Yamaha Nyrto Turbo Installation Instructions
|
|
- Derick Mason
- 7 years ago
- Views:
Transcription
1 Yamaha Nyrto Turbo Installation Instructions Picture from motor.com
2 Step 1: Turbo Mounting Bracket A. Remove stock header and heat shield. B. Bolt turbo header in place using only two bolts. C. Bolt turbo in place. D. Position turbo mount, and tunnel block-off plate and, mark. E. Remove turbo and header. F. Drill 3/16 holes, and rivet turbo mount and block-off plate in place. Revised 10/02/08 Yamaha Nytro Race Gas Turbo Installation instructions Page 2
3 Step 2: Install Header and Turbo A. Install header using 6 stock header bolts and gasket. B. Bolt turbo to header using 4, 5/16 x1 bolts and lock nuts. C. Fasten turbo support brackets together using rubber mount and lock nuts. (Note: Do not use nylon lock nuts here.) Step 3: Install Oil Return Hose A. Fasten oil hose to drain at bottom of turbo. C. Remove small plastic plug from mag cover. D. Install 90 1/4 npt x 3/8 barb fitting. B. Cover oil return hose with 6 heat insulator. E. Route oil return hose from turbo to mag cover. Revised 10/02/08 Yamaha Nytro Race Gas Turbo Installation instructions Page 3
4 Step 4: Install Turbo Oil Inlet Hose A. Remove 8 mm bolt from cylinder block, located on mag side near throttle body. B. Install 8mm x 4AN fitting and brass washer into cylinder block. C. Route ¼ push-lock hose from cylinder head to turbo using two 90 4 AN x 1/4 barb fitting. D. Shield oil hose at turbo with 6 insulated heat shield. Step 5: Install Exhaust Outlet Pipe A. Using a cutting tool, enlarge exhaust hole in tunnel for exhaust outlet pipe. B. Bolt outlet pipe to turbo using 4-8mm x 25mm bolts, 1-8mm x 40 mm stud and nut Revised 10/02/08 Yamaha Nytro Race Gas Turbo Installation instructions Page 4
5 Step 6: Install Muffler A. Install exhaust intermediate pipe. B. Slide muffler in to intermediate pipe. C. Bolt muffler bracket in place using three 1/4 bolts, nuts and lock washers. D. Bolt muffler to muffler bracket using clamp and 3/8 bolt and nut. A. Step7: Remove Air Box and Throttle Bodies A. Remove steering post. B. Remove air box. C. Remove radiator shroud. D. Remove throttle bodies. E. Reroute harness, and fasten to fan support with factory zip-ties. Revised 10/02/08 Yamaha Nytro Race Gas Turbo Installation instructions Page 5
6 Step 8: Replace Radiator Brackets A. Replace radiator brackets. B. Relocate reverse beeper. Step 9: Install Battery Box A. Relocate relay bracket. B. Remove and omit overflow hose clips. New location Old location C. Install battery box using 1- ¼ bolt and lock nut, 2-3/16 rivets and 2- rubber mounts Revised 10/02/08 Yamaha Nytro Race Gas Turbo Installation instructions Page 6
7 Step 10: Install Boost Lines to Throttle Bodies A. Remove vacuum port plugs and install boost lines and T s to Throttle bodies. Throttle Body Boost Line and T Diagram Boost Ref. to Transducer/ BOV PTO Side B. Secure all boost and vacuum lines to throttle bodys using zip-ties. C. Install BD Control Box injector harness, (see control box instructions). Revised 10/02/08 Yamaha Nytro Race Gas Turbo Installation instructions Page 7
8 Step 11: Install Throttle Bodies A. Rotate fuel rail inlet 180 B. Reinstall throttle bodies Remove screws C. Install machine rings on throttle bodies D. Install control box injector harness (refer to BD control box instructions) Rotate to this position Step 12: Install Turbo Coolant Hoses A. Attach blue coolant hoses to turbo. B. Shield coolant hoses at turbo with 6 insulated heat shields. C. Connect one coolant hose to throttle body. D. Connect the remaining coolant hose to stock throttle body coolant hose using barbed coupler. Revised 10/02/08 Yamaha Nytro Race Gas Turbo Installation instructions Page 8
9 Step 13: Install Upper Steering Post Mounts A. Bolt upper steering post mounts in place, using 5/16x2¾ bolt, 2 washers, lock nut, and stock steering spacer from lower steering block. Drill Here Stock Spacer B. Drill 4 holes for the 4-5/16 x1½ cartage bolts and lock nuts C. Install 4-5/16 x1½ cartage bolts and washers lock nuts, with nuts towards the engine. Revised 10/02/08 Yamaha Nytro Race Gas Turbo Installation instructions Page 9
10 Step 14: Adjust Steering Drag Link A. Set steering riser block in place. B. Install steering post, using stock bolts and spacers at upper mount. C. Install machine nuts, and BD support at bottom mount, omit stock spacers here. D. Adjust drag link so handle bars are straight with skis. E. Once draglink is adjusted, remove steering shaft. Adjust Draglink here Step 15: Install Battery A. Place battery in battery box, and secure in place with rubber strap. B. Route positive cable through hole in frame. C. Use 1 piece of 5/16 hose, and 2 tip ties to protect cable from rubbing on the frame. Revised 10/02/08 Yamaha Nytro Race Gas Turbo Installation instructions Page 10
11 Step 16: Install Negative Battery Cable A. Cut smaller black wire on negative cable. B. Lengthen wire, using 30 piece of 12 gauge black wire, and 2 heat shrink butt connectors. C. Cover edge of battery box, using 2 piece of 1/4 hose. D. Connect battery cable to battery, and white connector. Step 17: Install Intercooler A. Install turn buckle assembly to oil cooler bolt. B. Install intercooler to throttle bodies, fasten in place with turn buckle assembly. C. Connect turbo charger to intercooler, with 7 black silicone hose and 2 clamps. Revised 10/02/08 Yamaha Nytro Race Gas Turbo Installation instructions Page 11
12 Step 18: Assemble Fuel Rail A. Install fuel pressure regulator to fuel rail using 1/8 x1/4 npt male fitting B. Install fuel pressure regulator return (1/8 npt 45 & 1/8 npt x 5/16 barb fittings) Pres. Adj. Boost Ref. Fuel Inlet Fuel Return Note: Use thread sealant at npt connections C. Install 3 auxiliary injectors into fuel rail Step 19: Install BOV and Fuel Rail A. Install BOV (blow-off valve) to intercooler. B. Install fuel rail to intercooler, adjust position of fuel regulator to fit intercooler and cassis, (use 5/16 x1/2 bolts to fasten fuel in place in place). Revised 10/02/08 Yamaha Nytro Race Gas Turbo Installation instructions Page 12
13 Step 20: Bridge Fuel Rails A. Install 1/4 npt x 5/16 barb L fitting to fuel rail. B. Install 5/16 x6 fuel injection (blue liner) hose between L fitting and stock fuel inlet. Note: Use thread sealant at npt connection Step 21: Install Fuel Pump A. Install fuel pump bracket, using stock battery bracket bolt, and threaded mount. B. Install fuel pump to bracket, using #32 hose clamps, with rubber liners supplied with pump. C. Connect fuel pump outlet to fuel rail, using 5/16 x10 fuel injection (blue liner) hose, D. Cut stock fuel pump power harness, use 2 small crimp on eyelets to connect to pump Revised 10/02/08 Yamaha Nytro Race Gas Turbo Installation instructions Page 13
14 Step22: Mount Transducer A. Connect 1/8 npt x 1/8 brass T fitting to transducer. B. Mount transducer, and bracket to coolant overflow bottle, using stock bolt. C. Install auxiliary injector/transducer harness (see BD control box instructions) Note: Use thread sealant at npt connection Step 23: Install Boost Reference A. Connect boost reference hose from throttle bodies, to fuel pressure regulator. B. Cut boost reference hose, between throttle bodies, and fuel regulator, insert transducer. C. Cut boost reference hose, between throttle bodies, and transducer, insert 1/8 x1/8 x3/16 fitting. D. Connect 3/16 hose, from 1/8 x1/8 x3/16 fitting to BOV. E. Secure all hoses to fittings with zip-ties. Transducer Throttle Bodies Fuel Reg. B.O.V. Blow off Valve Fuel Pressure Regulator Transducer Revised 10/02/08 Yamaha Nytro Race Gas Turbo Installation instructions Page 14
15 Step 24: Install Boos Controller A. Mount boost controller to frame, using self tapping screw. B. Connect 3/16 hose from turbo housing fitting, to inlet on boost controller. C. Connect 3/16 hose from outlet of boost controller, to waste gate actuator. D. Secure hose connections using zip-ties. Turbo Housing fitting Step 25: Install Snorkel Ari Filter A. Trim rubber boot to position snorkel air filter. Waste Gate Actuator B. Install snorkel filter and secure with hose clamps. Revised 10/02/08 Yamaha Nytro Race Gas Turbo Installation instructions Page 15
16 Step 26: Install Fuel Gauge Resister A. Locate and cut green 2 wire connector from stock fuel tank leaving 2 of wire B. Strip wire ends and remove green wire from connector C. Solder resister in place between the green and black wires D. Insulate resister, and wires with shrink tube. E. Reinstall green wire to connector. F. Wrap the 2 wires together with another shrink tube, and plug connector into stock harness. Revised 10/02/08 Yamaha Nytro Race Gas Turbo Installation instructions Page 16
17 Step 27: Tape and Drill Fuel Tank A. Apply reflective heat tape to under side of fuel tank B. Drill ½ hole in flat surface at lower mag. side of fuel tank for fuel pick up Fuel Pick up C. Drill ½ hole in upper mag. side of fuel tank for fuel return D. Drill 21/64 hole at top of tank for vent Fuel Return 2 Vent E. Tap vent hole at top of tank to 1/8 NPT F. Clean tank of all debit Revised 10/02/08 Yamaha Nytro Race Gas Turbo Installation instructions Page 17
18 Step 28: Install Fuel Tank Fittings A. Assemble fuel pick up hose using clear hose, pick up screen, and push-in tank fitting. Push in Tank Fitting Pick up Screen B. Install fuel pick up hose assembly, into fuel tank pick up hole, C. Install push-in tank fitting, into fuel tank return hole. D. Install brass barb fitting into taped vent hole. Revised 10/02/08 Yamaha Nytro Race Gas Turbo Installation instructions Page 18
19 Step 29: Mount Fuel Tank A. Drill (4) 1/4 holes in steering hoop, for rubber tank mounts. B. Install (4) rubber mounts C. Install fuel tank and bolt in place Step 30: Install Fuel Hose A. Install 5/16 rubber fuel hose, from fuel tank pick up fitting, to fuel pump inlet. B. Install 5/16 rubber fuel hose, from fuel pressure regulator, to fuel tank return fitting. C. Connect stock vent hose, to fuel tank vent. Revised 10/02/08 Yamaha Nytro Race Gas Turbo Installation instructions Page 19
20 Step 31: Finishing Up A. Install BD control box (see control box instructions). B. Fill fuel tank, with race fuel. C. Adjust idling fuel pressure to 45 psi D. Reinstall seat, headlight assembly, side panels, and hood use stock radiator shroud screws to attach hood to fuel tank. Revised 10/02/08 Yamaha Nytro Race Gas Turbo Installation instructions Page 20
A&A CORVETTE PERFORMANCE C6 BOOST & FUEL GAUGE INSTALLATION INSTRUCTIONS
A&A CORVETTE PERFORMANCE C6 BOOST & FUEL GAUGE INSTALLATION INSTRUCTIONS 1. Check your gauges before you take them out of the packaging to make sure they are at 0 (zero) psi for both boost and fuel pressure.
More informationREMOVAL AND INSTALLATION
303-01C-1 REMOVAL AND INSTALLATION Engine Body On Special Tool(s) Adapter For 303-D043 303-D043-02 or equivalent Special Tool(s) 303-01C-1 Turbocharger Lifting Bracket 303-1266 Wrench, Fan Clutch Nut 303-214
More informationPower Cube Open Source Ecology Page 1. Power Cube. Version 4
Power Cube Open Source Ecology Page 1 Power Cube Version 4 Power Cube Open Source Ecology Page 2 Contents Table of Contents Power Cube... 1 Contents...2 Introduction... 3 Bill Of Materials...4 Discrete
More informationVOYAGER 570G. 744A Sprayer Control
VOYAGER 570G 744A Sprayer Control U S E R M A N U A L U S E R M A N U A L Table of Contents CHAPTER 1 - INTRODUCTION...1 SYSTEM CONFIGURATIONS...1 KIT CONTENTS...3 CONTROL HOUSING ASSEMBLY...5 CHAPTER
More informationwith installation dynafact boost GAUGE this manual is for use with systems 64050-64054
owners manual with installation instructions dynafact boost GAUGE this manual is for use with systems 64050-64054 GENERAL INSTALLATION PRACTICES This manual is an installation guide for all 1. Banks DynaFact
More informationPSS10H/B PSS12H/A ILLUSTRATED PARTS LISTS
PSS10H/B PSS12H/A ILLUSTRATED PARTS LISTS AC AND DC GENERATOR SCHEMATIC ENGINE GENERATOR ASSEMBLY REF Description QTY PSS10 PSS12 1 Engine, Honda GX620K1VXC2 Code 637220 1 99779-000 GX670VXC2 Code 637220
More informationBefore installation it is important to know what parts you have and what the capabilities of these parts are.
INSTALLATION GUIDE Before installation it is important to know what parts you have and what the capabilities of these parts are. The Recon XZT is the smallest and most powerful gauge of its kind. With
More informationINSTALL INSTRUCTIONS KK-C-HVAC-1 HVAC UNIT 2003-2014 CHEVROLET/GMC VANS FOR
INSTALL INSTRUCTIONS KK-C-HVAC-1 HVAC UNIT 2003-2014 CHEVROLET/GMC VANS FOR (For NEW 2007 ALL WHITE KWIK-KITS ONLY) Warning do not attempt to install A/C units unless you are experienced with servicing
More information2003 ACCORD - Automatic Transmission Removal
2003 ACCORD - Automatic Transmission Removal Special Tools Required Engine support hanger, A and Reds AAR-T-12566 Engine hanger balancer bar VSB02C000019 Front subframe adapter VSB02C000016 These special
More informationAir Vantage 500 Kubota
Illustration of Sub Assemblies Illustration of Sub Assemblies Illustration of Sub Assemblies Illustration of Sub Assemblies P-625 P-625 RETURN TO MAIN INDEX PARTS LIST FOR Air Vantage 500 Kubota P-625-A
More informationFigure 2 The fan and shroud also needs to be removed for access to the four a/c compressor bolts and removal of the compressor from the top.
Here are some pictures to show what s required when replacing the A/C compressor, expansion valve and receiver/drier on a 2001 Volvo V70. Even if you don t replace these A/C parts these pictures can help
More informationKatana Supercharger Installation Instructions Rev. E Page 1 of 23
Katana Supercharger Installation Instructions Rev. E Page 1 of 23 READ FITTING INSTRUCTIONS IN FULL BEFORE INSTALLATION This article is sold without warranty expressed or implied. No warranty or representation
More informationINSTALLATION MANUAL MODEL RP-100
INSTALLATION MANUAL FOR 24 VALVE 5.9L CUMMINS POWERED DODGE TRUCKS 2003 THROUGH 2004.5 MODEL RP-100 READ THESE INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION 5400 BUSINESS 50 WEST SUITE 8 573 635-0555
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Application Outboards Faria 5 Gauge Set* Publication No. Description Part Number Honda Code PII53606A White faced, flat lens 06300-ZW5-010ZB 6315410 Issue Date Black faced, flat
More informationSolstice/Sky Water Pump Replacement
Solstice/Sky Water Pump Replacement The water pump on the Solstice/Sky is starting to need replacement on some vehicles. This guide will help in replacing the water pump while the engine is still in the
More informationENGINE FUEL FUEL FILTER... FUEL HEATER... INJECTOR... SUPPLY PUMP... COMMON RAIL... FUEL PRESSURE LIMITTER...
FUEL FILTER............................ FUEL HEATER.......................... INJECTOR.............................. SUPPLY PUMP.......................... COMMON RAIL.......................... FUEL PRESSURE
More informationADDING AN ELECTRIC AUXILIARY FAN TO RADIATOR STACK ON 03 ALPINE COACH
ADDING AN ELECTRIC AUXILIARY FAN TO RADIATOR STACK ON 03 ALPINE COACH The original design of the 03 Alpine Coaches (and perhaps other years as well) did not include any kind of engine fan engage mechanism
More informationBR150 Pmi Baja Reaction 150cc Go Kart (VIN PREFIX L4VM)
Page 1 of 21 Product Information Baja Web > Product Information > Parts Lists > GOKART > BR150 Pmi Baja Reaction 150cc Go Kart (VIN PREFIX L4VM) BR150 Pmi Baja Reaction 150cc Go Kart (VIN PREFIX L4VM)
More informationCOOLING SYSTEM Section Page
5 COOLING SYSTEM Section Page 5.1 COOLANT PRE-HEATER... 5-3 5.2 COOLANT PUMP NON-EGR ENGINE... 5-7 5.3 COOLANT PUMP EGR ENGINE... 5-13 5.4 FRONT CONNECTOR HOUSING NON-EGR ENGINE... 5-17 5.5 FRONT CONNECTOR
More information2700 DUST CONTROL MACHINE:
700 DUST CONTROL MACHINE: 30016 PAGE 1 700 DUST CONTROL MACHINE: 30016 11 17 9 15 8 16 10 1 13 7 6 1 1 30 OLD STYLE BATERY BOX 8 3 5 3 7 0 18 19 31 3 9 5 1 FACTORY INSTALLED OPTIONS: 30011 ELECTRIC CLUTCH
More informationTurbocharger system components, servicing
21-1 Turbocharger system components, servicing Engine codes: AAZ, 1Z, AHU Observe rules of cleanliness Page 21-10 Turbocharger hoses and lines, connecting Page 21-11 WARNING! Do not re-use any fasteners
More informationCoolant heater. Thermo Top - Z/C additional heating system. Installation instructions. Volvo S60, Volvo V70, and Volvo S80 Beginning Model Year: 2000
Coolant heater Thermo Top - Z/C additional heating system Approval code ~~~ S 9 Installation instructions Volvo S60, Volvo V70, and Volvo S80 Beginning Model Year: 000 6 6 7 8 Volvo XC70 Beginning Model
More informationMAN - MERCEDES - BENZ
SAYFA: 1 10100 10102 10103 355 353 06 15 355 353 03 15 346 353 08 15 AXLE GEAR AXLE GEAR AXLE (WITH BUSHING TYPE) (WITH BUSHING TYPE) (WITH BUSHING TYPE) 2521 2517-2521-2622 10104 10105 10106 308 350 00
More informationINSTALLATION INSTRUCTIONS. 6108 Air Spring Kit 2011+ Ford F250 Single Wheel 4WD 2011+ Ford F350 Dually 4WD (2011 F350 Single Wheel 4WD use p/n 6113)
INSTALLATION INSTRUCTIONS 6108 Air Spring Kit 2011+ Ford F250 Single Wheel 4WD 2011+ Ford F350 Dually 4WD (2011 F350 Single Wheel 4WD use p/n 6113) Thank you for purchasing a quality Hellwig Product. PLEASE
More informationINSTALLATION MANUAL MODEL RP-150
INSTALLATION MANUAL FOR 24 VALVE 5.9L CUMMINS POWERED DODGE TRUCKS 2003 THROUGH 2004.5 MODEL RP-150 READ THESE INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION 5400 BUSINESS 50 WEST SUITE 8 573 635-0555
More informationFor a simple splice connection look at figure 21. This basic type of splice can be used almost exclusively when hooking up your wiring.
Page 1 of 10 IMPORTANT: Before starting installation, please be sure that all items which were supplied with the kit are accounted for. Note: These instructions are to be used in conjunction with the instructions
More informationPERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1967 CHEVROLET IMPALA
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1967 CHEVROLET IMPALA CONTROL & OPERATING INSTRUCTIONS The controls on your new
More informationIntake Manifold: Service and Repair
2000 Chevy Truck S10/T10 P/U 2WD L4-2.2L VIN 4 Copyright 2008, ALLDATA 9.90 Page 1 Intake Manifold: Service and Repair Removal Procedure 1. Disconnect the battery negative cable. Refer to Battery Replacement.
More informationRail 001 112 2 Canvas, folding top 001 101 3 Rear panel 001 102 4 Stip in window, left 001 106 dto. right 001 107
U 411 1 Rear view mirror, round, metall 13cm Ø 002 045 2 Raised airintake 002 060 3 Side panelling, front, left 002 030 Side panelling, front, right 002 031 4 Panelling left 002 051 dto. right 002 052
More information2740 Whitten Rd Bldg 103 Memphis, TN 38133 Telephone 901-380-9290 Email Bwilliams@Dieselcare.net
Fuel Injection Pump Replacement REMOVAL Diesel Care & Performance Inc 1. Disconnect negative battery terminal. 2. Remove throttle linkage. Fuel Injection Pump Bracket 3. Remove injection pump bracket.
More informationEquipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-754DS. 2012-2015 BMW 335i 3.0L
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-754DS 2012-2015 BMW 335i 3.0L 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2057DK AIR FILTER 1 2 9-0442 TUBE;
More information830-II *330492* Cummins 4 Cylinder Engine Breakdown. 330492 Rev. 00
830-II Cummins 4 Cylinder Engine Breakdown 330492 Rev. 00 *330492* This manual is furnished with each new TENNANT Model 830. This manual consists of the 4 Cylinder Cummins Engine Breakdown. MACHINE DATA
More informationBUGGY SETUP GUIDE. Volume GOKARTSUSA GY6 150, CN250. Buggy Setup Guide
BUGGY SETUP GUIDE Volume 1 GOKARTSUSA GY6 150, CN250 Buggy Setup Guide GY6 150, CN250 DUNE BUGGY Buggy Setup Guide GOKARTSUSA.COM 2000 Highway 50 S. Lake Tahoe, CA 96150 Phone 800.603.1437 2 Table of Contents
More informationINSTALLATION INSTRUCTIONS. 6111 Air Spring Kit 2011+ Ford F250/F-350 Single Wheel 2WD 2011+ Ford F350 Dually 2WD IMPORTANT NOTES
INSTALLATION INSTRUCTIONS 6111 Air Spring Kit 2011+ Ford F250/F-350 Single Wheel 2WD 2011+ Ford F350 Dually 2WD Thank you for purchasing a quality Hellwig Product. PLEASE READ THIS INSTRUCTION SHEET COMPLETELY
More informationXL PREMIUM OIL COOLER KIT
-J05 REV. 0-0-0 XL PREMIUM OIL COOLER KIT GENERAL Kit Number 0008 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English
More information356 CHECKLIST ELECTRICAL: CHASSIS:
356 CHECKLIST ELECTRICAL: Headlights hi/lo beam Taillights Running lights Turn signals Brake lights License light(s) Fog lights Reverse light Horn Dome lights Dash lights Temp guage Tank level guage Tachometer
More informationMGA Alternator Conversion
MGA Alternator Conversion Installation Instructions For 1955 to 1962 MGA PART # 130-078 and #130-088 440 Rutherford St. P.O. Box 847 Goleta, CA 93117 1-800-667-7872 FAX 805-692-2525 www.mossmotors.com
More information1998½-2007 Dodge Ram 5.9L Cummins
9 January 2014 1081130-33 Dodge Cummins Low Fuel Pressure Alarm Light Kit (I-00143) 1 1998½-2007 Dodge Ram 5.9L Cummins LOW FUEL PRESSURE ALARM LIGHT - Installation Manual - Part Number Sequence: 1081130
More informationM-9424-463V Intake Manifold INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationVW GOLF Mk4 TDI FRONT MOUNTING INTERCOOLER INSTALLATION INSTRUCTIONS
VW GOLF Mk4 TDI FRONT MOUNTING INTERCOOLER INSTALLATION INSTRUCTIONS Tools required: 10mm/13mm socket and 3/8 drive ratchet with extension Torx T20/25/30 screwdrivers or bits Phillips head screwdriver,
More information1/29/2008 DR50. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PART NUMBERS PRICES ARE SUBJECT TO CHANGE 1 of 45
DR50 Toll Free: 888-863-2252 PART NUMBERS PRICES ARE SUBJECT TO CHANGE 1 of 45 CYLINDER & CYLINDER HEAD Part UPC Number Description Baja Description 1 DR50-001 842645074424 CYLINDER 1 1 2 DR50-002 842645074431
More informationSlide the new steering column shaft through the steering column from the driver compartment.
Slide the new steering column shaft through the steering column from the driver compartment. Push the column shaft through the steering column until the machined end is out past the column lower bushing.
More informationNot required for most applications Not required for most applications High pressure (12-803 provided) High pressure (12-803 provided)
ELECTRIC FUEL PUMPS P/N 12-801-1, 712-801-1, 12-802-1, 712-802-1, 12-815-1, & 712-815-1 FUEL PRESSURE REGULATORS P/N 12-803, 12-501, 12-804, 12-500, & 15812NOS Installation Instructions THESE INSTRUCTIONS
More informationM-9000-ZX3 JRSC Focus Big Boost Upgrade Kit INSTALLATION INSTRUCTIONS
Please contact the Tech Hot Line for the most current instruction information (586) 468-1356!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! INTRODUCTION: These instructions
More informationWalbro 255lph Inline Fuel Pump Install Procedure
Walbro 255lph Inline Fuel Pump Install Procedure Note: Instructions are based on a single in tank pump with under car OEM VW filter. Total install time for a qualified technician is approximately 2 hrs.
More informationLIMITED LIFETIME WARRANTY
P D09 095G LIMITED LIFETIME WARRANTY SERIAL NO. MANUFACTURED DATE: MOTOR NO: WARRANTY STIPULATIONS: Copy of sales receipt mailed with this form All warranty information, located on back, completely filled
More information1/29/2008 DR125 / DR150. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PARTS AND PRICES ARE SUBJECT TO CHANGE 1 of 55
DR125 / DR150 Toll Free: 888-863-2252 PARTS AND PRICES ARE SUBJECT TO CHANGE 1 of 55 CYLINDER HEAD ASSY. 1 125-001 883099006937 CYLINDER HEAD COVER 1 1 2 125-002 883099006944 BOLT M6X28 2 3 3 125-003 883099006951
More informationK&T Saw Shop 606-678-9623 or 606-561-4983
13-600072-06 PRO MAC 8200 05/92 to Current IPL 215710-02 Page 1 of 20 Carburetor Assembly www.ktoutdoor.com 13-600072-06 PRO MAC 8200 05/92 to Current IPL 215710-02 Page 2 of 20 Carburetor Assembly 214763-02
More informationDR90. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PART NUMBERS AND PRICES ARE SUBJECT TO CHANGE 1 of 51
DR90 Toll Free: 888-863-2252 PART NUMBERS AND PRICES ARE SUBJECT TO CHANGE 1 of 51 CYLINDER & CYLINDER HEAD 1 DR90-001 842645048166 CYLINDER 1 1 2 DR90-002 842645048173 GASKET, CYLINDER 1 1 3 DR90-003
More informationCooling system components, removing and installing
Engine BHW Cooling system components, removing and installing Page 1 / 24 19-1 Cooling system components, removing and installing Warning! When doing any repair work, especially in the engine compartment,
More informationspecializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1967-72 CHEVROLET PICKUP
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1967-72 CHEVROLET PICKUP CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect
More informationDR50 Hensim Dirt Runner 49cc Dirt Bike (VIN PREFIX LLCH or LUAH)
Page 1 of 21 Product Information Baja Web > Product Information > Parts Lists > DIRTBIKE > DR50 Hensim Dirt Runner 49cc Dirt Bike (VIN PREFIX LLCH or LUAH) DR50 Hensim Dirt Runner 49cc Dirt Bike (VIN PREFIX
More informationVolkswagen B3 Passat General-Engine 4 CYL. 19 Engine - Cooling System (Page GR-19)
19 Engine - Cooling System (Page GR-19) Cooling system draining and filling general information Body components, layout Engine components, layout Radiator fan run-on checking Recommended mixture ratios
More informationGEET Fuel Processor Plans
GEET Fuel Processor Plans This is a greatly simplified Proof of Concept version of the GEET Fuel Processor that just about anyone can build from parts from a local Hardware store in a weekend for very
More informationDR125 and DR150 Hensim Dirt Runner 125cc and 150cc Dirt Bike (VIN PREFIX LLCH or LUAH)
Parts Lists - DR125 and DR150 Hensim Dirt Runner 125cc and 150cc Dirt Bike (VIN PR... Page 1 of 25 Product Information Baja Web > Product Information > Parts Lists > DIRTBIKE > DR125 and DR150 Hensim Dirt
More informationInstalling a new 928 Motorsports All-Aluminum Radiator
928 Motorsports Supercharger Installation Copyright 2008, 928 Motorsports, LLC All Rights Reserved Installing a new 928 Motorsports All-Aluminum Radiator Copyright 2008 928 Motorsports, LLC. Toll-Free
More informationOVEN PARTS For Models:GSC308PJB05, GSC308PJQ05, GSC308PJT05, GSC308PJS05 (Black) (White) (Biscuit) (Black Stainless)
OVEN PARTS 30" BUILT IN ELECTRIC COMBO SENSOR/SC (GOLD LINE) 3 05 Litho In U.S.A. (cre) 1 Part No. Rev.A OVEN PARTS 1 Literature Parts 4455994 Installation Instructions Use & Care Guide 8300346 Microwave
More information11-600036D PRO MAC 60 07/72 to 12/76 IPL 89321 Page 1 of 19 Accessories
11-600036D PRO MAC 60 07/72 to 12/76 IPL 89321 Page 1 of 19 Accessories 11-600036D PRO MAC 60 07/72 to 12/76 IPL 89321 Page 2 of 19 Accessories 84453 Kit - Piston tool 69191 Kit - Pressure test adaptor
More informationVolkswagen Jetta, Golf, GTI 1999, 2000 2.8 Liter VR6 2V Engine Mechanical, Engine Code(s): AFP 17 Engine-Lubrication (Page GR-17)
17 Engine-Lubrication (Page GR-17) Lubrication system components, removing and installing Oil filter housing, disassembling and assembling Oil pan, removing and installing Oil pressure and oil pressure
More informationK&T Saw Shop 606-678-9623 or 606-561-4983
12-600072F PRO MAC 850 SUPER CHAIN SAW 05/92 to Current IPL 215710-R1 Page 1 of 16 Accessories www.ktoutdoor.com 12-600072F PRO MAC 850 SUPER CHAIN SAW 05/92 to Current IPL 215710-R1 Page 2 of 16 Accessories
More informationSALEEN SPEEDLAB SERIES VI STANDARD SC UPGRADE KIT
SALEEN SPEEDLAB SERIES VI STANDARD SC UPGRADE KIT INSTALLATION MANUAL: 2005 MUSTANG 4.6 3V MANUAL P/N: 10-8002-C14338C SUPERCHARGER KIT P/N: 10-1607-B14083* Saleen Performance, Inc. 1225 East Maple Rd.,
More informationFRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER
Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER Please read before beginning Stainless steel hardware
More informationUniversal Adjustable Fuel Pressure Regulator
Universal Adjustable Fuel Pressure Regulator Installation Instructions for: Part Numbers 25-302 U.S. Patent # 6,298,828! Due WARNING: to the fact that this installation deals with your fuel system this
More information- power windows - alarm system - electric door mirror control - door warning light - central locking - seat memory
Door Wiring Harness Plug Connections Binder -, Electrics Vehicle Type: (86) Model Year: 7 (V) Concern: Door wiring harness plug connections X11 / X12. Information: The rubber boot for the door connector
More informationOperations Manual SledStart H4 HID Light Kit
Operations Manual SledStart H4 HID Light Kit ` Table of Contents INTRODUCTION...1 SAFETY WARNING...1 PACKAGE CONTENTS...1 INSTALLATION INSTRUCTIONS...2 NOTES... 7 Copyright 2010 SledStart LLC All Rights
More informationCooling system components
Page 1 / 33 19-1 Cooling system components Caution! When doing any repair work, especially in the engine compartment, pay attention to the following due to clearance issues: Route lines of all types (e.g.
More informationINSTALLATION INSTRUCTIONS FOR 2006-2009 VW MK5
CI100018 INSTALLATION INSTRUCTIONS FOR 2006-2009 VW MK5 Rabbit, Jetta 2.5L These instructions are applicable to vehicles equipped with either manual or automatic transmissions Thank you for choosing to
More informationhttp://waterheatertimer.org/troubleshoot-rheem-tankless-water-heater.html
http://waterheatertimer.org/troubleshoot-rheem-tankless-water-heater.html TECHNICAL SERVICE DEPARTMENT Removal, Cleaning, & Reinstallation of the Burner Assembly For models 74 & GT199 Required tools -
More informationImportant: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks
TITAN pt. no.: 03 0000 0120 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended
More informationVW Caddy W21-760-3503 INSTALLATION INSTRUCTIONS
Unit 626 Kilshane Avenue, North West Business Park, Ballycoolin, Dublin 15, Ireland Telephone: +353 1 8612 632, Fax: +353 1 8612 647, email: sales@driveriteltd.com www.driveriteltd.com VW Caddy W21-760-3503
More information46431x92A Garden Tractor (1998) Page 1 of 16 Body Chassis
46431x92A Garden Tractor (1998) Page 1 of 16 Body Chassis 46431x92A Garden Tractor (1998) Page 2 of 16 Body Chassis 1 092546E701 Bracket, Seat 2 091963 Z Plate Assembly, Switch 3 164X26 Spring, Compression
More informationTITAN Fuel Tanks. INSTALLATION INSTRUCTIONS G e n e r a t i o n V
TITAN pt. no.: 02 0000 0143 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 26327 2004 S2000 Issue Date OCT 2004 PARTS LIST Security System: P/N 08E51-S84-100 Attachment Kit: P/N 08E55-S2A-101 2 Remote controls
More informationH41 Electrical Stage Aft Air Conditioner Unit Installation
Aft Air Conditioner Unit Installation 1. Place Air-Cond unit in A/C shelf with air return facing fwd direction of the boat. 2. Do not secure Air-Cond Unit on shelf, install both side of air condition ABS
More informationTechnical Guide 08/15/14
Technical Guide 08/15/14 1 Table of Contents Contact information.3 Identifying your system..4-8 Model Number Serial number location Parts of your fuel system..9-14 Fuel pump diagram Wire harness schematics
More informationTOYOTA TUNDRA 2015 Billet Grille w/led DRL
TOYOTA TUNDRA 2015 Billet Grille w/led DRL Part Number: 00016-34088 Accessory Code: BG3000 Conflicts Models 1794 and Platinum Kit Contents Item # Quantity Reqd. Description 1 2 LED DRL 2 1 Driver Box 3
More informationVolkswagen New Beetle 2.0 Liter 4-cyl General, Engine (Engine Code AEG) 17 Engine-Lubrication system (Page GR-17)
17 Engine-Lubrication system (Page GR-17) Lubrication system components, removing and installing Oil pan, removing and installing Oil pressure and oil pressure switch, checking Dynamic oil pressure warning
More informationDR90. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PART NUMBERS AND PRICES ARE SUBJECT TO CHANGE 1 of 51
DR90 Toll Free: 888-863-2252 PART NUMBERS AND PRICES ARE SUBJECT TO CHANGE 1 of 51 CYLINDER & CYLINDER HEAD Part UPC Number Description Baja Description 1 DR90-001 842645048166 CYLINDER 1 1 2 DR90-002
More informationLG G5 Chassis Brace Gen 5 Camaro THE MOST POWERFUL HEADERS ON THE PLANET Brought to you by LG Motorsports 972-429-1963
LG G5 Chassis Brace Gen 5 Camaro THE MOST POWERFUL HEADERS ON THE PLANET Brought to you by LG Motorsports 972-429-1963 Thank you for purchasing LG Motorsports products for your Gen 5 Camaro. Parts Inventory:
More information16 March 2015 1045440-2003-2007 r700 Dodge Cummins Primary Upgrade (I-00279) 1 P/N# 1045440
16 March 2015 1045440-2003-2007 r700 Dodge Cummins Primary Upgrade (I-00279) 1 Dodge Cummins (2003-07) R700 Primary Turbocharger Upgrade Kit P/N# 1045440 - Installation Manual - Please read all instructions
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Handle Camera Mirror Display 2004-2014 Ford F-150 and 2008-2015 Ford Super Duty (Kit part numbers 9002-9521) Kit Contents: Mirror Tailgate Handle with camera and harness Interior
More informationMDT5N25 & MTD5N40 SERVICE PARTS
MDTN & MTDN0 SERVICE PARTS This parts list contains the service parts and wiring diagrams for this model. Check the model number of the machine requiring the parts to be sure that this is the correct parts
More informationINSIDE ENGINE COMPARTMENT TOYOTA AIR CONDITIONING ENGLISH EUROPE,GENERAL,AUSTRALIA
INSIDE ENGINE COMPARTMENT TOYOTA AIR CONDITIONING ENGLISH EUROPE,GENERAL,AUSTRALIA INTRODUCTION IMPORTANT NOTICE This manual has been designed for technicians who are qualified and educated in the proper
More informationDraining and filling cooling system
Page 1 of 9 Draining and filling cooling system Special tools and workshop equipment required Adapter -V.A.G 1274/8- Pipe -V.A.G 1274/10- Drip tray -V.A.G 1306- or drip tray for workshop hoist -VAS 6208-
More informationENGINE Dinli 904 D1033-011
ENGINE Dinli 904 D1033-011 ENGINE Model Item Part no Description Specification Quantity 01 E140000-01 E14 ENGINE 450C.C. 1 FENDER SEAT D1033-021 FENDER SEAT Model Item Part no Description Specification
More information1/29/2008 DR70. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PART NUMBERS PRICES ARE SUBJECT TO CHANGE 1 of 43
DR70 Toll Free: 888-863-2252 PART NUMBERS PRICES ARE SUBJECT TO CHANGE 1 of 43 CYLINDER & CYLINDER HEAD 1 DR70-001 883099044472 CYLINDER 1 1 2 DR70-002 883099044489 GASKET, CYLINDER 1 1 3 DR70-003 883099044496
More information1 5 05-12 5 05-12. Additions, Revisions, or Updates
5 05-12 1 5 05-12 SUBJECT DATE Cylinder Head May 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0023 EPA04 MBE 4000 Cylinder Head Additional
More informationSALEEN SPEEDLAB SUPERCHARGER
SALEEN SPEEDLAB SUPERCHARGER R INSTALLATION MANUAL: 1999-2001 Mustang 4.6L 2V Saleen Performance, Inc. 1225 East Maple Rd. Troy, MI 48083 248-743-4800 www.saleen.com IF YOU ARE NOT EXPERIENCED IN THE AREA
More informationActuator-Swirl Valve DESCRIPTION
US/Canadian 2007 Sprinter Diesel V6 Dodge Service Manual Swirl Valve Info Actuator-Swirl Valve DESCRIPTION The swirl valve linkage links the swirl valves in the intake manifold to the swirl valve actuator.
More informationP7100 PUMP INSTALLATION INSTRUCTIONS Diesel Care & Performance Inc
P7100 PUMP INSTALLATION INSTRUCTIONS Diesel Care & Performance Inc Installation Timing Pin Location CAUTION: Before installing the injection pump, be sure that number 1 cylinder is at the Top Dead Center
More informationMAKE OF AUTOMOBILE: NUMBER : 076/0800901 DATE : 2008-12-08 Copyright Prins Autogassystemen B.V. 2008 VERSION NR : 2008-10-24 B
MAKE OF AUTOMOBILE: HONDA TYPE: CIVIC PISTON DISPLACEMENT: 1800 NUMBER OF VALVES: 16 ENGINE NUMBER: R18A TYPE VSI INJECTOR ( COLOR ) ORANGE MODEL YEAR: 2008 ENGINE SET NUMBER 348/0250200.07 NUMBER : 076/0800901
More informationInstallation Guide 2010 BMW S1000RR Full Exhaust System
Installation Guide 2010 BMW S1000RR Full Exhaust System!! THIS PRODUCT IS DESIGNED FOR USE IN CLOSED COURSE RACING AND IS NOT INTENDED FOR HIGHWAY USE!! Congratulations on the purchase of your new TaylorMade
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII23628 2003 PILOT Issue Date MAY 2002 PARTS LIST Security System Kit (sold separately): P/N 08E51-S84-100 2 Remote controls Attachment
More informationCooling system components, servicing
19-1 Cooling system components, servicing WARNING! The cooling system is pressurized when the engine is warm. When opening the expansion tank, wear gloves and other appropriate protection, cover the cap
More informationAM/FM ANTENNA KIT (TOUR-PAK MOUNT)
-J077 REV. 008-0-0 AM/FM ANTENNA KIT (TOUR-PAK MOUNT) GENERAL Kit Number 7-98A Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com
More informationAFE424 SERVICE PARTS
This is the parts list for the AFE. When looking up part numbers, always check the complete model and serial numbers to be certain of ordering the correct parts. The Air Cooled model has also been manufactured
More informationNumber Wheeler P/N Description Set Rex P/N Notes 1 603500 Base 1 J001 2 603501 Support, Right 1 J002 3 603502 Support, Left 1 J003 4 600328 Nut (M8)
1 603500 Base 1 J001 2 603501 Support, Right 1 J002 3 603502 Support, Left 1 J003 4 600328 Nut (M8) 4 5 600130 Spring Washer (8mm) 4 6 600344 Roll Pin (M6x30) 4 7 600129 Socket Hd Cap Screw (M8x25) 4 8
More information11. COOLING SYSTEM 11-0 COOLING SYSTEM BET & WIN 50
11 COOLING SYSTEM SERVICE INFORMATION------------------------------------------------ 11-1 TROUBLESHOOTING----------------------------------------------------- 11-1 RADIATOR ------------------------------------------------------------------
More informationSTEERING SYSTEM - POWER
STEERING SYSTEM - POWER 1990 Nissan 240SX 1990 STEERING Nissan - Power Rack & Pinion Axxess, Maxima, Pulsar NX, Sentra, Stanza, 240SX, 300ZX DESCRIPTION The power steering system consists of a rack and
More information