT923-35070-43 NOTE: Part number of this accessory may not be the same as part number shown. Back Up Monitor Kit Contents PT923-35070-11 / PT923-35070-43
More informationKEYLESS ENTRY UPGRADE SECURITY SYSTEM for 2004 TOYOTA HIGHLANDER
KEYLESS ENTRY UPGRADE SECURITY SYSTEM for 2004 TOYOTA HIGHLANDER DEALER SERVICE AND INSTALLATION MANUAL KIT NO. 00016-30915 Contents PARTS LIST... 2 PARTS ILLUSTRATIONS... 2 VEHICLE PREPARATION... 3 INSTALLING
More informationInstalling RNS-E SAT NAV for Audi A4
As one of the major options on the A4 you can get a DVD Satellite Navigation System call the RNS-E. With the help of ebay these sat nav systems are now available to by at a rough cost of 650 plus the cost
More informationTime needed: ~3h for lid replacement only. Add 1h for operation harness in lid and ~2h more for installing drive unit and cable harness in trunk.
DIY for replacing trunk lid and/or retrofitting electrical operation of trunk lid. This document is meant to be a support and give advice on the procedure but I will take no responsibility for any damage
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW LIFT MOTOR
REMOVAL/INSTALL OF WINDOW LIFT MOTOR (742-273) Ford Expedition 1997 2002, Lincoln Navigator 1998 2002, Ford F-150 Super Crew Cab 2001 General Tech Tips: Use painter s tape rather than duct tape to secure
More informationBefore installation it is important to know what parts you have and what the capabilities of these parts are.
INSTALLATION GUIDE Before installation it is important to know what parts you have and what the capabilities of these parts are. The Recon XZT is the smallest and most powerful gauge of its kind. With
More informationRetrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006
Retrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006 Disclaimer: This set of instructions is simply a guide on how I installed my own heated steering
More informationInstrument panel. Volkswagen Touareg - Instrument panel. Special tools, testers and auxiliary items required. Release lever T10039
Volkswagen Touareg - Instrument panel Page 1 / 14 70-1 Instrument panel Tools Special tools, testers and auxiliary items required Release lever T10039 Instrument panel, removing and installing Removing
More information2003/2004/2005 TOYOTA COROLLA
2003/2004/2005 TOYOTA COROLLA KEYLESS ENTRY UPGRADE SECURITY SYSTEM INSTALLATION INSTRUCTIONS KIT NO. 00016-30120 SPECIAL NOTE: Installation Sequences After TMS and Safety mandated preparatory steps have
More informationTOYOTA TUNDRA 2015 Billet Grille w/led DRL
TOYOTA TUNDRA 2015 Billet Grille w/led DRL Part Number: 00016-34088 Accessory Code: BG3000 Conflicts Models 1794 and Platinum Kit Contents Item # Quantity Reqd. Description 1 2 LED DRL 2 1 Driver Box 3
More informationCONTENTS TOOLS REQUIRED: Ratchet 13mm Socket 10mm Socket Phillips Screwdriver Pliers Panel Removal Tool. Amp Installation
CONTENTS 1EA. SUBWOOFER ASSEMBLY P/N RUWRANGLER 1EA. 200 WATT AMP/BRACKET ASSEMBLY P/N RM11JKBTL - Bracket P/N RE08BTL200R - Amp 1EA. POWER HARNESS P/N RHWRANGLERPWR 1EA. OVERLAY HARNESS P/N RHWRANGLER
More informationspecializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1967-72 CHEVROLET PICKUP
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1967-72 CHEVROLET PICKUP CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect
More informationInstallation instructions, accessories - Navigation system, RTI
XC90 Section Group Weight(Kg/Pounds) Year Month 3 393 4/8.8 2007 08 Page 1 of 20 Required tools A0000162 IMG-239667 IMG-239664 IMG-239980 IMG-242205 R8802817 R3905015 Page 2 of 20 R3903812 IMG-213320 Page
More informationWARNING! REQUIRED TOOLS & SUPPLIES: HIGH VOLTAGE
INSTRUCTIONS Product: GEM Electric Motorcars Models: All Subject: Instructions for installing Stereo Accessory Estimated Completion Time:.75 Hours Parts: See Page # 7 REQUIRED TOOLS & SUPPLIES: (1) 3/8
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
REMOVAL/INSTALL OF WINDOW REGULATOR (748-547) Chrysler 300 2005 10, Dodge Magnum 2005 08, Dodge Charger 2006 09 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not
More informationGPS AutoSteer System Installation Manual
GPS AutoSteer System Installation Manual Supported Vehicles John Deere Sprayers 4720 4630 4730 4830 AutoTrac Ready PN: 602-0227-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions in this manual
More informationInstallation instructions, accessories - Handsfree for cellular phone, system B, entry level
XC90 Section Group Weight(Kg/Pounds) Year Month 3 39 0.5/1.1 2006 07 XC90 2003, XC90 2004 IMG-249663 Page 1 of 18 Required tools A0000162 A0000163 IMG-239664 M0000232 IMG-253123 IMG-252223 Page 2 of 18
More informationParts Required: Remove the Falcon Wiper Motor:
INTERMITTENT WINDSHIELD WIPERS + 2 SPEEDS By Dick Harrington If you frequently drive your Falcon or Comet, sooner or later you will get caught in the rain. The first item of defense for good vision is
More informationSolstice/Sky Water Pump Replacement
Solstice/Sky Water Pump Replacement The water pump on the Solstice/Sky is starting to need replacement on some vehicles. This guide will help in replacing the water pump while the engine is still in the
More informationFRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER
Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER Please read before beginning Stainless steel hardware
More informationGuide for Modified Assembly: Lightning McQueen. By: Collin Patterson, University of Delaware. Materials and Tools:
Guide for Modified Assembly: Lightning McQueen By: Collin Patterson, University of Delaware Materials and Tools: PVC o 40 inches of 1 in diameter PVC o 25 inches of ¾ in PVC o 4 x 1 in elbows o 2 x ¾ in
More informationPOWER LOCK KIT GENERAL INSTALLATION -J04427 REV. 2007-12-04. Kit Number. Models. Additional Parts Required. Kit Contents
-J0 REV. 00--0 POWER LOCK KIT GENERAL Kit Number -0, 0-0 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section of www.harleydavidson.com (English
More informationP150SC15. Designed for 2015 Ford F150 Super-Cab and Super-Crew vehicles without Sony System. 2015 Stillwater Designs P150SC15-A2-20150813
P150SC15 Designed for 2015 Ford F150 Super-Cab and Super-Crew vehicles without Sony System Subwoofer Assembly Amplifier Assembly Amplifier Harness 2015 Stillwater Designs P150SC15-A2-20150813 M6 Bolt M6
More informationUNIVERSAL LUMBAR INSTALLATION INSTRUCTIONS
UNIVERSAL LUMBAR INSTALLATION INSTRUCTIONS CONTENTS Parts List... 2 Parts Diagram... 2 Helpful Hints... 3 Installation... 4 Operation and Troubleshooting Guide... 6 Warranty Information... 8 Form #3132,
More informationPost Mount Light Installation*
Post Mount Light Installation* *For the general installation of most Post Mount Spotlights, many vehicles may need slight modifications to these instructions. You will need the following tools: High torque
More informationNetworkfleet 3500 Product Line Installation Guide
Networkfleet 3500 Product Line Installation Guide Light/Medium Duty (L3500) Heavy Duty (H3500) Universal (U3500) www.networkcar.com/fleet Customer Care: (866) 227-7323 customercare@networkcar.com Table
More information741-760 INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
REMOVAL/INSTALL OF WINDOW REGULATOR (741-760) Chevy Cavalier, Pontiac Sunfire Coupe 1996 2005 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
REMOVAL/INSTALL OF WINDOW REGULATOR (741-644) Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, GMC Yukon, Chevrolet Silverado, GMC Sierra 2000 05 General Tech Tips: Use painter s tape rather than
More informationVolkswagen Jetta, Golf, GTI 1999, 2000 Brake System 46 Brakes - Mechanical Components (Page GR-46)
46 Brakes - Mechanical Components (Page GR-46) Front brakes Brake pads, removing and installing Brake pads, removing and installing FN 3 brake caliper, servicing FS III brake caliper, servicing Rear wheel
More informationStep 1. Item 6. Item 1
Voltage Regulators QD3/T350 Motor Replacement Kit Kit Number 57A63675100B Service Information S225-50-35 Contents General..................................... 1 Parts Supplied...............................
More informationINSTALLATION INSTRUCTIONS FOR 2006-2009 VW MK5
CI100018 INSTALLATION INSTRUCTIONS FOR 2006-2009 VW MK5 Rabbit, Jetta 2.5L These instructions are applicable to vehicles equipped with either manual or automatic transmissions Thank you for choosing to
More informationVW Jetta, Golf, New Beetle 1.9L TDi Unichip PnP Installation Instructions
VW Jetta, Golf, New Beetle 1.9L TDi Unichip PnP Installation Instructions and Warranty Information Tools Required 10mm combination wrench, 13mm Socket (Jetta/Golf only), 3/8-inch or ¼-Inch drive ratchet,
More informationEZ-Steer Assisted Steering System
EZ-Steer Assisted Steering System Installation Instructions Platform Kit P/N 53059-54 Case IH CVX 1135 CVX 1145 CVX 1155 CVX 1170 CVX 1190 CVX 1195 CVX 135 CVX 145 CVX 155 CVX 175 CVX 195 New Holland TVT
More informationConvertible Top Hydraulic Cylinder Removal Manual for W124 E-Class Convertibles 1993-1995 Models 300CE (1993) and E320 (1994-1995)
Convertible Top Hydraulic Cylinder Removal Manual for W124 E-Class Convertibles 1993-1995 Models 300CE (1993) and E320 (1994-1995) Written by Samit Ghosh with picture material from vexed of benzworld.org
More informationC5 Sound Deadening & Insulation Kit Interior Removal & Installation Instructions
C5 Sound Deadening & Insulation Kit Interior Removal & Installation Instructions Ok, let's start with taking the radio bezel dash area off first. Here is what the OEM radio looks like... First you flip
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Application Outboards Faria 5 Gauge Set* Publication No. Description Part Number Honda Code PII53606A White faced, flat lens 06300-ZW5-010ZB 6315410 Issue Date Black faced, flat
More informationPERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1967 CHEVROLET IMPALA
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1967 CHEVROLET IMPALA CONTROL & OPERATING INSTRUCTIONS The controls on your new
More informationA&A CORVETTE PERFORMANCE C6 BOOST & FUEL GAUGE INSTALLATION INSTRUCTIONS
A&A CORVETTE PERFORMANCE C6 BOOST & FUEL GAUGE INSTALLATION INSTRUCTIONS 1. Check your gauges before you take them out of the packaging to make sure they are at 0 (zero) psi for both boost and fuel pressure.
More informationWiper Motor Marinco 2.5. Installation Instructions
Wiper Motor Marinco 2.5 Installation Instructions Wiper Motor Marinco-2.5 The Marinco 2.5 Wiper Motor Offers the Following Features: Fully sealed base and housing which allows installation in outdoor wet
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Handle Camera Mirror Display 2004-2014 Ford F-150 and 2008-2015 Ford Super Duty (Kit part numbers 9002-9521) Kit Contents: Mirror Tailgate Handle with camera and harness Interior
More informationPart Number: 250-1859
General Applicability 2010 Honda Insight 07- Kia Optima / Forte / Rondo/ 10- Sedona / 12 Soul 10- Hyundai Tucson / Elantra Touring ETC 2012 Accent / Elantra/ Genesis Recommended Tools Safety Tools Gloves,
More informationCOMPONENTS IP 2 INSTRUMENT PANEL INSTRUMENT PANEL ASSEMBLY ASSIST GRIP RETAINER RH FRONT PILLAR GARNISH RH FRONT DOOR OPENING TRIM WEATHERSTRIP RH
INSTRUMENT PANEL INSTRUMENT PANEL INSTRUMENT PANEL PRECAUTION 1 1. PRECAUTION FOR VEHICLE WITH SRS AIRBAG AND SEAT BELT PRETENSIONER (a) Some of these operations may affect the SRS airbag system. Read
More informationhttp://mbworld.org/forums/c32-amg-c55-amg-w203/449471-famous-ac-clicking-noiseac-footwell-damper-linkage-replacement-diy-details-steps.
Air Conditioner / HVAC W203 Stepper Motor Repair PART 2 OF 3 forums/c-class-w203/177068-noisy-air-conditioner-stepper-motorreplacement-clicking-hissing.html forums/c32-amg-c55-amg-w203/449471-famous-ac-clicking-noiseac-footwell-damper-linkage-replacement-diy-details-steps.html
More informationLIFT-505. BMF Lift Kit. Yamaha Drive Gas or Electric. Installation Instructions
LIFT-505 BMF Lift Kit Yamaha Drive Gas or Electric Installation Instructions Contents of LIFT-505 Yamaha Drive BMF Lift Kit: a (1 ea.) BMF A-Arm Assembly b (1 ea.) Driver Side Shock Tower c (1 ea.) Passenger
More informationBUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS
BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS PLEASE READ COMPLETE INSTRUCTIONS BEFORE YOU BEGIN LEAVE INSTALLATION INSTRUCTIONS AND USER'S GUIDE WITH OWNER ALL ELECTRIC WIRING AND PLUMBING MUST BE DONE
More informationCOOPER S PULLEY UPGRADE KIT INSTALLATION INSTRUCTIONS PART NUMBER NME5011
COOPER S PULLEY UPGRADE KIT INSTALLATION INSTRUCTIONS PART NUMBER NME5011 Below are instructions for the Mini Mania Pulley Upgrade Kit, Part Number NME5011. Please take all necessary precautions for working
More informationBoxster. Technical Information. Service 3/99 9415. Litronic Retrofit Kit
Litronic Retrofit Kit 9 3/99 9415 Binder - 9, Electrics This bulletin replaces bulletin Grp. 9, #3/99, dated 5-20-99. Vehicle Type: Model Year: Concern: Information: As of 1997 (V) Retrofitting Litronic
More informationAll-Season Sunroom Sliding Glass Door Installation Instructions
ASRESGD-08 All-Season Sunroom Sliding Glass Door Installation Instructions Panel Frame Door Frame Left Side Foam Insulator IE241 H Bar Assembly Door Frame Top Track Panel Frame Door Frame Right Side Stationary
More informationBACKUP CAMERA JEEP COMMANDER/GRAND CHEROKEE
BACKUP CAMERA 1 JEEP COMMANDER/GRAND CHEROKEE 2 Call Out Description Parts Quantity 1 Tie Wrap-Nylon 6.9" Supplied in kit 12 2 Camera, Rear View Supplied in kit 1 3 Camera Extension Harness Connector Supplied
More information2003 ACCORD - Automatic Transmission Removal
2003 ACCORD - Automatic Transmission Removal Special Tools Required Engine support hanger, A and Reds AAR-T-12566 Engine hanger balancer bar VSB02C000019 Front subframe adapter VSB02C000016 These special
More informationMulti Function, User Configurable Remote Vehicle Security System with 4 Button Replaceable Membrane Remote Transmitter
MODEL PRO-9744 INSTALLATION MANUAL Multi Function, User Configurable Remote Vehicle Security System with 4 Button Replaceable Membrane Remote Transmitter This System Allows The Transmitter Buttons To Be
More informationEZ-Steer Assisted Steering System
EZ-Steer Assisted Steering System Installation Instructions Platform Kit P/N 53059-21 Case IH Puma 165 Puma 180 Puma 195 Puma 210 New Holland T7030 T7040 T7050 T7060 Revision A June 2007 Part Number 53345-21-EU2
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Aftermarket and Factory 5.0, 8.4 and 6.1 MyGig Touch Screen Display (Factory Display requires Chrysler/Dodge dealer to activate) 2009 Current* Dodge Ram (Kit part number 1009-6503) *NOTE:
More informationBack-Up Camera Installation Guide
Hz Hz In This Guide: Back-up camera installation requires connecting power wiring to the existing reverse lighting circuit and adding a chassis ground, as well as routing a video signal cable to the front
More informationFront brakes (FN- 3), servicing
j a t Front brakes (FN- 3), servicing 46-1 Front brakes, servicing Note: Install complete repair kit. After replacing brake pads and before moving vehicle, depress brake pedal several times firmly to properly
More informationMazda CX7 2010-up 99-7520B
INSTALLATION INSTRUCTIONS FOR PART 99-7520B APPLICATIONS Mazda CX7 2010-up 99-7520B KIT FEATURES DIN radio provision with pocket ISO radio provision with pocket Double DIN radio provision Painted matte
More informationSB-C-CTS/10TW3 SKU# 94552 2008 & Up Cadillac CTS/CTS-V
INSTALLATION GUIDE for the SB-C-CTS/10TW3 SKU# 94552 2008 & Up Cadillac CTS/CTS-V If you choose to perform the installation yourself, it is absolutely vital that the Stealthbox be properly mounted to the
More informationBMW E46 Convertible. Storage Compartment Lid Hydraulic Cylinder Removal
BMW E46 Convertible Storage Compartment Lid Hydraulic Cylinder Removal Created by taylor192 of E46Fanatics.com Hosted by Top Hydraulics, without any warranties Page.1 Storage compartment lid hydraulic
More informationI Click on a link tab to jump to that page. Cover Page
& nstall Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. Factory
More informationMGB Chrome Bumper Conversion
MGB Chrome Bumper Conversion Installation Instructions For 1974 1/2-1980 MGB This kit requires cutting, welding, and painting. Professional installation recommended. Note: Every MGB body is slightly different
More informationRemote Access System Installation
2011-2013 Explorer Remote Access Remote Access System Installation CONTENTS VEHICLE PREPARATION Hood Switch Wire Harness Installation Hood Switch Installation RMST Module Installation RMU Module Installation
More informationSash Replacement Guide
for Andersen 200/400 Series Awning Windows Read all instructions carefully before attempting this procedure. If you have any questions about your ability to complete this procedure, call Andersen at 1-888-888-7020
More informationINSTALLATION INSTRUCTIONS. 6108 Air Spring Kit 2011+ Ford F250 Single Wheel 4WD 2011+ Ford F350 Dually 4WD (2011 F350 Single Wheel 4WD use p/n 6113)
INSTALLATION INSTRUCTIONS 6108 Air Spring Kit 2011+ Ford F250 Single Wheel 4WD 2011+ Ford F350 Dually 4WD (2011 F350 Single Wheel 4WD use p/n 6113) Thank you for purchasing a quality Hellwig Product. PLEASE
More informationVW T5 Airtronic D2 12V Heater Kit Part No.E6175 Installation Instructions
Eberspächer VW T5 Airtronic D2 12V Heater Kit Part No.E6175 Installation Instructions (Use with technical description and instruction maunal) 1 of 15 JJ 22276A 2 of 15 JJ 22276A Remove all screws securing
More informationProjector90 Xenon Headlight Installation Guide
Projector90 Xenon Headlight Installation Guide Written exclusively for Umnitza s Projector90 Product This step-by-step guide is designed to be used in together with other available documentation including
More informationStandard Sleep Pod Side Entry Assembly Instructions
Standard Sleep Pod Side Entry Assembly Instructions www.podtime.co.uk enquiries@podtime.co.uk Working House Ltd How to assemble your pod Pod assembly onsite is a relatively simple exercise for two people
More informationTraditional Sonar and DSI Sonar Installation
Traditional Sonar and DSI Sonar Installation This document covers the installation of the transducer and display unit installation, which includes connecting the unit to power and installing the unit on
More informationMazda CX9 2007-up 99-7516B
INSTALLATION INSTRUCTIONS FOR PART 99-7516B APPLICATIONS Mazda CX9 2007-up 99-7516B KIT FEATURES DIN radio provision with pocket ISO radio provision with pocket Double DIN radio provision Stacked ISO units
More informationSCION FR-S 2013 - PERFORMANCE AIR INTAKE Preparation 2.0L F-4
Preparation 2.0L F-4 Part Number: PTR03-18130 Please see Page 12 for important Care and Maintenance information! Kit Contents Item # Qty. Service Part # Description 1 1 PTR03-18130-AC TRD Air Box Base
More informationINSTALLATION INSTRUCTIONS. 6111 Air Spring Kit 2011+ Ford F250/F-350 Single Wheel 2WD 2011+ Ford F350 Dually 2WD IMPORTANT NOTES
INSTALLATION INSTRUCTIONS 6111 Air Spring Kit 2011+ Ford F250/F-350 Single Wheel 2WD 2011+ Ford F350 Dually 2WD Thank you for purchasing a quality Hellwig Product. PLEASE READ THIS INSTRUCTION SHEET COMPLETELY
More informationRECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
PART NUMBER: 250-9612 GENERAL APPLICABILITY THIS CRUISE WAS TESTED AND VERIFIED ON: FORD FOCUS SE & S MODELS (AT/MT) FORD TRANSIT ALL MODELS RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
More informationBILLET HEADLAMP WITH SHORT/TALL MOUNTS
-J099 REV. 00-0- BILLET HEADLAMP WITH SHORT/TALL MOUNTS GENERAL Kit Number 9-0, 9-0 Models Kit 9-0 is a -/ inch headlamp and kit 9-0 is a -/ inch headlamp. Both kits will fit the models listed in Table.
More informationSECURITY SYSTEM SMART SIREN KIT
-J00876 REV. 009-0-09 SECURITY SYSTEM SMART SIREN KIT GENERAL Kit Number 688-0 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com
More informationVOYAGER 570G. 744A Sprayer Control
VOYAGER 570G 744A Sprayer Control U S E R M A N U A L U S E R M A N U A L Table of Contents CHAPTER 1 - INTRODUCTION...1 SYSTEM CONFIGURATIONS...1 KIT CONTENTS...3 CONTROL HOUSING ASSEMBLY...5 CHAPTER
More informationBULB REPLACEMENT BROCHURE
BULB REPLACEMENT BROCHURE Contents Contents Explanation of Symbols 03 Audi A1 04 06 Audi A4 1.9 TDI with Xenon Headlights (from years of manufacture 2000 to 2005) 07 10 Audi A4 (8K5 / 8K2) with Bi-Xenon
More informationINSTALLATION MANUAL MODEL RP-100
INSTALLATION MANUAL FOR 24 VALVE 5.9L CUMMINS POWERED DODGE TRUCKS 2003 THROUGH 2004.5 MODEL RP-100 READ THESE INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION 5400 BUSINESS 50 WEST SUITE 8 573 635-0555
More information4.3-inch Back-Up Camera
TM 4.-inch Back-Up Camera Model No.: PKC0BU4 Owner s Manual and Warranty Information Read these instructions completely before using this product. Retain this Owner s Manual for future reference. INTRODUCTION
More informationComplete System Shelter
Complete System Shelter For Weather Console Installations The weather resistant Complete System Shelter (CSS) provides protection from the elements for system components such as the Vantage Pro2 and Vantage
More information2002 2005 Mini Cooper S Grille Install Instructions
2002 2005 Mini Cooper S Grille Install Instructions Lower Front Grille BEFORE AFTER Package Contents 1 perforated grille (Stiletto, RAZR, or Monster) 6 Zip Tie Mounting Pads 1 is for the temp. sensor 5
More informationMazda CX7 2007-09 99-7508
INSTALLATION INSTRUCTIONS FOR PART 99-7508 APPLICATIONS Mazda CX7 2007-09 99-7508 KIT FEATURES DIN Radio Provision with Pocket ISO Mount Radio Provision with Pocket Double DIN Mount Radio Provision Stacked
More information