tended Environment +85 C -40 C -40 F +185 F Peak Current

Transcription

1 Description Power Range The PWM servo drive is designed to drive brushless DC motors at a high switching frequency. To increase system reliability and to reduce cabling costs, the drive is designed for direct integration into your PCB. The AZXB30A8 is fully protected against over-voltage, under-voltage, over-current, over-heating and short-circuits. A single digital output indicates operating status. The drive interfaces with digital controllers that have analog ±10V output. This servo drive requires only a single unregulated isolated DC power supply, and is fully RoHS (Reduction of Hazardous Substances) compliant. Peak Current Continuous Current Supply Voltage 25 A 12.5 A VDC The conforms to the following specifications and is designed to the Environmental Engineering Considerations as defined in ML-STD-810F. Extended Environment Performance Ambient Temperature -40 C to +85 C (-40 F to +185 F) Storage Temperature -50 C to +100 C (-58 F to +212 F) Thermal Shock -40 C to +85 C (-40 F to +185 F) in 2 min. Relative Humidity 0 to 95% Non-Condensing -40 C E tended +85 C Vibration 30 Grms for 5 min. in 3 axes -40 F Environment +185 F See Part Numbering nformation on last page of datasheet for additional ordering options. Features High Power Density Compact Size Direct Board-to-Board ntegration Lightweight High Switching Frequency Four Quadrant Regenerative peration Wide Temperature Range High Performance Thermal Dissipation Differential nput Command Current Monitor utput Digital Fault utput Monitor 12VDC peration HARDWARE PRTECTN ver-voltage Under-Voltage ver-current ver-temperature Short-circuit (phase-phase) Short-circuit (phase-ground) NPUTS/UTPUTS Digital Fault utput Digital nhibit nput Analog Current Monitor Analog Command nput Analog Current Reference FEEDBACK SUPPRTED Hall Sensors MDES F PERATN Current CMMUTATN Trapezoidal MTRS SUPPRTED Three Phase (Brushless) Single Phase (Brushed, Voice Coil, nductive Load) CMMAND SURCE ±10 V Analog CMPLANCES & AGENCY APPRVALS UL cul CE Class A (LVD) CE Class A (EMC) RoHS ML-STD-810F (as stated) ML-STD-1275D (optional) ML-STD-461E (optional) ML-STD-704F (optional) ML-HDBK-217 (optional) Page 1 of 7

2 BLCK DAGRAM nformation on Approvals and Compliances US and Canadian safety compliance with UL 508c, the industrial standard for power conversion electronics. UL registered under file number E Note that machine components compliant with UL are considered UL registered as opposed to UL listed as would be the case for commercial products. Compliant with European CE for both the Class A EMC Directive 2004/108/EC on Electromagnetic Compatibility (specifically EN :2007 and EN :2005) and LVD requirements of directive 2006/95/EC (specifically EN :2006), a low voltage directive to protect users from electrical shock. ML-STD-810F ML-STD-1275D ML-STD-461E ML-STD-704F ML-HDBK-217 Environmental Engineering Considerations and Laboratory Tests (as stated) Characteristics of 28 Volt DC Electrical Systems in Military Vehicles (optional) Requirements for the Control of Electromagnetic nterference Characteristics of Subsystems and Equipment (optional) Aircraft Electric Power Characteristics (optional) Reliability Prediction of Electronic Equipment (MTBF) (optional) RoHS (Reduction of Hazardous Substances) is intended to prevent hazardous substances such as lead from being manufactured in electrical and electronic equipment. (optional) Page 2 of 7

3 SPECFCATNS Power Specifications Description Units Value DC Supply Voltage Range VDC DC Bus Under Voltage Limit VDC 9 DC Bus ver Voltage Limit VDC 88 Maximum Peak utput Current 1 A 25 Maximum Continuous utput Current A 12.5 Maximum Continuous utput Power W 950 Maximum Power Dissipation at Continuous Current W 50 Minimum Load nductance (Line-To-Line) 2 µh 100 nternal Bus Capacitance 3 µf 30 Low Voltage Supply utputs - +6 VDC (30 ma) Switching Frequency khz 31 Control Specifications Description Units Value Command Sources - ±10 V Analog Feedback Supported - Halls Commutation Methods - Trapezoidal Modes of peration - Current Motors Supported - Three Phase (Brushless), Single Phase (Brushed, Voice Coil, nductive Load) Hardware Protection - nvalid Commutation Feedback, ver Current, ver Temperature, ver Voltage, Under Voltage, Short Circuit (Phase-Phase & Phase-Ground) Mechanical Specifications Description Units Value UL, cul, CE Class A (EMC), CE Class A (LVD), RoHS, ML-STD-810F (as stated), Agency Approvals - ML-STD-1275D (optional), ML-STD-461E (optional), ML-STD-704F (optional), ML-HDBK-217 (optional) Size (H x W x D) mm (in) 76.2 x 50.8 x (3 x 2 x 0.9) Weight g (oz) (4.2) Baseplate perating Temperature Range 4 C ( F) ( ) Ambient Temperature Range C ( F) ( ) Storage Temperature Range C ( F) ( ) Thermal Shock C ( F) ( ) in 2 minutes Vibration Grms 30 for 5 minutes in 3 axes Relative Humidity % Non-Condensing Form Factor - PCB Mounted P1 Connector - 16-pin, 2.54 mm spaced header P2 Connector - 22-pin, 2.54 mm spaced, dual-row header P3 Connector - 22-pin, 2.54 mm spaced, dual-row header Notes 1. Maximum duration of peak current is ~2 seconds. Peak RMS value must not exceed continuous current rating of the drive. 2. Lower inductance is acceptable for bus voltages well below maximum. Use external inductance to meet requirements. 3. t is recommended to connect a 100 μf / 100 V external bus capacitor between High Voltage and Power Ground. 4. Additional cooling and/or heatsink may be required to achieve rated performance. Page 3 of 7

4 PN FUNCTNS P1 - Signal Connector Pin Name Description / Notes / 1 +REF N Differential Reference nput (±10 V perating Range, ±15 V Maximum nput) 2 SGNAL GND Signal Ground GND 3 -REF N Differential Reference nput (±10 V perating Range, ±15 V Maximum nput) 4 CURRENT MNTR Current Monitor. Analog output signal proportional to the actual current output. Scaling is 13.5 A/V. Measure relative to signal ground. 5 NHBT N TTL level (+5 V) inhibit/enable input. Leave open to enable drive. Pull to ground to inhibit drive. nhibit turns off all power devices. 6 +V HALL UT Low Power Supply For Hall Sensors (+6 30 ma). Referenced to signal ground. Short circuit protected. 7 SGNAL GND Signal Ground GND 8 HALL 1 9 HALL 2* Single-ended Hall/Commutation Sensor nputs (+5 V logic level) 10 HALL 3 11 CURRENT REFERENCE Measures the command signal to the internal current-loop. This pin has a maximum output of ±7.3 V when the drive outputs maximum peak current. Measure relative to signal ground. 12 FAULT UT TTL level (+5 V) output becomes high when power devices are disabled due to at least one of the following conditions: inhibit, invalid Hall state, output short circuit, over voltage, over temperature, power-up reset. 13 RESERVED - 14 RESERVED - Reserved 15 RESERVED - 16 RESERVED - P2 and P3 - Power Connector Pin Name Description / Notes / 1b 1a HGH VLTAGE DC Power nput. 3A Continuous Current Rating Per Pin. t is recommended to connect a 2b 2a HGH VLTAGE 100 μf / 100 V external capacitor between High Voltage and Power Ground. 3b NC Not Connected (Reserved) - 3a NC (KEY) Key: No Connection (pin removed) for P2. Not Connected (Reserved) for P3. - 4b 4a PWR GND GND Power Ground (Common With Signal Ground). 3A Continuous Current Rating Per Pin. 5b 5a PWR GND GND 6b 6a MTR C 7b 7a MTR C 8b 8a MTR B Motor Phase utputs. Current output distributed equally across both P2 and P3 connectors 9b 9a MTR B 8 pins per motor phase, 3A continuous current carrying capacity per pin. 10b 10a MTR A 11b 11a MTR A *For use with Single Phase (Brushed) motors, ground Hall 2 and only connect motor leads to Motor A and Motor B. HARDWARE SETTNGS Jumper Settings The drive PCB is conformal coated, thereby making it difficult to change jumper settings. Jumpers are SMT 0 ohm resistors located on the underside of the drive PCB. By default, the drive is configured with the jumpers installed. Typical drive operation will not require the jumpers to be removed. Please contact the factory before jumper removal. Jumper Description Configuration SMT Jumper (0Ω Resistor) Not nstalled nstalled JE1 nhibit logic. Sets the logic level of inhibit pins. Labeled JE1 on the PCB of the drive. Low Enable Low nhibit JE2 Hall sensor phasing. Selects 120 or 60 degree commutation phasing. Labeled JE2 on the PCB of the drive. 60 degree 120 degree Page 4 of 7

5 MECHANCAL NFRMATN Connector nformation Mating Connector Details ncluded with Drive P1 - Signal Connector 16-pin, 2.54 mm spaced header Samtec: BCS-116-L-S-PE No 11 CURRENT REFERENCE 9 HALL 2 7 SGNAL GND 5 NHBT N 3 -REF N 1 +REF N 2 SGNAL GND 4 CURRENT MNTR 6 +V HALL UT 8 HALL 1 10 HALL 3 12 FAULT UT Connector nformation Mating Connector Details ncluded with Drive P2 - Power Connector 22-pin, 2.54 mm spaced, dual-row header Samtec: SSM-111-L-DV No PWR GND 5a PWR GND 4a NC (KEY) 3a HGH VLTAGE 2a HGH VLTAGE 1a 6a MTR C 7a MTR C 8a MTR B 9a MTR B 10a MTR A 11a MTR A HGH VLTAGE 1b HGH VLTAGE 2b NC 3b PWR GND 4b PWR GND 5b 6b 11b MTR A 10b MTR A 9b MTR B 8b MTR B 7b MTR C MTR C Connector nformation Mating Connector Details ncluded with Drive P3 - Power Connector 22-pin, 2.54 mm spaced, dual-row header Samtec: SSM-111-L-DV No PWR GND 5a PWR GND 4a NC 3a HGH VLTAGE 2a HGH VLTAGE 1a 6a MTR C 7a MTR C 8a MTR B 9a MTR B 10a MTR A 11a MTR A HGH VLTAGE 1b HGH VLTAGE 2b NC 3b PWR GND 4b PWR GND 5b 6b 11b MTR A 10b MTR A 9b MTR B 8b MTR B 7b MTR C MTR C Page 5 of 7

6 MUNTNG DMENSNS Page 6 of 7

7 PART NUMBERNG NFRMATN AZ X B 25 A 8 - AZ Analog Drive Series Environment ption X: EXTended Environmental Ratings Drive Type B: Brushless Drive, Analog Command BDC: Brushless Drive, PWM Command Feedback Supported Blank: Current Mode only E: Encoder Velocity Mode Available H: Hall velocity Mode Available Peak Current (Amps) 8: 8 Peak, 4 Continuous 15: 15 Peak, 7.5 Continuous 25: 25 Peak, 12.5 Continuous *ptions available for orders with sufficient volume. Contact ADVANCED Motion Controls for more information. Additional ptions* NV: nverted nhibit Logic Revision Assigned a letter (A through Z) by manufacturer Max DC Bus Voltage (1:10 in Volts) 8: 80 ADVANCED Motion Controls AZ series of servo drives are available in many configurations. Note that not all possible part number combinations are offered as standard drives. All models listed in the selection tables of the website are readily available, standard product offerings. ADVANCED Motion Controls also has the capability to promptly develop and deliver specified products for EMs with volume requests. ur Applications and Engineering Departments will work closely with your design team through all stages of development in order to provide the best servo drive solution for your system. Equipped with on-site manufacturing for quickturn customs capabilities, ADVANCED Motion Controls utilizes our years of engineering and manufacturing expertise to decrease your costs and time-to-market while increasing system quality and reliability. Examples of Modifications and Customized Products ntegration of Drive into Motor Housing ntegrate EM Circuitry onto Drive PCB Mount EM PCB onto Drive Without Cables Custom Control Loop Tuned to Motor Characteristics Multi-axis Configuration for Compact System Custom / nterface for System Compatibility Custom PCB and Baseplate for ptimized Footprint Preset Switches and Pots to Reduce User Setup RTV/Epoxy Components for High Vibration ptimized Switching Frequency EM Specified Connectors for nstant Compatibility Ramped Velocity Command for Smooth Acceleration EM Specified Silkscreen for Custom Appearance Remove Unused Features to Reduce EM Cost ncreased Thermal Limits for High Temp. peration Application Specific Current and Voltage Limits Feel free to contact Applications Engineering for further information and details. Available Accessories ADVANCED Motion Controls offers a variety of accessories designed to facilitate drive integration into a servo system. Visit to see which accessories will assist with your application design and implementation. Power Supplies Shunt Regulators Mounting Card MC1XAZ01 Filter Cards To Motor Drive(s) All specifications in this document are subject to change without written notice. Actual product may differ from pictures provided in this document. Page 7 of 7